I already built 4 different cases for my system because what they sell out there are not exactly what we need. My point is, I struggled a lot even on my last one after seen your video I found out easier ways for each application ... thanks for sharing your work!!👍👍
Your way of marking the handles with tape is brilliant. I've always had issues getting the hole marked just right under the latch, your way is such a great idea. Thanks!
A few things to note here. First and foremost, great work with this. It is an old school, single purpose design. If it gets busted, you build another... ...simple. For those who've criticized that, this case was designed to take the brunt of any fall, but only once or twice, as instruments and gear were not meant to be bounced around. If you want to build a similar project but with a more multi-use, bumping around purpose: 1. Instead of stapling ends first, use clamps to hold things together (bar clamps and standard trigger clamps work well, you'll need several to hold the box in shape), then start with one end, and move down the edge to the other end, stretching the sections into one another, excess can be shaved off with a sandeblock. 2. My dad and I both do this with anything we nail or staple--first we put wood glue on the edge, then we staple it, then remove the excess wood glue with a slightly dampened cloth or paper towel (not dripping, don't leave much moisture behind 3. One other "old school" method of creating these "boxes" is to cut square teeth on the ends of the boards, just over the width of the joining board, then use a cloth-hammer to "join" them, along with a staple and wood glue. Then you sand the excess off afterward. When stapling, you alternate around the angle, first on this side then on the other several teeth down. This leaves room for rivets\screws for edging, and if you stretch it down the line, rather than squeezing from the ends, any pressure on the box will "Relieve" the stretch, allowing it to absorb the impact more effectively. With teeth on both angles and stapling around the angle, you also have the added protection from an angular force, spreading the motion around the entire box instead of down just one side, which prevents the motion from transferring to your equipment. 4. To join the sides even more, and make the corners super solid, you can use corner steel pieces, inside and out, the outside being about the same thickness as your edging. Rounded corners are great because they allow you to stack the boxes and move around stacks without cutting yourself. This also lets you cut straight edging for several edges, and you can weld them together later to enable them to transfer force and move together. Some of that takes a lot more time, but if you are looking for a more permanent, and more beatable box, that'll do. Your time is worth something, so if you really want a durable box, you could always... ...eh.... ...purchase one, maybe? Once again, great job here. Just wanted to point out that it was great for the target purpose; workmanship and all. There's a logic to it all, and a kind of math that may not have perfect numbers, but it's still a sound bit of practice.
Thank you so much for your comment, I appreciated it very much, I am grateful to you because thanks to your opinions I have a great chance to improve in what I build. You said the right things and that make me think. As I said several times, before building I studied for almost two years gathering any information or advice from experts in the sector. For example, the professionals have advised me against the glue: the tightness of the FC (and its absorption of energy during its use) seems to be due to all the rest of the work, if it is done in a workmanlike manner, the glued parts they would make the FC less flexible causing a lower energy absorption (so they say), it must also be said that they are not designed to be waterproof or in general "eternal". I know that today there are better and lighter materials than multilayer, there are certainly much better techniques than mine, but I am only a beginner and what you see are my first works! Old school... I didn't care and I would never want to buy them new because I have the pleasure of making them with my own hands! (my channel is dedicated to DIY in general, wood, metal, etc). Building something with your own hands is the best thing there is :-) Thank you so much for your comment, I will take note of your info.
@@TheMusemush i like old school. Meant as a compliment. Old school craftsmanship here, built to last a while but be replaced readily (not perfectly instant, but easy enough) in case it meats an untimely incident (forget knocking, ill beat the pulp outta wood!). Loved your work here. Got ideas. You inspired. On your first shot. Good work.
On the upside, this way of building is great for hobby or light duty use. It's lighter weight and A LOT cheaper than using available extrusions everywhere and not having to back every rivet with a washer saves time, making the case cheaper as well. But using for example edge extrusions, as well as putting washers behind every rivet that anchors into wood, would make this case many times more solid. The construction shown in the video wouldn't have survived even a month in the light and sound equipment rental company I owned in the '90s - ask me how I know ... :-( We had a lot of cases fail that came with equipment and were built similar to the one here. There are a few things that would improve stability without adding too much cost or weight, but unfortunately would still add significant time, so depending on usecase may or may not be worth it.
