Before You Buy a Kohler One Piece Toilet, Watch this Video on Replacing a Toilet Seat.
Вставка
- Опубліковано 5 вер 2024
- This video demonstrates how to and how not to replaced a toilet seat on a Kohler One Piece Toilet. If you like this video PLEASE SUBSCRIBE TO MY CHANNEL so UA-cam shares its advertising revenue! Thanks!!!!
Excellent source of information on how to tackle this problem.Thank you so much.
I found that Home Depot no longer stock the Everbilt 1 1/16" expansion (or well) nuts. But my local Ace hardware store had a drawer with 1 1/2" #10-32 well nuts for which I got #10-32 3" stainless steel pan-head screws. These have a much more substantial head than the #10-32 1 1/2" Everbilt screws and are needed to reach the 1 1/2" well nut. Be sure to put the #HK36 adapter over the well nut before you tighten the screw to expand the well nut and wedge it in place. On my first attempt the screw was drawn into the soft rubber of the well nut and would not come out so I had to sacrifice it by drilling it out and then doing it the right way with the #HK36 adapter in place before cinching up the well nut to wedge it in place. The EverBilt stainless screws have puny heads and you should insert and extra washer into the #HK36 adapter before tightening it up to prevent the screw head pulling through the #HK36 hole into the well nut soft rubber upper.
Where do you find the adapter at? I’m in a pickle now with this toilet seat. Thanks for the helpful information
@@Meem715 i use shoe goo to glue in standard bolts. dont bother with any kohler parts again.
Great to know. Thanks for sharing all of this information!!!
Thank you so much for this video. I wanted to replace our toilet seat and found that one of the anchors was spinning. Before I went to far with the project I found your video and am glad I did. Before I cut anything off and ended up at a dead end and without a seat I ordered the anchors you suggested. With the knowledge and guidance you provided I was able to remove the old and install the new in half an hour. Thank you again!
Fantastic! Thanks for letting me know!
Thank you so much for doing this video. I struggled with the same problem for about a year and was not able to remove the bolts no matter how much wd 40 I put on them. After watching your video, I was able to remove the bolts and the expansion nuts. I got to Home Depot and was able to purchase the screws and the expansion nuts but I could not find the adapter from Bemis. The new toilet seat I bought came with 2 plastic bolts and wing nuts which were intended for a toilet that one could get to the bottom and screw in the bolt/nut. So I took a hack saw and cut off the head of the plastic bolts, drilled a hole in the middle of each bolt head and used them in place of the Bemis adapter. It worked!
Thank you so-o-o-o much for this step-by-step video, including holding up the packages you used for each piece. I wrote it all down and then went shopping at Home Depot. Can't believe it took me TWO YEARS to get the toilet seat replaced, and it should have only taken 15 minutes. Like another commenter, I couldn't find the adapter kit you held up for the Bemis seat. I had purchased a Bemis/Mayfair seat like you did, so I just called the Bemis -800 phone number. Lo and behold, the super-helpful customer service woman sent me an adapter kit FREE that I received in two days. It had a whole lot of pieces, (including some that may have been useful instead of the expansion nuts [although they looked a little too wide]), but the white nylon adapters that you showed were exactly the same. Ya hoo!
Keep on recording, David. Your video was one of the most helpful I have seen on any topic.
Thanks Dawn, I so glad the video was helpful!! Crazy stuff!
I am at 3 months' mark. Today new dremel bits arrived. Looks like it will probably take me another few months.
Easy to install, ua-cam.com/users/postUgkxjA-hDN2m8_mi0Dg0JD8U6QiArozIAc4I and comfortable. No idea what other people were talking about when they said it was difficult to install or uncomfortable.
LOL, apparently Kohler has got the bots going to make the best of this post. Well I am just in the process of replacing the 10th flapper on my toilet, so I wish there was a bot to do that!! I watched the Kohler video on how to replace it and they cut when they talk about removing the old flapper bar. They cut, because its very difficult to pull the old bar out and they don't want you to realize how tough this is. Not surprisingly, they have also removed the ability to post a comment below their video, as I suspect many customers were complaining about how difficult the process is. I may make a Toilet from Hell, Part 2 video to show what is involved in removing the plastic flapper bar.
