If you had been an instructor years back at vocational school, I’d be an auto mechanic today lol. Excellent video, easy to follow and understand. Great Job!!
Very methodical troubleshooting. I've been fixing cars for 25 years and I'm always learning some new trick or tip from you! Thanks for making all your videos for the UA-cam community.
Been a few years since I pulled wrenches for a living , but apart from a few dribblers and odd shaped spray patterns, injector failure was fairly low on the ladder of anticipated failures. Which is kinda amazing considering how many millions of times they have to cycle to get you down the road...if I'm not mistaken my old 68 square back had Bosch injectors which never seemed to fail.
97 Explorer Limited suddenly dropped from 15 to 8 MPG around town. 150K on the clock, wife's car and I do all the maintenance. Surfed looking for fuel pressure numbers and Alexa led me to your channel where I have been subscribed for awhile. Great content as always and well done. Thanks
Just today-same problem - put pressure guage on fuel line out of tank and found the check valve leaked back. New fuel pump assy being installed. Will check, then recheck at rail. Very good on your presentation.
Wow, when you said "it might just be your time" in the beginning, I have never laughed so hard during an SMA video. Pure genius. This is just one of the reasons I'm a big fan. Keep it up!
Great video. I have a fuel pressure loss in my Subaru that I need to troubleshoot, and this is spot on for evaluating what's wrong, helps me out a ton for plan of action.
Followed your advise with a job that came in today for non start, purchased a fuel pressure tester and turned out to be fuel pump pipe inside fuel tank had split and was leaking internally not holding fuel pressure!! Life saver 100% answer! Proved and verified. Just had the happy job of dropping fuel tank and replacing split pipe. 👍
I had a similar problem on my ranger. Mine wasn't a hard pipe. It was a split hose inside of the pump assembly. I noticed the split hose about a day after I replaced the assembly. Now for the cost of 2 inches of hose and 2 clamps, I have a spare pump if I ever need one.
I want to thank you for this video! My 2000 LeSabre, while hard starting, was running pretty well. It wasn't backfiring like with a leaky pressure regulator. (I'd changed it 5 yrs ago only later to find it had been the subject of a recall a decade before it failed.) While I don't have your tools, I do have a gauge manifold and a small compressor. Following your method, with no external leaks, I determined it must have a faulty pump and replaced it. Inspecting the old part, I found a pin hole leak in the plastic flex line, bleeding pressure back into the tank, between the pump discharge and the top of the assembly. Oh yeah! Bonus. I also now have a working gas gauge.
Hell of a great video! Well explained and now I know how to check the system better! I have a few more issues to check before ripping out the pump. Appreciate your knowledge! Keep up the great work buddy!
This is an amazing mechanic! Very good Sir, and you’ve helped me to go somewhere with an issue I’ve got on my older f150 with a 4.9 EFI. Thanks so much Sir! Wow, yes it was definitely spraying like wide open like no injection was there like you have equated on this video! Never will have thought an injector could as you say leak the volume it did… just wow, wide open like not there…
Great video showing the logical steps. I think the BMW N63 V8 had a similar issue with a failed injector hydrolocking the engine and destroying it (with dealers charging $25K+ to replace the engine). The ECU monitors the fuel rail pressure and could, if manufactures wanted, detect a key on no-crank injector leak and then throw a code and prevent you from cranking the engine. When you shut your car off it could easily detect a fuel rail leak and throw a code and even perhaps prevent cranking until the code is reset. That's a bit extreme but it might have saved BMW, and apparently GM, some engine replacements. And the injectors should be designed even if stuck open to limit the max flow to something that hopefully wouldn't hydrolock an engine just from the 2 second fuel pump prime and then being cranked. But yeah, at this point this Caddy is basically scrap.