I have repaired many of that style case, they are good until one takes a good hit or falls from a the truck. They mainly fail because the pop rivits pull through the wood (may not happen on first fall, but it loosens the rivit) my advise would be use a washer inside the box to sandwich the alum angle and the laminated wood together. Or use a Double Angle ALum Excursion, but they is more money have a slight design change. Good Luck!!!
Thank you so much for highlighting the hits according to your experience, I have a question Should we use washer on both side of revits or just inside the box? And what would be the thickness of plywood they've used in the video? And what type of double angle aluminum strip? They used L shape and what does the double angle looks like?
The key word is "passion", I always liked what I chose to do. Making FC is a job that requires good manual skills, tools, precision and passion, it must please: I had fun and I have a lot of fun building them! I hope these videos serve to make it clear that it is not an easy job, but neither impossible nor too difficult. Thanks for commenting. Regards
Amazing !! this is so inspiring, honestly I am your fan not just because of this case you made, also for this super clean system that you work, my respect for you man. Do you mind saying how much do you spend in the supplies you use building this beautiful case.
Hi GDN Records! I don't know exactly how much I spent, I bought the components in an online store, I know there are so many scattered all over the world, I looked for the closest one. Making it do it yourself you save a lot but there are very high chances of making mistakes and having to throw everything away if you don't have a bit of experience and tools. For more than a year I have studied from web sources and industry experts, it is an art to build cases! thanks a lot!
May I ask you what is the black kind of material on the surface? In one moment we can see a wooden ( plywood?) And next moment is black texturized material.
Awesome! I need to make a few custom FC's to protect a $195,000 camera, studio pedestal, camera head, and box lens. I will need to install custom plywood interior with foam and thin carpet material over it. You gave me and excellent method if doing this. Thanks!
Hello- Txs for sharing. Did you texturized the panels first or glue an ABS acrylic sheet to them? For the box structural rigidity did you only use brad nails? No screws?
The supplier sends me the panels already coated on one side. These types of FCs are made only with rivets, in the end the result is solid but also absorbs shocks, which would not happen if you glue and put screws, which means that it would be more at risk of breaking if it is subjected to heavy stresses such as falls accidental. Hi thank you very much
WOW i am impressed . I have some of the tools but i am missing the rivets tool and the saw table which is a major component to make sure the cuts are even. i might invest on purchasing those . I need multiple cases for my keyboards for p.a. speakers and more instruments i have. i think the investment will payoff by building my own cases. and who knows i might sale some to local bands . because we do not have any company in the area. EXCELLENT VIDEO.
mayhem-modz i pannelli di multistrato non li incollo mai, per incollaggi interni uso colla a contatto, quella che si applica su entrambi i pezzi da unire e si fa prima seccare bene.
You're damned right.. I had no other place to do my projects, so (not very happy) I used my home studio, trying to make as little dust as possible, then sucking everything I could during and after each step. Soon I will move house and I will be able to get a suitable place :-)
You have all the right tools, all the right materials/components, all the knowledge... and double speed camera with no explanations. It's impossible for average guys like us to make a case like this. Nice video, but useless for us.
Hi Minimoog7. Power tools simply allow you to speed up a job that you would do in much more time with hand tools. I don't agree that these videos are useless. Today compared to the nineties (when I started to need these FCs) we have the great opportunity to learn from the web and watching others, naturally on condition of wanting to learn, films like that for me and thousands of other people have been fundamental for begin to understand how something is made, the rest must also be studied. Before building I studied for years from all the YT films that I found, then I asked the professionals of the sector for advice: I was afraid of making a mistake (and I did well to wait). Unfortunately today we are used to pretending everything and immediately, all the solutions of crossword puzzles and puzzles, for this reason we often don't appreciate. Last thing, double speed camera is a technique that allows you to show lots of details that a normal speed movie wouldn't show. Thanks for commenting. Greetings.
There are aluminum parts that are mounted between the lid and the trunk, "Hybrid Lid location". If they are mounted in a workmanlike manner, they absolutely do not interfere with the work of the hinges. Greetings.