Same issue. However I went down this path serval time, just like you, maybe more. But thank God for your video. I was just about to order another Kohler anchor. But started another round of my UA-cam search and found your video. I am going to Home Depot and maybe Menards TODAY. Thank You. 👍
Very grateful that you made this video. I recently purchased a home that had this toilet installed and I came across this indefinitely spinning of the screws. Your solution saved me loads of time! Thank you.
This was a great source of information. I probably would have been talked into a new toilet if I hadn't seen this. I found the expansion nuts at Menards and bought stainless steel screws and washers. At the end I had the original seat firmly in place. Fingers crossed that it will be easier if there's a next time.
I didn't have a problem with removing the bolt and anchord, but couldn't figure out where to get the parts. Thank you for this very instrictive video.
Oh my god THANK YOU. I just bought a house and it came with a shitty (no pun intended) one piece Kohler with loose rusted bolts. I literally took screenshots of the pieces that worked for you and am going to find them now. Thank you, thank you for making my life 100000% easier (still annoying as hell but so much easier relatively)!!
Glad to be of assistance. I hope it all goes well for you!!
Thank you. I remember the toilet had a lifetime warranty. I wonder if Kohler will replace it or send and person here to change the toilet seat. No one wants to do it for fear of braking the toilet.
We are having the exact same problem. Bought a toilet seat over a year ago and couldn’t get it off. After watching your video now I know why we are having a problem. They need to stop selling these types of seats. Also Kohler toilet seat then was $50 to replace it. That is just unbelievable to me and I will never hold this company in high standards anymore. We still have not been able to remove the seat.
Your video was an absolute lifesaver - thank you! I've never had so much trouble with a dang toilet seat. Such an incredibly bad design! Thanks to you, I pried the dreadful metal expansion nuts out, went over to Home Depot and got the rubber ones you suggested, and sorted it. No more Kohler products for me!
Thank you so much for sharing this. I bought a Sanilo seat which is said to fit all manufacturers’ toilets. But low and behold this was not going to be my normal replacement process. Exact same problems as you described. And reaching Koehler and Sanilo support has been frustrating. I am 1 week in on this nightmare. But you have saved the day! I didn’t want any of the Koehler seats. This one matches the bathroom decor and is more sturdy than the original seat from when I purchased my condo. I can’t believe the drama? Again, Thank you so much.
Hi Kim, So glad to hear the video was helpful!! Also, its always good to know I'm not alone in my struggles!
So helpful, David! Just ordered everything at Home Depot. Specifically, Everbuilt Expansion Nuts #10-32x1-1/16" in brass and #10-32x1-1/2 stainless steel machine screws and the Kohler Seat Anchor Kit 84999. I threw in a few washers as well.
How did it work out?
Thank you very much for the specs on the Expansion Nut and Screw. Saved me SOOO much time. I can't believe how poorly designed this toilet is. Your video saved me hours of work and frustration. TY TY
Christopher, I'm so glad to hear it helped you avoid some of the insanity others have been going through.
Not bad...for a job that (on any other toilet) would taken 10 minutes max! But I'm glad I found your video. We need to change out one of these and this will be very helpful!
Hi David - a very helpful video and here here - what a pain it is to try to do this! You helped me figure out that I could remove the anchor, which snapped halfway down its length, even after I used plenty of WD-40 to attempt to overcome the corrosion. I ended up placing an 1/8" thick piece of rubber onto the porcelain, then a 1/4" thick piece of oak and then using a pry bar to pull out the screw and anchor. To provide a new anchor I ground down a 1/2 nylon dry wall anchor and glued it in place with epoxy resin. I then used a stainless steel sheet metal screw of the right diameter (+ a the original washer) which held the lid hinge firmly in place. Mission accomplished.
Wow, very ingenious!
Toilet from hell is a very suitable title for this! I’m on day 4 trying to change a toilet seat. Just got the bolts out.
Bro…This video is a lifesaver. Thanks for sharing. I had same problem and fixed it after watching this!!!
