I have a question I'm looking for a rc drift car 1/28 I have lots of experience with rc cars. And I would prefer rwd and large steering angle and I don't know what one to get
@@kaydenmosley538 There are many good cars nowadays. At the top we have DriftArt 2, GLD, Atomic DRZ V2 and XRX DPA. BMR-X is also good but it's 1/24 for using scale model as the body. The first choice is DriftArt but it could be difficult to find (try helidirect). DRZ V2 and GLD are more widely available. My personal favourite is the GLD but it takes a lot of expensive upgrades to work right. Hope this helps.
@@BeaversHobby thank you so much I am very grateful I do love both the drift art and the atomic but before I stumbled apon your channel I picked out the hgd1. Is that a good car to start with
@@kaydenmosley538 HGD1 is also good. I's not as advanced as other cars and might take some tinkering to make it work. The good thing about it is that you can use springs and differential directly from Mini-Z AWD so it's easier to find parts and tune than other cars.
@@BeaversHobby thank you so much but after some more thinking I think I will go with the atomic drz v2 but I have having troubles finding what electronics to put in it so I just got the same electronics as your normal one hopeing they fit in the v2. Unless you have so recommendations.?
@@nado121 I went and check the Caddix, is this the one with a small camera and a box? If so then yes, it'll work. The only thing that will be too big is the full size action cam like GoPro Hero or Yi4K. A small FPV system will work just fine. A cube camera like GoPro session will also work.
To move the steering rod to the upper hole on the servo arm what I did was put a bit of CA glue on a thin toothpick, smear it into the hole that’s too large and then gave it a drop of accelerator. After that the stock screw tightened into the hole nice and tight.
Beaber , i need help man, Anyone knows how i can plug and play with 284131 new stock electronics a gyro? The one i got has different pin connectors looks like jst 1.5 but i think are not exactly because i got micro gyro and the connectors are white and small but different from stock new receiver and servo that it's physically impossible to connect... I dont want to cut and soldering servo wire and gyro to receiver wire to change from 284131 type to more standard type, help me please!!
The gyro is JST ZH 1.5 while the car is JST SH 1.25mm. If you want to keep the original plugs (probably in case you want to use it again without gyro) then you can get some of the ZH and SH parts to make 2 adapters, one is to convert ZH from gyro to SH on the ESC and the other one to convert SH on the servo to ZH to plug into gyro. Otherwise you will need to cut the servo wire and splice that into the gyro cable with 3 wire and use that salvaged head to put on the servo.
Thank you for the review. I did order 2 of this model and I wonder if can 2 same rc cars can be running in the same time ? If not are there any solution ? Thank you
Yes, they can run together at the same time. You just need to start them up one at a time. Here's how to do it: Turn the first car on then turn the first transmitter on and move the steering wheel. Once that's done do the same on the 2nd car. If you have the 3rd, repeat the process on a new one. Do this every time you want to run because this car binds to the transmitter at start up.
😅funny thing - by accident I figured out that the servo was forcing the 2in1 to shut down - luckily I had a right servo - it runs again, and yes it’s fun granate
Personally I don't recommend the velcro because you will have to line it up every time you play and if you use it for touring or anywhere with dust, the velcro will get dirty very quickly. What is the car for? Is it for touring or drifting. If it's for touring then there's no better and more secure option than using clips. However you can make it easier by putting a small cable tie on the loop at the end so you can pull the clip out easier. If it's for drifting then the magnet mount system is also good.
Sorry to hear that. At this price the QC is pretty much non-existence. Still, it's not that difficult to replace so hopefully you can get it up and running soon.
Unfortunately it is not compatible with Mini-Z Skyline bodies. Those cars are 94mm wheelbase narrow bodies while this car is 98-102mm wheelbase ultra wide chassis. It might fit some of the 1/24 scale model although you will need to check the wheelbase on the model if it's 98 or 102mm.
I ordered this vehicle and received different electronics, no standard 3 pin servo, and the radio doesn't center its awful. I would recommend everyone buy the k989 or k986 instead of this truck now.
Here you go. Wheels www.srcc-devils.de/FELGEN/AWD-BZ-GLA-etc/WA-S603W-S6-AWD-Rim-Narrow-1-5-White.htm?a=article&ProdNr=A1664&p=1108 Tyres www.srcc-devils.de/GL-RACING-WORLDWIDE-SHOP/GL-Drift/MDT001-KYOSHO-AWD-Mini-Z-MDT-001-Reifen-1-24-Drift-8-5mm-4-.htm?a=article&ProdNr=5302&p=1221
The diffs are badly made. You can either fix the diffs along with the drivetrain like this ua-cam.com/video/TnhriaSSfSA/v-deo.html . Or replace the diffs like I did in t\his video.
