You saved me so much time, money and frustrations. Fixed a 18ft tall 40x30 sagging ceiling. Scraped 4x as much painted popcorn ceilings. Countless nail pops. 10 peaked sheets. Covered textured walls with skim coats. Replaced a 4x3 section of ceiling. Numerous failed tapes and cracks. and everything is PERFECT. Took me 80hrs lol but I'm happy. THANK YOU!!!!!!!!!!! BTW Wet sanding with a microfiber backed sponge in a circular motion THEN sanding gave me a level 5 finish.
Awesome! I’m so glad the videos helped. And thank so so much for the generous super thanks! Looks like I can support my luxurious coffee habit for one more month😂❤️
@@vancouvercarpenter you're welcome! I ruined the perfect walls and ceiling I created by not having enough pressure in the paint sprayer. So now I get to do it all again!!
I'm actually considering flat wallpapering the whole thing and skimming the joints. I just don't think I have it in me to skim and sand it again. Have you ever done this?
For those who don't understand why 1 1/4" is the right length for your drywall screws, that length is long enough to reliably grab the stud without hitting wires hiding behind. Electricians are required to have their wires deeper than 1 1/4" from the surface of the stud, so the thickness of your drywall is your safety cushion. On the rare occasion when they can't get wires deep enough, such as on a corner, they nail a plate to prevent misadventure. Buy the right length of screws and you won't likely burn your house down.
You are seriously the drywall whisperer. Time and again I watch your videos and walk way so much more informed than I ever anticipated and it’s saved me not only my initial questions, but future headaches as well.
I like that you don't edit out the parts that show you're not perfect even though you (definitely) are a pro. It gives us beginners more lee-way to not expect us to do things perfectly or without a hitch. There's a learning curve for beginners and they shouldn't judge themselves as lacking anything because of it. I also like reading the comments as the comments provide their own useful tips to be considered and additional insights. Your channel and fanbase is the best!💖
A drywaller with 15+ years experience here. I have a very similar set up belt, but I've got a trick for you to use if you'd like. Instead of keeping your measuring tape on the right pouch, keep it in the smallest end pocket on your left pouch. So when you need to take out your knife and tape to do the sliding technique, or tape and pencil to make a mark, you've got both ready to go at the same time. It saves about 3 seconds, but when you have to do that 200 - 300 times per day it adds up.
People think tradesmen are tradesmen because they aren't capable of thinking on the level of a doctor or lawyer but a good tradesman Is the master of critical thinking, thinking ahead and problem solving. That's why doctors and lawyers hire them to do things like this. If it was easy anyone could do it.
Always like and appreciate your videos. As a chick in a "man's" field, it's very helpful to have reinforcements when someone says, "why are you doing it like that?". Thank you. Keep in mind I live in the southern US where I'm not always taken seriously.
Yeah... Some of the old heads have some fragile egos. I don't have to deal with the sexism, but since I'm in my 30s, I frequently deal with the "I've been doing this since before you were born" attitude. Thankfully, a lot of those attitudes are aging out with the generations most responsible for them. It'll be our world soon enough :)
Also, after a little reflection, I should state that I didn't intend to make your post about me. There's enough dudes out here derailing the conversation in their favor, even if it comes with the best of intentions. We can all be a little more mindful sometimes :) Good luck out there, J!
I'd just be happy to have someone help me that is competent in drywall ... perhaps it would make up for my incompetence ... usually the mud man hates to finish drywall that I have installed ... and of course I am the mud man too.
Oddly this is the absolute most “How to hang dry wall” video I’ve found even if it wasn’t the way you intended to frame the video. Super helpful and I feel much more prepared to dry wall over the siding in my house now. Thanks a tonne!
Love watching your videos. I am doing a whole house renovation, and your videos have been a life saver. The first one I watched was on trimming out windows. Thanks to you, my windows look perfect. You are fun, entertaining, and informative. You aren't afraid to make a mistake. They become a learning experience for those of us out here who will make a ton of them. Thanks so much for your time and expertise.
Also thank you for your videos. I used so many of your videos to help me fix my walls cracking and destroyed corners, and several cracks. No experience and you were huge help. Husband is happy and was just expecting me to paint over cracks, he was quiet impressed I fixed the wall first.
I’ve drywalled a few rooms in my house, self taught. I learned so much from this video, wish I would’ve seen it before I did anything, would’ve saved me so much time!
Curtis Aitken, how’s the handyman business going? Asking because I pretty much hate my day job and have been thinking about starting a side handyman business and seeing how it grows. Not sure how it is in your neck of the woods but trying to get any professional in to do work they are either booked out 6 months or charging a heavy premium. If you don’t mind replying would really appreciate it.
@@72cgray I'm not a handyman but research the laws concerning handymen in the state you live in. Unless you have a contractor's license, there are many restrictions on what handymen can and cannot charge for jobs. In fact, my GF just took a handyman to court and won. The judge did mention that the handyman should've had a contractor's license because his rights are very limited as a handyman.
@@72cgray it depends on what state you are in. I am in SW Florida. In Florida I am not “allowed” to do any electrical. I am not “allowed” to do any plumbing behind the walls. The fact that I can depends on the client. I won’t do anything that puts my insurance at risk. The insurance is cheap, the license here is easy. I’ve just started about 2 months ago and it’s my full time. The hardest parts are figuring out what/how to bill your clients and learning to say no. I work in a very small geographic area. I’ve not had any days off I don’t want. Know your worth and be honest…you’ll go far. I charge $75 an hour and they buy all the items they need if they pick them up or pay me the $75 an hour to goto the store to pick them up. Be consistent, honest and the rest will come to you by word of mouth.
Man oh man. This Vancouver carpenter is so good at teaching techniques of carpentry with an easy going presence. There should be Oscar type awards for these helpful videos.
Just a tip for chalk line. Cut through the board with your knife quarter inch or so and throw the chalk line in the grove with the holder pulled out the back side. Works better that way and won't fall off. Also any extreme angles will become much easier.
I appreciate how you looked for space in the outlets without wires before you router the hole. As an electrician I can tell you that not all drywall guys worry about that. Have had to fix plenty of wires chewed up by routers over the years. Thanks for your attention to that detail!
As a drywaller for 15 years after being chewed out for chewing up wires like going in the box with the routers I made it a rule stay on the outside of the box by 1/8 of an inch plate covers it and you don't have an electrician all over your ass
On another thought I can tell how good the electrician is by if I measure from the floor up to the bottom of the box after a measure a dozen of them and they're all set it 15 or 16 in I figure I can trust them not be all over the place with their measurements
Good info… regarding setting the screw depth, I’d add that replacing the Phillips bits frequently helps. This as as the bit wears the depth the screw is sunk decreases. The wear occurs very little from screw to screw but after a 1,000 screws it’s noticeable. Don’t cheap out on changing blades and bits… they are consumables!
@@infotechsailor Mine... No! That was my point! On the other hand, I've seen guys with bits so rounded off that they had to put a lot of pressure on the driver to keep the bit engaged in the screw head... and they kept messing with the depth adjustment. That comment was for "those" guys. 😜
@@infotechsailor You need to buy better bits. You should be getting at least 100 screws per bit. Better yet, get Torx drywall screws and you will get even more out of the bit.
Drywall fast and cheap. But also fire resistant. I grew up in a house in California that had 1/4" Mahogany plywood for the walls. Ours was painted white but our neighbors was varnished. Their house caught fire and was gone in 15 minutes. Their garage didn't have the original Mahogany plywood and had been drywalled and was the only room left standing. The next week my father ripped our Mahogany out and replaced it with drywall. I had stucco concrete walls in one house designed as a passive solar experiment. The walls were done like a basement. It made the house very quiet as it blocked outside noise. But much harder to work with than timber frame and drywall. If you want wood or some other expensive material put drywall behind it. It may save you life.
and for the cost, drywall is very sound absorbent for those that don't know, gypsum isn't just non-flammable. because it's a hydrated mineral it outgasses water vapour when it gets hot
I found your 1- series of "every beginner Drywall Mistake I can think of" super usefull. As for the flow of the edited videos - GREAT. Did not impare the great info your shared!
Its a gift to know something well enough to find the confidence in competence to instruct others in it. I'm just fixing up my house and this was priceless! Gracias!