So glad you picked my car. 2003 Cadillac Deville has the same coil pack and configuration shown on top of the engine. After having replaced the intake manifold gaskets on a 1999 Chevrolet Malibu LS , it took me seven months cause I’ve never done that sort of work before, I was elated to do the Cadillac Deville job in 3 hours. I gave up on replacing the gaskets as I noted in my last comment -they kept popping off. But the car is relatively easy to work on. I’ve replaced a wheel bearing assembly. I wish somebody would make a video about how you get the wheel bearing through that hole without breaking off the ABS sensor or whatever the hell that gizmo is that sticks out and breaks off. I used to play with Rubiks cubes and these wooden puzzle cubes so I tried every combination I could think of, but could not get that wheel bearing assembly through the hole with without breaking off what I thought was the ABS gizmo. I also gave up on replacing the fuel injector O-rings that have 106,000 miles on them. There’s a plastic ring at the bottom that keeps the O-ring 1/8 inch off the bottom. The Fel-Pro O-ring replacement kit does not have those plastic rings. If you try and take the O-ring off you break the plastic ring. And working on the Chevy it was impossible to replace the fuel injectors because the clips that hold the injector to the rail would go flying and get lost somewhere in the engine. So that was a job that never got done. I got all these Amazon fuel injectors that will never be used because the clips are so horrendous. I did not try the clips on the Cadillac engine. Everything on the Cadillac is so much better than on the Chevy for being easy to work on. My biggest gripe about the Chevy is the AC has never worked right. The 1999 Chevrolet Malibu seems totally accessible for the AC components except the condenser. If you look at the Cadillac condenser it looks like you just open the hood and out it pops. Not so with the Chevy. I find the Chevy is a nuisance to work on. But the Chevy gets 20 miles per gallon with a leadfoot in city driving. The Cadillac gets 14 at best. The Chevy is ideal for city driving and shopping trips. The Cadillac with the starter motor buried under the Plenum is better designed for interstate driving.
Happy-go-lucky. It seems like in one of Eric's Clips he was working on one with those clips that hold the injector to the fuel rail and it was determined that they were only on there to keep the injectors from falling off during assembly at the manufacturer. I would have been the same engine as yours
Awesome video... I've been looking for ways to determine why my LS won't hold pressure with the key off. Unfortunately I don't have one of those T fittings. I believe my issue is either the pump check valve or pressure regulator.
Eric O. This is an excellent presentation into diagnosing an event I have seen to date. No one does them better. Process of elimination was right on. Don't want to sound like a brown noser but, you are my hero. All that in twenty minutes. if your not getting paid somehow on these videos, something is wrong in internetville . Bless you sir.
educational as usual Sir Eric. Ive got a vauxhall (General Motors) Astra active 1.6 inline 4 with fuel injectors similar to those on the cadillac .I ve had problem with the upper sealing rings blowing out cause over presure at the pump in the tank.
The word is deluge. It deluged the cylinder. And if Hannah had not have shut her down it would have deluged SMA with fuel. Excellent and another enjoyable video to watch Eric. Thank you so much !
I’m gonna try this on my Pontiac 2.4 1998 GT. Same exact issues, Loss of pressure slowly going to check everything you did in the video. Thanks much I wish I had a mechanic in my area like you
Good call; good practical procedure to follow, but no Brake Kleen, no acetylene torch, and no explosions to liven things up. I guess you noticed that beginning at around 2:20 or 2:21, you can see gas dripping out of the T-connector at the point where you connected it to the pressurized fuel line - it happened each time you turned the fuel pump on. That little glitch could throw us DIYers off the correct diagnostic path.
Great video. Perfect timing for me to see this one because I'm currently dealing a similar situation on a 1989 F-350 dually with a 460. This will help guide me to thru the process to narrow down what my issue is. Thanks a bunch for showing us this process.
My '79 Caddy Seville EFI Olds 350" had that problem... getting 1 MPG... raw gasoline dripping out the end of the tailpipe... Caddy wanted $180 for a new injector, so I blew air through it backwards from an air hose while jumping it open with 12 volts and it cleared the clogging crud out of it... worked fine there after... still have the car... Caddy wanted $400 for pair of new rear air shocks, so bought universal ones for $50/pair... Wanted $90 for front muffler and $60 for rear resonator, so put four $15 turbo mufflers on it... quieter than stock and less back pressure!
