*Solid, **Fastly.Cool** and gets the job done. For rooms where window-mounted air conditioning is not an option, this works very well. Easy set up, rapid cooling, and great design.*
Good video, I see a few issues. 1st of all - no thermal paste. Heat induction to the fins will not be optimum. 2nd issue: No adequate heat dissipation. Maybe try a water cooled heat sink/exchanger. 3rd issue : your temperature probe is kept inside the box. This is wrong. The A/C needs to cool the air outside the box. By placing the temperature sensor inside the box (very close to the heat sink on the cold side) you are displaying internal temperature, and not the AC effect outside the box. Viewers need to see the cooling effect on air outside the box. But keep it up. I liked the idea.
2nd - It need to go outside, otherwise he just creating more heat. Peltier is basically moving hot to one side and cold to the other and while doing it, it also creating a little bit of heat too (energy loss).
And did you noticed that the heat goes into the same room so it acts as heater? And the power supply should be in another room so it will not heat up air in the same room.
Trew Mika Power supply is creating heat, but not as much as just throwing the hot air back into the room from the peltier. It can still cool the room if the PSU is fairly efficient and the heat from the peltier goes outside. And as you said, he is just heating the room, which is dumb.
TEC-12706 cell takes about 4A and you have four, plus 0,9A fan, and you have two. I don't have any calculator with lcd display around me, but should make 17,8A, and you need some more just to be sure. Let's say 20 A power supply. And you have 10A power supply.
One tec 12706 need 12v 7 to 8a. 7×4=28a 12v 0.90a fan. Which are 0.90×2=1.8 almost 2a 4 small fans equal to almost 12 v 1a Tec=28 Two big fan 2 Four small fans 1 Answer is 31a Means you needs almost 12v 35a power supply. To run the project smoothly. 12v 10a which is 1/3 of the real need of power. This video is totally worth less. Matlab Kuch Bhi. Shame on you 😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡
Please answer If I want to use 3peltier and 3fan in a connection which one will be great,series or Perralal?and what parameter of dc power voltage that I should use?
I did too many experiments last summer and come to this conclusion that peltiers need too much energy and much more to balance the hot and cold side. Tremendous waste to time. So they r in store nowadays.
Design is good, few changes needed to be done like use of thermal paste, air input to sink need to be improved to increase more contact of input air with heat sink fins. For those who are worried for heat exhaust in same room a pipe can be attached or some other arrangements can be made depending on your placement. Again I am very much impressed with the design. Thanks for the video upload.
This is a great idea, but personally I'd have assembled it in a different order and prepared pieces before gluing them in place. Work smarter not harder.
Kerala 🌴TVM. 🌹Excellent job🌹You have proved your excellence and honesty. Many videos are watching we will not any idea. But you are marking on the components. So the technicians will get the idea.. You have to put your Name. Thnk you🌹🌹🌹🌹🌹 🙏🏾🙏🏾🙏🏾
Good concept but execution could be improved. I also understand building with limited resources but this was a lot of work for 2C delta T. Stacking the modules would improve cold side temp exponentially. Recirculating some cool air across the hot side will also help. Mounting a pulling fan directly over heat sink would also improve cold side discharge temp.
LOOOOLL.... 4 peltier useing power supply 10A.....hahahahahaha so funny 1 peltier 6A make parallel 6A x 4 = 24A and that doesn't include fans.....it is not enough to cool the room
4 Peltier x 6 A is not equal to 24 A. hahahah If you connect all +pos. to one 2mm wire and 2mm wire to SMPS +pos then it's just 4/5 A likewise all grounds need to be joint/soldred to one 2mm good wire --- > SMPS -neg. it's just simple Yes you need a Resistor for cpu fan it needs only 1A and 12v, so add 7812 regulator IC for max. 1 A Output Total Wattage of System = 1A Fan x 12v x 2 pcs = 24 W 6A Peltier x 12v = 72 W Total system watt = 96 Watts DC THE AIR CONDITIONER MADE BY THE PERSON IS CALLED WINDOW AIR CONDITIONER And not Split one. So You need a Hollow Window in room facing gallery / backside lawn , so it will cool by throwing hotness of peltier. ACs work similarly. In new age of Split AC, The Box is cut into 2 pieces, but working remains the same ! It doesn't throw out hot air of room, it just cools room air and throw away AC System Heat outside
Buen vídeo compañero...pero otra vez me deja de poner la pasta térmica, con lo cual, el rendimiento de sus células Peltier no es el idóneo....gracias por compartir...