Complimenti per la realizzazione, flight case fatto molto bene e anche esteticamente ben rifinito. Vorrei chiederti qualche info in più su quello che hai usato: Il pannello di multistrato da quanto è? 15mm? Che vernice hai usato per pitturare la faccia esterna di nero? Che profili in alluminio hai usato per la parte di unione tra i due pezzi. Ho guardato sul sito suggerito in descrizione ma non ho ben capito quale hai usato. Sarebbe utile magari se aggiungessi anche le misure del flight case e anche quelle di cerniere e maniglie usate. Grazie mille. 🤟🏻😉
Buonasera! Multistrato di betulla già rivestito da un lato, spessore 7mm, oltre diventa troppo pesante ed ingestibile e questo spessore si è rivelato più che sufficiente per ciò che dovevo fare io. I FC non hanno degli standard, se vuoi realizzarne uno è un pò come quando vai al supermercato: in base al piatto che devi fare sceglierai i tuoi ingredienti, per quello non ha senso riprodurre le stesse misure, perchè l'ho progettato (insieme alla suddivisione degli spazi) in base a quello che dovevo contenere. Il sito in descrizione ha anche un recapito telefonico, contattali sono molto disponibili e ti guideranno per capire quale hardware acquistare. Grazie mille e buona realizzazione!
@@TheMusemush grazie mille, sei stato gentilissimo e il tuo video mi ha fornito molti spunti. Ho già fatto una "lista della spesa" dal sito che hai consigliato, che tra l'altro ha dei buoni prezzi. Sicuramente proverò a contattarli! ;)
excellent work, very clean technique!!, What kind of wood did you use? Or does somebody know what kind of wood could I use to do a similar flight case?
Great video! Thanks for sharing! I just have one question: How did you fit the little "rails" that hold the dividing walls in place? Are these just glued in? Thank you
Hi, excellent video, what is the material that you use in the inside walls of the case ? How can I found it on the market? Can you suggest any link ? Thanks
Hello Friend, I designed this FC to transport without destroying the necessary equipment for my concerts. I don't always put the same things inside but generally they are high quality audio cables, microphones, electrical part and spare mixer. Transport by car decreases the life of whatever equipment you need, and this is why these special containers are made. Thanks so much
There is not a type of multilayer suitable for all projects, it depending on what is used. For latest work I posted I used 7mm birch plywood, coated on one side in pvc. On the web there are a lot of sites that are right for you.
Hello very interesting, one question which plywood you used for this Flight Case I mean for one side is black for another side natural or do you used some melamine? thanks ;)
Hi Joseph. When making these videos, try to summarize the processing steps, otherwise they become long and boring! I promise to be more detailed in the next. Thank you so much
3/16" diameter. The box of rivets will also have a 'grip' spec. which denotes a nominal length after installation (in my experience this variable takes account for a backing washer as well). So, a 1/4" grip rivet will work for attaching extrusions to 1/4"-thick panels, but you'll usually also need other rivets with a longer grip for attaching hardware spanning the extrusions (latches in particular).
Nice build. But doesn't seem like anything really custom here, so would probably just be cheaper to buy one. If it was to hold specific series of equipment and custom made to fit them it would make more sense to build.
Hayden Young I designed all my F.C. in autocad according to my needs, if I had to hire a designer and have it done, it would have cost a lot more (I tell you because in the past I paid them a lot of money). those that are cheap have also tried them and they have lasted me very little. Then if you don't like them I understand, they can't please all my modest cases ... :-)
@@TheMusemush yeah I was just referring to the fact you only used it for cables. Something all F.C can do. If it was for specific gear and made to those sizes i would understand the need to custom make. Its a good build none the less tho.
I can't tell you how much I spent, I had things already in the lab, others I bought. I worked there in the spare time I could find. thank you very much.
For all the FCs you see in this channel I used 7mm birch plywood, coated on one side with specific pvc. I also used the same plywood for the FC of the 34kg fender amp, so I guess you can use it for a 15kg object .... The choice of thickness also depends on the project. Greetings
I bought the hardware in a specialized store in my country, I only took the plywood panels and the rivets online, but I see that there are so many sites that sell hardware online.. I suggest you look for the one closest to your country.
