Hi Michaels camera am facing some issues with my Blackmagic ATEM Television Studio HD as the screen i connect to the ATEM MulitVIEW pot is not showing and image but the ATEM LCD screen is showing image from a camera I connect to it.
Edenilson Cardoso YES unfortunately it was a defective Switcher. So I sent it to BM and they wound up sending me a new one. Everything worked fine. You’ll have to email BM.
Great Video! Actually i use the BlackMagic Web Presenter for Livestream a Talk. I have a question. Can you say a little bit more about the two XLR-Mic Inputs? On The Web Presenter you only have on XLR Mic Input. Thanks!
The first was connecting the blackmagic design software to the micbook air. Once again installed on another window laptop and connected. Then the first laptop (mickbook air) was disconnected. What to do to connect again.
Thanks for the video! I'm looking to send my program output to a projector (using SDI-HDMI conversion) and then want to send a different output to another projector (using another SDI-HDMI converter). For the output through an aux, can I select the aux and mix video inputs in the same way as the program out? Or even get a multiview that will show Preview and Aux rather than Preview and Program, but be able to switch between where I'm mixing to?
HI thanks for the info. Got my cams connected. Activity on the audio meters, but no pic on thumbnails, just black. Same cams, same settings when connected to Web Presenter look good, but black on ATEM. Thank you
Hey, great video, very clear, thanks a lot! Question, do I need a video capture card to input to my pc? does it have a usb3 cable to directly send output to my pc?
Please help! I have a dslr t7i running 1080p29.89 FPS. It seems to not be connecting to the ATEM, even if I change the FPS in both sources, ATEM and camera
Hello, I have just received my Black Magic HDMI to SDI and running into my Black Magic Web Broadcaster to my iMac thorough OBS. The Picture is barely visible and lines all along the scene as well it is also show the same in the web broadcasters lcd panel. If I just connect from my canon camera to the web broadcaster via HDMI it works perfect. Any ideas on what to do? Thanks in advance.
I'm not sure if you're still picking these comments up, but when you said you can run two separate multicams out (one SDI, one HDMI) did you mean they can be configured separately or are they just a cloned output? Also do you think it's worth getting a loom made up for the long runs of cables for SDI or does that limit your camera placements?
we have found out that unless your camera can output a mono signal onto both channels the ATEM television studio HD is no good for audio unless you use a separate mixer. The audio signals are linked stereo on the ATEM which means if you only have one microphone plugged in it will be permantly panned hard left or hard right and there is no way to change this position unless you use the more expensive 4K version of the system.
블랙매직디자인 스위쳐 ATEM Television Studio HD 믹서에서 카메라신호와 마이크 신호 받아서 프리뷰로햐서 자막기에서들어가서 hdmi해서 캡처보드 보냐는대요. 믹서에서 멀티뷰 말고 출력단자가 4개sdi단자있는대 바로 출력하면 자막기에서 자막 입혀서 나가서 캡처보드 / 자마막기에서 자막 입혀서 믹서에 4개 sdi 단자로 출력 가능할까요?
Hi there, having this can you please tell me WHERE TO RECORD our program output.? Only on cameras..? Or where to record to the final product.? please describe
When I connect my 2 cameras the switch doesn't get the video signals and instead of it only shows me a black screen and gets the audio. I'm trying to record 1080p signals in 29,97fps I REALLY hope you can help me. Thanks
Make sure that you match the resolution of those two camera hope those cameras are the same MAKE and MODEL and then set the same resolution on the ATEM and that should work.
i all i need to know wy black magic dont have a support on line? i have the same type of atem television studio hd but i need to use it like video mixer it must manage all video resssource .so when i connect video by sdi port it dont print it macthing only from hdmi port ;could you assit me to setup pleaze advencing think s
I would have loved to see a connection of the Camera and Laptop/pc input. I seem to be having challenges with getting a laptop signal to the mixer. Could you kindly advice on what I could be doing wrong?
The important thing to remember when Switching Cameras and Computers is to have everything on the same standard - in 99% of cases this means 1080p60. If you can't get all sources on the same standard you might need to convert the problem signal to match your main standard. For this job you want to get a Blackmagic Teranex AV into your system. Check out this video: ua-cam.com/video/ed8BbhWJ6g8/v-deo.html
Michael, you can record the streaming output with any standard application that can record from a web cam. Do keep in mind that this will be at 720p. Otherwise you will need a video capture card with HDMI or SDI inputs. The way we record is with a standalone Blackmagic Hyperdeck. There SSD and SD versions of these Hyperdecks. Very nice products.
The ATEM does the Video Switching, to stream you will just send the output from the ATEM to the Blackmagic Web Presenter. Check out this video: ua-cam.com/video/TFzFAZLSu_Y/v-deo.html
Hi, I'm liking your video, but what if I don't wanna use the web presenter can I just input the signal with declink (or something similar) - and then use other software to stream it? Do you have a video how the ATEM control software works in this kind of situation? The goal that I'm trying to create is a streaming solution for 2 or more cameras that would require only one laptop that would do both the live editing and streaming.