David, you are my hero. I have a Toto soft close with the same issue and yours is the only helpful video I found. The replacement directions on our model are straightforward however ours is CONCEALED like yours with no way to access the tightening nuts provided without tentacles (which I do not possess). I don't know why toilet designers do things like this, there are many working designs around this on later concealed toilet designs unfortunately ours is an older model before reason and common sense kicked in. I'm now off to Home Depot or Amazon for expansion nuts.
Dumb things drive me bonkers and I can really feel your pain. I'm glad you resolved this nonsense and hopefully I will too.
Glad the video was helpful. I hope it all worked out!
Thank you! I followed everything, My old seat was still attached - I got one anchor out because it broke while trying, then yanked on the seat until the second anchor came out. Installing the new anchors- yep I broke one of Kohler's $12 aluminum anchors, and had to drill it into the cavity in the toilet. Waiting for a new set from Amazon, so I'll get 2 more chances. yay!!
How did it work out?
Got it done with the new anchor! Got the new set for free, returned the first one to amz as defective.
I will never buy a one piece toilet
I tried everything until I finally stumbled upon a merchant at EBay who sold the correct hardware: the expansion nut with the hex hedge screw and the regular screw, and also the bolt that made it possible to hold the hex hedge screw in place while tightening to expand.
I'm stuck with 97 of these at work, I do hotel maintenance. 😅, any other toilet, it's a 2 minute job to fix. Definitely going to the less expensive seat and fasteners you used. Good job!
Wow, I can't even imagine 97 of these units!!! What a nightmare!
97 Kohler 1.6 gallon one piece toilets??? My gosh that’s horrible I am stuck with one and I can’t twist the screw wing twist since the hole is like half an inch in diameter or something like that. Why on Earth would Kohler make such a badly designed toilet in which you have so much trouble changing a seat???
If you have to pull the bolt out, it can be helpful to hit it sideways a few times to loosen it. Hit it in one direction once, then in the opposite direction once, and repeat this a few times. I also had to drill one of the bolts out, and I started with a very small diameter bit angled at about a 45 degree angle and drilled to eat away at the metal. I gradually worked up to slightly larger diameter bits, never having to get all the way up to the 5/16" drill bit the Kohler mfr's official seat bolt anchor replacement video recommends. Use cobalt drill bits. Once the anchor was loosened from drilling on it, I pushed it down and it fell away.
how did you "pull" the anchor out?
did you have to use a drill again?
Thanks. You save ours headache. I have same problem and have same toilet and it is 20+ years old.
I am buying what he says to get, not the part from kohler. wish me luck. almost threw out my back trying to get the old bolts off. thank god for this video. thank you!!!!!!
Sorry to hear about your back, but I feel your pain! Let me know how it works out!
@@davidcomora the new bolts worked just like you said. only I am an idiot. I got one in and the other didn't catch. the rubber looked like it fell off into the toilet after turning it forever. I ordered more. when the new ones came, I realized that the old bolt had just shriveled up when I turned it and had not broken. I used the old one and have spare bolts now.
With the Kohler one piece toilet you have to remove the tank cover and reach inside under the lip where the bolts are supposed to be and unscrew them. I just changed seats on my Dad's and it was a bit of a headache but he LOVES that Kohler 1 piece. I made sure to use the metal washers on top but bought 4 ⅛" rubber washers, 2 lock washers and 2 nuts from the hardware store. I placed 2 rubber washers on top and 2 on the bottom with the lock washers and nuts and tightened them up with no problem.
Thanks for the video - when I called Kohler theysaid buy the removal kit for $34.95 on Amazon. This toilet has been a nightmare ever since the first one lasted only 2 yrs since the no longer had parts for the supeflush unit in it; had to get new toilet. Kohler terrible on service. I also bought a Bemis as replacement since I refuse to pay $190.00 for Kohler replacement seat to match my one piece-price gouging!! Since I am eldery lady with none ofthese tools gues I have to cal plumber to replace my toilet seat
Same issues with one I have in the house I bought in 2019. Thought it was an isolated incident. Trying to change seat now. What a pain.
Thank you so much!! We are having the exact same issue with our toilet.