brilliant was just dealing with a neighbours car with low pressure fault only reading 0.5 bar! new in-tank pump with built in regulator solved it cheers Eric, sandy
Great video. You make it so simple to understand. I am getting a p0171 and p0174 code. I was thinking weak fuel pump as the regulator seemed to be working, when vacuum line is disconnected the pressure goes up with no leaks. When car is shut off the pressure drops. After watching your video and seeing how you pinched off the return line l did the same. My pressure was much higher than when the car was running and it was maintained after the car was shut off. Final outcome was a bad fuel pressure regulator. Much easier to replace than a fuel pump. Thanks a million for your video. Doug in Canada
Great Video Eric, you are always a step ahead of me:) I was thinking that a thermal camera would be a good way to see if an injector was staying energized by seeing which one was hottest, but then you mentioned the thermal camera! I was also thinking that seeing which injector was COOLEST (due to the fuel flowing through it) might be a quick way to pin down the culprit.
I've been chasing my tail. I hopped up an LQ9 (basically an LS2) a bit with a custom valvetrain, cam, Johnson Lifters, rocker rollers... Then threw it in my 2001 Tahoe. Engine runs like a BEAST no issues (except P0300 code on occasion but due to bigger cam?) Bought new Delphi injectors (I now see they have very BAD reviews on Amazon). Long story short. I can warm the engine up. Then turn it off and say go in the store. When I come back it doesn't want to start. I have to crank the engine for several seconds before it will turn over. It starts perfectly under all other circumstances. I've been chasing my tail trying to tune issue out with no luck. Bad injector? I am buying stuff to diagnose. Bit nervous to pulse injector in cylinder w/ engine off like some tutorials I've seen. Have to finish watching your tutorial.
I enjoy your videos. I like the problem solving logic as well as the close ups. I'm a little hard of hearing so the clarity of the audio is important to me.
Great video Dr. O! Just had a Yukon on Friday doing that exact same thing, customers bringing it back Monday now I have a new approach for it. thanks for all the helpful information.
I'd tell the customer that there's no guarantee that it will work. because an injector leaking that badly might have caused cylinder damage not to mention engine damage in general. and knowing this they could purchase another fuel injector? (preferably a used one). because the vehicle is not worth spending a lot of money on. and clear the cylinder in question of fuel by cranking it over with the spark plug out. and then the replace the injector and put the spark plug back. then fire I up and see what happens. if it runs any better (pretty unlikely) then change the oil and drive until it dies.
I enjoy watching your diagnosis....you make What you're doing look easy. Your experience has obviously been gained through many hours of work. I only wish I could find someone like you to fix my car in barrie Ontario Canada! Thanks and ( look out scotty ) this guy knows his stuff too!
Look out Scotty if you are talking about Scotty Kilmer he has never put out a video near as good as Eric. If he does know as much as Eric he has never shown it in a video I have seen.
Great job of troubleshooting. I am currently trying to figure out a cyl 7 misfire situation on this same engine. I have replaced spark plug, boot, swapped coil assemblies and it stays with the cylinder. I have 35psi fuel pressure with key on and at idle. Misfire counters are worse at idle than higher rpms. I have replaced the fuel pump for a bad sending unit. The low fuel pressure concerns me. Any thoughts. Thanks Eric for sharing the knowledge.
Just about to get started on my 2001 Nissan Xterror with a hard start when warm.... that was an epic discovery of the leaking fuel injector! Damn son!!!
Instead of pulling the injector rail and the injectors like you did, could you not pull the plugs and check for one that is fouled with fuel? You're going to have to pull at least one to overcome the hydro lock in any case.
Excellent video Eric O !!...I picked up 2 used GM fuel line adapters (J37287 ) on Ebay for cheap...less than $100... each has the inline shut off valve....no more pinching off the lines with vice grips !!
Have a car IDENTICAL!!! to this in my stall right now. I remembered watching this a while back, and had to find it again tonight. Can't wait to get there in the morning and pull my injector to see if it sprays like this one did.
This gets a lot more fun when you have nylon lines, rather than rubber. :D Smack the injector with a hammer, bill the customer for an engine replacement, and ship it!
Thats right buddy, all that comfort NEEDS that power, I tell ya what, them Caddy Lacks pass everything on the road, mmHmm, except a gas station! Ha! I know thats right!
Great video Eric. Could be b/c it's 5am at the moment, but would you mind clarifying why unplugging each injector and then running the pump is test of the PCM?
