How To Install Ceiling Drywall Using A Drywall Lift
Вставка
- Опубліковано 26 лис 2024
- I this video I will show you how to install ceiling drywall using a drywall lift. I go over the parts of a drywall lift. Some people call a drywall lift a panel lift or panel hoist. I also show you how to cut drywall using an utility knife and T-Square.
🔴Subscribe for more home building tips to save a TON of money here: ua-cam.com/users/the...
🔵Product affiliate links: (DISCLAIMER- I am an affiliate with the companies of the products listed below. I get a small commission that help support the channel at no extra cost to you)
Ridgid Tool Combo Kit: tinyurl.com/1v2n6gyj
LIMITED TIME: Get FREE STOCKS ON WEBULL when you deposit $100 (Valued up to $1600) act.webull.com...
⏱TIMESTAMPS⏱
0:00 Intro
Disclaimer: This video is all based on my personal opinion and is for entertainment purposes ONLY. I am not a financial advisor, CPA, attorney, tax advisor, electrician, plumber, housing contractor, designer, or any type of profession to give advice. I am just a consumer sharing my experiences and research. If you do need knowledge for those types of things, I will advise you to seek help for those professionals. .
🟡 Check out my Amazon store! 👉 www.amazon.com... . Here you will find tools and supplies used in my videos. (DISCLAIMER- I am an Amazon affiliate. I get a small commission that help support the channel at no extra cost to you)
🔴 Subscribe for more home building tips to save a TON of money here:
ua-cam.com/users/the...
Disclaimer: This video is all based on my personal opinion and is for entertainment purposes ONLY. I am not a financial advisor, CPA, attorney, tax advisor, electrician, plumber, housing contractor, designer, or any type of profession to give advice. I am just a consumer sharing my experiences and research. If you do need knowledge for those types of things, I will advise you to seek help for those professionals.
Awesome job explaining the needed steps with drywall and lifter for a DIY guy to carry on with the project. Thank you.
My lift has these pieces of red rubber covering the arm ends. (Yours looks black) They grip the board so it doesn’t slide off of the lift. Before you start to go up to ceiling, rotate the arm hooks down out of the way so you can go right up and tight to the previous sheets. It’ll save you a little time messing around getting the sheets in position. You can do this from floor before you start cranking it up.Great videos! Hope this tip helps!
What lift model do you have?
@@anthonycampanello265 it is a Panellift drywall hoist. Yellow color and goes 11’ without extension. Bought it about 15-20 years ago and still use it from time to time. Definitely worth using if you gotta do ceilings by yourself. I’ll be using it next week! 5/8” Drywall on ceiling!
When using a panel lift, If you start at the peak and work your way down you won’t fight with the hooks on the lift.
I know this is like a do it your self type of video and to a very beginner level I do this for a living my self and the one thing I'll give you props on is the fact that you used glue on the ceiling I was wondering about this lift for when I work alone nice video sir
Thanks a lot Henry! Drywaller’s are amazing people. Thank you for what you do!
@@TheExcellentLaborer not everyone appreciate it but a job well done comes a long way every time I work in a home I always ask if they want us to use glue on ceilings because it's better some say no but as a professional you're suppose to tell the owners why it's important to do it
I always hit the like button to pay for these videos from him.
thanks for showing the right way to do drywall. So many people here on youtube omit the glueing, which to me is the most important. That is why I sub to your channel, right and to the point. I would like to see your builds become more technical and use better building practices for more of an energy efficency standpoint. For example, I see the traditional bat insulation. I would sprayfoam the roof deck, then get aero barrier to make the seal, followed by the final layer of rock wool. I do like your videos and especially found a tremendous help on your electric series. Thanks
I see windows and some doors installed. Congratulations! Since you are installing drywall, I wonder if you are going to make a video on what is going behind drywall, like insulation, wiring, and plumbing. Thanks for all teaching you do on this channel.
This video was made at my dads house. The house I’m working on I will Be showing everything from plumbing to electrical. Thanks for watching! Stay tuned
You can also use hot mud if you don't have drywall adhesive. Normal practice in many countries , in uk it's called Dot n dab,once it sets its like sh 1 t on a sheet . Hope it helps
Never saw that!! Amazing install results!! VERY DETAILED!
Thanks a lot man! It does take a little longer with the lift but safer!
on a vaulted ceiling you actually want to do the top row first, get your peak nice and tight. its alot easier to cinch the sheets upwards, then the hooks wont be in the way.
You have a great utube channel. And the one that will definitely go tooo for more information.
I appreciate that, Steve! Whenever I build a house, I try to record everything I’m doing. Stay tuned for more footage to come!
Buying a lift was the best money I ever spent
Thanks Josh.
Sure thing Amazing Framer!
I've never heard of drywall glue before that ! I've always used clout nails.