I made a small steel box that fits perfectly inside an outlet without wiring device (no gaps), mounted two neodymium magnets on top. Cover drywall without any cutting and then use another magnet to find the outlet behind. Then just router it, first inside (plate protects the wires), then fine perimeter cut to outside dimensions. Saves lots of time on measurements and alway perfect result. Just wanted to share, not sure if there are similar things out there on the market...
A type of your solution is standard in Sweden. But the inner casing of our electrical outlets are round. So you can use a hole saw on the drill and cut around the magnets. Even a beginner can get a good result within 30 seconds.
Never in my career as a sheet rocker have I ever heard someone say “unfortunatly we don't have any ceilings to hang” lol. I so much good info in your videos!
A little trick I use for outlet/switch boxes that I find really handy is i'll wet my fingers with water and put water on the box face (outlet/wires pushed inside box. You then put your sheet up against and give a few knocks where boxes are. When you pull the drywall back off wall you have a perfect outliine of where box is, then use a oscillating/router tool to cut it out.
I used to live in Vancouver and used to do renovations so did this a lot. Its been a hood handful of years though so its nice to get a refresher in. Also, the drill always found a way to embarrass me too when others would watch and commentate so I feel ya . Love the videos and look forward to continuing the journey
There is definitely a rhythm to hanging drywall. I do a lot of patchwork and these are helpful tips to remember! Now you have to do “Every mistake newbies make when taping!”
As a taper I feel obligated to say he should not do it becuse I have seen his taping videos and he doesn't know how to tape but I am glad he was taping to understand how to hang drywall. Just a shame no drywaller will watch this video and take notes. These are not newbie mistakes. Almost all drywallers make them because they don't have to fix their stuff. An example even he did a mistake that will cause nail pops. He doesn't know that because it was never his job to fix them and the mistake that will cause it isn't inexperienced screwing but he screwd top and bottom and then went in the middle. My english isn't good enough to explan it but the board could sliglty bend in the middle because of it and the screws will force the mid to get to the studs and eventually it would cause nail pops.
Good advice on setting cutting area up. One thing I do is put paper or plastic down in the cutting area. Once all the boards are cut fold up up and clean all the chunks up. In a Home Reno this saves on the mess.
Hi thanks for videos fun to watch! Just want to say that the "reason" for the crumbly drywall besides being fast and cheap is that it is very fire proof, and in fact if it gets hot it "bleeds" moisture! Sometimes in commercial buildings they require a "firewall" which means about 3 layers or more. In elevator shafts its 1 1/2 thick stuff only 2ft wide.....this is for fire protection and making sound proof too. We used to always go "to and through" light boxes, which means a number (AKA "give me some numnums bubba") for near edge, and a number for far edge, so if you are on ladder taking the numnums, you want to tell partner doing cuts on ground for example 32 to it, and 34 through it....and from the "ups" or "the buttedge" Also we didnt say "one and three quarters" or "two and three eigths" instead go by eighths of inch - for example one and three quarters would be: "one and six", and for two and three eights you would say "two and three" For a quarter inch or half inch, you can say "quarter " or "half" however......thats how we did it down in Seattle in the Carpenters Union work at least. Most of time two people, so lots of times one gives numbers, one does the cuts when doing ladder and scaffold work. Also in the nitty gritty numbers, you say "shy" or "strong" which means 1/16 to 1/8 less or more to the cut. We called the board lifter thing a "kicker" the hole cutter the "circle jerk" From Pink Floyd song to keep amused on job: "we dont need no insulation" and "we dont need no fire control" with british accent.... AjsoL "Ah love drahwall.... drahwall is mah life" with dumb hillbilly accent... "you only need to be a little bit smarter than the board you hang" a good motto Careful of stacking too many boards angled white side out on wall - as if it falls towards you you can break leg easy! That stuff is heavy. Great videos I had fun back in the days hanging sheetrock actually looking back at it. Mudding was always a mess! "dont worry the tapers will fix it!" and move on to next board....(sometimes paid by the sheet non-union work) Once we did a house that had no permit to an add-on, and the living room and bedrooms rested just on concrete blocks on top of dirt - no real foundation....we didnt know this, and cracks kept appearing everywhere because of the added weight of drywall on walls made it sink... it was total nightmare we had to go back and fix over and over...finally asked my old boss to take a look, he noticed the foundation nonexistent....so example of not being a bit smarter than the board you hang.
I have been watching a lot of your videos and the information is amazoning. I have learned a lot about DRYWALL from your videos and again i am amazoned !!
Good stuff! I've been a drywaller for most 20 years now so I had to see this. Because I do steel stud I always have black chalk in my line, I need to get 2 lines going cause your right about it staining. I like the 1" olfa because I tape cut everything and it's good for itch and poly so I just use that one instead of multiple. Love your vids mate!
Your California patch you showed is the best drywall tip I have ever seen. It works flawlessly. I was pretty good at patching holes but after I tried that my patching time improved drastically and it’s impossible to spot. THANK YOU!!
I've been hanging board for 2-1/2 years. Instead of measuring all the way from the top throw a piece of scrap on the floor and measure off that. I use a small piece of a pool noodle to stuff in a box containing outlet(s). Then you can router it no worries. Pull out foam after routered. Not only brick but any Concrete wall surface you want to leave quarter inch gap for tear away. I use DeWalt drywall guns and cordless routers. I prefer Hitachi but DeWalt batteries seem to last longer as of now. Also, I prefer inch and 1-5/8" screws for hanging 5/8" lids as they have a PH2 tip that comes in the case of Grabber screws. They allow you to get a slightly better grip on the screw heads. A slightly narrower screw driving head is better for 1-1/4" screws. Anyway, on that note I highly recommend grabber screws for quality fasteners. Why don't you use any drywall adhesive prior to hanging rock?
2:40 It would have been nice to mention why 1 1/4" screws for 1/2" board...to reduce the risk of screwing into electric wire. Hopefully wire is in the middle of studs so there's about 1 1/4" of wood before the hole for wire. So a 1 3/4" screw would be max in theory but holes aren't always perfectly centered so not a lot of leeway there. There are also wires running along studs and joists and where they go into electrical boxes the wires are very close to drywall on an opposite walls. No problem if the screw hits the stud, but if you miss... Longer the screw, higher the risk.
That is an added benefit, but most jurisdictions mow require plates to protect wires. Of course that does nothing if the screw misses the stud and subsequently the plate.
@@RehabLife I don't know about the States, but up here in Canada a protection plate is only required if the hole/cable is less that 32mm or 1-1/4" from the edge of the building member. I always put them where I know cabinetry will be installed or other risky areas, but not everyone will.
@@RPGDonkey yeah, I think technically as long as the hole is in the center of the stud it doesn’t have to be there, but in reality almost none are so I just put them everywhere. It’s cheap insurance.
The "rule of thumb" is that 1-1/2 of the width of material held needs to be penetrated by the screw. So, for 1/2" drywall that is 3/4". That's where 1-1/4" comes from. With only 3/4" protruding into the stud, there is plenty of margin because a 2x4 is 3-1/2", 2x6 is 5-1/2". Halfway is 1-3/4" and 2-3/4" respectively. In Ontario the building code calls for rough-in wiring to be centered in the depth. That leaves about 3/4" for 1/2" rough in drilled hole into a 2x4 partition wall. Any rough in electrician drills the hole mid depth and in a horizontal line to make it easier to pull. Rough wiring is usually mid stud for stapling and boxes are 2" deep or 1-1/2" back from the face of the stud. Plates aren't required if rough in wiring is done to code. If the rough in hole is an inch or less from the surface of the stud due to being misdrilled. plates are required. That is the responsibility of the rough in electrician, not the rocker.