@@TheMusemush thank you for your reply, I'm not sure what to look for or the names of the hardware but I'll try. what are the names of the type of latches or locks that you used? and the type of hinges, what might they be called? I hope that made sense 😊
@@WiKiTWoNKa I advise you not to venture immediately into the realization of FC, it is an art, it is a job and consequently it is a bit difficult to work on it right away. The chances of making millimeter errors that force you to throw everything in the middle of the job are high if you don't know what to do, not just watching videos as fast as mine, give yourself a reasonable time to study what materials it is composed of and the processing phases. One of the most important things: make sure you also have the right tools. I suggest you take a look at this page: www.flightcase-brico.com/en/content/6-general-flight-case-assembly-instructions
@@TheMusemush Thank you and as you don't know me personally you gave me the advice as a good gesture and greatly appreciated... I have been building speaker enclosures and also cabinetmaking since I was a teenager, I am 44 now and have wood working tools and want to get in to this type of work but for now only for my music equipment and then when I get confident enough that my work hasn't fell apart and stood through the test of time then I may build as a career but for now if you can guide me to where I can find the hardware that you used or just tell me the names of the hardware then I will look it up on my own please 🙏🏽
Hallo. Zum Schneiden von Sperrholzplatten (in diesem Fall Birke) verwende ich nur die CMT-Klinge mit 80 Zähnen, langsamer, aber extrem sauberer Schnitt.
I used the specific hardware for Flight Case: aluminum extrusions, corner profiles, corner reinforcements, butterfly closures. You can find all this material on the website of my supplier: www.smithandsons.it
I already built 4 different cases for my system because what they sell out there are not exactly what we need. My point is, I struggled a lot even on my last one after seen your video I found out easier ways for each application ... thanks for sharing your work!!👍👍
Your way of marking the handles with tape is brilliant. I've always had issues getting the hole marked just right under the latch, your way is such a great idea. Thanks!
A few things to note here. First and foremost, great work with this. It is an old school, single purpose design. If it gets busted, you build another... ...simple.
For those who've criticized that, this case was designed to take the brunt of any fall, but only once or twice, as instruments and gear were not meant to be bounced around.
If you want to build a similar project but with a more multi-use, bumping around purpose:
1. Instead of stapling ends first, use clamps to hold things together (bar clamps and standard trigger clamps work well, you'll need several to hold the box in shape), then start with one end, and move down the edge to the other end, stretching the sections into one another, excess can be shaved off with a sandeblock.
2. My dad and I both do this with anything we nail or staple--first we put wood glue on the edge, then we staple it, then remove the excess wood glue with a slightly dampened cloth or paper towel (not dripping, don't leave much moisture behind
3. One other "old school" method of creating these "boxes" is to cut square teeth on the ends of the boards, just over the width of the joining board, then use a cloth-hammer to "join" them, along with a staple and wood glue. Then you sand the excess off afterward. When stapling, you alternate around the angle, first on this side then on the other several teeth down. This leaves room for rivets\screws for edging, and if you stretch it down the line, rather than squeezing from the ends, any pressure on the box will "Relieve" the stretch, allowing it to absorb the impact more effectively. With teeth on both angles and stapling around the angle, you also have the added protection from an angular force, spreading the motion around the entire box instead of down just one side, which prevents the motion from transferring to your equipment.
4. To join the sides even more, and make the corners super solid, you can use corner steel pieces, inside and out, the outside being about the same thickness as your edging. Rounded corners are great because they allow you to stack the boxes and move around stacks without cutting yourself. This also lets you cut straight edging for several edges, and you can weld them together later to enable them to transfer force and move together.
Some of that takes a lot more time, but if you are looking for a more permanent, and more beatable box, that'll do. Your time is worth something, so if you really want a durable box, you could always... ...eh.... ...purchase one, maybe?
Once again, great job here. Just wanted to point out that it was great for the target purpose; workmanship and all. There's a logic to it all, and a kind of math that may not have perfect numbers, but it's still a sound bit of practice.
Thank you so much for your comment, I appreciated it very much, I am grateful to you because thanks to your opinions I have a great chance to improve in what I build.
You said the right things and that make me think.
As I said several times, before building I studied for almost two years gathering any information or advice from experts in the sector.
For example, the professionals have advised me against the glue: the tightness of the FC (and its absorption of energy during its use) seems to be due to all the rest of the work, if it is done in a workmanlike manner, the glued parts they would make the FC less flexible causing a lower energy absorption (so they say), it must also be said that they are not designed to be waterproof or in general "eternal".
I know that today there are better and lighter materials than multilayer, there are certainly much better techniques than mine, but I am only a beginner and what you see are my first works!
Old school... I didn't care and I would never want to buy them new because I have the pleasure of making them with my own hands! (my channel is dedicated to DIY in general, wood, metal, etc). Building something with your own hands is the best thing there is :-)
Thank you so much for your comment, I will take note of your info.
