ua-cam.com/video/ah2Llv7Pp2w/v-deo.html This is our latest tutorial about this module, which introduces the principle, wiring and pairing of the module in more detail; if you have any questions, you can watch this video again; I hope it can help you solve the problem! Let everyone understand the working principle of this module better
Thanks a lot! The user guide didn't tell how to erase the codes. Also the programming looks so much easier when I see it in video. The guide was not very clear because it was auto translated from Chinese. This was very clear video and had nothing unnecessary but pure facts.
if you are looking to purchase remote controls again, you can always check out rodot.aliexpress.com/store/1456073?spm=2114.12010108.nav-home.1.411a2c9fdP5gEr or qiachip.com/
it's garbage it does not learn any RF i tried two different remotes and it won't learn any RF , i used a PT 2262 and other remotes it will not learn any of them i know they are 433MHZ and it will not learn them
@@mapton1 You can use the same remote button with many relays to control them with one remote. Or you can use 2 or more remotes with the same relay. To do so, for example press the relay button 2 times for toggle mode learning, then press buttonA from remoteA to save that remote button for toggle mode, and then press the relay button 2 times for toggle mode learning, and then press buttonX from remoteX to save that remote button for toggle mode and so on if you want to add a 3rd 4th remote ... By doing this you can have 2 or more remotes doing the same function (toggle mode in the example above).
Есть ещё режим таймера, 1) это 4 нажатия кнопки на реле и настройка пульта на включение на 5 секунд. 2) 5 нажатий, на 10сек.и 3) 6 нажатий кнопки реле, на 15сек. По истечении времени реле отключается автоматически. К реле можно привязать до 50-ти пультов Сбросить все пульты можно зажав кнопку на реле на 8 секунд до загорания индикатора на реле, или как в видео нажатием 8 раз на кнопку на реле. 🖐️😉
I guess it's implied that if you are asking about a power supply you would know that you could use battery or a power supply and would know how to hook up already I guess like if we were in algebra they would assume we already know how to perform subtraction and addition
Same for me : I recently purchased the same generic model. But if I want to reset (delete the RF codes) and press 8 times it doesn't do anything and doesn't reset anything. I found that to reset the device I have to press and hold the relay button for 6 seconds then the LED flashes 4 times (keep holding the button until it stops flashing, don't release when it is flashing or else it will reset and directly enter momentary mode learning) to indicate that it reset successfully.
I wanted to ask you for advice. I have connected a Normally Open electrometallic lock to this relay but I would like to add a led that lights up when the lock is not in action.
Do you want the state of the lock to be the opposite of the state of the LED you added? That is, when the lock is powered off, the LED turns on; when the lock is powered on, the LED turns off. Is that correct?
Please tell me where find a 220 volt remote control in which there is one channel but only with an independent contact. MEET that with the help of the remote control it was possible to connect the break of an independent circuit.
I recently purchased the same generic model. But if I want to reset (delete the RF codes) and press 8 times it doesn't do anything and doesn't reset anything. I found that to reset the device I have to press and hold the relay button for 6 seconds then the LED flashes 4 times (keep holding the button until it stops flashing, don't release when it is flashing or else it will reset and directly enter momentary mode learning) to indicate that it reset successfully.
Very good, buddy, you are very smart! From your description, I can confirm that you bought the same type, but not our product, because different manufacturers have different design logics So you have to follow his From your description, I can also know that his design is a bit unreasonable But you can still grasp it You are really great
Hallo, i have a question. Could i use this as a kill switch for my motorbike? Lets say to cut the line from the plus of the battery to store the bike when shopping or something and put the second button to start the bike from distance? I have a mecanical kill switch and at the other side a mecanical engin starter switch. I would cut the wires and pass them true this device. So that i could use the orignal swtiches when the remoute switch is on ON for the main power. Thank you
Thanks a lot for this tutorial that save my life. Just, on mine (AK-RK01SY), for the reset I have to maintain the switch until the led flashes instead of pressing 8 times.