An excellent project. However I noticed 4x 6 amp peltiers (total 24 amp) and the power supply is rated to 10 amp? No thermal paste ? How long can this run before it burns out ? The placing of the temp censor on the plate that is connected directly to the cold plate on the peltier will give an artificially low reading. The heat exhaust is venting in to the same room so room temperature will actually rise due to inefficiency of the peltiers.
Nice video👍 It is an Air Cooler The temperature is inside to show the temperature that comes out.. It would not make the whole room cold like air conditioner but it keeps you cool when you are hit by it.. respect and understand the project before over reacting😊 Tnx
I am trying to make a version where the hot heat sinks are in a big container of cold water with ice in it... Then if I change out the water regularly it will make the whole room cooler
its good toy AC, but real working AC ca be made using peltier, 100% possible but would require 56 peltier (12706) surface conduction area approximately 200 square inches , its performance will meet 2 Ton AC. 01 (12706) peltier takes 3.5 amp . 56 will take 196 Amp 56*3.5=196*12v=2352 watts and 200 Watts for blowers, total load 2552 Watts. However thermal insulation is critical point. it will obviously save energy with smart and quite design, no noise, no starting heavy current, no motor induction losses and no wear parts. it will roughly cost 250$
It is real AC ! i think 4 fan and i peltier will not work, and 1 fan and 4 peltier can cool 100sqft space in approx 1.5 hours. u can call it toy ac, but it really works, Higher CFM fan can be deployed but it will suck more, and peltier will not be able to supply more cool air, so lower cfm is good idea ! SO What it can run on solar panels of 100watt
Good effort. If you add a diode bridge to the fan's you can simply swap the polarity to the peltier's to reverse the heat flow, therefore a switch could be used to make it reverse cycle. It's also better to use liquid heat exchangers with peltier's as it stops the airconditioner from becoming a heat exchanger itself when it's not powered on, especially good if you plan to fit it in a wall. I did one using liquid CPU coolers with a little radiator in each side. Works from a 250 watt solar panel and keeps the temp down a few degrees with zero running cost.
@@irtzashahanpk My office room is well insulated (R-10), and it takes a few days of heat to start getting hot inside, but with that system always on when the sun shines it keeps it at about 22C, where without it it used to creep up to 30C. The effect is small, but over a long period it makes a fair difference. I get a similar benefit in winter, it adds a few degrees on cold sunny days, not sure how much as I still run extra heating, but it's never freezing when I come in at evenings.
I am trying to set up a peltier 12706, supplying power from a 12 Volt, 6 Amp transformer rectifying & filtering it into 12 V DC. At first the heat sinks on the hot side is heating up and cold side is cooling respectively. A few minutes later the cold side is also heating up. How to rectify this?
It will not be enough to reach the satisfaction level, also 'put the meter in the middle of the room not in front of the peltier' to see if the room changes its temp. I suggest a water dripping style using a Box fan, powerheads, pvc and filter pads more effective
I'm new to this Peltier stuff. I have bought an assembled Peltier with one heatsink on each side of the chip and one water block each side and fan. I see a lot of heating and cooling functions. how is this determained if it cools or heats? I need mine to cool the water flowing trough for a Laser Engraver.