I've been drywalling for 20 years here in the UK. Lot's of good points but I have a couple extra things that I always do. BTW I wasn't sure what tool you showed at the start but I recommend an impact driver with 4 setting such as the Hikoki, make sure you use a PH2 dedicated bit that fixes directly in to the tool, not a bit holder. The impact driver means you can go in to tough old timbers or new ones by just adjusting. It has a specific setting, fast start then upon resistance drops torque. OK tip 1*, always put your 8x4's on 2 pieces of timber to raise them off the floor for cutting, or even better stick the pile on a pair of Stanley Junior Saw Horses, man this makes things much faster and much easier, particularly for complicated cuts. Change your blade every day at the least, guys using blades for weeks are just disorganised, blades cost pennies. Looking forward to see how you fix more than a single board.
one thing not covered here is when doing an outside wall there will be a gap by the floor. Always mud or calk the gap to prevent drafts. The house should already be sealed and the insulation should be doing it's job, so this is a belt + suspenders deal. BTW, I was at a job years ago where the electricians drilled from the basement to the attic on an inside wall for about 10 wires within the same bay. It created such a draft that the heating / cooling t-stat was always off by a mile. Of course the attic had a plywood floor right down the center so not easy to find.
I think the reason why drywall is used is BECAUSE it is cheap and easy. If you screw it up just tear it out and do it over. If you want to knock a hole in the wall and run some cable? Piece of cake, easy to patch. It's like it was made to be destroyed and repaired. Dents are easy to patch. It the material was high quality it would be hard to repair. Patching wood panel is not easy. Replacing old panels and finding ones that match, not easy. Drywall is like cork board for hanging photos. Thumbtack the hell out of it. Nobody will notice.
You always have new tools😂 I just started drywalling my walls.. haven’t tackled the high ceilings yet.. but thanks to your videos I’m able to do this job .. I also used a tip if putting wood shims behind uneven walls!
Hello! I just wanted to say thank you for posting all this great information! I'm working on drywalling my attic with attic trusses and six dormers. I think this will definitely help me reduce the amount of mistakes I make! I just noticed that you were making marks on the wall with measurements at 5:40, I'm sure doing that will save me a lot of headaches in the future remeasuring. Thanks, Caleb Hudson
My dad has 25+ yrs of experience with multiple companies and multiple residential, demo/remodel, and commercial project. I working drywall full time with him as subcontractors. I still find 45 degree angles hard to figure out especially when there's multiple angles aside from just 90 degree spaces. I'd say I'm fairly good at hanging and measuring and just problem solving issues we encounter to make it easier and better outcome for finishers. Knowing how to joint drywall together and prep the work as you go for the next process is important and you'll stand out in the crowd. Hanging drywall is honestly just geometry in some sense especially if framed correctly there's so many efficient simified ways to find multiple measurements and just knowing where butt joints need to go and how flats/factory joints have to go with the least joints possible (leave a cleaner and better result). Anyone can hang drywall but only a few hang it well and properly like this guy, it shows on the precision!
45* .. whatever you measure across .. measure the same down .. simple as. If that doesn't work for you, cut a small but off the end of a sheet and set in place against the wall or sheet your joining to to find where it hit. Mark it on the wall or sheet you're coming off of and measure to closet wall to the mark and there you have it!
@@liz6034 to win a small chunk cracks from the back side and bulges forward. If that happens the only way to fix it is to cut out all the loose stuff and then mud the huge hole.
Putting my house back together after Ida and just hung the drywall in one room, first time doing it. I made all of these mistakes. Getting more material this weekend for the other rooms so I'll be more careful. Going to watch the rest in the series now.
screws: 3/4 + thickness of your board. 1/2" board = 1 1/4" screw. If you are going through two sheets or even covering old lath/plaster , for whatever reason, factor that into you calculation. And longer screws don't always mean better strength (home owner myth). As screws have less shear strength compared to nails. Once you get 3/4 to 1" of depth, the board will be fine. A 3" drywall screw (if there is such a thing?) is no stronger than a regular 1 1/4" when hanging boards.
Just finished doing the entire upstairs drywall in my 1930s cape cod down here in NY, about 400sqft with 2 large dormers. Talk about nothing being level from top to bottom, especially with angled and tapered ceilings 😅 Great explanations for everything.
10:02 health and Safety tip. Keep your work area tidy. I usually sweep as I go in my cutting location. Nothing worse than cutting while going backwards (a dangerous maneuver in general on a job site) and tripping over some offcuts of lumber, drywall or standing into your box of screws. Those drywall screws have a corse thread and when you are installing thousands of them you end up with bits of black metal in your skin from handling. I use a thin set of gloves such as the mechanix style when installing board, plus helps your grip.
I've got a rookie mistake for you. Working on my bathroom and I keep finding small blue strings in my mud and its driving me crazy. Found that I was mixing my mud in a blue Lowes bucked and as I was mixing the knife was scraping off the plastic in the bucket! Drove me nuts for an entire afternoon!
Thank you for the great info. I insulated my 10x20 shed myself, and the next step is drywall. Now I know to buy the right equipment. Another tool on my Ryobi list since I have plenty of batteries.
Made every mistake you mentioned this week while trying to patch up some of our remodel work. At least I have an entire 15 foot wall to do next thst I won't be making the same mistakes on!
I've just tape and jointed my first ever bit of drywall... A recess with 2 internal angles, a straight butt joint and a normal straight tape joint. Think I've made a really mess. Respect to you doing such helpful videos. Just wish I'd watched this before I started 😢
Thank you, I'll be rewalling a garage with a laundry room inside it. You have shown me so much, not just a video here and there. We in Australia also you use glue as well as screws or nails to fix the drywall to the boards.
Great video. I work alone alot and can relate to the chalk line not grabbing even a pristine corner. I sometimes make a small incision on the backside of a sheet of drywall or cut a notch with my chisel on plywood. It grabs the line and acts like having a second hand. Or I keep a small spring clamp on my belt.
Keep a honing stone handy and you will decrease your blade expense to minimal. It's quicker to hone a blade already installed the fixed-blade than to change to a new blade. Efficiency max.
Thanks, as an occasional drywall DIY I can't believe how many of these mistakes I routinely make. I can't wait to get at another project in January and do it properly/ easier. Looking forward to the next 2.
Great vid for anyone wanting to know about hanging Sheetrock, and also, YEPPERS……making a vid explaining all this stuff and working with tools; not easy all the time😉 Definitely LIKE that you show the mishaps, mistakes, errors, and so on; and laugh and have fun with it…..B/C no matter how long been in a trade (or any job) you’ll make a mistake now and then. How you fix it (or others….that comes up a lot, don’t it🙂) is what matters: is what ppl say, BUT it also shows and tells how good/skilled you are b/c there’s some jobs you walk into knowing your there to fix someone’s else’s mistakes, and it can be “interesting” & “nasty” sometimes (I’m sure y’all know what mean if been doing this long enough). GOOD VID, looking forward to NEXT✌🏻
I work as a carpenter/punch-list guy, and I'm guilty about trying to fit things in too tightly when I do drywall work. It's a simple thing, but it does cause problems. Thanks for the advice. I'll try to remember to be more generous in my measurements.
I switched to Shinwa chalk lines because they automatically retract the string, use a very fine string, and use a pin rather than a hook on the end of the string. The pin will stay put and can be stuck in the middle of a sheet or board as well as the edge. It’s a game changer for carpentry and drywall.
Cutting the board to get a chalkline mark, if u even need to use a line, is easier if you just use your knife to make a small slit to set your line anchor in.
I'm sorry, but I've hung drywall for over 30 plus years and this guy is hilarious. I'm not saying that he done everything wrong, but he's making a video showing beginners how not to make mistakes and I saw so many rookie mistakes that he made. Dig your blade into the edge of the board when using a chalk line so your string will stay put. Do not cut on the left hand side of your t-square unless you can absolutely not help it. When you start screwing off the board keep that screw gun switch locked so it continues to run and you will not miss so many screws. I could go on and on, but no one's perfect. LOL
i had that feeling, hes just way to clean-cut to be a pro. never trust "pretty hands" they havent done any work, for me as a beginer its so irritating that NO ONE TALKS ABOUT LEGAL CODE!!!!! that the only fucking thing im watching for!!!! and no one KNOWS CODE, or thinks is so elementary that everybody should know code LAW!!
Ah, those early days of DIY drywalling. I would lay the sheets on a sawhorse table to make every cut. Was doing electrical work on a commercial job site and learned so much from watching and questioning the pros. Ask them first if you can ask questions. Fast and cheap? Currently working in a owner home build home from the 70’s. The wallboard is really soft like it’s wet.