Thank you for your comment. I’m glad I had the opportunity to answer your question. First we need to confirm one thing: is your receiver of our brand? Because each brand has different manufacturers, its functions are also different. Secondly, if you cannot reset, you can ask the merchant where you purchased it to ask questions, exchange goods, or even leave comments Finally, are there any problems that need to be solved after the reset? Is there another way to solve it? If it doesn’t work, you may need to buy a new one. I hope it helps you, and I look forward to your follow-up feedback.
@@wildanchannel2 I recently purchased the same generic model. But if I want to reset (delete the RF codes) and press 8 times it doesn't do anything and doesn't reset anything. I found that to reset the device I have to press and hold the relay button for 6 seconds then the LED flashes 4 times (keep holding the button until it stops flashing, don't release when it is flashing or else it will reset and directly enter momentary mode learning) to indicate that it reset successfully.
I put my receiver on 24v 26v but don’t work only flashing lights but relays don’t work can u tell me what adapter you guys using or were to get power from also try battery charger 24v and did work but can’t use battery charger all the time??!
It is hard to type out the wire schema. But you can check out www.aliexpress.com/store/product/433Mhz-Universal-Wireless-Remote-Control-Switch-DC12V-1CH-relay-Receiver-Module-and-RF-Transmitter-433-Mhz/1456073_32716729232.html for a more detailed descriptions
I just bought a receiver and transmitter exactly like yours, I have connected it to 12 volts, the wiring is exactly the same as yours, erase the existing data by pressing 8 times the learning button, but when I press the learning button and then the button of the receiver, the red light of the receiver is still on, the same occurs in any of the modes of oepración, ie the receiver does not detect the transmitter, do you think the receiver is damaged or the problem is the transmitter?
Oh, that's not right. The garage door has the function of up and down, that is, forward and reverse. If your garage door is equipped with a controller, the controller will convert the voltage to 12V or 24V . You can watch this video: ua-cam.com/video/o7SbTBAeAlU/v-deo.html . If your garage door directly drives the motor, then watch this video: ua-cam.com/video/EQyKgdRzZOE/v-deo.html. It is dedicated to 220V! I hope this helps you, and looking forward to your feedback.
I have two of these remote control units can I use one remote control to control both of the PCB boards as I would like to use a button for one board and use B button for another board is this possible
Zaheer Sarwar you can scroll down from this page for wiring diagram www.aliexpress.com/store/product/QIACHIP-433MHz-Universal-Wireless-Remote-Control-Switch-DC-12V-1CH-RF-Relay-Receiver-433-MHz-Receiver/3681001_32862095630.html remember to use your computer to open the link for the diagram
The more practical approach would be wiring the com with - then plug in the power source on + and - once it’s done just plug in your lock, plug in your lock + to NO and - to -
I got zero documentation with mine, not even what you are holding up. What are the inputs and outputs? I need a momentary switch for my garage door opener (like pushing the doorbell style button to open it).
@@qiachip I tried that, with an LED and it would not light up or flash. Positive should be com and negative to NO, correct? I don't hear the relay click, even though the red light on the board lights when I click B.
We do not have settings in programming, because generally users only learn two remote controls, and then take them out for pairing after clearing the codes. This can avoid hidden dangers of some remote controls not being cleared.
qiachip.com thanks for the response but what I want to know is if it can work as a toggle switch for the ignition power line, considering that car battery supplies 12v and from 60 - 80a
I bet if you used a 4pin hooter relay with input output function you would be able to power up 30 to 60A power. I used a nos button through a 4 pin input output switch as a start button. Yes more wiring but effective.
@@qiachip Hi, I connected this relay to a coil with an external 12v 4 Amp battery, but after a few dozen activations and deactivations in the remote control, it heats up very much ... could it burn out?
Hi Harvey, You can use it in any applications. The lights in the video is just a prop for how to pair the receiver and the transmitter (remote control) properly. So, feel free to use it on any way you pleased.