You haven't shown that how much down temp fall. But your work is very nice.. if you help me, I will make it. I hv some question sir.. plz help me by responding. How much total cost of your created ac? What is white board you were using? Is it thermocole? What adhesive you used ? Will this portable AC cool a room of 1000 sqft?? A 10 x 10 feet room?? You used a heatsink with peltier. What I should tell to shopkeeper about the exact heatsinks..? Thanks and regards
One tec 12706 need 12v 7 to 8a. 7×4=28a 12v 0.90a fan. Which are 0.90×2=1.8 almost 2a 4 small fans equal to almost 12 v 1a Tec=28 Two big fan 2 Four small fans 1 Answer is 31a Means you needs almost 12v 35a power supply. To run the project smoothly. 12v 10a which is 1/3 of the real need of power. This video is totally worth less. Matlab Kuch Bhi. Shame on you 😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡
It would be more efficient if you also block a portion of the sinks so air would be need to run through more length of the fins, giving it more time to cooler down.
I think he used 4 x 6A Peltier with 10A Power supply, If each of these peltier draws less current (divided current) both chill and hot side will be very less, try using 30A power supply, may that will provide enough current and Real AC effect + use Thermal compound for efficient heat and freeze transfer, but then again it will freeze fast, you may need to use high Rotation fan (16000rpm) for efficiency, Just my thought.
This is really good brother. Now try to discover a way to drop the temperature even further. The thermal compound grease as already suggested will improve things. Personally I would have the fans directly bolted to the sinks. There are obviously many ways to skin a cat. 5☆ for good honor and effort...
Air needs to sweep over maximum possible length over the heatsink fins for better conduction. Design and placement of components is perfect. I liked it 👌
The problem still arises due to hot & cold issue 80%vs 20%but its nice to see such activity like this lods thanks for sharing sabi ang idea ay nagiging perfect the more we're trying.
Nice model. But only 2 to 3 degree C fall in temperature is not expected while watching. Keep rocking. Bdw which material is that which looks like dense thermacole? I think it will consume too much Power (wattage).
When Degge is 29.1 after use 4 peltier and degree not 2 - 3 degree down ..minimum 8 degree men 20 up degree down... use water block ....cool cooler water and show degree fast and last...
I liked your project very much, but by doing a little editing in it, it can be a very successful project. Editing - - Both heat sink plates should be installed on the side instead of top down, then close the front and back completely by card bord, the fan will stay where it is, the air will enter from the side and will cool twice and come to the front, and so on After entering air from the side, it will heat up and come out of the back, ... If you like the suggestion, then reply.
Yes it can. Use peltier module in conjunction with a swamp cool/water cooler. Use it to cool the recirculating water with probably 3 or 4 modules and the air you would get to almost freezing in no time.
Large Space cooling ? yeah can be achieved. Fans come in CFM cubic feet per minute size. So if your LArge room is about 20ft x 20ft , and you're fan has max 60cfm capacity, then you will need 20x20 = 400 sq.ft / Divd by 60 cfm = 6 Fans of such cfm value. But you will need 12 fans of such cfm value, 6 fans of 60cfm value and 6 fans(heat throwing) of higher than 60cfm value. Peltier : you will need peltier qty as per above video multiplication. 1 Fan with 4 peltiers so 6 Fans peltier qty will be will be ??? 6 x 4 = 24 peltiers Total System Cost will be yeah much highe 24 pelts x 200INR = 4800 INR (USD approx $70) 12 Fans x 250INR = 3000 INR (USD approx $60) 24 Heat Sinks x 200 INR = 4800 INR (USD approx $70) Insulation, wires, smps = 8000 INR ( USD approx $150) acrylic fom sheet etc. Total System Cost = 20,600 INR (USD approx $300)
@@shreyaskumar5366 can you tell what other cooling methods are way better than peltier?? It would help if you can offer solutions and not just to comment negatively. Jas saying. Also post video of what you said is better then we can truly understand and appreciate it
If I use an evaporator and fan behind it ... like the one used in air conditioners ... and pass water chilleded by pletiers inside the evaporator ... where the temperature of this water reaches -20 degrees Celsius after adding an antifreeze to the water ... Will I get enough coolness to cool a room and how many pletiers do I need to do that?
no es bueno usar pega, porque cuando sea necesario hacer mantenimiento o limpiar el polvo de los difusores y de los ventiladores será un verdadero problema, es mejor fijar con tornillos.