@@TheMusemush i like old school. Meant as a compliment. Old school craftsmanship here, built to last a while but be replaced readily (not perfectly instant, but easy enough) in case it meats an untimely incident (forget knocking, ill beat the pulp outta wood!). Loved your work here. Got ideas. You inspired. On your first shot. Good work.
On the upside, this way of building is great for hobby or light duty use. It's lighter weight and A LOT cheaper than using available extrusions everywhere and not having to back every rivet with a washer saves time, making the case cheaper as well.
But using for example edge extrusions, as well as putting washers behind every rivet that anchors into wood, would make this case many times more solid. The construction shown in the video wouldn't have survived even a month in the light and sound equipment rental company I owned in the '90s - ask me how I know ... :-( We had a lot of cases fail that came with equipment and were built similar to the one here. There are a few things that would improve stability without adding too much cost or weight, but unfortunately would still add significant time, so depending on usecase may or may not be worth it.
I have repaired many of that style case, they are good until one takes a good hit or falls from a the truck. They mainly fail because the pop rivits pull through the wood (may not happen on first fall, but it loosens the rivit) my advise would be use a washer inside the box to sandwich the alum angle and the laminated wood together. Or use a Double Angle ALum Excursion, but they is more money have a slight design change. Good Luck!!!
good tip. I was just thinking 'Is he just riviting direct into the wood?' Thats going to come loose
Thank you so much for highlighting the hits according to your experience, I have a question Should we use washer on both side of revits or just inside the box? And what would be the thickness of plywood they've used in the video?
And what type of double angle aluminum strip? They used L shape and what does the double angle looks like?
i use to make cases . it is advisable to put small washers behind the rivits , in time fittings work loose
@@ranasaab6560 use washers inside only....tongue and groove instead of angled aluminum in between
Now I dont feel bad spending several hundreds on the cases. What an effort to build one. Good job
The key word is "passion", I always liked what I chose to do. Making FC is a job that requires good manual skills, tools, precision and passion, it must please: I had fun and I have a lot of fun building them! I hope these videos serve to make it clear that it is not an easy job, but neither impossible nor too difficult. Thanks for commenting. Regards
Amazing !! this is so inspiring, honestly I am your fan not just because of this case you made, also for this super clean system that you work, my respect for you man. Do you mind saying how much do you spend in the supplies you use building this beautiful case.
Hi GDN Records!
I don't know exactly how much I spent, I bought the components in an online store, I know there are so many scattered all over the world, I looked for the closest one. Making it do it yourself you save a lot but there are very high chances of making mistakes and having to throw everything away if you don't have a bit of experience and tools. For more than a year I have studied from web sources and industry experts, it is an art to build cases!
thanks a lot!
May I ask you what is the black kind of material on the surface? In one moment we can see a wooden ( plywood?) And next moment is black texturized material.
@@robertchytil1 ABS Plastic is normally used for road cases. It is glued onto the plywood.
Excelente trabalho. Isso estimula outras pessoas a fazerem seus próprios cases. Parabéns!
Alguem sabe o nome das rodinhas q ele colocou ???
Very nice video of the process. Some great ideas in the fabrication as well!
Thank you for the inspirational education. I would love to see you build a flight case for a cello... given the varying depth of the instrument.
Awesome! I need to make a few custom FC's to protect a $195,000 camera, studio pedestal, camera head, and box lens. I will need to install custom plywood interior with foam and thin carpet material over it.
You gave me and excellent method if doing this. Thanks!
Algún curso que haya en español !? Es un trabajo agradable y muy eficiente para la protección de los equipos.
Beautiful case!!!
Hello- Txs for sharing. Did you texturized the panels first or glue an ABS acrylic sheet to them? For the box structural rigidity did you only use brad nails? No screws?
The supplier sends me the panels already coated on one side. These types of FCs are made only with rivets, in the end the result is solid but also absorbs shocks, which would not happen if you glue and put screws, which means that it would be more at risk of breaking if it is subjected to heavy stresses such as falls accidental. Hi thank you very much
Very interesting video, we wondered how a flight case is made. Maybe someday we will make some for our gear, they are expensive to buy.
excelente!! el mejor video que he visto hasta al momento, gracias!!! saludos.
-amazing work !! in such a small room. Great Job Man 🙂
fixing the whole box together before cutting off the lid....genius!
Different techniques can be used based on the characteristics that the FC must have.
WOW i am impressed .
I have some of the tools but i am missing the rivets tool and the saw table
which is a major component to make sure the cuts are even.
i might invest on purchasing those .