Yup went thru the same thing on my one piece Kohler toilet. Went to Home Depot and purchased the expansion nuts you recommended ( a BIG lifesaver) and had the seat installed in 3 hours included removing the old seat. As you said it was the toilet from hell 😳
I just brought one it’s going back !!!! Thanks
Thank you so much for making this video! Very helpful!!!
I am stuck with one in my parents’ bathroom upstairs and I can’t twist the screw-wing-twist thing out since the hole is like half an inch in diameter or something like that. Thanks David for the help! I can try some of these suggestions. I couldn’t seem to find a video about this particular horrendous toilet model and how to deal with it and it’s half an inch or so sized hole where it’s so hard to take the screw out. 🙂↕️😅
Why on Earth would Kohler make such a badly designed toilet in which you have so much trouble changing a seat??? 😒😤
I just bought one, and they changed the design so the seat bolts go all the way through the porcelain. Thumb screw on nuts hold it in place, very simple...
THANK GOD FOR YOU!!!
I have the same issue.
Thank you for this. I had to use a wall anchor in the hole but it’s not very solid. I will try and find the parts that you used.
I just used an expanding rubber anchor from ace hardware. The seat was still a little loose because I should have bought larger anchors but I used contact cement to keep them from moving. The anchors and screws cost about $5.
I went through this like you did (seat kept coming loose) but the problem is that the rubber covered "well nut" or "cavity bolt" which is the next size up is too big. Lowe's had them all on display. Can't get it in the hole to even start screwing the bolt in. I got one of the Kohler metal anchors (they're now on Amazon) and was able to install it by pushing down on the screw when I fastened the seat. And I didn't need that overpriced tool kit Kohler tries to sell you for installing it.
I am stuck with one and thank you for saving me a agrivation. The one I have has a 3/8" and a 1/2" hole Very weird. Thank you
I repair these a lot. Trick is getting old bolts out and not over tightening new inserts. Unless your very handy call a plumber, retail for the kit is 30 bucks and I normally charge 150 in labor. Remember folks it's not what ya do it's what ya know.
Wish I knew you before I stumbled into this mess!
Nice, been struggling with the wrong hardware delived for a week now. You got it, kicked that toilets ass! #10-32 x 1-1/16 in. Brass Expansion Nut Model #814368 does it and it suggests the correct stainless screws when ya add em to the cart. Thanks man!
Was looking to replace mine with a new soft-close seat as the old one is starting to look gross. Glad I came here first. I'll either be prepared for the battle or maybe I'll just live with that seat! Disappointing for a "premium" toilet.
I have a K3402PB one piece from 1988. The bolts/nuts are accessible inside the tank
Basic issue is that installers don’t use anti seize on the bolts. If you don’t, you will face what this video depicts. This video is great for all the steps you should not take.
I replaced my anchors with genuine Kholer ones 3 years ago and when I did I put tons of anti-seize, but the anchors still stripped out while I was unscrewing them to replace my seat today. I think these Kohler anchors are just a terrible design.
A second issue is mixing two metals, brass and stainless steel in a wet environment and not expecting them to corrode into each other resulting in a solid mass of screw/anchor that either spins in the porcelain hole or is frozen in place. I’m thinking of getting a brass screw to replace the stainless steel one in the 84999 parts kit.
This toilet came with my place, I was going to replace my toilet seat bc it wasn’t soft close. Noticed I couldn’t get the screws out but after seeing this I think I’m just going to live with it. What a nightmare.
Isn't there a toggle type fitting that would work? Also, of course one would use stainless replacement . The original bolts are stainless and thus impervious to a regular hack saw blade. I got the hold fittings out through a few ingenious maneuvers and while the seat was off it was easier to hoist the one piece Kohler with my home made toilet "transporter" which all plumber already have-of course in professional form.
So you couldn’t screw the bolt from underneath inside the tank? I stuck a stick through the hole and it went through inside the tank. I’m not looking forward to it but I’m going to try putting my hand inside the tank to tighten the bolts.
How did it work out?
thanks for making this video, this is really really helpful
DO NOT HAMMER the grommet through the hole. You could crack the toilet. Bend the metal grommet with pliers.
I bought a new one 2022 and the seat screws in from the bottom like the other toilet’s. Apparently Kohler got the message to change it.