You will need to install your own ESC. This is the tutorial ua-cam.com/video/BSt7U-yOa4Q/v-deo.html I didn't use NB4 in the video because it hadn't come out at that time.
Does anyone know if the stock plastic diffs have any oil or grease in them? I watched videos on how to fix stock diffs,but not sure if they were lubed from factory...thanks
It will over time. There are 2 solutions, 1 is to upgrade the drivetrain with metal bit.ly/3w7XChB so the centre shaft pinion gears are metal and the spur gear as well so the motor gear won't eat it that fast. Or replace the motor pinion with a plastic one. I recommend upgrading the gears to metal because it will prolong the car's life as the pinions are known to wear out very quickly.
i got the k989 few days ago and it has the same upgraded parts as this 284131 expect old transmitter and protocol drive train is sticky of course, i watched your tutorial on how to make it smoother but after doing it my diffs doesn't work properly anymore :|. they do work but has annoying noise like if it was broken or something. also filed the suspension and now the wheels is rolling over and it's undrivable, great job by me. i think i've done it wrong since i'm new to this kind of stuff. i ordered new metal parts as will as drift tires to replace the broken ones and they should arrive in few days and will be ready for drifting soon :)
It'll take some practice to get everything right. Don't get discouraged, stuffs will break from fixing some times and it'll be all the experience you'll get. Best of luck with the project!
Dude, I love what you do. I love your little deadpan sarcastic criticisms too (no, there is no drag brake) haha. Your rooftop would make an awesome track if you could resurface it!
They are the same car underneath. Choose whichever body you like because the new batch of K989 should come with the same upgraded transmitter already. Or choose the 284131 if you are not sure which transmitter you will get.
Yes, it's removeable. However it is a part of the rear gearbox that props the gearbox in place. Originally (in K989, K969) this was a small plate so you can cut all the diffuser out to keep the car functioning properly.
Sorry me again commenting again lol. Today the car stopped working the wheels turn by the motor have stopped going forwards and back wards 😢. ? Think I am just going to buy a mini Z
Do you hear any buzzing noise (or faint beep) from the ESC or not at all? If you don't hear any beep I'm afraid the ESC portion is fried and you can't fix that. Only to replace the whole box or upgrade the electronics. If you are comfortable with changing the electronics then it will open up more settings than getting a Mini-Z. But if you want the simplicity, pick up and play aspect. Mini-Z is still the best.
@@BeaversHobby yes I am afraid the Esc is fried now nothing happens 😂 but yes I like the simple and good things in life so my Mini z be arriving tomorrow 😀
I have this version...its a great car...i ordered some metal diffs,but not sure the plastic gear will hold up..on the fence on installing...i may just do plastic diff fix and add some grease first...thanks for sharing
The ones I got from Aliexpress are really good www.aliexpress.com/item/1005001671065507.html You will have to use them with long CVD though. Here's banggood link bit.ly/3m1i4bd but you should be able to find the same on Aliexpress too. You can also buy only the front one way and glue the original rear diff to make a lock diff if you want to save a bit of money.
Out of the box with the drivetrain is very sticky and you will have to pull the throttle a lot to start rolling. Also, if the DR knob is turned down then the throttle will take a lot to start responding. You can disassemble the car and run only with the motor outside to see if the deadzone is still there. If so then there might be a problem with your electronics.
I just got mine and it turns on, the lights turn on, the controller turns on, the steering works but it won’t move at all. And suggestions or should I just return ot
Make sure the battery is fully charged or have at least 6.8V. Check the TH DR (throttle dual rate) dial on the transmitter. It's the bottom dial. Turn it up or the other way and see if the throttle works. If not, check the motor connection if the wires are OK and not cut. If nothing works the car might be faulty so you'll have to contact the shop for a replacement or refund.
Sounds like the charger is broken and won't charge the battery. If you have a multimeter or anything that can check battery voltage it'll help to check if the battery is charged or not. Anyway, do you have another charger to try?