I need multiple cases for my keyboards for p.a. speakers and more instruments i have.
i think the investment will payoff by building my own cases.
and who knows i might sale some to local bands . because we do not have any company in the area.
EXCELLENT VIDEO.
Uses blade cover and riving knife! Instant like for safe work.
yes, but that unbalanced cut at 0:06...
Nice job! Liked the pneumatic riveter! 👍
It's a Mannesmann, paid less than 100 €, for this price range they are all the same.
The Surge Party Band NJ If you happen to be in the building trades Milwaukee makes a Cordless Rivet Gun.
Some links to where you bought the end metal pieces for your case. Or a source for the handles and latches would be great
You can find the link in the description
Love the little demo on vibrato! Helped heaps!
Thanks 🙏🏼 from Malaysia
Que video tan entretenido y dador de ideas. Felicidades
bravo pour cette belle fabrication et le son est top ;-) bravo per questa bellissima produzione e il suono è ottimo ;-)
Fantastic job man!!! Many thanks for sharing the vid. How many days took you to build the flightcase? cheers!
2-3 days in my free time... Without a workshop it is so hard! Thank you so much
Cool!!!
Very nice equipments u'hv got
Is the plywood pre-laminated, or do you laminate it beforehand? Unless it has a different coating?
Pre-laminated
I thought this would be some cool modular case or something similar .
Wow, you make it look so easy to make a case. Do you take orders, and do you ship?
This is an excellent video! You are a very good fabricator. May I ask where you got the different parts?
You can find the link in the description
I have a problem with my homemade flight case which glue do you use? thanks
mayhem-modz i pannelli di multistrato non li incollo mai, per incollaggi interni uso colla a contatto, quella che si applica su entrambi i pezzi da unire e si fa prima seccare bene.
What kind of rivets would one use for 5/8 thick material? Thanks.
Well done! I'm not sure doing carpentry in the same room where you keep your instruments and computer is such a good idea, though! LOL.
You're damned right.. I had no other place to do my projects, so (not very happy) I used my home studio, trying to make as little dust as possible, then sucking everything I could during and after each step. Soon I will move house and I will be able to get a suitable place :-)
You have all the right tools, all the right materials/components, all the knowledge... and double speed camera with no explanations. It's impossible for average guys like us to make a case like this. Nice video, but useless for us.
Hi Minimoog7.
Power tools simply allow you to speed up a job that you would do in much more time with hand tools.
I don't agree that these videos are useless. Today compared to the nineties (when I started to need these FCs) we have the great opportunity to learn from the web and watching others, naturally on condition of wanting to learn, films like that for me and thousands of other people have been fundamental for begin to understand how something is made, the rest must also be studied. Before building I studied for years from all the YT films that I found, then I asked the professionals of the sector for advice: I was afraid of making a mistake (and I did well to wait). Unfortunately today we are used to pretending everything and immediately, all the solutions of crossword puzzles and puzzles, for this reason we often don't appreciate.
Last thing, double speed camera is a technique that allows you to show lots of details that a normal speed movie wouldn't show.
Thanks for commenting. Greetings.
Very good work
Congratulations
This is what I would love to do...great!
meraviglioso!! Bravissimo!!!
very helpful thank you👍
Excellent video! Thank you!
Very nice work 👍🖖
Great video !
Regarding the aluminium profile you use for the opening part, it's a male/female one ? There is no issue of friction on the hinge side ?
There are aluminum parts that are mounted between the lid and the trunk, "Hybrid Lid location". If they are mounted in a workmanlike manner, they absolutely do not interfere with the work of the hinges. Greetings.
Complimenti per la realizzazione, flight case fatto molto bene e anche esteticamente ben rifinito. Vorrei chiederti qualche info in più su quello che hai usato:
Il pannello di multistrato da quanto è? 15mm?
Che vernice hai usato per pitturare la faccia esterna di nero?
Che profili in alluminio hai usato per la parte di unione tra i due pezzi. Ho guardato sul sito suggerito in descrizione ma non ho ben capito quale hai usato.
Sarebbe utile magari se aggiungessi anche le misure del flight case e anche quelle di cerniere e maniglie usate.
Grazie mille. 🤟🏻😉
Buonasera!
Multistrato di betulla già rivestito da un lato, spessore 7mm, oltre diventa troppo pesante ed ingestibile e questo spessore si è rivelato più che sufficiente per ciò che dovevo fare io.
