@@williamrivera4878 hi! Depends on what you are building. If it's bridgeported, get a 600 with mechanical secondaries. It's going to need tuning. The ones from racing beat come super close to what you will need, but still will need tuning.
Heck I have a question, I picked up an rx8 with a bunch of issues I’m thinking about getting like a s4 13b bridgeport and putting a carb on it? Would you recommend a holley carb?
@@ImpalerRotary just limped a 12a (with I believe a rb holley kit) home. Pressure was at like 9 psi! I remember stock was like 4.5 and webers were too. Po said it had to be higher, but 9 I was way high.
A 600 works really good. A 650 is good also but requires more tuning to make it work. The one in the video is a 650 and the engine is a 12a bridgeport.
@@ImpalerRotary @ImpalerVlad just got around to rebuilding my carb(600 street warrior) po had 72s in there and a the power valve was a plugged. On a 12a bridgeport (I believe)
Thanks I would love to see more videos on tuning and special timing with bridge port video was great haven’t seen a holley work that good in a while
Thank you! I'll try and get a few more in, specially on timing.
@@ImpalerRotary I'm looking into a new holley what do recommend for easy tuning I see mechanical secondary vacuum thanks for the help
@@williamrivera4878 hi! Depends on what you are building. If it's bridgeported, get a 600 with mechanical secondaries. It's going to need tuning. The ones from racing beat come super close to what you will need, but still will need tuning.
@@ImpalerRotary thanks I'm going to order the one but tunning a holley it's not easy
MECHANICAL SECONDARY
650 CFM Brawler Diecast Carburetor Mechanical Secondary / Electric Choke
PART# BR-67276
Would this work
Nice a i love rotary i have rotarys down here in the island puerto rico
what are the parts needed to installed a Holley brawler 650 I have the carburetor itself and the racing beat intake manifold
I have a 13b with carburetor but I’m not getting much gas in the carburetor any idea what it could be idk if the carburetor needs tuning or something
Probably needs to be tuned. Make sure the needles on the side are open enough for fuel to come in.
Heck I have a question, I picked up an rx8 with a bunch of issues I’m thinking about getting like a s4 13b bridgeport and putting a carb on it? Would you recommend a holley carb?
Sorry for the delay. Lots of folks are doing similar swaps.
How do you monitor af ratio on these cars for tuning? Wide band?
I ordered a 600CFM Street Warrior For my 13B
hey where are you located ,
@@luispagan-ru2xo North Carolina
Can I run a Holley 600 on a stock 12a with 54 Jets or what do you recommend?!
Yes, that's close to what it needs.
@@ImpalerRotary I have a stock port 12a and the previous owner put a holley 650 on it. What jet size do you recommend? I'm new to carbs.
@@JetJiles Id start with 60 primary and secondary. Go up by 2s from there, so 62, 64, etc.
@@ImpalerRotary ok thank you for the help!
@@JetJiles Sure thing! You can follow me on IG @xrossfire78 or TikTok @impalervlad.
Is there any way i can get in contact with you? I also have the same setup im looking for some tips
I'm in instagram as xrossfire78 and Tiktok as impalervlad
Hi do you have the msd boxes set up in 6 cylinder?
I believe he cut the purple cable that the instructions told him to. I'm not sure if that is what you are referring to.
No im referring to the ignition setting on the box. 4 cylinder, 6 and 8. I think most use 6 cylinder. If he does then I will too
Lol oh he is you, thanks for the reply.
I'll double check today.
@@ImpalerRotary thank you man for your time
What the fuel pressure?
6psi
@@ImpalerRotary just limped a 12a (with I believe a rb holley kit) home. Pressure was at like 9 psi! I remember stock was like 4.5 and webers were too. Po said it had to be higher, but 9 I was way high.
What regulator is that?
@@josephfriedrich9792 Holley regulator.
@@josephfriedrich9792 Yeah 9 is quite high.
I want to carb an RX-8 engine for a REPU.......
What carb do you recommend for 12a full bridge port
A 600 works really good. A 650 is good also but requires more tuning to make it work. The one in the video is a 650 and the engine is a 12a bridgeport.
@@ImpalerRotary @ImpalerVlad just got around to rebuilding my carb(600 street warrior) po had 72s in there and a the power valve was a plugged.
On a 12a bridgeport (I believe)
Tie those omp lines up with a zip line . Don't want to run the rotor dry
We are pre-mixing just in case.
I've never seen a carbed rotary
This is the old school method.
Bin the Holley and put a Weber on it