Thanks ! Can you move those extensions to other arms . I’m going to be hanging a sloped ceiling in vertical position because of the under strapping
Can you install the drywall vertically instead of horizontal with that lift on an inclined ceiling? Thanks mate😊👍
Wooooow an American used glue on gyprock , nice man , never seen you guys use glue, we use it on all gyprock in Australia
In America gluing drywall is common practice. I have seen some people just put screws on the edges of drywall and just one in the very center on the walls and the glue does the rest of work. We do not do it like that but some do. It’s interesting how Australia in America is so different with building. Thanks for the comment!
@@TheExcellentLaborer never once on any channel have I seen guys use glue in America but see Americans comment on as to why we use glue haha
I live in the Midwest USA. Edwardsville, IL.
The only pace I’ve seen glue on drywall is on UA-cam outside of the USA.
The Excellent Laborer does it, I wonder what part of the country he is in?
Also I’ve seen the glue dabbled on (blue)with a wide puffy knife in the UK
You are a good teacher it is pleasure to watch your videos your speed and explanations are on the point.
Can u do a video on backing or floating backing of where it goes for drywall please. Also I'm having trouble with an addition where the existing wall is ready to come down but want to reassure that I'm not missing anything out before i take it down. Would appreciate your feedback soon. Great videos & stay safe from AZ.
I have a question! Do they have to be laid out like the floors? One whole sheet and then half one?
nice! can you put a link to the screw holder used on the power drill? also what length drywall screws are you using?
Ive never seen anyone use drywall glue before , how would this help if you have vapor barrier?
What glue adhesive do you recommend? Any construction adhesive will do?
Great presentation- but man I hate those dimple bits. They always crush the drywall in a perfect circle, rendering the strength of the paper/gyp useless. You’re using glue, so I’m sure it’ll be fine, but without glue those screws would most certainly pop over time. For this job a gun and collated attachment would have paid for itself. Also, all the rental yards around us prorate hourly. No more free Sunday’s 😔. Don’t mean to be over critical- keep doing your thing. I’ll throw a like and sub!
Yes the dimple bits are not the best. Glue and screw is the way to go! I appreciate the like and subscribing! Stay tuned!
What's your opinion on removing popcorn-coated drywall from a vaulted ceiling and installing new drywall instead of scraping popcorn off? The drywall is attached directly to the bottom side of the roof. There is no attic space. Also, years ago, a new roof was put on top of the old roof. Now the second roof is old and needs to be replaced. Since the outer-exposed roof needs to come off, I feel it makes sense to also remove the original roof underneath. If both come off, chances are some lumber may need to be replaced. If that's the case, is it best to also just remove the original popcorn ceiling and drywall together and reinstall new drywall? The original drywall ceiling is also cracking at the seams. Seems easier to remove and replace drywall than spending days scraping and ending up with old drywall full of scrape marks. The popcorn is also coated with acrylic paint which makes scraping harder. Are there other things I need to take into consideration? Your opinion is appreciated. Good video. I gave it a thumbs up.
Get new roof done first, the remove old popcorn drywall and glue and screw new stuff. 5/8 if 24in oc.
Any luck using this to hand hardie board (4x8)?
Thanks for showing Ontario Canada
How did you close off the corners with the drywall
Appreciate the help man
You got it!
Can a guy get away with 1/4 in drywall in a garage to stud or will it sag too much?
Can drywall be butted tight or do you need to leave a gap between sheets for expansion?
Drywall should be butted.
You can research these things on your own instead of expecting people to work for you.
This video is part of my research. Why would you be watching it if you knew how to do it? So you can write ignorant replies calling answering a question working for someone?
Your the most slowest drywaller 20 minutes on one sheet we usually take 2-3
You guys install the drywall directly to the truss with no strapping?
Yes. Every contractor I knew does that. Thanks for watching!
@@TheExcellentLaborer You need a vapor barrier sheet tacked to the truss and then some strapping in opposite direction at 16inch and then the drywall...
Dude was cold shooting this video he got a hoodie underneath his carhartt
I am grateful for your excellent work. Very detailed. Thank you. Keep going.
Many thanks!
Thanks!
No problem Jessie!
What about sheet cut in half? 24 inches
Good video and explanation. The only fault I can see is that it looked like you were installing 1/2" drywall, 1/2" drywall on the ceiling has a tendency to sag between the joist when there 24" on center, if there 16" on center you can get away with 1/2", but you should be using 5/8" on the ceiling.
Hi there The Excellent Laborer, thanks for the video. Really appreciate you showing us how to use the drywall lift. I had two questions: 1) you mentioned that one should always use drywall adhesive. Did you mean that it must be used for ceilings or for both ceilings and walls? Also, I have seen some people install it without adhesive--does the adhesive prevent popouts or shifting? 2) At the very top of the ceiling at the ridge, did you cut two separate pieces of drywall (one for each side) or did you cut one piece, score it on one side and NOT cut the paper on the opposite end so that it sort of naturally hinges? Is one way better than the other? Thanks for the tip about renting over the weekend--I don't think Home Depot does that though. All the best, H.D.H. [: { ].