So a big thanks for this 👍🏾 loved the video so enjoy another subscriber! Bought 3 x 7.4V 600mah batteries to go with this ... And the full metal upgrade kit with shocks and wheels ... And looking for a decent set of drift tyres. Please please please do more with this and i'll follow your journey! Need to make this a decent drifter 😂
Was it worth adding full metal parts. Didn't it make it a lot heavier ¿? I was also looking bigger battery but stock battery last 18 mins ?? Seem like fair good run time .. haven't got mine shipping is slow .. hopefully couple weeks it turn up
Hobbyking has 300-450 Turnigy nanotech. 300mAh will fit without modifications, 450 will need some. You can also get GNB battery from many sources like Banggood. I use the hi-voltage series. 350mAh bit.ly/3ov4DDz seems to be out of stock right now so here's 300mAh bit.ly/3ihR6g3 . None of GNB will have the plug you need for this car (JST RCY) but you can convert it to anything so there's no problem.
Yes, it will. It's the same car after all. You'll have to adjust the body posts a bit and it'll fit. I believe the front and rear bumper are now available too so you can fully convert K989 to 284131.
Sorry for the later reply. Turn the car on first, then the transmitter and move the steering wheel. If that doesn't connect to the car then something is defective and you should contact the shop.
@@CitadelPhotography In malaysia, i still didn't get it. I asked the Wltoys official store on a online platform and they replied the esc wont bind into your transmitter. Idk y they said it but ik we can bind it with the esc and 144001 transmitter. I planned to change it bcs my k989 stock transmitter is giving the same prob everytime. But i buyed a new transmitter for my k989. ( stock ) Hope it gonna be good.
The motor size is called 1410 or 1625 depending on the brand. I usually recommend a budget motor: Surpass Rocket V2 for Mini-Z www.aliexpress.com/item/1005002433453641.html 3500KV or 5500KV is the most optimal. As for the ESC, can't go wrong with DasMikro V3 www.aliexpress.com/item/1005003527519554.html . Here's one of my build videos. ua-cam.com/video/j9pO35iaqfo/v-deo.html Don't worry, K989 is the same chassis. Just different body.
Does anybody know what voltage the LED lights are running on? I want to use an AIO FPV camera that works on 3V to 5V. My plan is to unplug the LED and than use the plug to power the camera instead.
Hey Beavers, I got my first RC car as an adult for my 30th. Got a K989 and I've been watching all of your videos since. Do you think the recommended parts get re-stocked often on Banggood? The differentials and pinion gears are currently showing as out of stock to the UK
The pinion gears get restock pretty often but I don't recommend the differentials. It's better to get the long CVD 25mm or 27mm and use Mini-Z AWD differentials instead. As for the spare parts, take a look in aliexpress too. The shops there restock faster than banggood.
Hi, I’ve just received my car, and I have a problem with the car only steering and having no throttle. I’ve tried everything, nothing works. Do u know a way to bind the receiver again?
If the steering works but no throttle, make sure the battery is fully charged. Then check if the Throttle D/R knob is turned to the right direction. Hold the throttle and turn the knob to see if the motor runs, I think it should turn clockwise for max speed. The way to bind this receiver is turning the transmitter on, turn the car on then move the steering on the transmitter.
@@BeaversHobby Hello, I’ve charged the battery fully (I even checked on a lipo checker). I also tried turning the dual rate, that also does nothing. Lastly, if I turn on the car and the radio, it doesn’t bind automatically. I need to every time turn the steering wheel. Then it is bound, but still no throttle. I was thinking that the receiver maybe is broken.
@@Tiickel You'll have to bind it manually every time you turn the car on so that's normal. However I think your receiver-ESC combo is faulty. Please contact the shop you bought it from for replacement.
I have this car with this problem...turning circle to left is very tight but to right is not...radio trim is centered and servo arm in correct pos. 🤔 any ideas thanks.
After you centre everything check if the servo can swing both sides equally, if not then re-center the trim then take the servo out and re-position the servo horn. If the swing to both sides are equal then it's the problem with the wheels, tyres and the suspension. See if you get the tyres contact the same on both sides. If not you might have to put M2 screws in the lower arms to adjust the ride height and contact. Also check out stage 1 and 2 for how to inspect and fix the car. ua-cam.com/video/TnhriaSSfSA/v-deo.html ua-cam.com/video/QAGTXo70MmU/v-deo.html
@@BeaversHobby I would love a gyro installing. I am not very good with soldering however. I was going to ask if I send you my car can you install it I pay you cash??