Introducing the all new General Motors Northstar Rich Edition! *Replaceable Head gaskets still included! Buy one now! Sorry I just had to say it! Incredible work as always!
Bar engine over to relieve cylinder hydo lock. Man that brings back old memories of hydro locked Cummins truck motors which had holes in the liners from cavitation filling cylinder with coolant. To evacuate lock up bar engine in reverse engine rotation, thus allowing the fluid to escape out the exhaust value. After 3 or 4 rotations the cylinder is cleared allowing engine to be started, leave radiator cap loose and haul another load of logs. So bar reverse rotation to expel fluid.
Having the problem with 1997 Tacoma, replaced all injectors. Going to do pressure regulator next. Starts hot fine and runs good, cold start hard and have seen a little gas leakage around regulator.
So glad I watched this video. So much great information. Question, could you have removed the plugs and turned the engine over and looked for the cylinder shooing out fuel.
Had this problem on my son's '02 Silverado and replaced the regulator and no improvement. Decided to replace the fuel pump thinking it was a check valve in the pump. Turned out to be the flexible plastic line on the pump unit had rubbed on one of the pump support rods and developed a pin hole.
You have the best videos, informative, clear, no distractions, no distracting music, no dead air time. Just the facts
One of the best fuel leaking teaching, efffective actions, no bubbling. highly respectful. many thanks, 👏👏👏👏
If you had been an instructor years back at vocational school, I’d be an auto mechanic today lol. Excellent video, easy to follow and understand. Great Job!!
I'm just a DIYer, but am really learning a lot from your showing how to step through a diagnosis. Thank you.
Very methodical troubleshooting. I've been fixing cars for 25 years and I'm always learning some new trick or tip from you! Thanks for making all your videos for the UA-cam community.
2.4 caravan
Not all have a vacuum line me on pressure regulator
Been a few years since I pulled wrenches for a living , but apart from a few dribblers and odd shaped spray patterns, injector failure was fairly low on the ladder of anticipated failures. Which is kinda amazing considering how many millions of times they have to cycle to get you down the road...if I'm not mistaken my old 68 square back had Bosch injectors which never seemed to fail.
97 Explorer Limited suddenly dropped from 15 to 8 MPG around town. 150K on the clock, wife's car and I do all the maintenance. Surfed looking for fuel pressure numbers and Alexa led me to your channel where I have been subscribed for awhile. Great content as always and well done. Thanks
Just today-same problem - put pressure guage on fuel line out of tank and found the check valve leaked back. New fuel pump assy being installed. Will check, then recheck at rail. Very good on your presentation.
Wow, when you said "it might just be your time" in the beginning, I have never laughed so hard during an SMA video. Pure genius. This is just one of the reasons I'm a big fan. Keep it up!
South Main Auto you TRULY ROCK and your skills are A-1.
Great video. I have a fuel pressure loss in my Subaru that I need to troubleshoot, and this is spot on for evaluating what's wrong, helps me out a ton for plan of action.
Followed your advise with a job that came in today for non start, purchased a fuel pressure tester and turned out to be fuel pump pipe inside fuel tank had split and was leaking internally not holding fuel pressure!! Life saver 100% answer! Proved and verified. Just had the happy job of dropping fuel tank and replacing split pipe. 👍
I had a similar problem on my ranger. Mine wasn't a hard pipe. It was a split hose inside of the pump assembly. I noticed the split hose about a day after I replaced the assembly. Now for the cost of 2 inches of hose and 2 clamps, I have a spare pump if I ever need one.
Excellent demonstration of how those old fuel systems work.
Old?, thats how they work today.
I want to thank you for this video! My 2000 LeSabre, while hard starting, was running pretty well. It wasn't backfiring like with a leaky pressure regulator. (I'd changed it 5 yrs ago only later to find it had been the subject of a recall a decade before it failed.) While I don't have your tools, I do have a gauge manifold and a small compressor. Following your method, with no external leaks, I determined it must have a faulty pump and replaced it. Inspecting the old part, I found a pin hole leak in the plastic flex line, bleeding pressure back into the tank, between the pump discharge and the top of the assembly. Oh yeah! Bonus. I also now have a working gas gauge.