Nice that at one end cool air comes out, now, if you blow the hot air out of the back you did not gain much.... You need that hot air out of the room.... that is the idea of an air conditioner.
For the circuit diagram please visit here
shorturl.at/FNS56
electronicshelpcare.com
Electronic ac parts name
How much time can i use it continously
music name please.
How long can we use it continuesly
Sepang curcit fomula one
*Solid, **Fastly.Cool** and gets the job done. For rooms where window-mounted air conditioning is not an option, this works very well. Easy set up, rapid cooling, and great design.*
Good video,
I see a few issues.
1st of all - no thermal paste.
Heat induction to the fins will not be optimum.
2nd issue:
No adequate heat dissipation. Maybe try a water cooled heat sink/exchanger.
3rd issue : your temperature probe is kept inside the box.
This is wrong.
The A/C needs to cool the air outside the box.
By placing the temperature sensor inside the box (very close to the heat sink on the cold side) you are displaying internal temperature, and not the AC effect outside the box.
Viewers need to see the cooling effect on air outside the box.
But keep it up.
I liked the idea.
2nd - It need to go outside, otherwise he just creating more heat.
Peltier is basically moving hot to one side and cold to the other and while doing it, it also creating a little bit of heat too (energy loss).
And did you noticed that the heat goes into the same room so it acts as heater? And the power supply should be in another room so it will not heat up air in the same room.
Trew Mika
Power supply is creating heat, but not as much as just throwing the hot air back into the room from the peltier.
It can still cool the room if the PSU is fairly efficient and the heat from the peltier goes outside.
And as you said, he is just heating the room, which is dumb.
@@trewmika1869 you actually believe this thing can cool a room ha ha ha more like cooling a roach motel.
Best comment. Kiss tap a little bit then hug
TEC-12706 cell takes about 4A and you have four, plus 0,9A fan, and you have two. I don't have any calculator with lcd display around me, but should make 17,8A, and you need some more just to be sure. Let's say 20 A power supply. And you have 10A power supply.
One tec 12706 need 12v 7 to 8a.
7×4=28a
12v 0.90a fan. Which are 0.90×2=1.8 almost 2a
4 small fans equal to almost 12 v 1a
Tec=28
Two big fan 2
Four small fans 1
Answer is 31a
Means you needs almost 12v 35a power supply. To run the project smoothly.
12v 10a which is 1/3 of the real need of power. This video is totally worth less.
Matlab Kuch Bhi. Shame on you 😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡
:/
@@dsrgaming5kviews1hourago..97 if runs in maximum amperage the joule effect ruins everything. 3A is the sweet spot for 12706.
It actually doesn’t matter . Even it without working he is making money .
Truee
Please visit for amplifier circuit diagram
electronicshelpcare.net
Please answer
If I want to use 3peltier and 3fan in a connection which one will be great,series or Perralal?and what parameter of dc power voltage that I should use?
I did too many experiments last summer and come to this conclusion that peltiers need too much energy and much more to balance the hot and cold side. Tremendous waste to time. So they r in store nowadays.
Se você me dá uma pastilha que congela
Design is good, few changes needed to be done like use of thermal paste, air input to sink need to be improved to increase more contact of input air with heat sink fins. For those who are worried for heat exhaust in same room a pipe can be attached or some other arrangements can be made depending on your placement. Again I am very much impressed with the design. Thanks for the video upload.
Its pretty kool see someone else do this.. brings back great memories
Try using thermal paste or thermally conductive epoxy
Thermal paste is not necessary
@@TurboElectricLtd Nope, you need thermal paste.
This is a great idea, but personally I'd have assembled it in a different order and prepared pieces before gluing them in place. Work smarter not harder.