Is there a way to reverse the throttle? Mine came new with the throttle control backwards. Everything looks to be installed correctly. Thank you for your videos. They are very helpful
Check where the problem is first. If you can pull the trigger, push it to go one way then come back to centre again and push to go the other way then the problem is at the motor wire. You can swap the polarity easily by using a tweezer to push the tap on the motor plug down and pull the wires out then you can swap them. If you pull the motor plug out you'll se one side with the lock and the other side with the exposed terminal. Do it on the side of the terminal. It doesn't have to be a tweezer, anything thing enough can push that terminal down and you can pull the wire out. If the problem is not at the motor wire, the wiring inside the transmitter is reversed. You will have to swap 2 of the 3 wires in the throttle potentiometer. Not sire which one so you will have to experiment which of the 2 wires give you reverse throttle.
@@kaiotech5902 Yes, you can file or mill the original gears down to something like 2mm peck and use the motor gear from Tamiya Mini 4WD (or a plastic 8T gear) over it then glue it in. I did that and it lasted much, much longer than the original plastic gear.
Just bought one of these bad boys. Waiting for it to arrive. I want to upgrade the diffs, front to a one way and rear to a fixed. Mini z ones or copies. And I right in thinking I only need the longer front drive shafts and I can use standards in the rear? If so is the an up to date list of where I can get the parts in the UK. Is there a steering angle mod you can do? I like the look of the carbon chassis and upper deck are they a direct replacement?? Seen some carbon shock towers to? Thanks 🙏🏾
The one way I got from Aliexpress is really good. However if you don't want to wait a very long time then get a genuine Mini-Z parts within the UK. And yes, you'll need long drive shafts for the front with one way. Both can be found in the UK from www.rcm8.net/ . At the back you don't have to get a solid axle, you can just lock (glue) the original axle and it'll work. You don't have to change the rear swing shafts either. The steering mod: follow this tutorial from 5:38 ua-cam.com/video/zB3pUN9XiSw/v-deo.html . Caron chassis is not recommended. It'll mess up your ride height. However feel free to try. Carbon shock towers are good. It should be in aliexpress so I don't know if there's any UK stock.
Great video, I got myself one of these as well! How did you remove the pinion gear in the end? I can't pull it off for the life of me and I wonder whether there's an easy way to do it.
It's on banggood and aliexpress. Banggood seems to be out of stock right now so here's the Aliexpress link. www.aliexpress.com/item/1005003674363056.html I recommend using Mini-Z AWD differential in conjunction with the long CVD www.aliexpress.com/item/1005003399026933.html for better durability and fitting. Also with the long CVD you can use any Mini-Z AWD compatible diffs like ball diffs from GL Racing GLA and get the best performance out of it.
Hobbywing Quicrun 1625 should fit the tall bit of the cockpit nicely. You'll have to change the transmitter too following this guide ua-cam.com/video/BSt7U-yOa4Q/v-deo.html . Still, have you fixed the drivetrain before running, it's so sticky that it might burn the electronics out.
Good video! I'm about to purchase two of the WLToys version so I can force people to race me. Am I correct in understanding that I can swap a car body onto the truck version? I was going to buy one car and one truck just for the difference, but it seems the truck has better upgrades already and I'd hate to buy something not as good over a body.
That'll do. I'll test later which CVD you need. The 10.5mm for Mini-Z wide chassis might be too short for Mini-Z diff. Usually I use the long CVD bit.ly/3m1i4bd with Mini-Z ball diffs.
Could the stick drive train be the reason my car stops responding to accelerator and only leaves me with steering control and no forward or backward movement after a short drive? Is someone freezing/locking.
@@shrimperlincs3395 Do you hear anything when pulling the throttle, like a beeping noise or the motor is trying to spin? You can also try and move the wheels by hand and see if the wheels can spin. If the wheels can spin alright, it's the electronics. If the wheels are too tight to spin, it's the drivetrain.
Hello Beaver, great review. I am fan of your RC car videos they are so amazing and easy to understand. I am beginner and want to start this hobby, Can you please create a drift car build series with this car. Also if possible share parts from either aliexpress/bangood.
You can mod a transmitter that has PPM output with multiprotocol and use XK X420 protocol. If you want a ready made one I'm afraid there is no pistol grip or car transmitter, only air transmitter like this bit.ly/3BN6Qik . I also have a series showing how to configure it to use with cars. ep1 Unboxing, basic setup ua-cam.com/video/vSRR67jMhzI/v-deo.html ep2 Self-centering stick ua-cam.com/video/wKuwODFd338/v-deo.html
It's not reliable even in this new version. It'll need some fixing to work and will still wear out quickly. I ended up replacing the diffs with Mini-Z diffs.