Hell of a great video! Well explained and now I know how to check the system better! I have a few more issues to check before ripping out the pump. Appreciate your knowledge! Keep up the great work buddy!
Another great South Main Auto Repair - Eric O video! Excellent examples on how to systematically go about diagnosing a fuel pressure problem.
This is an amazing mechanic! Very good Sir, and you’ve helped me to go somewhere with an issue I’ve got on my older f150 with a 4.9 EFI. Thanks so much Sir! Wow, yes it was definitely spraying like wide open like no injection was there like you have equated on this video! Never will have thought an injector could as you say leak the volume it did… just wow, wide open like not there…
Great video showing the logical steps. I think the BMW N63 V8 had a similar issue with a failed injector hydrolocking the engine and destroying it (with dealers charging $25K+ to replace the engine). The ECU monitors the fuel rail pressure and could, if manufactures wanted, detect a key on no-crank injector leak and then throw a code and prevent you from cranking the engine. When you shut your car off it could easily detect a fuel rail leak and
throw a code and even perhaps prevent cranking until the code is reset.
That's a bit extreme but it might have saved BMW, and apparently GM,
some engine replacements. And the injectors should be designed even if stuck open to limit the max flow to something that hopefully wouldn't hydrolock an engine just from the 2 second fuel pump prime and then being cranked. But yeah, at this point this Caddy is basically scrap.
I like your plumbing setup on your fuel pressure gauge. Like they say, necessity is the mother of invention.
So glad you picked my car. 2003 Cadillac Deville has the same coil pack and configuration shown on top of the engine. After having replaced the intake manifold gaskets on a 1999 Chevrolet Malibu LS , it took me seven months cause I’ve never done that sort of work before, I was elated to do the Cadillac Deville job in 3 hours. I gave up on replacing the gaskets as I noted in my last comment -they kept popping off. But the car is relatively easy to work on. I’ve replaced a wheel bearing assembly. I wish somebody would make a video about how you get the wheel bearing through that hole without breaking off the ABS sensor or whatever the hell that gizmo is that sticks out and breaks off. I used to play with Rubiks cubes and these wooden puzzle cubes so I tried every combination I could think of, but could not get that wheel bearing assembly through the hole with without breaking off what I thought was the ABS gizmo. I also gave up on replacing the fuel injector O-rings that have 106,000 miles on them. There’s a plastic ring at the bottom that keeps the O-ring 1/8 inch off the bottom. The Fel-Pro O-ring replacement kit does not have those plastic rings. If you try and take the O-ring off you break the plastic ring. And working on the Chevy it was impossible to replace the fuel injectors because the clips that hold the injector to the rail would go flying and get lost somewhere in the engine. So that was a job that never got done. I got all these Amazon fuel injectors that will never be used because the clips are so horrendous. I did not try the clips on the Cadillac engine. Everything on the Cadillac is so much better than on the Chevy for being easy to work on. My biggest gripe about the Chevy is the AC has never worked right. The 1999 Chevrolet Malibu seems totally accessible for the AC components except the condenser. If you look at the Cadillac condenser it looks like you just open the hood and out it pops. Not so with the Chevy. I find the Chevy is a nuisance to work on. But the Chevy gets 20 miles per gallon with a leadfoot in city driving. The Cadillac gets 14 at best. The Chevy is ideal for city driving and shopping trips. The Cadillac with the starter motor buried under the Plenum is better designed for interstate driving.
Happy-go-lucky. It seems like in one of Eric's Clips he was working on one with those clips that hold the injector to the fuel rail and it was determined that they were only on there to keep the injectors from falling off during assembly at the manufacturer. I would have been the same engine as yours
The new Northstar firehose injection system-!
yambo59 that's hilarious!
This is too much of a coincidence. Im currently dealing with residual pressure lost. Thanks so much for video.
Awesome video... I've been looking for ways to determine why my LS won't hold pressure with the key off. Unfortunately I don't have one of those T fittings. I believe my issue is either the pump check valve or pressure regulator.
seriously this video is very informative. very precise diagnosis. thank you eric o. thank you very much for great stuff.