Wow, that's great news!!!
Omg, I reenacted almost every scenario last year
be sure to use anti See's compound so the nut will not rust to the mounting hardware.
I bought the metal Kohler kit and it worked ok to put a new seat on. But now about 3 years later we want to change seats again. The anchors are just spinning. I can’t pry them out. The ‘wrench’ they included with the kit can’t get enough grip on the anchor to hold it while I break the screws loose. They must have corroded together. I hate this toilet so much. Thought my issues would be solved forever by buying the official kohler anchors.
I might try slide hammering the screws and anchors out. If the toilet breaks, I will celebrate as I throw it to the curb.
THANK YOU!!!!!!!!
Yep, almost got a divorce working with my husband to replace a toilet seat on a Kohler one piece. Never again!
OMG, what a nightmare! It's a miracle the ceramic didn't crack while you were drilling out those bolts or installing the new anchor. Congratulations on your tenacity in getting it fixed. Were you able to remove those little scratches around the left anchor?
No, But we finally did get rid of the calcium buildup that was impossible to remove. I tried everything, then Mary came home with this pomice stone on a stick thing. I laughed it, knowing how much time and elbow grease I put into trying to remove the stains. Lo and behold, the thing worked. My mom just bought one and it worked for her as well. I think they are about $5 on Amazon. Vince, be honest with me, is my life revolving too much around my toilet?
What model Bemis seat did you buy? Great video. Exactly what we have been going through! Thanks.
Sorry, I don't know the model, but it was a standard Bemis from Home Depot that had the correct shape for the toilet.
I have exactly the same problem as you. I bought a Bemis replacement toilet seat thinking that it should be an easy install. Wrong, as you point out. I could not get the screws out that hold the old seat in place. In watching your video you talk about a Bemis kit that allows you to use the Bemis seat on the Kohler toilet after replacing the Kohler anchors. It looks like the kit is Bemis part HK36 (as shown in your video). I can't find it anywhere. Where did you get yours? If I can't find the kit I'm going to just replace the toilet with another and it won't be a Kohler one piece! Thanks for your video. It really helps.
Last time we needed a new toilet seat from hell, it cost us a $150 plumber housecall. So I figured to do it myself this time… carefully remove the existing bolts from the anchor… slap on a new seat and reinstall the bolts. Well, the first bolt came out. The second bolt is not coming loose, so I soaked it in KROIL… will try again in the morning. Then I took a photo of the model number on the inside of the tank and sent it to Kohler. They said the number doesn’t match with anything. Great. It’s a chinese Kohler, so. NEXT MORNING..Thanks to KROIL, a good screwdriver and a pair of old (USA Made) Vice Grips… I got the other bolt out.
Omg this is my life right now. Also Kohler toilet seat, trying to replace the seat 😭😭 will never buy a toilet like this again
Same situation...i hate it! When I bought this house it has two. The seats are in very rough condition and I want to install a bidet seat on both!
Hope you worked this out!
@@davidcomora thank you I did, in the future now can change in ten minutes flat, but getting the anchor bolts out was a drudgery!
Thank you - equally frustrated with my kohler one piece toilet. Ridiculous.
way to go and persevere. happy flushing
Dude. Life saver. This dumb toilet had me flummoxed. Thank you!!
Great value. Great looks.
Wow, another Bot post from Kohler to try to minimize this video. As I posted on the bot post below, I am about to change the flapper for about the 10th time since I bought this nightmare toilet. It is not an easy task, as it is difficult to remove the old black plastic flapper bar. I may post another video on that process.
thanks for the how to! going to tackle this project this week. Question- what bemis toilet seat cover is shown in the video?
link?
thanks!
Sorry, hope you sorted this out. I just picked up a standard Bemis seat at Home Depot that had the appropriate shape.
FYI: Call Kohler and you should be able to get the kit. I wonder if they have done anything to correct this problem? Mines 18 years old and while I did get the kit from them for free i never did use it as we were afriad it would crack and were not paying someone 150 to do this. Frankly, I cant believe a company of there size and supposed experience made this mistake or am I missing something.