Yes you should always use drywall adhesive on the walls and the ceiling. Gluing and screwing is the best method to prevent drywall cracks and pops in the future. The top of the ceiling is best to do that method that you mention. We actually just did two separate pieces and the finisher uses a special tape for that peak.
@@TheExcellentLaborer Thanks man for the reply. All the best to you. H.D.H.
Gentlemen might you know the name of that hoist ( or brand )I’m doing a living ceiling all by myself ( @ demo stage now) buy a hoist from harbor freight seem ok for the having tools aspect but I think that a steady hoist would help out a solo job the most. P.s rent it on the weekends if possible right? Thank you 🙏
Using the drywall glue is a good thing specially on ceilings because it prevents vibration from loosening the screws and cracks over time and yes you'll see a few people not using it because they either want to be cheap and/or lazy or they are used to the old school methods I've seen people still using nails on drywall I consider this a huge mistake
Thanks for the video.
Awesome video
Thank you....
No problem!
Like a pro!!
I say more like an excellent laborer! Thanks man!
If you move to Northern California ill give you a Job!
I appreciate the offer, but I like the area where I live. Thank you!
What ceiling height you got in the attic with the 7/12 roof pitch ?
This is my dad’s house we are working on. His roof is a 6/12 I believe. The vaulted ceiling you see here is a 3/12I believe. Thanks for watching!
@@TheExcellentLaborer is there enough attic space for storage on 6/12 pitch ?
It depends on how wide your house is. For example, if you have a 6/12 roof pitch and your house is 24 foot wide, that would give you a 6 foot high center in the attic. So a lot depends on how wide your house is.
@@TheExcellentLaborer thanks. So 5/12 pitch on a 50' wide house should give you about 10' clearance in attic height ?
Yes correct!
absolutely superb job and demo explanation ... and nice to see you have someone in the medical field standing around ... how much does that cost? XD
The wife does help keep me healthy with her medical experience. She is a keeper!
A tip: watch series on kaldrostream. Been using them for watching loads of movies during the lockdown.
@Lorenzo Andrew definitely, I have been using kaldroStream for since december myself :D
@Lorenzo Andrew definitely, I have been using kaldrostream for months myself :D
Nice work
Thanks man! Thanks for watching!!
Does anybody have a trick how to get it up there without having to dead lift the whole thing, especially if using a 4 x 8 of 5/8 inch drywall ?
You cant... There are drywall lift who can get lower as 3 feet from the ground but from ground to the lift you need to lift the sheet to place it... But it's already better to dead lift and hold it at 12 feet high
Thanks John !!
I actually figured it out....
Rather difficult to describe, but definitely was effective.
Cheers
Good video
Thanks! I appreciate you watching!!
I've never seen anyone use glue on drywall. I've been building houses for a long time.
Super.
Thank you! Cheers!
So cute!
Thanks
Hey mate why don’t u just set up on a tripod if ya wanna make longer videos and just talk to us when ya wanna explain things, longer videos =more ads which means more money in your pocket to reward ya for your time and effort producing these videos..... in saying that they’re already good length videos just will be more content to release
I know exactly what you’re saying. I feel like it people may get bored just watching me work and not talking. I feel like if I cut out the boring stuff and have almost all talking people stick around longer. I could experiment with that idea. That’s definitely good thinking. Do you know what I’m saying though?
@@TheExcellentLaborer yea I get ya , like for example you could have the camera rolling while loading the sheets and installing them and then talk every now and then about the process , it’s just an idea for more content and make a series out of some of the jobs you do
Are ya cold?
Glue is not required in Ontario Canada, and generally only amateurs/handymen use those countersinking bits for the screws. In new construction here, the drywall crew tacks the boards in place with nails and then the screw guys come through and fasten everything securely before the tapers can put the mud on. You’ll be cursing whoever put glue on the back of your drywall if you ever need to change it or make a repair in the future. 👎
Agree, never seen anyone use glue here in manitoba. I do like those bits though. I don't do enough drywall to buy a dedicated drill. Small jobs big $$$
I think glue is appropriate for a ceiling but I do agree with you, glue on the walls may be overkill and a hassle down the line. Here in Alberta glue is used for ceilings/walls although there are folks who equally don’t glue the boards. I suppose you could apply dabs of glue for extra security rather than a complete bead along the stud. If the screws are embedded correctly and the right amount screwed into the drywall, the board shouldn’t be peeling away from the wall…..
I see that in New Zealand only glue is applied with a screw used simply to keep it in place until the glue sets up.
This is agreat video
Thank you Robert!
💯👍👍
Tapers hate you for using impacts and dimplers. Buy a proper drywall gun
Too slow, 15 minutes for hang one sheet is too long 😴😪😫😑
This is an explanation video not a speedrun test 😑
@@deLAchrys9 rookie
stupid tu use glue on drywall
It is common practice to use adhesive