I was looking for a video to share with a friend i can’t help this is great. The first screw mishap😂 had me rolling. The stripping sound 😂 and a miss. Way to be a champ and not edit it out. Have a good weekend.
17:00 you went through the drywall and missed the stud 😂😂😂 I heard it. Then you ran the gun to make it sound like you went through right 😂😂😂. Was a good laugh. We all do it sometimes.
Very good video! I’m a homeowner who does very nice work & takes too long on the job. I did learn a few things, (I usually score too deep & cut too tight). I also need to buy a panel lift & router. I’m doing my laundry room in January. Thank you for your valuable wisdom.
i allways use white chalk for drywall, chipboard or any surface that will be painted since SOME blue chalks stain too, and if nothing else it gives peace of mind when the chalk lines are invis after just the prime coat, might be paranoia in most cases but after that one time when i blue chalked and the blue pushed trough the primer and final paint and i had to re-prime with Akrostop and re-paint the blue lines the cost of an extra chalk liner and a bottle of white chalk felt like a non factor, now i only use blue for lines that wont be painted.
I admire anyone that uses imperial measurements with all the halves/ quarters / sixteenths etc... such a confusing / complicated system when compared to Metric
I do rough carpentry and we only measure to the nearest eight inch and say strong or weak for the 16th. 3/4 weak or 5/8 strong is a lot less confusing than saying 13/16ths. Lay out all your lines before you make a cut so you don't lose your marks that or mark it where it won't get cut off. I appreciate him making little mistakes and not taking them out. Everyone does it even period been doing it for 30 years. Always keep learning, don't be afraid to try something different you may like it more
We don't really go beyond the 1/8 and most crews will use numbers representing 1/8" for example 49 and 1 would be 49 1/8" 22 and 4 would be 22 1/2" if we need to go to the 1/16" we would say fat or lean 22 and 4 lean is 22-7/16" much easier to write down and communicate than saying sixteenth, eighth, half, quarter. so on site we would write it down as 54-1F or 27-2L which is 54-3/16" and 27-5/16" I like the way we can break down the on center layouts since there are 48" in plywood widths, we can do framing layouts with 6", 12", 19.2", 24" on center layouts. Metric can get to be a long string of numbers I would think. Are you guys calling out stuff in mm? like 1193mm?
That’s interesting. Metric is pretty much in 10’s / 100’s and 1000’s 10mm to a cm or 1000mm to a meter Makes it easy to be precise Very simple and easy but obviously it’s all about what your used to Yea generally yell it out as millimeters. Like 2400mm. But instead of saying “two thousand four hundred” We just say twenty four hundred or 2780mm would be Twenty seven eighty for example ….. if that makes sense
@@nomadnowhere1818 the problem there is you can't evenly divide. There are only 2 factors for a 10 based system making it impractical. In real world scenarios you just keep throwing away the excess so the numbers work out. In addition when it comes to vehicles and fasteners in particular there isn't a single system so many metric sets don't have a full complement of wrenches. I ran across that today with JIS metric on a tractor. If 10ths or the like get you excited you might be thrilled to know that machinists have been using them for a very long time without bothering with the metric system.
Use 1 1/8" screws for 1/2" sheetrock and 1 1/4" for 5/8th" sheetrock. I agree with the rest of it. You can also get a guide tip router bit for your router and cut your sheets on your wider side and zip them in for a tight fit.
Drywall is fast, cheap, and slows fires down... I'm no drywall expert, hence watching your good videos, but I like learning about the evolution of humans and their activities, Anthropology related. Anyway, some centuries ago, Paris Burnt down pretty badly. Houses were built all out of lumber at the time, including wall finishes. It was noticed that houses that had the famous Plaster of Paris on their walls wouldn't burn as fast. So the king of France ordered all houses be built with plaster of Paris to help reduce fire spread. From plaster, we now have drywall boards because it's faster to put up on walls than plaster is. 😊 you can look into it and share the info in a future video, I might get to see. 😅
I have two of those "cheese-graters" (and have had them for a long time) and never knew that they were for drywall! I had thought that they were for wood and have tried using them many times but, not surprisingly, I was never very satisfied with what happened. Time to move them to the drywall tool box. :)
When you mentioned drywall not being a good product but it fast and cheap reminds of the British home improvement channels. They plaster their new walls and if they have 2 repair existing walls....those are replastered as well.
if you have someone hanging for you as you are laying out and cutting sheets you can mark screw layout with your t square on the sheet for accuracy especialy when your training a new guy.
this video has come too late for me. Watched many of your videos to learn as I went, as I was doing my reno and basically made most of the mistakes you mention. I'm afraid to watch your sequel to this. As they say "ignorance is bliss" at this point.. perhaps I don't want to know lol
As an electrical contractor, I do appreciate your pointing out to NOT overcut outlets. Watching your channel cause I am about to get messy with drywall at my own place. Hope I don't screw it up, well, screw it up in the wrong way!
Amazing videos. I'm just starting out getting my own Reno business going. You are by far my favorite. Very informative. I live on the Sunshine Coast in bc, so you being in Vancouver is pretty cool. Your videos are going to be my go-to for learning as I go. Thank you for your vids.👍
G'day, Kevin here from Australia. I'm plastering a extension out (just the cornice to go now) and here we have to use stud adhesive when hanging plaster. You don't? And I have studied your videos and I must say my plastering skills have improved outersight especially my external corners. So thanks for sharing. ✌🏻 Peace
glue is available in North America but cannot always be used. Most times it is for added noise cancellation when laminating boards together. We use Vapor Barrier (Plastic) on the exterior walls in Canada as a moisture barrier and as such you cannot bond directly to the framing member. Internal walls are fine. I've started doing it for ceilings and is worth my extra effort cuts down on fastener holes too.
You saved me so much time, money and frustrations. Fixed a 18ft tall 40x30 sagging ceiling. Scraped 4x as much painted popcorn ceilings. Countless nail pops. 10 peaked sheets. Covered textured walls with skim coats. Replaced a 4x3 section of ceiling. Numerous failed tapes and cracks. and everything is PERFECT. Took me 80hrs lol but I'm happy. THANK YOU!!!!!!!!!!! BTW Wet sanding with a microfiber backed sponge in a circular motion THEN sanding gave me a level 5 finish.
Awesome! I’m so glad the videos helped. And thank so so much for the generous super thanks! Looks like I can support my luxurious coffee habit for one more month😂❤️
@@vancouvercarpenter you're welcome! I ruined the perfect walls and ceiling I created by not having enough pressure in the paint sprayer. So now I get to do it all again!!
I'm actually considering flat wallpapering the whole thing and skimming the joints. I just don't think I have it in me to skim and sand it again. Have you ever done this?
@@michaelc9248😢
For those who don't understand why 1 1/4" is the right length for your drywall screws, that length is long enough to reliably grab the stud without hitting wires hiding behind. Electricians are required to have their wires deeper than 1 1/4" from the surface of the stud, so the thickness of your drywall is your safety cushion. On the rare occasion when they can't get wires deep enough, such as on a corner, they nail a plate to prevent misadventure. Buy the right length of screws and you won't likely burn your house down.
Great point and who wants to drive screws any longer than you have to
@@fayekephart848 exactly. Nobody uses anything longer than 1 1/4" anyway unless you are double layering the drywall.
How about for 5/8 drywall?
@Alex its the same. 1 1/4 screws
Not sure if same building code everywhere in North America but where I live, they put the plates everywhere that a wire passes through a stud.
You are seriously the drywall whisperer. Time and again I watch your videos and walk way so much more informed than I ever anticipated and it’s saved me not only my initial questions, but future headaches as well.
The bald guy in the blue collar shirt is good too
Can't remember the name of the channel
Home Renovision DIY
Check It out
I like that you don't edit out the parts that show you're not perfect even though you (definitely) are a pro. It gives us beginners more lee-way to not expect us to do things perfectly or without a hitch. There's a learning curve for beginners and they shouldn't judge themselves as lacking anything because of it. I also like reading the comments as the comments provide their own useful tips to be considered and additional insights. Your channel and fanbase is the best!💖
A drywaller with 15+ years experience here. I have a very similar set up belt, but I've got a trick for you to use if you'd like. Instead of keeping your measuring tape on the right pouch, keep it in the smallest end pocket on your left pouch. So when you need to take out your knife and tape to do the sliding technique, or tape and pencil to make a mark, you've got both ready to go at the same time. It saves about 3 seconds, but when you have to do that 200 - 300 times per day it adds up.