The ATEM control software is completely independent of your method of streaming. As long as you can capture the video output from the ATEM into your computer (or even a stand alone streaming device) and get it to a streaming application you should be good to go. Keep in mind you don't need to do the live switching from the ATEM software as the basic controls are on the front panel of the ATEM. The other software items (like OBS Studio) just run in the background on the computer once you set them up and go live.
You are correct, the Web Presenter's output is a Web Camera feed over USB to a computer. The beauty of this system is any software you like can take a Web Camera feed.
ya sabemos que no podemos recomendar el equipo, de ahora en adelante cuando me pregunten en santo domingo, republica dominicana por los productos de blackmagie le dire no lo compren que tienen problemas de carga no tiene protecion y mas no tiene reparacion en santo domingo y estados unidos....LES DIRE NO LO COMPREN TIENEN PROBLEMAS DE VOLTAJES
simple and straight to the point explanation. thank you
Best video out there about this product, thank you
very good video Michael!
Faaaaaantastic video!!! Thank you!!!
Excellent video, informative and very nicely conducted
Hi Michaels camera am facing some issues with my Blackmagic ATEM Television Studio HD as the screen i connect to the ATEM MulitVIEW pot is not showing and image but the ATEM LCD screen is showing image from a camera I connect to it.
Did you figure this out? Having the same issue!
Were you able to solve the problem? I have the same problem. Can you help me.
@@timothycyphers4734 Were you able to solve the problem? I have the same problem. Can you help me.
Edenilson Cardoso YES unfortunately it was a defective Switcher. So I sent it to BM and they wound up sending me a new one. Everything worked fine. You’ll have to email BM.
Great Video! Actually i use the BlackMagic Web Presenter for Livestream a Talk. I have a question. Can you say a little bit more about the two XLR-Mic Inputs? On The Web Presenter you only have on XLR Mic Input. Thanks!
The first was connecting the blackmagic design software to the micbook air. Once again installed on another window laptop and connected. Then the first laptop (mickbook air) was disconnected. What to do to connect again.
Thanks for the video!
I'm looking to send my program output to a projector (using SDI-HDMI conversion) and then want to send a different output to another projector (using another SDI-HDMI converter). For the output through an aux, can I select the aux and mix video inputs in the same way as the program out? Or even get a multiview that will show Preview and Aux rather than Preview and Program, but be able to switch between where I'm mixing to?
0
Thank you for the helpful info!
Ciao Michael, tu eres un verdadero sabio, bigup.
Thanks kindly!
*point of correction* i have the atem mini pro , Buh i do run hdmi cables as long as 50meters no signal boosting needed
I purchased this switcher with 2 Canon XA11 cameras. I’m not getting any feed on them. They have the same frame rates. Any thoughts?
Is it possible to punch from source to source directly? I host a twice channel the least amount of key presses the better. Thank you
HI thanks for the info. Got my cams connected. Activity on the audio meters, but no pic on thumbnails, just black. Same cams, same settings when connected to Web Presenter look good, but black on ATEM. Thank you
Hi can I check if you manage to resolve this issue ?
Excellent Video from Michaels camera... one question: can I mute all the cameras and use an input audio source from a Mixer for example
Hi I connect my two Sony 2500 to black magic but I can only see and hear audio but images is blank please help
Hi did you manage to resolve this issue ?
Hey, great video, very clear, thanks a lot! Question, do I need a video capture card to input to my pc? does it have a usb3 cable to directly send output to my pc?
Please help! I have a dslr t7i running 1080p29.89 FPS. It seems to not be connecting to the ATEM, even if I change the FPS in both sources, ATEM and camera
Can one use this as a replacement to the Web Presenter? I.E is this an upgraded WP? Thanks!
Hello I got on my multiview monitor just says Black not Camera in all the places for the camera. What could be the problem?
Thanks. Good video!
Hello, I have an Atem Television studio HD Switcher. I am struggle to connect it to my Canon 60d DSLR camera. Please can you help me with it
Hello, I have just received my Black Magic HDMI to SDI and running into my Black Magic Web Broadcaster to my iMac thorough OBS. The Picture is barely visible and lines all along the scene as well it is also show the same in the web broadcasters lcd panel. If I just connect from my canon camera to the web broadcaster via HDMI it works perfect. Any ideas on what to do? Thanks in advance.
What are the settings for size of screen? 1280 x ?
I'm not sure if you're still picking these comments up, but when you said you can run two separate multicams out (one SDI, one HDMI) did you mean they can be configured separately or are they just a cloned output? Also do you think it's worth getting a loom made up for the long runs of cables for SDI or does that limit your camera placements?
we have found out that unless your camera can output a mono signal onto both channels the ATEM television studio HD is no good for audio unless you use a separate mixer. The audio signals are linked stereo on the ATEM which means if you only have one microphone plugged in it will be permantly panned hard left or hard right and there is no way to change this position unless you use the more expensive 4K version of the system.