Well, first you need to know the frequency it's receiving on. You can start by stretching the coil into a straight Ground plane antenna, which will dramatically increase the distance... If you would know the frequency it receives on, than you could make on your own a big quarterwave antenna ANd place outdoor or on the roof..ooooor (And this is the most effective way, create yourself a beam antenna which is tuned on the right frequency. And you'll be able to cross miles in open territory ..... Buuuuuut I don't know on which frequency this thing transmit, so it's better to not mess with the FCC 😅
Ok, just opened the device and it's transmitting at 433MHz UHF band, which is legal to use with a maximum power of 10 mW but it needs to have fixed antenna's, so no space for (legal) fiddling. Cheers
You can check out the circuit chart from www.aliexpress.com/store/product/433Mhz-Universal-Wireless-Remote-Control-Switch-DC-12V-1CH-relay-Receiver-Module-3pcs-RF-Transmitter-433/2138259_32815532310.html?gps-id=5298742&scm=1007.14677.110221.0&scm_id=1007.14677.110221.0&scm-url=1007.14677.110221.0&pvid=49524cde-48b9-4455-ba35-38a7791dd96f&spm=a2g1y.promotion-20181111.promoteRecommendProducts_6091620.31 Basically it is really simple, + - for powering the device, then connect the device you wanna control. Pair the device with a remote transmitter and you are all set.
Hi, I have the same relay module as you. When I try to make it learn a code I press the button 8 times, so it resets, then I press it once to activate toggle mode. when I press the remote button the light doesn't blink but it only turns off and the card doesn't learn the code. What should I do?
Hello, QIACHIP 12V 1CH receiving module contains a delayed shutdown function. You only need to configure the remote control in this way to use this function. 1. Press the learn button on the receiver 8 times to reset the receiver. 2.5s delayed shutdown: press the learning button on the receiver 4 times, then press the remote control button again, the configuration is complete 3.10s delayed shutdown: press the learning button on the receiver 5 times, then press the remote control button again, the configuration is complete Function explanation: After pairing, press and hold the remote control button to keep the relay on. Starting from releasing the remote control button, the relay will close after a 5s/10s delay Purchase link ：www.amazon.com/dp/B07GJT1D1Z
ua-cam.com/video/ah2Llv7Pp2w/v-deo.html
This is our latest tutorial about this module, which introduces the principle, wiring and pairing of the module in more detail; if you have any questions, you can watch this video again;
I hope it can help you solve the problem! Let everyone understand the working principle of this module better
Thanks a lot! The user guide didn't tell how to erase the codes. Also the programming looks so much easier when I see it in video. The guide was not very clear because it was auto translated from Chinese. This was very clear video and had nothing unnecessary but pure facts.
At the start of the video, there are code clearing guide. When we press the learning button 8 times, after the LED flashes. The code is cleared.
Great video, the instructions supplied in the box are incomplete - your video is perfect. Thank you.
I agree. Thank you very much. Your teaching is very clear.
Köszönöm! :-) Végre be tudtam állítani self-locking módba!
This worked perfectly on a similar system! Thanks a bunch!
Thank you
@@qiachip RANGE ? (will it work from another room 10-15 feet away?
GOOD job. your video helped me a lot because the receiver i purchased didnt come with very good instructions.
if you are looking to purchase remote controls again, you can always check out rodot.aliexpress.com/store/1456073?spm=2114.12010108.nav-home.1.411a2c9fdP5gEr or qiachip.com/
Great tutorial! Thanks. I use mine with two remotes in the latch mode. Works great!
Can you make a vid on how to wire it?
Think u very much, i found you and the guide how to reset my module.
Thanks! I bought the card after watching the video!
Thanks!
it's garbage it does not learn any RF i tried two different remotes and it won't learn any RF , i used a PT 2262 and other remotes it will not learn any of them i know they are 433MHZ and it will not learn them
Yes, this product has been eliminated,
Thank you so much for making this!😃
Thank you! The instruction for adding a second remote worked perfect.
I only see one remote being programmed?
@@mapton1 You can use the same remote button with many relays to control them with one remote.
Or you can use 2 or more remotes with the same relay. To do so, for example press the relay button 2 times for toggle mode learning, then press buttonA from remoteA to save that remote button for toggle mode, and then press the relay button 2 times for toggle mode learning, and then press buttonX from remoteX to save that remote button for toggle mode and so on if you want to add a 3rd 4th remote ...