I like using the old fashion 16 ft stanleys with a metal casing ,theyre super fast to grab and throw back in your pouch .
@@liberty4617 ya I've always been a fan of Stanley's Fatmax 16ft tapes. Probably gone through over 30 of them by now
Definitely. And you can grab your tape and knife or tape and pencil or tape and pen. At the same time.
Red gang.
I just keep one tape on the right side, one on the left and one right in the front. all 35' fat max tapes. lol
People think tradesmen are tradesmen because they aren't capable of thinking on the level of a doctor or lawyer but a good tradesman Is the master of critical thinking, thinking ahead and problem solving. That's why doctors and lawyers hire them to do things like this. If it was easy anyone could do it.
100%. True experts.
I'm pretty sure no one thinks that lmao. They just never wanted to be in school forever.
Mostly for me it's the constant problem solving and procedural planning.
Always like and appreciate your videos. As a chick in a "man's" field, it's very helpful to have reinforcements when someone says, "why are you doing it like that?". Thank you. Keep in mind I live in the southern US where I'm not always taken seriously.
Yeah... Some of the old heads have some fragile egos. I don't have to deal with the sexism, but since I'm in my 30s, I frequently deal with the "I've been doing this since before you were born" attitude. Thankfully, a lot of those attitudes are aging out with the generations most responsible for them. It'll be our world soon enough :)
Also, after a little reflection, I should state that I didn't intend to make your post about me. There's enough dudes out here derailing the conversation in their favor, even if it comes with the best of intentions. We can all be a little more mindful sometimes :) Good luck out there, J!
Lol no worries!
And thank you 😁
I'd just be happy to have someone help me that is competent in drywall ... perhaps it would make up for my incompetence ... usually the mud man hates to finish drywall that I have installed ... and of course I am the mud man too.
Oddly this is the absolute most “How to hang dry wall” video I’ve found even if it wasn’t the way you intended to frame the video. Super helpful and I feel much more prepared to dry wall over the siding in my house now. Thanks a tonne!
Love watching your videos. I am doing a whole house renovation, and your videos have been a life saver. The first one I watched was on trimming out windows. Thanks to you, my windows look perfect. You are fun, entertaining, and informative. You aren't afraid to make a mistake. They become a learning experience for those of us out here who will make a ton of them. Thanks so much for your time and expertise.
Also thank you for your videos. I used so many of your videos to help me fix my walls cracking and destroyed corners, and several cracks. No experience and you were huge help. Husband is happy and was just expecting me to paint over cracks, he was quiet impressed I fixed the wall first.
I’ve drywalled a few rooms in my house, self taught. I learned so much from this video, wish I would’ve seen it before I did anything, would’ve saved me so much time!
Glad to be watching it now lol..
'I've said it... you don't need me to say it again!' -You're great Ben, and a thoughtful person for catching yourself repeating!
Trying to learn drywall basics to improve my handyman business. I appreciate how you simplify everything.
Glad to help
I did the same with plastering thanks alot man
Curtis Aitken, how’s the handyman business going? Asking because I pretty much hate my day job and have been thinking about starting a side handyman business and seeing how it grows. Not sure how it is in your neck of the woods but trying to get any professional in to do work they are either booked out 6 months or charging a heavy premium. If you don’t mind replying would really appreciate it.
@@72cgray I'm not a handyman but research the laws concerning handymen in the state you live in. Unless you have a contractor's license, there are many restrictions on what handymen can and cannot charge for jobs. In fact, my GF just took a handyman to court and won. The judge did mention that the handyman should've had a contractor's license because his rights are very limited as a handyman.
@@72cgray it depends on what state you are in. I am in SW Florida. In Florida I am not “allowed” to do any electrical. I am not “allowed” to do any plumbing behind the walls. The fact that I can depends on the client. I won’t do anything that puts my insurance at risk. The insurance is cheap, the license here is easy. I’ve just started about 2 months ago and it’s my full time. The hardest parts are figuring out what/how to bill your clients and learning to say no. I work in a very small geographic area. I’ve not had any days off I don’t want. Know your worth and be honest…you’ll go far. I charge $75 an hour and they buy all the items they need if they pick them up or pay me the $75 an hour to goto the store to pick them up. Be consistent, honest and the rest will come to you by word of mouth.
This is the best drywall channel; I’ve learned so much. Gotta stop overdriving my screws.
Man oh man. This Vancouver carpenter is so good at teaching techniques of carpentry with an easy going presence. There should be Oscar type awards for these helpful videos.
Just a tip for chalk line. Cut through the board with your knife quarter inch or so and throw the chalk line in the grove with the holder pulled out the back side. Works better that way and won't fall off. Also any extreme angles will become much easier.
Ignore this
He needed a jab saw I always use my jab saw
I appreciate how you looked for space in the outlets without wires before you router the hole. As an electrician I can tell you that not all drywall guys worry about that. Have had to fix plenty of wires chewed up by routers over the years. Thanks for your attention to that detail!
As a drywaller for 15 years after being chewed out for chewing up wires like going in the box with the routers I made it a rule stay on the outside of the box by 1/8 of an inch plate covers it and you don't have an electrician all over your ass
On another thought I can tell how good the electrician is by if I measure from the floor up to the bottom of the box after a measure a dozen of them and they're all set it 15 or 16 in I figure I can trust them not be all over the place with their measurements
Good info… regarding setting the screw depth, I’d add that replacing the Phillips bits frequently helps. This as as the bit wears the depth the screw is sunk decreases. The wear occurs very little from screw to screw but after a 1,000 screws it’s noticeable. Don’t cheap out on changing blades and bits… they are consumables!
Your bits last 1000 screws? Mine last about 25 screws I think while using my impact. I bought a box of bits
@@infotechsailor Mine... No! That was my point! On the other hand, I've seen guys with bits so rounded off that they had to put a lot of pressure on the driver to keep the bit engaged in the screw head... and they kept messing with the depth adjustment. That comment was for "those" guys. 😜
@@infotechsailor You need to buy better bits. You should be getting at least 100 screws per bit. Better yet, get Torx drywall screws and you will get even more out of the bit.
I love your videos. And I don't mind seeing little mistakes. Because you show how to fix them. That's real life! Thank you!
Drywall fast and cheap. But also fire resistant. I grew up in a house in California that had 1/4" Mahogany plywood for the walls. Ours was painted white but our neighbors was varnished. Their house caught fire and was gone in 15 minutes. Their garage didn't have the original Mahogany plywood and had been drywalled and was the only room left standing. The next week my father ripped our Mahogany out and replaced it with drywall. I had stucco concrete walls in one house designed as a passive solar experiment. The walls were done like a basement. It made the house very quiet as it blocked outside noise. But much harder to work with than timber frame and drywall. If you want wood or some other expensive material put drywall behind it. It may save you life.
and for the cost, drywall is very sound absorbent
for those that don't know, gypsum isn't just non-flammable. because it's a hydrated mineral it outgasses water vapour when it gets hot
Sad that the Mahogany paneling was destroyed. People make hasty decisions that are costly.
I found your 1- series of "every beginner Drywall Mistake I can think of" super usefull. As for the flow of the edited videos - GREAT. Did not impare the great info your shared!
Its a gift to know something well enough to find the confidence in competence to instruct others in it. I'm just fixing up my house and this was priceless! Gracias!
I made a small steel box that fits perfectly inside an outlet without wiring device (no gaps), mounted two neodymium magnets on top. Cover drywall without any cutting and then use another magnet to find the outlet behind. Then just router it, first inside (plate protects the wires), then fine perimeter cut to outside dimensions. Saves lots of time on measurements and alway perfect result. Just wanted to share, not sure if there are similar things out there on the market...
A type of your solution is standard in Sweden. But the inner casing of our electrical outlets are round. So you can use a hole saw on the drill and cut around the magnets. Even a beginner can get a good result within 30 seconds.