I thought I might have had a lemon, until I posted this video and saw all of the other folks who had the same issue! I actually got the kit and one of the anchors broke and kept turning after I installed.
At 10.03 the fun continues i laught so hardq but felt your pain.. im going threw it now thanks for the info.. kohler from hell!😂😂
Hope you figured it out!
@davidcomora yes I got the screw spinning and loose then i lifted it about 1/4 high,.I put a glove to protect the porcelain from the steel hammer on toilet and the back of the hammer threw the screw. then I hit the steel hammer with plastic mallet it will raise it for me as I hit the steel hammer with the mallet.. so the steal hammer prys it up as I hit it with mallet.. it came off easy I struggled to use the recommended tools by kohler.. they weren't rigid, they were bending too much.. I used the steel hammer as a pry bar it worked flawlessly if u hit it with plastic mallet.. thank you for your help it took 2 weeks to go back was done in a 1 hr
Get the correct flappers, and replace the seat, I have been running Kohler 1 pc 2 of them for almost 20 years, no such issues...Ya replace the flapper maybe every 4 years, and the actual valve after 15 years!
LOL, I may make another video on how to remove the black plastic flapper bar from the back of the water tower. No easy feat! I noticed on Kohler's video that they cut at that point and then the video continues after the bar has been removed. I also notice they removed the ability to comment from that video as I suspect a lot of folks have been having difficulty removing the bar. I am about to replace my 10th flapper in about 18 years. Maybe my water is hard, but the other non-kohler toilets in my house have only had flappers replaced about 1 x in the same time period. This is not a cheap date!
@@davidcomora I use Fluidmaster or Korky brand or Kohler OEM flappers...I suspect Kory and or fluidmaster actually makes them anyway. The water tower with the snap in flapper in the back, ya have to make sure you have it proper height, otherwise doesn't work properly. Ya just stretch the thin part that goes into the holder, it snaps right in place...Water quality has a big influence on the flapper and the base it seals against last, for sure. I replaced my one Kohler seat with a new Kohler, using the tool kits from Kohler, inserts went rigth in, now I have a new seat that closes on it's own slow like, no more dropping it. the installation kit from Kohler makes it easy
Thank you
We rented a home with one of these pos. The lid looked so bad, like someonehad some major gangly piercings down yonder. Back to the lid, you have to give the anchors to the toilet gods, and drop them in the base. The new seat has anchors and if the seat needs replaced, repeat. This is a money maker for sure for them. Super nice shitter however.
I finally thought I found the hardware at Home Depot online.... but the parts never arrived. I'm having Hell trying to find those expansion nuts or bults and screws. Have you maybe 2 to spare? Can I buy them from you? I am at a loss. No way to fix my toilet lid... The "original parts" for Kohler's one-piece toilet didn't fit my holes at all. My holed are 1 cm in diameter.
I hope you were able to find them. Have you tried Lowes or Ace Hardware?
@@davidcomora No, I’ve tried everything and every instance, including Amazon and EBay
After you cut the head of the bolt off, what do you do with the shaft and anchor still remaining in the toilet???
@@ienjoyrice let it fall into the fixture.
How about pulling the lid off and reaching inside the tank to grab the nuts? Took me about 2 minutes.
@@richarddickin2218 Glad to hear this worked for you. Sadly, this was not possi ke with the heavily corroded pieces most of us have to deal with.
Omg. Listen to this guy. DON’T BUY THIS TOILET!!! My parents have one. It’s probably 15 years old. The flushing design sucks. You have to either hold the handle down, or flush it firmly enough so the flapper stays open long enough to flush. I shouldn’t have to put how to flush instructions on the toilet. And this GD nightmare of changing the toilet seat! The expansion nuts seem to work very well. But whoever the genius is that designed the “quick release” toilet seat is an idiot. As soon as you tighten the bolts down, the quick release bracket spreads out so that it doesn’t hold it in place. Why does anyone need a quick release toilet anyway??? I’m ready to rip this toilet out and explode it! Rant over. Thanks for the video. It definitely helped. Sorry to you and probably the rest of the people here that are stuck with this toilet
Yeah and they're extremely expensive new. Good luck
Did you see the 84999 Anchor set with the remoal tools?