Kerala 🌴TVM. 🌹Excellent job🌹You have proved your excellence and honesty. Many videos are watching we will not any idea. But you are marking on the components. So the technicians will get the idea.. You have to put your Name. Thnk you🌹🌹🌹🌹🌹 🙏🏾🙏🏾🙏🏾
Please use thermal paste while heat transmission to heat sink
And if him connect on series the plates the result is better.
@@alleluijah how can this bring cool instead of the normal air fan produces
yes
Exactly
No need if we have thread😁
The hot side of the TEC needs around 4 times the heatsink surface area than the cold side does.
also the lack of thermal paste is going to cause them to burn out quickly.
Best pure country music,many thanks for the explanation,thanks also patietly.
You should use thermal paste
I wonder what you do with all the condensation after turn off
Good concept but execution could be improved. I also understand building with limited resources but this was a lot of work for 2C delta T. Stacking the modules would improve cold side temp exponentially. Recirculating some cool air across the hot side will also help. Mounting a pulling fan directly over heat sink would also improve cold side discharge temp.
LOOOOLL.... 4 peltier useing power supply 10A.....hahahahahaha so funny 1 peltier 6A make parallel 6A x 4 = 24A and that doesn't include fans.....it is not enough to cool the room
4 Peltier x 6 A is not equal to 24 A. hahahah
If you connect all +pos. to one 2mm wire and 2mm wire to SMPS +pos then it's just 4/5 A
likewise all grounds need to be joint/soldred to one 2mm good wire --- > SMPS -neg. it's just simple
Yes you need a Resistor for cpu fan it needs only 1A and 12v, so add 7812 regulator IC for max. 1 A Output
Total Wattage of System =
1A Fan x 12v x 2 pcs = 24 W
6A Peltier x 12v = 72 W
Total system watt = 96 Watts DC
THE AIR CONDITIONER MADE BY THE PERSON IS CALLED WINDOW AIR CONDITIONER
And not Split one. So You need a Hollow Window in room facing gallery / backside lawn , so it will cool by throwing hotness of peltier. ACs work similarly.
In new age of Split AC, The Box is cut into 2 pieces, but working remains the same ! It doesn't throw out hot air
of room, it just cools room air and throw away AC System Heat outside
Buen vídeo compañero...pero otra vez me deja de poner la pasta térmica, con lo cual, el rendimiento de sus células Peltier no es el idóneo....gracias por compartir...
An excellent project.
However I noticed 4x 6 amp peltiers (total 24 amp) and the power supply is rated to 10 amp?
No thermal paste ? How long can this run before it burns out ?
The placing of the temp censor on the plate that is connected directly to the cold plate on the peltier will give an artificially low reading.
The heat exhaust is venting in to the same room so room temperature will actually rise due to inefficiency of the peltiers.
Nice video👍
It is an Air Cooler
The temperature is inside to show the temperature that comes out..
It would not make the whole room cold like air conditioner but it keeps you cool when you are hit by it.. respect and understand the project before over reacting😊
Tnx
I am trying to make a version where the hot heat sinks are in a big container of cold water with ice in it... Then if I change out the water regularly it will make the whole room cooler
@@parzival9639 hope you can make a video of it and pls tag me....nice idea....
Idea is good but you need redesign it. For better conduction. And your wireing too critical follow the easy path.
its good toy AC, but real working AC ca be made using peltier, 100% possible but would require 56 peltier (12706) surface conduction area approximately 200 square inches , its performance will meet 2 Ton AC.
01 (12706) peltier takes 3.5 amp . 56 will take 196 Amp 56*3.5=196*12v=2352 watts and 200 Watts for blowers, total load 2552 Watts. However thermal insulation is critical point.
it will obviously save energy with smart and quite design, no noise, no starting heavy current, no motor induction losses and no wear parts. it will roughly cost 250$
is it possible long life,? sir
2552watts/20= 212.6.A .....