@@philipbrits2984 Yes, those are what I use. You'll also need the long CVD for it to work because this is a wide chassis and on stock setup they just extend the outdrive instead of making longer CVD shaft. By the way I just checked and Mini-Q diff is out of stock right now. You can get this instead. It'll be all metal diff. www.banggood.com/custlink/KGmCaD6y0r
Hi Beaver thanks a lot for your fantastic channel and all the information you share with the public. I want to get my fist 1/28 car. I have a lot of experience and know RCs very well, just never tried anything this small. I want to put together some kind of rally car, possibly a kit, certainly with custom electronics, something that can cope with dust and can be used outside. Any advice? Also I need advice about ESC and brushless combo, something on banggood? And TX and RX what is the best micro receiver and what TX will it use? Tnx
For using outside your best bet is Wltoys K989 or 284131. Unfortunately they don't sell this car as kit so you'll have to work it from RTR. Any transmitter will work providing you have a small enough receiver to fit inside. The antenna-less receivers from Sanwa or Flysky Noble (FGr4S) will do nicely especially the Noble because it's dust proof. If you want a small receiver then you'll need Futaba with S-FHSS/T-FHSS, Sanwa with FH3/FH3 or Flysky Noble. These transmitters have receiver (or compatible receiver in case of Futaba and Sanwa) with JST-ZH plug so you can use Atomic or GL brushless ESC directly without plug conversation. As for the motor, take a look at BYRC on AliExpress as they have enclosed brushless so you can run outside safely.
@@BeaversHobby Hi thank you so much for your answer I really appreciate your help. Today I bought the 284131, although I don't like the body. But the car will slowly be upgraded. For now I want to see test drive the car etc, but I the NB4 seems a solid choice for less money. What do you think about Furitek brushless combo? I watch your review and to me they seem pretty good as a company. Also have you ever heard of Carisma GT 1/24 series? The GT24B (kit version) would be my first choice to drive outside but due to Covid regulations etc they will not ship to Europe.
@@flyingformation1878 From what I know Carisma GT24 series is really good. There are RTR around in Europe but as you checked, the kit won't ship to us so that's a big disappointment. Anyway, best of luck with the project!
@@flyingformation1878 The Furitek is very good good but I think it's too expensive to get for only 1 car because of the bluetooth module. If you have many cars then it's more economical because you can share that module.
@@BeaversHobby Tnx again for your help. I checked the BYRC and it seems a very good deal (Combo + Pcard for 29$) it's great to me. For now I will stick to standard electronics and 1 car because I need to see how good they are to begin with etc but I want two or three cars (drifting - touring - and my off road project with the Carisma). I hope you don't mind if I ask some other questions in the future! Thanks mate.
This is a better car just because the transmitter is better. If you can verify that the K969 that you are getting is the new batch with the same transmitter then get the K969.
I have new k969 that arrived last week everything is the same like metal ball head, metal pinion, battery connector etc. The only diff is the controller which is the old big red one. Quick question can i buy the new controller and will it work with my k969? How will i know which protocol and the esc?
![[Quick Review] WLtoys 284010 - All improvements from previous versions](http://i.ytimg.com/vi/9AkwHF-D-zI/mqdefault.jpg)
![[Quick Review] WLtoys 284010 - All improvements from previous versions](/img/tr.png)
![WLtoys K969 [Modified] Shakedown | FOW+CS Mod | DS Racing LF-5 Impressions](/img/n.gif)
Buy it here bit.ly/3m1LLdW
Use coupon code: BG48fc5d for discount. I tested it and it gave me $12 discount.
I have a question I'm looking for a rc drift car 1/28 I have lots of experience with rc cars. And I would prefer rwd and large steering angle and I don't know what one to get
@@kaydenmosley538 There are many good cars nowadays. At the top we have DriftArt 2, GLD, Atomic DRZ V2 and XRX DPA. BMR-X is also good but it's 1/24 for using scale model as the body. The first choice is DriftArt but it could be difficult to find (try helidirect). DRZ V2 and GLD are more widely available. My personal favourite is the GLD but it takes a lot of expensive upgrades to work right. Hope this helps.