I bought a kit from Kohler, not sure of the model, but the expansion screws broke upon installation. So the rubber expansion screws were a lifesaver. Is there new kit?
Great video. But where did you buy the plastic adapter rings?
I had the same problem 😤😡😤😡😤😡
Supposed to also have a lock washer with the anchor kit
You missed a step on the anchor inserts. First tighten with lock and flat washers and then just the locking washer. If you overtighten the anchors they will break! VERY BAD IDEA TO REPLACE THE ANCHORS WITH CHEAP ONES!! You will never get them out and they will spin like hell when you try to drill them out.
Tought to determine what is "over tightening" the rubber expansion screws have worked like a dream.
Believe it or not, I'm still at it. It has been almost 2 months. Could you, please, answer me this? The anchors contained in the 84999 seemed too narrow for the holes in my toilet, a Kohler Rialto, in spite that they recommend this part to fix my toilet seat. Is it maybe so that it doesn' t matter, since the expansion nut will expand anyway? I can't find any of the other nuts and screws that you and some other people talk about. It seems that Home Depot is no restocking a lot of things, maybe because there are problems with the supply chain. At least in Miami.
Ugggh....as I recall, i had a tough time getting the Kohler expansion screws in place, they seemed tight and then 1 broke. Mine were really tough to get in the holes. I had to bang them in and was afraid I would crack the toilet. I found the Home Depot rubber expansion screws worked great, but they need to be the appropriate size. They are pretty cheap, so maybe try a couple of sizes.
Thanks !
Unfortunately, I didint watch oyur video to the very end, when you tell that Kohler's parts are not worth it. So I ordered the kit from Amazon, just to find that the anchors were loose inside my holes: they are 6 mm in diameter and my holes are 9 mms. Now, I have been trying to find your Expansion Nuts #10-31, 1 1/16 in Miami and I cant find them. Neither in Home Depot, Ace Hardware or Ster Brothers. Can yu give me a hit as to where to find the hardware you are showing in your video, both the but and the screws? I'll be most thankful.
Im about to get crazy trying to solve this!!! A toilet from Hell, indeed.
@@viviangude2789 sorry to hear about your troubles. I did find the anchor kits at my Home Depot.
Great Video , my folks have this same toilet set up and problem.
Does anybody else feel like they're listening to Jimmy Kimmel.??? Just saying.
Can you find the toilet seat adapter at Home Depot?
Why dit you not just change the toilet? I just run into the same problem and for the price of toilets and labor involved to get this done I’m thinking better to go for other options and change
I guess I have too much time on my hands! I accepted this as a challenge.
What toilet seat did you use? We’ve got the same stupid toilet and finding a seat that works has been a nightmare.
I bought a standard Bemis and then had to pick up the adaptors that I demonstrate to get it to work. Once I figured it out, all has been well...though I dread the thought of replacing the seat in the future.
I had this toilet. Its crap. The instructions say you have to buy their removal kit, which is pretty much the same as a crowbar to remove the Anchors
Yes, i started with their removal kit and then one of the new replacement anchors broke and kept spinning...
I bought a house with one of those and it has been nothing but problems too - multiple flappers and constantly leaking - now I'm having the seat issue! Worst toilet ever made!
Good luck with it! I still have mine and I just know that I will have to replace the flapper every couple of years. I hope the toilet seat outlives me, as I never want to go through that again!
May I ask where you got the adaption kit?
Is this a Rosario model 3434BB? The model number is printed inside the tank.
I believe the model number is 81818AA
My one piece has plastic thumb screws that are accessible. Must be an older model.
You have a much better model than I have!
@@davidcomora kohler must have realized the stupidity of the past design lol. I still can’t believe it.
I hate this toilet!! Been going on for over a week trying to replace the toilet seat.
Boy! Do I "feel ya" LOL
To change toilet seat, you'd have be firstly a contortionist, secondly, you'd need extra hand, then you'd need an adjustable wrench to place under and behind the one piece toilet tank to snag-on the bolts AND simultaneously hold a screwdriver to hold the top screws and THEN...you're good to go.
My solution: buy another toilet. This is what I'm going to do this week.