212.6/20 = 10AMPS in 230volts
@@sudeepaugustian167 use a car battry :)
u r so telented bro
It is real AC ! i think 4 fan and i peltier will not work, and 1 fan and 4 peltier can cool 100sqft space in approx 1.5 hours. u can call it toy ac, but it really works, Higher CFM fan can be deployed but it will suck more, and peltier will not be able to supply more cool air, so lower cfm is good idea !
SO What it can run on solar panels of 100watt
Видео о том, как сделать из хороших вещей - мусор! Этот прибор будет больше нагревать комнату, нежели охлаждать.
can you use silicone sealant in sealing those sides instead of glue gun?
There is no need for such a process for 2 C temperature.
That's the same thing that I thought. Plus, the hot air is still in the same vacinity as the cooled air.
Good effort.
If you add a diode bridge to the fan's you can simply swap the polarity to the peltier's to reverse the heat flow, therefore a switch could be used to make it reverse cycle.
It's also better to use liquid heat exchangers with peltier's as it stops the airconditioner from becoming a heat exchanger itself when it's not powered on, especially good
if you plan to fit it in a wall. I did one using liquid CPU coolers with a little radiator in each side. Works from a 250 watt solar panel and keeps the temp down a few degrees
with zero running cost.
how many Degrees ? And in fahrenheit or Celsius.
@@irtzashahanpk My office room is well insulated (R-10), and it takes a few days of heat to start getting hot inside, but with that system always on when the sun shines it keeps it at about 22C, where without it it used to creep up to 30C. The effect is small, but over a long period it makes a fair difference. I get a similar benefit in winter, it adds a few degrees on cold sunny days, not sure how much as I still run extra heating, but it's never freezing when I come in at evenings.
Great improvement ideas..!!!!
I am trying to set up a peltier 12706, supplying power from a 12 Volt, 6 Amp transformer rectifying & filtering it into 12 V DC. At first the heat sinks on the hot side is heating up and cold side is cooling respectively. A few minutes later the cold side is also heating up. How to rectify this?
Awesome, i like your confidence k ri on
Thermometer tail should sense room temperature, not the module cold side temperature.
nice heater for the winter time...)))
Heat exhaustion in the same room 🤣🤣🤣🤣👏👏👏
Better to overcome the heat-cold issue just detouch both the modules and keep an insulator between them, then it works well.
It will not be enough to reach the satisfaction level, also 'put the meter in the middle of the room not in front of the peltier' to see if the room changes its temp. I suggest a water dripping style using a Box fan, powerheads, pvc and filter pads more effective
You should use both of sides idia.
It is my way to think but it is nice
Idia.thanks.
It will equal the room temperature as before as la chatelier law, 😂 with both hot and cool air until you set the hot side somehow outside the room.
put it in window.
thats how ac works and he built it
You are asking too much for someone who tie the heat sinks with a string. Cheaper does not means poor quality, this is poor quality.
I'm new to this Peltier stuff. I have bought an assembled Peltier with one heatsink on each side of the chip and one water block each side and fan. I see a lot of heating and cooling functions. how is this determained if it cools or heats? I need mine to cool the water flowing trough for a Laser Engraver.
step1- hold the peltier between your index & thumb.
step2- connect power.
step3- one side will burn you a nd the other will freeze.
you're welcome
From where you had bought the assembled peltier?
You haven't shown that how much down temp fall. But your work is very nice.. if you help me, I will make it. I hv some question sir.. plz help me by responding.
How much total cost of your created ac?
What is white board you were using? Is it thermocole? What adhesive you used ?
Will this portable AC cool a room of 1000 sqft?? A 10 x 10 feet room??
You used a heatsink with peltier. What I should tell to shopkeeper about the exact heatsinks..?
Thanks and regards
1200
1000 SQ feet ?
With 4 peltiers ?
Even a 2 ton AC finds it tough to cool 1000 sq ft.
Contact mee
For how long you can use continuesly the airconnditioner?
Please visit for the best Bass tone circuit diagram
electronicshelpcare.net/bass-tone-circuit-diagram/.
hi bro. i like this background music.