Eric O. This is an excellent presentation into diagnosing an event I have seen to date. No one does them better. Process of elimination was right on. Don't want to sound like a brown noser but, you are my hero. All that in twenty minutes. if your not getting paid somehow on these videos, something is wrong in internetville . Bless you sir.
💯💯💯💯💯💯💯💯💯
Agreed. One of the best diagnosis videos I've seen on the Tube. Thx for posting it!
3es ree redd er by ßßaaaaaaaaaaaaààààßaasaaaaaàaaàaàaaaàaaaaaaaaaaaaaàaaaàaaàaaaàaaaaaaaààaaaaàaaaaaaaaaaaaaaaàà sea aa area At
Eric
i got home late and got on the pc and was like damn ,.....no sma videos....and then i hit refresh and bam! you uploaded one.
Timing perfection.
Great methodical diagnosis Eric.
"Safety squints" Your funny expressions are one of the things that make your channel so much fun.
A nod to AvE for sure. 🤘
i like the term "Bitch Mittens" aka gloves.
Thank you for your thorough demonstration of isolating this problem. I really appreciate your methods and presentation!
educational as usual Sir Eric. Ive got a vauxhall (General Motors) Astra active 1.6 inline 4 with fuel injectors similar to those on the cadillac .I ve had problem with the upper sealing rings blowing out cause over presure at the pump in the tank.
The word is deluge. It deluged the cylinder. And if Hannah had not have shut her down it would have deluged SMA with fuel. Excellent and another enjoyable video to watch Eric. Thank you so much !
arciefan I wonder if that injector came off of an engine running nitromethane? Had the flow rate!
thank you for this video. It thoroughly explains in logical fashion how to diagnose a fuel leak. Please keep up the good work.
thats crazy! never saw an injector leak that bad either! great video as always keep them coming! wow that injector is crazy
Awesome diagnosis sir....1st class !
Great job explaining the three places fuel could go! Keep up the good work on your videos.
the most complete diagnosis discussing the several possible options for the fault. this helps a lot., Thanks !!
I’m gonna try this on my Pontiac 2.4 1998 GT. Same exact issues, Loss of pressure slowly going to check everything you did in the video. Thanks much I wish I had a mechanic in my area like you
Good call; good practical procedure to follow, but no Brake Kleen, no acetylene torch, and no explosions to liven things up. I guess you noticed that beginning at around 2:20 or 2:21, you can see gas dripping out of the T-connector at the point where you connected it to the pressurized fuel line - it happened each time you turned the fuel pump on. That little glitch could throw us DIYers off the correct diagnostic path.
Great video. Perfect timing for me to see this one because I'm currently dealing a similar situation on a 1989 F-350 dually with a 460. This will help guide me to thru the process to narrow down what my issue is. Thanks a bunch for showing us this process.
Great video! Good editing. To the point. Made the diagnose look easy
there's your problem lady
Wow that's amazing the flow rate of that injector. Again awesome video Mr.O
This guy has the best informative videos. I'm still catching up on all of them.
Epic injector fail for sure Eric. Sweet catch on video! Lots of good info in this one. Thanks!
My '79 Caddy Seville EFI Olds 350" had that problem... getting 1 MPG... raw gasoline dripping out the end of the tailpipe... Caddy wanted $180 for a new injector, so I blew air through it backwards from an air hose while jumping it open with 12 volts and it cleared the clogging crud out of it... worked fine there after... still have the car... Caddy wanted $400 for pair of new rear air shocks, so bought universal ones for $50/pair... Wanted $90 for front muffler and $60 for rear resonator, so put four $15 turbo mufflers on it... quieter than stock and less back pressure!
im a huge fan of your show i have bin wrenching for over 20 years and im still learning new things with your show
brilliant was just dealing with a neighbours car with low pressure fault only reading 0.5 bar! new in-tank pump with built in regulator solved it cheers Eric, sandy
Great video. You make it so simple to understand. I am getting a p0171 and p0174 code. I was thinking weak fuel pump as the regulator seemed to be working, when vacuum line is disconnected the pressure goes up with no leaks. When car is shut off the pressure drops. After watching your video and seeing how you pinched off the return line l did the same. My pressure was much higher than when the car was running and it was maintained after the car was shut off. Final outcome was a bad fuel pressure regulator. Much easier to replace than a fuel pump. Thanks a million for your video. Doug in Canada
You are The best car UA-camr! Thank You so much for Your videos, that I can learn from!