@@BeaversHobby thank you so much I am very grateful I do love both the drift art and the atomic but before I stumbled apon your channel I picked out the hgd1. Is that a good car to start with
@@kaydenmosley538 HGD1 is also good. I's not as advanced as other cars and might take some tinkering to make it work. The good thing about it is that you can use springs and differential directly from Mini-Z AWD so it's easier to find parts and tune than other cars.
@@BeaversHobby thank you so much but after some more thinking I think I will go with the atomic drz v2 but I have having troubles finding what electronics to put in it so I just got the same electronics as your normal one hopeing they fit in the v2. Unless you have so recommendations.?
We need to make a drift set up for this too
Someone pointed out in the last video about the light being good for FPV. FPV drift sounds like a really good project.
@@BeaversHobby do you think it could handle a 29g caddx vista or would that be way too heavy?
@@nado121 I went and check the Caddix, is this the one with a small camera and a box? If so then yes, it'll work. The only thing that will be too big is the full size action cam like GoPro Hero or Yi4K. A small FPV system will work just fine. A cube camera like GoPro session will also work.
@@nado121 it would handle that weight no problems. It wouldn't affect driving much if not any
@@BeaversHobby go with tinywhoop cam+vtx
To move the steering rod to the upper hole on the servo arm what I did was put a bit of CA glue on a thin toothpick, smear it into the hole that’s too large and then gave it a drop of accelerator. After that the stock screw tightened into the hole nice and tight.
Hi I Got 3 for For me and my brothers, I Followed your videos! The recent 284131 have metal center shaft pinion now!
For the servo's arm, don't order new ball heads, just use a little bit of crazy glue, it works perfectly
Yay! I LOVE YOUR REVIEWS! Your voice is really nice to listen to!!!
You're funny 😂
This is the best review of this car I saw. Thank you for your expertise and the tips to upgrade this car.
Finally another review :)
Beaber , i need help man,
Anyone knows how i can plug and play with 284131 new stock electronics a gyro? The one i got has different pin connectors looks like jst 1.5 but i think are not exactly because i got micro gyro and the connectors are white and small but different from stock new receiver and servo that it's physically impossible to connect... I dont want to cut and soldering servo wire and gyro to receiver wire to change from 284131 type to more standard type, help me please!!
The gyro is JST ZH 1.5 while the car is JST SH 1.25mm. If you want to keep the original plugs (probably in case you want to use it again without gyro) then you can get some of the ZH and SH parts to make 2 adapters, one is to convert ZH from gyro to SH on the ESC and the other one to convert SH on the servo to ZH to plug into gyro.
Otherwise you will need to cut the servo wire and splice that into the gyro cable with 3 wire and use that salvaged head to put on the servo.
Will watch another fixing videos
Thank you for the review. I did order 2 of this model and I wonder if can 2 same rc cars can be running in the same time ? If not are there any solution ? Thank you
Yes, they can run together at the same time. You just need to start them up one at a time. Here's how to do it:
Turn the first car on then turn the first transmitter on and move the steering wheel. Once that's done do the same on the 2nd car. If you have the 3rd, repeat the process on a new one.
Do this every time you want to run because this car binds to the transmitter at start up.
I wish Wltoys could make a 1/10 exactly like the k989 with bigger electronics. Will be a cheap price as k989 for the perfomance and quality
😅funny thing - by accident I figured out that the servo was forcing the 2in1 to shut down - luckily I had a right servo - it runs again, and yes it’s fun granate
Glad you got it working!
Any good ways to mount the shell (and battery) without using clips? I keep losing them. Thinking to try using velcro but not sure where to mount it.
Personally I don't recommend the velcro because you will have to line it up every time you play and if you use it for touring or anywhere with dust, the velcro will get dirty very quickly.
What is the car for? Is it for touring or drifting. If it's for touring then there's no better and more secure option than using clips. However you can make it easier by putting a small cable tie on the loop at the end so you can pull the clip out easier.
If it's for drifting then the magnet mount system is also good.
Bought one like you and others suggested - done all your drivetrain and suspension mods for just 12 sek of runtime - esc dies - good value 👎🏼
Sorry to hear that. At this price the QC is pretty much non-existence. Still, it's not that difficult to replace so hopefully you can get it up and running soon.
Hi Beaver, is it possible to fit some kind of Skyline (R34 R32 or the OG Hakosuka) body on this? One that I can get in Europe? Thanx!
Unfortunately it is not compatible with Mini-Z Skyline bodies. Those cars are 94mm wheelbase narrow bodies while this car is 98-102mm wheelbase ultra wide chassis.