Never in my career as a sheet rocker have I ever heard someone say “unfortunatly we don't have any ceilings to hang” lol. I so much good info in your videos!
A little trick I use for outlet/switch boxes that I find really handy is i'll wet my fingers with water and put water on the box face (outlet/wires pushed inside box. You then put your sheet up against and give a few knocks where boxes are. When you pull the drywall back off wall you have a perfect outliine of where box is, then use a oscillating/router tool to cut it out.
Try red lipstick. Been using this for over 20 years. Don’t tell wife!
I used to live in Vancouver and used to do renovations so did this a lot. Its been a hood handful of years though so its nice to get a refresher in. Also, the drill always found a way to embarrass me too when others would watch and commentate so I feel ya . Love the videos and look forward to continuing the journey
There is definitely a rhythm to hanging drywall. I do a lot of patchwork and these are helpful tips to remember! Now you have to do “Every mistake newbies make when taping!”
As a taper I feel obligated to say he should not do it becuse I have seen his taping videos and he doesn't know how to tape but I am glad he was taping to understand how to hang drywall. Just a shame no drywaller will watch this video and take notes. These are not newbie mistakes. Almost all drywallers make them because they don't have to fix their stuff. An example even he did a mistake that will cause nail pops. He doesn't know that because it was never his job to fix them and the mistake that will cause it isn't inexperienced screwing but he screwd top and bottom and then went in the middle. My english isn't good enough to explan it but the board could sliglty bend in the middle because of it and the screws will force the mid to get to the studs and eventually it would cause nail pops.
Good advice on setting cutting area up. One thing I do is put paper or plastic down in the cutting area. Once all the boards are cut fold up up and clean all the chunks up. In a Home Reno this saves on the mess.
Hi thanks for videos fun to watch! Just want to say that the "reason" for the crumbly drywall besides being fast and cheap is that it is very fire proof, and in fact if it gets hot it "bleeds" moisture!
Sometimes in commercial buildings they require a "firewall" which means about 3 layers or more.
In elevator shafts its 1 1/2 thick stuff only 2ft wide.....this is for fire protection and making sound proof too.
We used to always go "to and through" light boxes, which means a number (AKA "give me some numnums bubba") for near edge, and a number for far edge, so if you are on ladder taking the numnums, you want to tell partner doing cuts on ground for example 32 to it, and 34 through it....and from the "ups" or "the buttedge"
Also we didnt say "one and three quarters" or "two and three eigths" instead go by eighths of inch - for example one and three quarters would be: "one and six", and for two and three eights you would say "two and three" For a quarter inch or half inch, you can say "quarter " or "half" however......thats how we did it down in Seattle in the Carpenters Union work at least. Most of time two people, so lots of times one gives numbers, one does the cuts when doing ladder and scaffold work.
Also in the nitty gritty numbers, you say "shy" or "strong" which means 1/16 to 1/8 less or more to the cut.
We called the board lifter thing a "kicker" the hole cutter the "circle jerk"
From Pink Floyd song to keep amused on job: "we dont need no insulation" and "we dont need no fire control" with british accent....
AjsoL "Ah love drahwall.... drahwall is mah life" with dumb hillbilly accent...
"you only need to be a little bit smarter than the board you hang" a good motto
Careful of stacking too many boards angled white side out on wall - as if it falls towards you you can break leg easy! That stuff is heavy.
Great videos I had fun back in the days hanging sheetrock actually looking back at it. Mudding was always a mess!
"dont worry the tapers will fix it!" and move on to next board....(sometimes paid by the sheet non-union work)
Once we did a house that had no permit to an add-on, and the living room and bedrooms rested just on concrete blocks on top of dirt - no real foundation....we didnt know this, and cracks kept appearing everywhere because of the added weight of drywall on walls made it sink... it was total nightmare we had to go back and fix over and over...finally asked my old boss to take a look, he noticed the foundation nonexistent....so example of not being a bit smarter than the board you hang.
I have been watching a lot of your videos and the information is amazoning. I have learned a lot about DRYWALL from your videos and again i am amazoned !!
Good stuff! I've been a drywaller for most 20 years now so I had to see this. Because I do steel stud I always have black chalk in my line, I need to get 2 lines going cause your right about it staining. I like the 1" olfa because I tape cut everything and it's good for itch and poly so I just use that one instead of multiple. Love your vids mate!
I use the 1" olfa for everything else🙂
Just wondering what chalk color has to do with type of framing?
Your California patch you showed is the best drywall tip I have ever seen. It works flawlessly. I was pretty good at patching holes but after I tried that my patching time improved drastically and it’s impossible to spot. THANK YOU!!
I've been hanging board for 2-1/2 years. Instead of measuring all the way from the top throw a piece of scrap on the floor and measure off that. I use a small piece of a pool noodle to stuff in a box containing outlet(s). Then you can router it no worries. Pull out foam after routered. Not only brick but any Concrete wall surface you want to leave quarter inch gap for tear away. I use DeWalt drywall guns and cordless routers. I prefer Hitachi but DeWalt batteries seem to last longer as of now. Also, I prefer inch and 1-5/8" screws for hanging 5/8" lids as they have a PH2 tip that comes in the case of Grabber screws. They allow you to get a slightly better grip on the screw heads. A slightly narrower screw driving head is better for 1-1/4" screws. Anyway, on that note I highly recommend grabber screws for quality fasteners. Why don't you use any drywall adhesive prior to hanging rock?
2:40 It would have been nice to mention why 1 1/4" screws for 1/2" board...to reduce the risk of screwing into electric wire. Hopefully wire is in the middle of studs so there's about 1 1/4" of wood before the hole for wire. So a 1 3/4" screw would be max in theory but holes aren't always perfectly centered so not a lot of leeway there. There are also wires running along studs and joists and where they go into electrical boxes the wires are very close to drywall on an opposite walls. No problem if the screw hits the stud, but if you miss... Longer the screw, higher the risk.
That is an added benefit, but most jurisdictions mow require plates to protect wires. Of course that does nothing if the screw misses the stud and subsequently the plate.
@@RehabLife I don't know about the States, but up here in Canada a protection plate is only required if the hole/cable is less that 32mm or 1-1/4" from the edge of the building member. I always put them where I know cabinetry will be installed or other risky areas, but not everyone will.
@@RPGDonkey yeah, I think technically as long as the hole is in the center of the stud it doesn’t have to be there, but in reality almost none are so I just put them everywhere. It’s cheap insurance.
The "rule of thumb" is that 1-1/2 of the width of material held needs to be penetrated by the screw. So, for 1/2" drywall that is 3/4". That's where 1-1/4" comes from. With only 3/4" protruding into the stud, there is plenty of margin because a 2x4 is 3-1/2", 2x6 is 5-1/2". Halfway is 1-3/4" and 2-3/4" respectively. In Ontario the building code calls for rough-in wiring to be centered in the depth. That leaves about 3/4" for 1/2" rough in drilled hole into a 2x4 partition wall. Any rough in electrician drills the hole mid depth and in a horizontal line to make it easier to pull. Rough wiring is usually mid stud for stapling and boxes are 2" deep or 1-1/2" back from the face of the stud. Plates aren't required if rough in wiring is done to code. If the rough in hole is an inch or less from the surface of the stud due to being misdrilled. plates are required. That is the responsibility of the rough in electrician, not the rocker.
@@dondonaldson1684 I do everything so, it’s ultimately my responsibility
I've been drywalling for 20 years here in the UK. Lot's of good points but I have a couple extra things that I always do. BTW I wasn't sure what tool you showed at the start but I recommend an impact driver with 4 setting such as the Hikoki, make sure you use a PH2 dedicated bit that fixes directly in to the tool, not a bit holder. The impact driver means you can go in to tough old timbers or new ones by just adjusting. It has a specific setting, fast start then upon resistance drops torque. OK tip 1*, always put your 8x4's on 2 pieces of timber to raise them off the floor for cutting, or even better stick the pile on a pair of Stanley Junior Saw Horses, man this makes things much faster and much easier, particularly for complicated cuts. Change your blade every day at the least, guys using blades for weeks are just disorganised, blades cost pennies. Looking forward to see how you fix more than a single board.
one thing not covered here is when doing an outside wall there will be a gap by the floor. Always mud or calk the gap to prevent drafts. The house should already be sealed and the insulation should be doing it's job, so this is a belt + suspenders deal. BTW, I was at a job years ago where the electricians drilled from the basement to the attic on an inside wall for about 10 wires within the same bay. It created such a draft that the heating / cooling t-stat was always off by a mile. Of course the attic had a plywood floor right down the center so not easy to find.