By doing this you can have 2 or more remotes doing the same function (toggle mode in the example above).
Есть ещё режим таймера,
1) это 4 нажатия кнопки на реле и настройка пульта на включение на 5 секунд.
2) 5 нажатий, на 10сек.и
3) 6 нажатий кнопки реле, на 15сек.
По истечении времени реле отключается автоматически.
К реле можно привязать до 50-ти пультов
Сбросить все пульты можно зажав кнопку на реле на 8 секунд до загорания индикатора на реле, или как в видео нажатием 8 раз на кнопку на реле. 🖐️😉
У меня не сбрасывается зажатием ни на 8 секунд, ни на 5, как написано в руководстве. Только 8 нажатий
Super bien expliqué même sans parole !!! merci
Sat Sri akaal my friend. I hope I spelled that right lol.
great tutorial and very simple to understand......and multilanguage....!!!
Good man, great video, cheers for your help
Great work.....Thank you for the video
Why don't these video ever show the power source
ua-cam.com/video/QuFzDcIiDxQ/v-deo.html
It's simple the black wire going up is ground, the orange is power
I guess it's implied that if you are asking about a power supply you would know that you could use battery or a power supply and would know how to hook up already I guess like if we were in algebra they would assume we already know how to perform subtraction and addition
😂 dont be too harshed to someone's kids😂@@bodhi-f6p
very helpful video... thanks 🎉
Thank you for the helpful programming modes! Mine doesn’t come with instructions
Easily understood. i like latch mode.
Very helpful, thanks for the video
Can you show your wiring setup please
Muchas gracias, ya me tenia aburrido.
If I use a 12 volt battery to power the relay, will it drain my battery when not in operation?
Yes, it consumes power because its receiver is always working and ready to receive signals.
hi new friend supporting you
Excellent post. Thank you so much! Is there a setting when you click 7 times?
Yes, it will delay 20s to turn off the relay
Muchas gracias. He visto bastantes vídeos sobre esto, pero tan comprensible como esté muy pocos.
Muchisimas gracias, bien explicado, simple y practico.
bought one of those different brand though, horrible instructions but was able to figure it out, using it to turn my power inverter on
Wow.good experiment
Holding 8sec to erase codes worked for me.
Same for me :
I recently purchased the same generic model.
But if I want to reset (delete the RF codes) and press 8 times it doesn't do anything and doesn't reset anything.
I found that to reset the device I have to press and hold the relay button for 6 seconds then the LED flashes 4 times (keep holding the button until it stops flashing, don't release when it is flashing or else it will reset and directly enter momentary mode learning) to indicate that it reset successfully.
I wanted to ask you for advice. I have connected a Normally Open electrometallic lock to this relay but I would like to add a led that lights up when the lock is not in action.
Do you want the state of the lock to be the opposite of the state of the LED you added?
That is, when the lock is powered off, the LED turns on; when the lock is powered on, the LED turns off. Is that correct?
It's working thank-you very much
Please tell me where
find a 220 volt remote control in which there is one channel but only with an independent contact. MEET that with the help of the remote control it was possible to connect the break of an independent circuit.
Great video. Thanks for sharing.
I recently purchased the same generic model.
But if I want to reset (delete the RF codes) and press 8 times it doesn't do anything and doesn't reset anything.
I found that to reset the device I have to press and hold the relay button for 6 seconds then the LED flashes 4 times (keep holding the button until it stops flashing, don't release when it is flashing or else it will reset and directly enter momentary mode learning) to indicate that it reset successfully.
Very good, buddy, you are very smart!
From your description, I can confirm that you bought the same type, but not our product, because different manufacturers have different design logics
So you have to follow his
From your description, I can also know that his design is a bit unreasonable
But you can still grasp it
You are really great
Can i use this for 36v kids quad? Need this for safety , thanks
How much power can it handle? Car horn?
Hi. Can be fitting to bmw car ? To stop steering 😢? Thanks
You are doing what I want to do, But I need to know the wiring to 'NO Com NC V- V+'. Can you show that????