It might fit some of the 1/24 scale model although you will need to check the wheelbase on the model if it's 98 or 102mm.
I ordered this vehicle and received different electronics, no standard 3 pin servo, and the radio doesn't center its awful. I would recommend everyone buy the k989 or k986 instead of this truck now.
Sorry to hear that. I didn't know they would change the components.
Greetings from Germany. Can you put a purchase link to drift tyres for the Wltoys 264131
Here you go.
Wheels www.srcc-devils.de/FELGEN/AWD-BZ-GLA-etc/WA-S603W-S6-AWD-Rim-Narrow-1-5-White.htm?a=article&ProdNr=A1664&p=1108
Tyres www.srcc-devils.de/GL-RACING-WORLDWIDE-SHOP/GL-Drift/MDT001-KYOSHO-AWD-Mini-Z-MDT-001-Reifen-1-24-Drift-8-5mm-4-.htm?a=article&ProdNr=5302&p=1221
I just got one. Drivetrain is way too tight. Looks like the gear mesh cannot be adjusted.That sucks.
The diffs are badly made. You can either fix the diffs along with the drivetrain like this ua-cam.com/video/TnhriaSSfSA/v-deo.html .
Or replace the diffs like I did in t\his video.
Any idea if this can work with Nobel Nb4 Transmitter
You will need to install your own ESC. This is the tutorial ua-cam.com/video/BSt7U-yOa4Q/v-deo.html
I didn't use NB4 in the video because it hadn't come out at that time.
Thanks for this video
My differential broke any suggestion for a cheap but better differential?
Mini-Z AWD differential but you'll have to replace the CVD with long ones like these. bit.ly/3m1i4bd
This is more my language
3:10 thanks dude, now im know function of mode 1234 button 👍👍
Does anyone know if the stock plastic diffs have any oil or grease in them? I watched videos on how to fix stock diffs,but not sure if they were lubed from factory...thanks
Unfortunately, there's no grease in the stock diff.
Thats good to know.thanks
A question my friend,the new motor metal gog wont eat up the plastic one that interacts with it?And is there any solution to it if its true?
It will over time. There are 2 solutions, 1 is to upgrade the drivetrain with metal bit.ly/3w7XChB so the centre shaft pinion gears are metal and the spur gear as well so the motor gear won't eat it that fast. Or replace the motor pinion with a plastic one.
I recommend upgrading the gears to metal because it will prolong the car's life as the pinions are known to wear out very quickly.
i got the k989 few days ago and it has the same upgraded parts as this 284131 expect old transmitter and protocol drive train is sticky of course, i watched your tutorial on how to make it smoother but after doing it my diffs doesn't work properly anymore :|. they do work but has annoying noise like if it was broken or something. also filed the suspension and now the wheels is rolling over and it's undrivable, great job by me. i think i've done it wrong since i'm new to this kind of stuff. i ordered new metal parts as will as drift tires to replace the broken ones and they should arrive in few days and will be ready for drifting soon :)
It'll take some practice to get everything right. Don't get discouraged, stuffs will break from fixing some times and it'll be all the experience you'll get. Best of luck with the project!
Wise words. Thanks!
Awesome vid mi familia 👍
I subscribed 🙏🏼👍👊🤣❤💯
I still wish they never stopped making the A202(The best of all time in these sizes. WHY they stopped making it is BEYOND me.)
I'm confuse in two cars k989 and 284131 both wltoys which one best??? plz tell 😊😊😊
They are the same car but 281431 has a better transmitter so it's a better version.
Dude, I love what you do. I love your little deadpan sarcastic criticisms too (no, there is no drag brake) haha. Your rooftop would make an awesome track if you could resurface it!
Nice video, my motor runs quite hot after a short while, but haven't done any of the fixes yet.
I'm looking for a budget drift car with possible upgrades and I'm stuck between these to models
248131 or the K989
Which one would you recommend
They are the same car underneath. Choose whichever body you like because the new batch of K989 should come with the same upgraded transmitter already. Or choose the 284131 if you are not sure which transmitter you will get.
@@BeaversHobby thanks for your time and replying, that's a big help..
Great honest review, thank you. Look forward to receiving this truck and checking all the fixes from your comprehensive list. Much appreciated.
Is the diffuser removable to fit a minix body on it?
Yes, it's removeable. However it is a part of the rear gearbox that props the gearbox in place. Originally (in K989, K969) this was a small plate so you can cut all the diffuser out to keep the car functioning properly.