We have Pfister with the same issue. I managed to change the seat once but it keeps on coming loose.
Whoever designed this shitty crap (no pun intended) ought to be horse whipped and pissed on!
It looks good but that's about it! Useless otherwise.
P.S. Might have to break the whole damn thing because can't find WHAT is actually holding the damn thing to the floor. Grrrrr....
Thanks for you comment and the laughs! Glad to know I'm not alone! My wife and my kids (who have grown up with me cursing out this toilet) have been on my case to throw this thing out for years, but I'm stubborn and I've taken on "the Kohler Challenge" as my life's work! Pretty pathetic! So, I finally got the seat back on, but I still need to hold the handle down for the entire flush cycle or I don't get a good flush. I know if I spent 20 minutes adjusting the internal hardware again, I can fix that issue as well.
@@davidcomora Your welcome. I was giggling to my self watching you, LOL
But what a "challenge"... Funny, I have issue with the flusher too. And ...the damn thing whistles too!?
Worse when guests have to use it as they don't remember having to hold the frigging button down till the "surprise" is gone. Guess who has the shitty job of keeping an eye on it ....? (Taped sign onto the wall doesn't help).
"No shit" has a new meaning...LOL
I'm with your wife and the kids! The must love you to pieces to put up with it LOL.
Get rid of it :-)
Thanks :-)
@@davidcomora I just shortened the travel on the chain attached to the flush handle i.e. holds the flap wider open. It seems to be working.
Imma alone my father, RIP got these awful toilets installed in his house . My toilet seat broke I ordered a new on Amazon Ive replaced many a toilets in my day as a woman but now that I’m almost 60 now and caring for my mom with dementia I’ve had a Stroke we are alone have a home warranty even though my folks have owned this house since New over 25 years ago. I’ve unfortunately threw away the broken toilet 🚽 seat ordered a New one and guess What? One of the Bolts won’t Budge…
What to do I think after sitting on a toilet with out a seat for several weeks now plus it’s So Low hard for me to get on and back up. I think I’ll call my Warranty and replace to a American Standard and be done with this Nightmare. Every Upgrade on this house my dad had extravagant taste he had a Japanese Soaking Tub put in the Big Master Suite . They had to use a Crane and knock part of the Wall out. To even use it is Quite almost impossible and Dangerous. There’s Slick Marble all about with steps to get in not enough flat space you Practically need to be a Contortionist or a member of Circus 🤡 De-Soleil in order to enjoy 😱❗️
Thank you for Sharing ❤️
Was looking for new Koholer seat and wound up here. I have to say LMAO pun intended. I have a Kohler Rialto toilet installed by plumber which worked fine for about 6 months after that it became a Ford (Fix Or Repair Daily) toilet. After 6 months it began running continuously and required adjustment almost daily until adjustment used up and had to buy new flush valve assy and then another. By 3rd time learned there was a repair kit and went to plumbing installer with kit number and he plops down the entire assy again. I guess the parts guy thinks everybody except plumbers are stupid, he's quite the sales man or so he thinks. $60 assy vs. $12 kit, hum let me think? Found a work around for the never ending running toilet by using the standard wall valve. By the time was about to buy 3rd std. wall valve bought a ball valve type instead. Had a grey Kohler toilet seat which with age has now turned about the color of your seat/lid. This has been going on for 40 years LOL. Will chek out that Bemis seat. Thanks for sharing.
What did you use to drill out the headless bolt? I am presently at that stage lol
Once the head of the bolt was sawed off, I used a steel rated drill bit that was smaller in width than the bolt and drill down in it about a 1/4 of an inch. Then I used an old drill bit and a hammer to push the bolt down into the fixture. Since you are dealing with ceramics, you need to be careful when you pound down... so if you need to drill further to make the bolt pliable enough to pound through, it might be a good idea.
It’s truly is … I have had the hinge replaced twice now I can’t get the knobs
Overpriced over rated!
Ive got the same shit going on with my new seat. Fkn ridiculous.
Thank you very much for the replacement instruction. But I don’t know why designer designed such a SH.T.
Wonder what f-ing genius at Kohler designed this type of toilet-seat arrangement! What was wrong with a simple screw mount on the outside?