블랙매직디자인 스위쳐 ATEM Television Studio HD
믹서에서 카메라신호와 마이크 신호 받아서 프리뷰로햐서 자막기에서들어가서 hdmi해서 캡처보드 보냐는대요.
믹서에서 멀티뷰 말고 출력단자가 4개sdi단자있는대 바로 출력하면 자막기에서 자막 입혀서 나가서 캡처보드 / 자마막기에서 자막 입혀서 믹서에 4개 sdi 단자로 출력 가능할까요?
Hi there, having this can you please tell me WHERE TO RECORD our program output.? Only on cameras..? Or where to record to the final product.? please describe
michael... sdi out goes to where?
When I connect my 2 cameras the switch doesn't get the video signals and instead of it only shows me a black screen and gets the audio. I'm trying to record 1080p signals in 29,97fps I REALLY hope you can help me. Thanks
Make sure that you match the resolution of those two camera hope those cameras are the same MAKE and MODEL and then set the same resolution on the ATEM and that should work.
I thought there is a re sync function for different frame rates ?
i all i need to know wy black magic dont have a support on line? i have the same type of atem television studio hd but i need to use it like video mixer it must manage all video resssource .so when i connect video by sdi port it dont print it macthing only from hdmi port ;could you assit me to setup pleaze advencing think s
produce blackmagic atem studio verry good produce
I would have loved to see a connection of the Camera and Laptop/pc input. I seem to be having challenges with getting a laptop signal to the mixer.
Could you kindly advice on what I could be doing wrong?
The important thing to remember when Switching Cameras and Computers is to have everything on the same standard - in 99% of cases this means 1080p60. If you can't get all sources on the same standard you might need to convert the problem signal to match your main standard. For this job you want to get a Blackmagic Teranex AV into your system. Check out this video: ua-cam.com/video/ed8BbhWJ6g8/v-deo.html
Is this an area where the Roland V-1HD / V1-SDI has the advantage over this Blackmagic offering at this price point?
Can this unit be used with chromakey, PinP and split picture
can I use three GoPro 7 black cameras with the atem?
THANK YOU MASTER
how do I link the Atem Television Studio HD with the black Magic Video Assist?
I have 2 monitors that I want to feed a clean picture onto. How do I output on the the TV or big monitor? That's where I get it wrong.
You could use an AUX output from the ATEM along with a SDI to HDMI Micro Converter to drive a standard TV set that has HDMI inputs.
@@michaelscamera sir, what is use of sdi out put pins
Thank you so much 🙌🏻
las entradas de video son muy delicadas, tengo este equipo y ya se dañaron las entradas y salidas de video
Hey,
I have trouble to get Capture to Record on my Blackmagic ATEM. When I hit the capture it say I need to install Blackmagic Design Desktop video
Can you help me guys. I want go to stream 1080p how can i. And I also want to record 1080p
How would I record the switched feed onto a hard drive. No live streaming needed.
Michael, you can record the streaming output with any standard application that can record from a web cam. Do keep in mind that this will be at 720p. Otherwise you will need a video capture card with HDMI or SDI inputs. The way we record is with a standalone Blackmagic Hyperdeck. There SSD and SD versions of these Hyperdecks. Very nice products.
How do I live stream to Facebook with Atem television? Should I connect the device directly to the PC ??
The ATEM does the Video Switching, to stream you will just send the output from the ATEM to the Blackmagic Web Presenter. Check out this video: ua-cam.com/video/TFzFAZLSu_Y/v-deo.html
michaels camera - video - digital thanks sir !
Hi, I'm liking your video, but what if I don't wanna use the web presenter can I just input the signal with declink (or something similar) - and then use other software to stream it? Do you have a video how the ATEM control software works in this kind of situation? The goal that I'm trying to create is a streaming solution for 2 or more cameras that would require only one laptop that would do both the live editing and streaming.
The ATEM control software is completely independent of your method of streaming. As long as you can capture the video output from the ATEM into your computer (or even a stand alone streaming device) and get it to a streaming application you should be good to go. Keep in mind you don't need to do the live switching from the ATEM software as the basic controls are on the front panel of the ATEM. The other software items (like OBS Studio) just run in the background on the computer once you set them up and go live.
hm how does the 'web presenter' stream? don't you need another computer to actually do the streaming?
You are correct, the Web Presenter's output is a Web Camera feed over USB to a computer. The beauty of this system is any software you like can take a Web Camera feed.
how bout some pc input and lower 3rds
Hi, can I use Lumix GH3?
Hi Fouz. Can you please provide a little more detail about how we can assist you? Warm regards, Peter Michael, Managing Director - michaels
i still dont understand how the audio connect to atem
I Wish this was more affordable.
It IS affordable....
ya sabemos que no podemos recomendar el equipo, de ahora en adelante cuando me pregunten en santo domingo, republica dominicana por los productos de blackmagie le dire no lo compren que tienen problemas de carga no tiene protecion y mas no tiene reparacion en santo domingo y estados unidos....LES DIRE NO LO COMPREN TIENEN PROBLEMAS DE VOLTAJES