I FC non hanno degli standard, se vuoi realizzarne uno è un pò come quando vai al supermercato: in base al piatto che devi fare sceglierai i tuoi ingredienti, per quello non ha senso riprodurre le stesse misure, perchè l'ho progettato (insieme alla suddivisione degli spazi) in base a quello che dovevo contenere. Il sito in descrizione ha anche un recapito telefonico, contattali sono molto disponibili e ti guideranno per capire quale hardware acquistare. Grazie mille e buona realizzazione!
@@TheMusemush grazie mille, sei stato gentilissimo e il tuo video mi ha fornito molti spunti. Ho già fatto una "lista della spesa" dal sito che hai consigliato, che tra l'altro ha dei buoni prezzi. Sicuramente proverò a contattarli! ;)
Beautiful job bro
Nice work man!
Sem palavras para descrever meu espanto! Sensacional. Parabéns!
Alguem sabe o nome das rodinhas q ele colocou ???
TOP ..... SHOW ..... 10 ..... PARABENS !!!! .... 5 STAR !!!!!
nice clean work!
excellent work, very clean technique!!, What kind of wood did you use? Or does somebody know what kind of wood could I use to do a similar flight case?
You must use plywood panels, the thickness must be chosen based on the work you need to do. I didn't go beyond 7mm.
Hermoso trabajo!!!!!
👏👏👏👏👏👏👏👏
I like the way you made the lit of the box, very smart.
Riny van Abel Thank’s 🙏🏻
Great video! Thanks for sharing!
I just have one question: How did you fit the little "rails" that hold the dividing walls in place? Are these just glued in? Thank you
Yes exactly, glued in. A simple and effective solution. Thanks so much
Well done!!!
Do you get the timber already with the black on it? If so whats it called?
7mm birch plywood. In description you can find the link of my supplier.
Hi, excellent video, what is the material that you use in the inside walls of the case ? How can I found it on the market? Can you suggest any link ? Thanks
Hi can you send me a link for trays that holds the spacers :) thank you
nice bro , good job.
great video really enjoyed it your very good making flight cases. I hope you didn't do all that just for some cables and a power strip lol
Hello Friend,
I designed this FC to transport without destroying the necessary equipment for my concerts. I don't always put the same things inside but generally they are high quality audio cables, microphones, electrical part and spare mixer. Transport by car decreases the life of whatever equipment you need, and this is why these special containers are made.
Thanks so much
Where can i find that kind of plywood already black one side. Lowe's and homedipot they don't or name of the plywood for searching on internet
There is not a type of multilayer suitable for all projects, it depending on what is used. For latest work I posted I used 7mm birch plywood, coated on one side in pvc. On the web there are a lot of sites that are right for you.
Top top demais amigo um show de sucesso parabéns
Great job
Hello very interesting, one question which plywood you used for this Flight Case I mean for one side is black for another side natural or do you used some melamine?
thanks ;)
Hi. I purchased 1x1 PVC-coated panels
Really amazing work
This is cool, but can you do a step by step walk through with descriptions of each component?
Hi Joseph. When making these videos, try to summarize the processing steps, otherwise they become long and boring!
I promise to be more detailed in the next. Thank you so much
Nicely done!
Great work!
Un gran like 👍🏼
it is very impressive !! Congratulations.
Andres Padrón Thanks 🙏🏻
Where do you buy your parts exactly? I'm looking to build a custom case for my needs and cant seem to find the parts.
Do a search for flight case parts. There are several suppliers.
What do you need a case for? Your buttplugs????
Geoff Marsted www.smithandsons.com
Yo trabajé varios años en Boston mass en s&m trunk y los hacía esos en diferentes colores y otros modelos
Magnifico!
Question - what size rivets do you use if you are putting latches on 1/4" laminated plywood?
3/16" diameter. The box of rivets will also have a 'grip' spec. which denotes a nominal length after installation (in my experience this variable takes account for a backing washer as well). So, a 1/4" grip rivet will work for attaching extrusions to 1/4"-thick panels, but you'll usually also need other rivets with a longer grip for attaching hardware spanning the extrusions (latches in particular).
What thickness of plywood you've used?
You must use plywood panels, the thickness must be chosen based on the work you need to do. I didn't go beyond 7mm
@@TheMusemush thank you soooo much I really appreciate your response
Amazing! Do you make custom cases for other people?