Hi if I don’t know how to connect them how will I know how to program them?
Hallo, i have a question.
Could i use this as a kill switch for my motorbike?
Lets say to cut the line from the plus of the battery to store the bike when shopping or something and put the second button to start the bike from distance?
I have a mecanical kill switch and at the other side a mecanical engin starter switch.
I would cut the wires and pass them true this device.
So that i could use the orignal swtiches when the remoute switch is on ON for the main power.
Thank you
Hi did you use this for that in the end
Excellent description.
Thanks a lot for this tutorial that save my life. Just, on mine (AK-RK01SY), for the reset I have to maintain the switch until the led flashes instead of pressing 8 times.
Parabens pela aula.
Thanks！ good student!
What is the wiring steps for this? Thank you
Real range?
🎉🎉supar supar 🤝
Does it "save" your settings so you don't have to redo the programming everytime you provide power once again?
Yes, it will save the settings. Even if the power is disconnected.
does it work with an input of 2.5A will it have an output?
thank you so much for this information
Can anything be done to the antenna for longer reach
What frequency is this?
Does another remote controller can on/off relay.....
Yes, as long as you can pair with the remote control, you can control it.
@qiachip But Sir,I want to use it in lock and bike.If it is on/off by by another remote then security will not be......
Can you help me.. My modul no reset mode.. Led always blink 3x after reset mode
Thank you for your comment. I’m glad I had the opportunity to answer your question.
First we need to confirm one thing: is your receiver of our brand? Because each brand has different manufacturers, its functions are also different.
Secondly, if you cannot reset, you can ask the merchant where you purchased it to ask questions, exchange goods, or even leave comments
Finally, are there any problems that need to be solved after the reset? Is there another way to solve it? If it doesn’t work, you may need to buy a new one.
I hope it helps you, and I look forward to your follow-up feedback.
@@qiachip ok my friend thank for information.. Looks like I'll have to buy a new one
@@wildanchannel2
I recently purchased the same generic model.
But if I want to reset (delete the RF codes) and press 8 times it doesn't do anything and doesn't reset anything.
I found that to reset the device I have to press and hold the relay button for 6 seconds then the LED flashes 4 times (keep holding the button until it stops flashing, don't release when it is flashing or else it will reset and directly enter momentary mode learning) to indicate that it reset successfully.
can i use whitou control? i want to use with radio baofeng, wil work?
Can it be controlled by other remote devices without pairing them?
I put my receiver on 24v 26v but don’t work only flashing lights but relays don’t work can u tell me what adapter you guys using or were to get power from also try battery charger 24v and did work but can’t use battery charger all the time??!
12V adapter
What is wire schema for momentary? please provide.
It is hard to type out the wire schema. But you can check out www.aliexpress.com/store/product/433Mhz-Universal-Wireless-Remote-Control-Switch-DC12V-1CH-relay-Receiver-Module-and-RF-Transmitter-433-Mhz/1456073_32716729232.html for a more detailed descriptions
What does the wiring look like to control two separate leds with A and B buttons? Can you show that? Thanks
did you get answer?
I just bought a receiver and transmitter exactly like yours, I have connected it to 12 volts, the wiring is exactly the same as yours, erase the existing data by pressing 8 times the learning button, but when I press the learning button and then the button of the receiver, the red light of the receiver is still on, the same occurs in any of the modes of oepración, ie the receiver does not detect the transmitter, do you think the receiver is damaged or the problem is the transmitter?
Can you give us the link where you make your purchase? Thx.
qiachip.com ,i have same problum how can i know my reciver or transmeter faulty.
I buy from ali express china.
farasat ali still, can we have the link where you’ve purchased the product from? Since our product do not usually have such problem
Does it work with 220V garage door?
Oh, that's not right.
The garage door has the function of up and down, that is, forward and reverse.
If your garage door is equipped with a controller, the controller will convert the voltage to 12V or 24V . You can watch this video: ua-cam.com/video/o7SbTBAeAlU/v-deo.html .