You are Very thorough and it is nice to learn from someone that diffenly knows what to do. I greatly appreciate watching your videos. Thank you
Great Video Eric, you are always a step ahead of me:) I was thinking that a thermal camera would be a good way to see if an injector was staying energized by seeing which one was hottest, but then you mentioned the thermal camera! I was also thinking that seeing which injector was COOLEST (due to the fuel flowing through it) might be a quick way to pin down the culprit.
I've been chasing my tail. I hopped up an LQ9 (basically an LS2) a bit with a custom valvetrain, cam, Johnson Lifters, rocker rollers... Then threw it in my 2001 Tahoe. Engine runs like a BEAST no issues (except P0300 code on occasion but due to bigger cam?) Bought new Delphi injectors (I now see they have very BAD reviews on Amazon). Long story short. I can warm the engine up. Then turn it off and say go in the store. When I come back it doesn't want to start. I have to crank the engine for several seconds before it will turn over. It starts perfectly under all other circumstances. I've been chasing my tail trying to tune issue out with no luck. Bad injector? I am buying stuff to diagnose. Bit nervous to pulse injector in cylinder w/ engine off like some tutorials I've seen. Have to finish watching your tutorial.
I enjoy your videos. I like the problem solving logic as well as the close ups. I'm a little hard of hearing so the clarity of the audio is important to me.
Great video Dr. O! Just had a Yukon on Friday doing that exact same thing, customers bringing it back Monday now I have a new approach for it. thanks for all the helpful information.
Excellent excellent video this individual does an excellent job in explaining so much in almost less than 20 minutes.
Eric you're my hero I just love watching your mind diagnose things. You're my mentor. Thank you hope we can meet someday
Thank you for making this video was chasing my tail trying to find fuel pressure loss - ended up being bad fuel pressure regulator.
Take off the vacuum line and if there is signs of gas fuel pressure regulator always the issue in this case
I'd tell the customer that there's no guarantee that it will work. because an injector leaking that badly might have caused cylinder damage not to mention engine damage in general. and knowing this they could purchase another fuel injector? (preferably a used one). because the vehicle is not worth spending a lot of money on. and clear the cylinder in question of fuel by cranking it over with the spark plug out. and then the replace the injector and put the spark plug back. then fire I up and see what happens. if it runs any better (pretty unlikely) then change the oil and drive until it dies.
I enjoy watching your diagnosis....you make
What you're doing look easy. Your experience has obviously been gained through many hours of work. I only wish I could find someone like you to fix my car in barrie Ontario Canada!
Thanks and ( look out scotty ) this guy knows his stuff too!
Look out Scotty if you are talking about Scotty Kilmer he has never put out a video near as good as Eric. If he does know as much as Eric he has never shown it in a video I have seen.
Your the man, We look on and feel like top notch mechanics till we see our problems somewhere else’s,
Great video Eric. Never seen an injector leak like that before!
Man I learned a lot...I'm working on a Polaris Ranger and all your information enabled me to fix it and I thank-you!
Great job of troubleshooting. I am currently trying to figure out a cyl 7 misfire situation on this same engine. I have replaced spark plug, boot, swapped coil assemblies and it stays with the cylinder. I have 35psi fuel pressure with key on and at idle. Misfire counters are worse at idle than higher rpms. I have replaced the fuel pump for a bad sending unit. The low fuel pressure concerns me. Any thoughts. Thanks Eric for sharing the knowledge.
One of the best videos I have seen on this subject.
You did a great through video and covered all the fuel diagnoses bases well done and thanks, Old retired wrench!
Good find Dr. O., if it was mine a trip to the salvage yard.
Just about to get started on my 2001 Nissan Xterror with a hard start when warm.... that was an epic discovery of the leaking fuel injector! Damn son!!!
"Holy Crap Biscuit!" -- that was a thoroughly enjoyable romp through learning some cool stuff!!! Great video and you're a pretty clever guy!!!
using "holy" and crap together is an oxymoron....