I think the reason why drywall is used is BECAUSE it is cheap and easy. If you screw it up just tear it out and do it over. If you want to knock a hole in the wall and run some cable? Piece of cake, easy to patch. It's like it was made to be destroyed and repaired. Dents are easy to patch. It the material was high quality it would be hard to repair. Patching wood panel is not easy. Replacing old panels and finding ones that match, not easy. Drywall is like cork board for hanging photos. Thumbtack the hell out of it. Nobody will notice.
You always have new tools😂 I just started drywalling my walls.. haven’t tackled the high ceilings yet.. but thanks to your videos I’m able to do this job .. I also used a tip if putting wood shims behind uneven walls!
Man, you're totally real...not afraid to admit you made a little mistake...but anyway, great stuff! I definitely learned some tips! Thank you!
Hello!
I just wanted to say thank you for posting all this great information!
I'm working on drywalling my attic with attic trusses and six dormers. I think this will definitely help me reduce the amount of mistakes I make!
I just noticed that you were making marks on the wall with measurements at 5:40, I'm sure doing that will save me a lot of headaches in the future remeasuring.
Thanks,
Caleb Hudson
You can always use a scrap piece to put your measurements on.
I love your humbleness my friend, even the best of us make the simple mistakes. Keep it up the good work sir
Wish you would have done this video years ago!! I made a lot of these mistakes when I first started out. Great videos. Still learning lots.
I hate drywall it's a pain in the butt, so thanx for the vids bro! Not boring and very helpful!
My dad has 25+ yrs of experience with multiple companies and multiple residential, demo/remodel, and commercial project. I working drywall full time with him as subcontractors. I still find 45 degree angles hard to figure out especially when there's multiple angles aside from just 90 degree spaces. I'd say I'm fairly good at hanging and measuring and just problem solving issues we encounter to make it easier and better outcome for finishers. Knowing how to joint drywall together and prep the work as you go for the next process is important and you'll stand out in the crowd. Hanging drywall is honestly just geometry in some sense especially if framed correctly there's so many efficient simified ways to find multiple measurements and just knowing where butt joints need to go and how flats/factory joints have to go with the least joints possible (leave a cleaner and better result). Anyone can hang drywall but only a few hang it well and properly like this guy, it shows on the precision!
45* .. whatever you measure across .. measure the same down .. simple as. If that doesn't work for you, cut a small but off the end of a sheet and set in place against the wall or sheet your joining to to find where it hit. Mark it on the wall or sheet you're coming off of and measure to closet wall to the mark and there you have it!
When cutting the drywall make sure you don't leave chunks on the floor behind the drywall when you're screwing it to the wall or you'll get blowouts.
Can you expand on that for really new newbies? I guess I'm not sure what a blowout is.
@@liz6034 to win a small chunk cracks from the back side and bulges forward. If that happens the only way to fix it is to cut out all the loose stuff and then mud the huge hole.
Your videos are so helpful and interesting, (for those of us who like to drywall and mud lololol). Thank you. I use your tips frequently.
Putting my house back together after Ida and just hung the drywall in one room, first time doing it. I made all of these mistakes. Getting more material this weekend for the other rooms so I'll be more careful. Going to watch the rest in the series now.
“Don’t make these beginner mistakes”
*proceeds to router live outlet box* 😂😂😂
screws: 3/4 + thickness of your board. 1/2" board = 1 1/4" screw. If you are going through two sheets or even covering old lath/plaster , for whatever reason, factor that into you calculation. And longer screws don't always mean better strength (home owner myth). As screws have less shear strength compared to nails. Once you get 3/4 to 1" of depth, the board will be fine. A 3" drywall screw (if there is such a thing?) is no stronger than a regular 1 1/4" when hanging boards.
My new favorite Carpenter..... bet you curved wall work is amazing.
Thanks!
You are talking to the camera like me(the viewer) is right there. It really makes viewing experience more enjoyable.
Just finished doing the entire upstairs drywall in my 1930s cape cod down here in NY, about 400sqft with 2 large dormers. Talk about nothing being level from top to bottom, especially with angled and tapered ceilings 😅 Great explanations for everything.
10:02 health and Safety tip. Keep your work area tidy. I usually sweep as I go in my cutting location. Nothing worse than cutting while going backwards (a dangerous maneuver in general on a job site) and tripping over some offcuts of lumber, drywall or standing into your box of screws. Those drywall screws have a corse thread and when you are installing thousands of them you end up with bits of black metal in your skin from handling. I use a thin set of gloves such as the mechanix style when installing board, plus helps your grip.
Wah wahhhhh
I've got a rookie mistake for you. Working on my bathroom and I keep finding small blue strings in my mud and its driving me crazy. Found that I was mixing my mud in a blue Lowes bucked and as I was mixing the knife was scraping off the plastic in the bucket! Drove me nuts for an entire afternoon!
Those buckets will also crack over time and if you stand on them they can buckle on you real drywall buckets wont do that .
Great information Vancouver. Putting my list of supplies together right now. Thanks for sharing the video.
You are a great teacher! Getting ready to remodel my bathroom and I learned so much (especially
what NOT to do) - THANK YOU!!
Thank you for the great info. I insulated my 10x20 shed myself, and the next step is drywall. Now I know to buy the right equipment. Another tool on my Ryobi list since I have plenty of batteries.
Made every mistake you mentioned this week while trying to patch up some of our remodel work. At least I have an entire 15 foot wall to do next thst I won't be making the same mistakes on!
I've just tape and jointed my first ever bit of drywall... A recess with 2 internal angles, a straight butt joint and a normal straight tape joint. Think I've made a really mess. Respect to you doing such helpful videos. Just wish I'd watched this before I started 😢
The biggest mistake you could make is not calling this guy to do the job.
11 min in and I’ve already learned a ton. Thanks
Thank you, I'll be rewalling a garage with a laundry room inside it. You have shown me so much, not just a video here and there. We in Australia also you use glue as well as screws or nails to fix the drywall to the boards.
Great video. I work alone alot and can relate to the chalk line not grabbing even a pristine corner. I sometimes make a small incision on the backside of a sheet of drywall or cut a notch with my chisel on plywood. It grabs the line and acts like having a second hand. Or I keep a small spring clamp on my belt.
In my area, it’s code to use 1-5/8 on the ceiling for 1/2”. Nice video mate
Very watchable with great tips. Glad to see you're only human too! Now onto part 2!
Keep a honing stone handy and you will decrease your blade expense to minimal. It's quicker to hone a blade already installed the fixed-blade than to change to a new blade. Efficiency max.
I think it’s better to say this is a better way of doing it, rather than saying what mistakes others make. Just my opinion. Thanks for sharing!
Thanks, as an occasional drywall DIY I can't believe how many of these mistakes I routinely make. I can't wait to get at another project in January and do it properly/ easier.
Looking forward to the next 2.
Great vid for anyone wanting to know about hanging Sheetrock, and also, YEPPERS……making a vid explaining all this stuff and working with tools; not easy all the time😉
Definitely LIKE that you show the mishaps, mistakes, errors, and so on; and laugh and have fun with it…..B/C no matter how long been in a trade (or any job) you’ll make a mistake now and then. How you fix it (or others….that comes up a lot, don’t it🙂) is what matters: is what ppl say, BUT it also shows and tells how good/skilled you are b/c there’s some jobs you walk into knowing your there to fix someone’s else’s mistakes, and it can be “interesting” & “nasty” sometimes (I’m sure y’all know what mean if been doing this long enough).
GOOD VID, looking forward to NEXT✌🏻
I got legit excited to hear/see that you were putting this out. Got my popcorn.
I work as a carpenter/punch-list guy, and I'm guilty about trying to fit things in too tightly when I do drywall work. It's a simple thing, but it does cause problems. Thanks for the advice. I'll try to remember to be more generous in my measurements.