One tec 12706 need 12v 7 to 8a.
7×4=28a
12v 0.90a fan. Which are 0.90×2=1.8 almost 2a
4 small fans equal to almost 12 v 1a
Tec=28
Two big fan 2
Four small fans 1
Answer is 31a
Means you needs almost 12v 35a power supply. To run the project smoothly.
12v 10a which is 1/3 of the real need of power. This video is totally worth less.
Matlab Kuch Bhi. Shame on you 😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡😡
What is the name of the song in the background
Bro I appreciate your intelligence & must say it's a brilliant idea. Good luck for future projects.
you're genius carry on man i like your channel ✌❤
thank you sir its my pleasure 😊✌👐
Excellent work!
It would be more efficient if you also block a portion of the sinks so air would be need to run through more length of the fins, giving it more time to cooler down.
I think he used 4 x 6A Peltier with 10A Power supply, If each of these peltier draws less current (divided current) both chill and hot side will be very less, try using 30A power supply, may that will provide enough current and Real AC effect + use Thermal compound for efficient heat and freeze transfer, but then again it will freeze fast, you may need to use high Rotation fan (16000rpm) for efficiency, Just my thought.
"freeze transfer" is not a thing. Only heat transfer exists. Cold is just lack of heat. Because it has been transferred elsewhere.
This is really good brother. Now try to discover a way to drop the temperature even further. The thermal compound grease as already suggested will improve things. Personally I would have the fans directly bolted to the sinks. There are obviously many ways to skin a cat.
5☆ for good honor and effort...
Air needs to sweep over maximum possible length over the heatsink fins for better conduction. Design and placement of components is perfect. I liked it 👌
Gobble goblin to the show is a bit more about our products
That was more width than length, should have put them side by side elongated not on top of each other in my opinion
Hi the fan on the hot side of the thermoelectric does it blows in or out???
Great Idea! use the cool side in the summer and the hot side in the winter -
The problem still arises due to hot & cold issue 80%vs 20%but its nice to see such activity like this lods thanks for sharing sabi ang idea ay nagiging perfect the more we're trying.
Neat work Thumbs up 👍
A great deal of labor but the result not very impressive, the temperature should have gone to 17 degree in order to make this project worth its labor
How do you do that?
In my country, now, the temperature about 48 degree, if i use the peltier , it is go down to 46 only 2 degree🤔 so i still 😥
Well i believe peltier is not meant for countries like ours. We get 55 degrees some time
So the hot side of the Peltier is blown into the room also? Nice heater you have there.
Nice model. But only 2 to 3 degree C fall in temperature is not expected while watching. Keep rocking. Bdw which material is that which looks like dense thermacole? I think it will consume too much Power (wattage).
When Degge is 29.1 after use 4 peltier and degree not 2 - 3 degree down ..minimum 8 degree men 20 up degree down... use water block ....cool cooler water and show degree fast and last...
That's nice mini air-conditioning, but how efficient is it, especially in desert climate?
I liked your project very much, but by doing a little editing in it, it can be a very successful project.
Editing - - Both heat sink plates should be installed on the side instead of top down, then close the front and back completely by card bord, the fan will stay where it is, the air will enter from the side and will cool twice and come to the front, and so on After entering air from the side, it will heat up and come out of the back, ... If you like the suggestion, then reply.
Sir do this air conditioner cools theentire room? Or works like a fan?
The music is too nice,What is that's name?
Now i am death feeling after watch this clip.
😢
¿Y puedes hacerlo funcionar con pilas o cargador solar?
The glue will melt on the hot side.
All this work for 2 degrees, youre a genius
How much power consumption?
Music is, Promontory from the Last of the Mohicans soundtrack
loved the music specially
Bhai hot side m thermal paste lsgane se jaida cooling milta
using thermal paste between the heatsinks and the pads would have taken those temps to the 19deg mark...
What power supply do you use? I mean specs?
The idea is good, but I want you to help me with this question: to run 3 or 4 12v fans is it necessary to use those peltiers?