If your garage door directly drives the motor, then watch this video: ua-cam.com/video/EQyKgdRzZOE/v-deo.html. It is dedicated to 220V!
I hope this helps you, and looking forward to your feedback.
@@qiachip I think I bought the wrong switch 😞
I will buy the 2ch one 220v
I have two of these remote control units can I use one remote control to control both of the PCB boards as I would like to use a button for one board and use B button for another board is this possible
Yes, you can use it like this.
Can this circuit board power a 12v golf trolley.
Yes, it’s most likely 12v 10a
Any ideas for a wiring diagram! I'm stuck I'm trying to use a solenoid for a door lock to work on this device ?
Zaheer Sarwar you can scroll down from this page for wiring diagram www.aliexpress.com/store/product/QIACHIP-433MHz-Universal-Wireless-Remote-Control-Switch-DC-12V-1CH-RF-Relay-Receiver-433-MHz-Receiver/3681001_32862095630.html remember to use your computer to open the link for the diagram
The more practical approach would be wiring the com with - then plug in the power source on + and - once it’s done just plug in your lock, plug in your lock + to NO and - to -
@@qiachip excellent this has worked for me. Thank you for your help!
Zaheer Sarwar no problem, feel free to ask us anything about our products
@@qiachip can I power this using lower voltage like 5v??
Спасибо без слов но всё понятно👌👌
I got zero documentation with mine, not even what you are holding up. What are the inputs and outputs? I need a momentary switch for my garage door opener (like pushing the doorbell style button to open it).
First, you need the right wiring. The two terminals COM and NO can output the switching signal.
Then you need to set the momentary working mode
@@qiachip I tried that, with an LED and it would not light up or flash. Positive should be com and negative to NO, correct? I don't hear the relay click, even though the red light on the board lights when I click B.
You can send a video at UA-cam and give me your video link.
I guess your wiring and settings are incorrect.
Can I wire this into a cars fuel pump wiring?
Can it work with 9v battery or 12v battery?
Hello, is it possible to delete only one remote control?
We do not have settings in programming, because generally users only learn two remote controls, and then take them out for pairing after clearing the codes. This can avoid hidden dangers of some remote controls not being cleared.
I have 12 v leds pre wired but I’m looking to set them up with a remote and battery power any advise?
Hello can I used with normal AC Adapter with 12V === 1.5 A or the 1.5 Am is to much thanks
I have 2 autogate door..button a for 1 door open/close..then button b for open/close 2 door..how to setting
Set Toggle Mode.
Can I also use this to operate a CDI unit on a scooter?
I am not sure about this, you can try
Can u show how the wiring is attached please
Quando desernegizar o rele de acionamento, ele perde a configuração em q foi feito? Tera q configurar novamente?
Olá, não há necessidade de reconfigurar
Why the device suddenly turn off without pressing remote button?
Please help!
thank you
Is it possible to make a parallel connection with a normal physical switch?
Switches are usually in series
Sir thank you for this video, please tell me what is the maximum number of remotes we can pair with this 1CH relay receiver module ?
I have two, so at least that amount.
The system can have 15 remote control units, if the remote control gets more than 15 units, lose the initial remote control.
Anyone know if it needs charging or do you put a battery connected to it?
@@williamjames0 The remote needs battery
@@kanalord4134 but does the actual system?
do you have a wiring diagram please?
Yes! We must to be need,you can see some wiring diagram by www.amazon.com/dp/B07GJT1D1Z?ref=myi_title_dp,so good product 😉
can this be used in cars? I mean place on the ignition power/circuit line?
We would suggest not using beyond 80°C
qiachip.com thanks for the response but what I want to know is if it can work as a toggle switch for the ignition power line, considering that car battery supplies 12v and from 60 - 80a
Hello that would be too high for the receiver as it holds 10A power.
qiachip.com Ok thanks. Isn't there anyone that can work for it?
I bet if you used a 4pin hooter relay with input output function you would be able to power up 30 to 60A power. I used a nos button through a 4 pin input output switch as a start button. Yes more wiring but effective.