Instead of pulling the injector rail and the injectors like you did, could you not pull the plugs and check for one that is fouled with fuel? You're going to have to pull at least one to overcome the hydro lock in any case.
I'm using the last segment tomorrow! Awesomeness!!! Spewing is the descriptive word that I'd use for that injector!
Excellent video Eric O !!...I picked up 2 used GM fuel line adapters (J37287 ) on Ebay for cheap...less than $100... each has the inline shut off valve....no more pinching off the lines with vice grips !!
Have a car IDENTICAL!!! to this in my stall right now. I remembered watching this a while back, and had to find it again tonight. Can't wait to get there in the morning and pull my injector to see if it sprays like this one did.
This gets a lot more fun when you have nylon lines, rather than rubber. :D
Smack the injector with a hammer, bill the customer for an engine replacement, and ship it!
"Deluge" would be the magic word you were looking for.
Good Diagnostic testing!
You found the gusher!
You are wickedly nice at what you do bro. Respect ✊🏿
It's a Cadillac, it supposes to run rich since only rich people buys Cadillacs.
Mine runs poorly 😜
Upallnight HEY! I resemble that comment.
Cadillac: The poor man's benz!
LOL and poor people love Cadillacs that may be the reason they are poor???
Thats right buddy, all that comfort NEEDS that power, I tell ya what, them Caddy Lacks pass everything on the road, mmHmm, except a gas station! Ha! I know thats right!
This is the best testing procedure that i has ever seem, i really enjoy it thanks for the info.
I’ve learned so much lol thanks I’ve filed that away...I just watch random videos by you just trying to get better at diagnostic
Just the video I was looking on how to test the fuel pressure regulator part. Thanks for sharing
Great video Eric. Could be b/c it's 5am at the moment, but would you mind clarifying why unplugging each injector and then running the pump is test of the PCM?
Awesome Diagnostic video Eric !, Keep up the great Content, Even As a Certified Tech It helps to be shown other ways of Diagnosing !
Introducing the all new General Motors Northstar Rich Edition!
*Replaceable Head gaskets still included!
Buy one now!
Sorry I just had to say it! Incredible work as always!
Bro you are a BOSS. I hope I can get to your level of experience and knowledge someday. Thank you for sharing
Bar engine over to relieve cylinder hydo lock. Man that brings back old memories of hydro locked Cummins truck motors which had holes in the liners from cavitation filling cylinder with coolant. To evacuate lock up bar engine in reverse engine rotation, thus allowing the fluid to escape out the exhaust value. After 3 or 4 rotations the cylinder is cleared allowing engine to be started, leave radiator cap loose and haul another load of logs.
So bar reverse rotation to expel fluid.
Thanks man, learn a lot with this video, now let me go to my 460 and check all the injectors, thank you.
So what all symptoms can a fuel pressure leak down cause? No start? Slow to start? Huge loss of power? Thanks for the video!
Having the problem with 1997 Tacoma, replaced all injectors. Going to do pressure regulator next. Starts hot fine and runs good, cold start hard and have seen a little gas leakage around regulator.
Nice job Eric. Definitely a major leak going on there
Its so bad to let a car sit for years everything dries up and doesn't work. But thats where Eric O. comes in and saves the day.
Awesome video - love the clear explanation - thanks Eric O!
Is that a Ca-Dilly-yak? Well there's your problem right there lady!
So glad I watched this video. So much great information. Question, could you have removed the plugs and turned the engine over and looked for the cylinder shooing out fuel.
Wow! That's a bad injector! Great video! Thanks for sharing!
great work Guys...
now if I just had all those tools
Can't learn this stuff in school, nice work
very good information you made it so simple . never seen a injector spray that much wonder if the end is blown out
You rock as always. Saying hi Eric O from central Louisiana you the man.
"There's your problem lady", lol. Great video Eric. Nice call on not cranking that thing over. Talk about hydrolocking jeeez!.
Eric you are my mentor and trainer!
Had this problem on my son's '02 Silverado and replaced the regulator and no improvement. Decided to replace the fuel pump thinking it was a check valve in the pump. Turned out to be the flexible plastic line on the pump unit had rubbed on one of the pump support rods and developed a pin hole.
very informative and in depth fuel diagnostics