Any one can answer this question? Because we are the same question
This method cannot be used to cool a large space economically.
Yes it can. Use peltier module in conjunction with a swamp cool/water cooler. Use it to cool the recirculating water with probably 3 or 4 modules and the air you would get to almost freezing in no time.
Large Space cooling ? yeah can be achieved. Fans come in CFM cubic feet per minute size.
So if your LArge room is about 20ft x 20ft , and you're fan has max 60cfm capacity, then you will need
20x20 = 400 sq.ft / Divd by 60 cfm = 6 Fans of such cfm value.
But you will need 12 fans of such cfm value, 6 fans of 60cfm value and 6 fans(heat throwing) of higher
than 60cfm value.
Peltier : you will need peltier qty as per above video multiplication. 1 Fan with 4 peltiers
so 6 Fans peltier qty will be will be ???
6 x 4 = 24 peltiers
Total System Cost will be yeah much highe
24 pelts x 200INR = 4800 INR (USD approx $70)
12 Fans x 250INR = 3000 INR (USD approx $60)
24 Heat Sinks x 200 INR = 4800 INR (USD approx $70)
Insulation, wires, smps = 8000 INR ( USD approx $150)
acrylic fom sheet etc.
Total System Cost = 20,600 INR (USD approx $300)
Never think "economical" whenever using a peltier module in your project....they are very less efficient as compared to other cooling methods
@@shreyaskumar5366 can you tell what other cooling methods are way better than peltier?? It would help if you can offer solutions and not just to comment negatively. Jas saying. Also post video of what you said is better then we can truly understand and appreciate it
Olá queria saber se estala 6 pastilhas nessa fonte
Each peltier module draws at least 60Watts, you cannot use a 120W power supply
11:20 how you put the silicone on the hot side?!!
attractive work
it can last for how many hours?
Bhai ki mehnat ko slam
Nice concept.. but if you place the waterblock+aquarium pump will result to reduce the hot side...
Which board do you use? What is the name Of that board?
Super Information
Keep Good Work. Thanks Brother👌👌
U r using 4* pelteir module each 6amps and u are giving only 10amps u have to use minimum 12v 30amps for this 4 pelteir module 👍
熱電ペルチェモジュールは ならべるより重ねる方が冷たくなりますよ
Upto what degree we can cool. . . .and need to know how much watts it consume
210 watts almost
Deveria ter ligado as pastilhas em série, teria uma temperatura mais baixa e uma corrente elétrica menor.
Works well in our small garage that holds exercise equipment in
If I use an evaporator and fan behind it ... like the one used in air conditioners ... and pass water chilleded by pletiers inside the evaporator ... where the temperature of this water reaches -20 degrees Celsius after adding an antifreeze to the water ... Will I get enough coolness to cool a room and how many pletiers do I need to do that?
81f is not bad, some improvements could be made, would love to see 33f out of this but must settle for 81f.
did you use glue or thermopaste?
no es bueno usar pega, porque cuando sea necesario hacer mantenimiento o limpiar el polvo de los difusores y de los ventiladores será un verdadero problema, es mejor fijar con tornillos.
can 12v5A adopter can supply the single thermoelectic module(12v6v)?
for 4 peltiers cannot..
Why you dont use a theormal paste to more heatage?
GOOD WORK
Really great idea.
the hot side it's gonna make a nice work with the cables and the hot glue xD
LOL
Thank u so much. Super.
Writing the HOT and COLD on both sides. Why just only HOT and the other side must be COLD.
IS there any other phase?
using 4 peltier module i thik it should be temp below -2° but its 27.6° 😒
This is the worst design I've ever seen
The more of them you use, the less efficient it becomes.
@@plankhill That's only true if you pile them on top of eachother.
Video problem was insufficient cooling on the hot side.
Nice that at one end cool air comes out, now, if you blow the hot air out of the back you did not gain much.... You need that hot air out of the room.... that is the idea of an air conditioner.
Alhamdulillah, video is very good