Way more than just beginner mistakes. Thanks so much!
I switched to Shinwa chalk lines because they automatically retract the string, use a very fine string, and use a pin rather than a hook on the end of the string. The pin will stay put and can be stuck in the middle of a sheet or board as well as the edge. It’s a game changer for carpentry and drywall.
Cutting the board to get a chalkline mark, if u even need to use a line, is easier if you just use your knife to make a small slit to set your line anchor in.
I'm sorry, but I've hung drywall for over 30 plus years and this guy is hilarious. I'm not saying that he done everything wrong, but he's making a video showing beginners how not to make mistakes and I saw so many rookie mistakes that he made. Dig your blade into the edge of the board when using a chalk line so your string will stay put. Do not cut on the left hand side of your t-square unless you can absolutely not help it. When you start screwing off the board keep that screw gun switch locked so it continues to run and you will not miss so many screws. I could go on and on, but no one's perfect. LOL
i had that feeling, hes just way to clean-cut to be a pro. never trust "pretty hands" they havent done any work, for me as a beginer its so irritating that NO ONE TALKS ABOUT LEGAL CODE!!!!! that the only fucking thing im watching for!!!! and no one KNOWS CODE, or thinks is so elementary that everybody should know code LAW!!
Ah, those early days of DIY drywalling. I would lay the sheets on a sawhorse table to make every cut. Was doing electrical work on a commercial job site and learned so much from watching and questioning the pros. Ask them first if you can ask questions.
Fast and cheap? Currently working in a owner home build home from the 70’s. The wallboard is really soft like it’s wet.
I was looking for a video to share with a friend i can’t help this is great. The first screw mishap😂 had me rolling. The stripping sound 😂 and a miss. Way to be a champ and not edit it out. Have a good weekend.
Dude, all your drywall videos are outstanding! Thank you!
17:00 you went through the drywall and missed the stud 😂😂😂 I heard it. Then you ran the gun to make it sound like you went through right 😂😂😂. Was a good laugh. We all do it sometimes.
Very good video! I’m a homeowner who does very nice work & takes too long on the job. I did learn a few things, (I usually score too deep & cut too tight). I also need to buy a panel lift & router. I’m doing my laundry room in January. Thank you for your valuable wisdom.
i allways use white chalk for drywall, chipboard or any surface that will be painted since SOME blue chalks stain too, and if nothing else it gives peace of mind when the chalk lines are invis after just the prime coat, might be paranoia in most cases but after that one time when i blue chalked and the blue pushed trough the primer and final paint and i had to re-prime with Akrostop and re-paint the blue lines the cost of an extra chalk liner and a bottle of white chalk felt like a non factor, now i only use blue for lines that wont be painted.
This. This right here is the content I come for.
Lol, I have saw your skate vids a couple years back and now I'm watching your drywall vids. Everything comes full circle.
I admire anyone that uses imperial measurements with all the halves/ quarters / sixteenths etc... such a confusing / complicated system when compared to Metric
I do rough carpentry and we only measure to the nearest eight inch and say strong or weak for the 16th. 3/4 weak or 5/8 strong is a lot less confusing than saying 13/16ths. Lay out all your lines before you make a cut so you don't lose your marks that or mark it where it won't get cut off. I appreciate him making little mistakes and not taking them out. Everyone does it even period been doing it for 30 years. Always keep learning, don't be afraid to try something different you may like it more
We don't really go beyond the 1/8 and most crews will use numbers representing 1/8" for example 49 and 1 would be 49 1/8" 22 and 4 would be 22 1/2" if we need to go to the 1/16" we would say fat or lean 22 and 4 lean is 22-7/16" much easier to write down and communicate than saying sixteenth, eighth, half, quarter. so on site we would write it down as 54-1F or 27-2L which is 54-3/16" and 27-5/16"
I like the way we can break down the on center layouts since there are 48" in plywood widths, we can do framing layouts with 6", 12", 19.2", 24" on center layouts. Metric can get to be a long string of numbers I would think. Are you guys calling out stuff in mm? like 1193mm?
That’s interesting.
Metric is pretty much in 10’s / 100’s and 1000’s
10mm to a cm or 1000mm to a meter Makes it easy to be precise
Very simple and easy but obviously it’s all about what your used to
Yea generally yell it out as millimeters. Like 2400mm. But instead of saying “two thousand four hundred”
We just say twenty four hundred or
2780mm would be Twenty seven eighty for example
….. if that makes sense
@@nomadnowhere1818 the problem there is you can't evenly divide. There are only 2 factors for a 10 based system making it impractical. In real world scenarios you just keep throwing away the excess so the numbers work out. In addition when it comes to vehicles and fasteners in particular there isn't a single system so many metric sets don't have a full complement of wrenches. I ran across that today with JIS metric on a tractor. If 10ths or the like get you excited you might be thrilled to know that machinists have been using them for a very long time without bothering with the metric system.
I'm not laughing AT you, I'm laughing WITH you, because I've made those same screwing mistakes. Love it!
Use 1 1/8" screws for 1/2" sheetrock and 1 1/4" for 5/8th" sheetrock. I agree with the rest of it. You can also get a guide tip router bit for your router and cut your sheets on your wider side and zip them in for a tight fit.
Drywall is fast, cheap, and slows fires down...
I'm no drywall expert, hence watching your good videos, but I like learning about the evolution of humans and their activities, Anthropology related.
Anyway, some centuries ago, Paris Burnt down pretty badly. Houses were built all out of lumber at the time, including wall finishes. It was noticed that houses that had the famous Plaster of Paris on their walls wouldn't burn as fast. So the king of France ordered all houses be built with plaster of Paris to help reduce fire spread. From plaster, we now have drywall boards because it's faster to put up on walls than plaster is. 😊 you can look into it and share the info in a future video, I might get to see. 😅
I have two of those "cheese-graters" (and have had them for a long time) and never knew that they were for drywall! I had thought that they were for wood and have tried using them many times but, not surprisingly, I was never very satisfied with what happened. Time to move them to the drywall tool box. :)
when they came out they were the sure-form rasp and were not particular to drywall. The idea was a rasp with a replaceable blade.
Only 3 mins into the video and already great advice thank you so much
That fact you do little mistakes in a simple mistake video goes with it and benefits the video so it's good either way
When you mentioned drywall not being a good product but it fast and cheap reminds of the British home improvement channels. They plaster their new walls and if they have 2 repair existing walls....those are replastered as well.
if you have someone hanging for you as you are laying out and cutting sheets you can mark screw layout with your t square on the sheet for accuracy especialy when your training a new guy.
this video has come too late for me. Watched many of your videos to learn as I went, as I was doing my reno and basically made most of the mistakes you mention. I'm afraid to watch your sequel to this. As they say "ignorance is bliss" at this point.. perhaps I don't want to know lol
As an electrical contractor, I do appreciate your pointing out to NOT overcut outlets. Watching your channel cause I am about to get messy with drywall at my own place. Hope I don't screw it up, well, screw it up in the wrong way!
Amazing videos. I'm just starting out getting my own Reno business going. You are by far my favorite. Very informative. I live on the Sunshine Coast in bc, so you being in Vancouver is pretty cool. Your videos are going to be my go-to for learning as I go. Thank you for your vids.👍
Awesome! Thank you!
Doing a big Reno in squamish and you are the go to when it comes to drywall.
G'day,
Kevin here from Australia.
I'm plastering a extension out (just the cornice to go now) and here we have to use stud adhesive when hanging plaster. You don't?
And I have studied your videos and I must say my plastering skills have improved outersight especially my external corners.
So thanks for sharing.
✌🏻 Peace
glue is available in North America but cannot always be used. Most times it is for added noise cancellation when laminating boards together. We use Vapor Barrier (Plastic) on the exterior walls in Canada as a moisture barrier and as such you cannot bond directly to the framing member. Internal walls are fine. I've started doing it for ceilings and is worth my extra effort cuts down on fastener holes too.
I used to teach drywall productivity....I could show you many tricks to save time and moves...
how about CODE LAW?
Or use a scrap piece of 1/2 inch on ground measure up to get center on outlet get 1 perfect cut use that scrap outlet piece to trace around
the drilling and screw fails were actually so entertaining and funny lol