Hi, this control works at 12V, but at how many amps does it support?
The input current does not need to be so high, but the output current does not exceed the 10A required on the relay.
@@qiachip Hi, I connected this relay to a coil with an external 12v 4 Amp battery, but after a few dozen activations and deactivations in the remote control, it heats up very much ... could it burn out?
@@DiCe.20-p9g Not in a short time。
Y como le hago para darle corriente para que este encendido tiene muchos cables?
Can we use it in other application except controlling led??
Hi Harvey, You can use it in any applications. The lights in the video is just a prop for how to pair the receiver and the transmitter (remote control) properly. So, feel free to use it on any way you pleased.
qiachip.com Thanks. Im planning to use it in infrared sensor i hope it is possible.
Range ?
What is the range of this transmitter to receiver??
Well, first you need to know the frequency it's receiving on.
You can start by stretching the coil into a straight Ground plane antenna, which will dramatically increase the distance...
If you would know the frequency it receives on, than you could make on your own a big quarterwave antenna ANd place outdoor or on the roof..ooooor (And this is the most effective way, create yourself a beam antenna which is tuned on the right frequency. And you'll be able to cross miles in open territory .....
Buuuuuut I don't know on which frequency this thing transmit, so it's better to not mess with the FCC 😅
Ok, just opened the device and it's transmitting at 433MHz UHF band, which is legal to use with a maximum power of 10 mW
but it needs to have fixed antenna's, so no space for (legal) fiddling.
Cheers
is there a small battery source I could use to hold open a servo that would work exactly the same as this but a small portable battery source?
I used a battery case with 8pcs 1.5V batteries.
Did you try an a23 battery it's a tiny 12v battery found at any shop or supermarket
Sir I need this circuit where it is available
You can check out the circuit chart from www.aliexpress.com/store/product/433Mhz-Universal-Wireless-Remote-Control-Switch-DC-12V-1CH-relay-Receiver-Module-3pcs-RF-Transmitter-433/2138259_32815532310.html?gps-id=5298742&scm=1007.14677.110221.0&scm_id=1007.14677.110221.0&scm-url=1007.14677.110221.0&pvid=49524cde-48b9-4455-ba35-38a7791dd96f&spm=a2g1y.promotion-20181111.promoteRecommendProducts_6091620.31 Basically it is really simple, + - for powering the device, then connect the device you wanna control. Pair the device with a remote transmitter and you are all set.
qiachip.com when i push white boton red lite comes for 5second only this is going on in my reciver.
Gupta - Amazon "eMylo"
Can this open cars
Hi, I have the same relay module as you.
When I try to make it learn a code I press the button 8 times, so it resets, then I press it once to activate toggle mode.
when I press the remote button the light doesn't blink but it only turns off and the card doesn't learn the code. What should I do?
Can I use it to enable and disable a 2 wire push switch if so how do I wire it with a 5-10 second active delay
Hello, QIACHIP 12V 1CH receiving module contains a delayed shutdown function. You only need to configure the remote control in this way to use this function.
1. Press the learn button on the receiver 8 times to reset the receiver.
2.5s delayed shutdown: press the learning button on the receiver 4 times, then press the remote control button again, the configuration is complete
3.10s delayed shutdown: press the learning button on the receiver 5 times, then press the remote control button again, the configuration is complete
Function explanation: After pairing, press and hold the remote control button to keep the relay on. Starting from releasing the remote control button, the relay will close after a 5s/10s delay
Purchase link ：www.amazon.com/dp/B07GJT1D1Z
What is the output of that device? Ty
12V, if you have an external power supply, you can also connect to loads with other working voltages
for what is used this?
Mostlikely when you want a remote control for something like your ebike to turn on
B shall be the same key and A key way of learning
The video demonstrates three "working modes" settings.
Hola! Lo he conectado al telefonillo de mi casa. Pero cuando abre hace un ruido un poco raro. Supone algun problema? Gracias!
Vous pouvez montrer le branchement ? merci
Hello, can I put two DRL led bar connected to this device in parallel?
Cheers.
Yes， you can.
qiachip.com great! Thank you!