Hi Aaron, thank you very much! No, I build for myself when I need it, sorry.
Nice job!
Omg this is awesome
A GREAT JOB
Brilliant very well done
Nice build. But doesn't seem like anything really custom here, so would probably just be cheaper to buy one. If it was to hold specific series of equipment and custom made to fit them it would make more sense to build.
Hayden Young
I designed all my F.C. in autocad according to my needs, if I had to hire a designer and have it done, it would have cost a lot more (I tell you because in the past I paid them a lot of money). those that are cheap have also tried them and they have lasted me very little. Then if you don't like them I understand, they can't please all my modest cases ... :-)
@@TheMusemush yeah I was just referring to the fact you only used it for cables. Something all F.C can do. If it was for specific gear and made to those sizes i would understand the need to custom make. Its a good build none the less tho.
Nice job brother
awesome job !! where did you get the aluminum for the edges ?
Link in description
Congrats... looks great!
how much did you spend, and how many hours of work
I can't tell you how much I spent, I had things already in the lab, others I bought. I worked there in the spare time I could find. thank you very much.
Perfect!
Nicely done
this video needs some public domain classical music. like a dance.
1/4” construction? What was the final empty weight?
I didn't weigh it empty sorry
What kind of wood is this? It has an interesting texture. Can it hold 15 kilograms? Could you recommend a wood that can handle 15 kilograms?
For all the FCs you see in this channel I used 7mm birch plywood, coated on one side with specific pvc. I also used the same plywood for the FC of the 34kg fender amp, so I guess you can use it for a 15kg object .... The choice of thickness also depends on the project. Greetings
Bravo travaille de prof
What model is that rivet gun?
Nice video ..now is time do my case
Thank's. I wish you good work then, let me know when it's over.
Good job 🤘
🙌👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏🖖
Will you please put links to where you found your hardware for the case? Thank you kindly 👍
I bought the hardware in a specialized store in my country, I only took the plywood panels and the rivets online, but I see that there are so many sites that sell hardware online.. I suggest you look for the one closest to your country.
@@TheMusemush thank you for your reply, I'm not sure what to look for or the names of the hardware but I'll try. what are the names of the type of latches or locks that you used? and the type of hinges, what might they be called? I hope that made sense 😊
@@WiKiTWoNKa
I advise you not to venture immediately into the realization of FC, it is an art, it is a job and consequently it is a bit difficult to work on it right away. The chances of making millimeter errors that force you to throw everything in the middle of the job are high if you don't know what to do, not just watching videos as fast as mine, give yourself a reasonable time to study what materials it is composed of and the processing phases. One of the most important things: make sure you also have the right tools. I suggest you take a look at this page:
www.flightcase-brico.com/en/content/6-general-flight-case-assembly-instructions
@@TheMusemush Thank you and as you don't know me personally you gave me the advice as a good gesture and greatly appreciated... I have been building speaker enclosures and also cabinetmaking since I was a teenager, I am 44 now and have wood working tools and want to get in to this type of work but for now only for my music equipment and then when I get confident enough that my work hasn't fell apart and stood through the test of time then I may build as a career but for now if you can guide me to where I can find the hardware that you used or just tell me the names of the hardware then I will look it up on my own please 🙏🏽
@@TheMusemush also thank you for the link that is a big help
Where do you get the aluminum and what's the plywood size?
You can find the link in the description
Nice!
Wie stark ist deine blatte und welches Holz/blatte verwendest du?
Hallo. Zum Schneiden von Sperrholzplatten (in diesem Fall Birke) verwende ich nur die CMT-Klinge mit 80 Zähnen, langsamer, aber extrem sauberer Schnitt.
@@TheMusemush danke und wie stark ist das Holz was du /sie verwendet haben?
what was the aluminum called that you used for the box to close on?
I used the specific hardware for Flight Case: aluminum extrusions, corner profiles, corner reinforcements, butterfly closures. You can find all this material on the website of my supplier: www.smithandsons.it
Wow 💪💪💪💪👍👍👍👍👍👍👍👍from indonesia
Hola, que madera se utiliza?
Contrachapado de abedul de 7 mm
Sensacional ⚡🔥🔥👏🏻👏🏻💪🏻❤️
Do you sell custom cases ? For example how much would the case you built here be to purchase ? Great work.
No, I built them for myself but it's not a job. Thanks