I love your videos sir! Thank you for sharing your knowledge with us. You inspired me to get and mod my k989 :)
Sorry me again commenting again lol. Today the car stopped working the wheels turn by the motor have stopped going forwards and back wards 😢. ? Think I am just going to buy a mini Z
Do you hear any buzzing noise (or faint beep) from the ESC or not at all? If you don't hear any beep I'm afraid the ESC portion is fried and you can't fix that. Only to replace the whole box or upgrade the electronics. If you are comfortable with changing the electronics then it will open up more settings than getting a Mini-Z. But if you want the simplicity, pick up and play aspect. Mini-Z is still the best.
@@BeaversHobby yes I am afraid the Esc is fried now nothing happens 😂 but yes I like the simple and good things in life so my Mini z be arriving tomorrow 😀
I have this version...its a great car...i ordered some metal diffs,but not sure the plastic gear will hold up..on the fence on installing...i may just do plastic diff fix and add some grease first...thanks for sharing
Do you have a recommended front one way and solid rear diff for this?
The ones I got from Aliexpress are really good www.aliexpress.com/item/1005001671065507.html
You will have to use them with long CVD though. Here's banggood link bit.ly/3m1i4bd but you should be able to find the same on Aliexpress too.
You can also buy only the front one way and glue the original rear diff to make a lock diff if you want to save a bit of money.
Hi, the car just arrive, but there's so much dead zone in the throttle. Is it just my problem or has someone else noticed it. Thanks
Out of the box with the drivetrain is very sticky and you will have to pull the throttle a lot to start rolling.
Also, if the DR knob is turned down then the throttle will take a lot to start responding.
You can disassemble the car and run only with the motor outside to see if the deadzone is still there. If so then there might be a problem with your electronics.
@@BeaversHobby thanks i'll try
Have you had the chance to try the metal drivetrain gear set yet? Would you recommend them?
Not yet. From what I've seen it works well if you have the metal diffs too.
I just got mine and it turns on, the lights turn on, the controller turns on, the steering works but it won’t move at all. And suggestions or should I just return ot
Make sure the battery is fully charged or have at least 6.8V.
Check the TH DR (throttle dual rate) dial on the transmitter. It's the bottom dial. Turn it up or the other way and see if the throttle works. If not, check the motor connection if the wires are OK and not cut. If nothing works the car might be faulty so you'll have to contact the shop for a replacement or refund.
@@BeaversHobby Dang ok thanks for the reply looks like I’ll just have to return it.
Bro is it only me or my battery is not charging
Sounds like the charger is broken and won't charge the battery.
If you have a multimeter or anything that can check battery voltage it'll help to check if the battery is charged or not. Anyway, do you have another charger to try?
So a big thanks for this 👍🏾 loved the video so enjoy another subscriber!
Bought 3 x 7.4V 600mah batteries to go with this ... And the full metal upgrade kit with shocks and wheels ... And looking for a decent set of drift tyres.
Please please please do more with this and i'll follow your journey! Need to make this a decent drifter 😂
This is the same car as K989 so here's my 2021 drift setup ua-cam.com/video/j9pO35iaqfo/v-deo.html .
Was it worth adding full metal parts. Didn't it make it a lot heavier ¿? I was also looking bigger battery but stock battery last 18 mins ?? Seem like fair good run time .. haven't got mine shipping is slow .. hopefully couple weeks it turn up
The 600 mAh battery's seem to be fraud .. smaller and weight less than the 400 that come with car. Battery fraud is a way of life with China
Can i use k989 metal parts on this?
Yes, you can. It's the same car with different body after all.
Nice truck can't wait for mine 😀
Does anyone have any idea what the "Mode" Button on the new Transmitter actually does?
It does nothing.
@@BeaversHobby Thank you!
Where do I find extras batteries 🤔
Hobbyking has 300-450 Turnigy nanotech. 300mAh will fit without modifications, 450 will need some. You can also get GNB battery from many sources like Banggood. I use the hi-voltage series. 350mAh bit.ly/3ov4DDz seems to be out of stock right now so here's 300mAh bit.ly/3ihR6g3 . None of GNB will have the plug you need for this car (JST RCY) but you can convert it to anything so there's no problem.
Excellent review with great and extremely useful information!
How did you fix the drive train?
Here ua-cam.com/video/TnhriaSSfSA/v-deo.html
I've got the links for stage 1 and 2 fix in the description too.
Perez Donald Taylor George Brown Mary
Walker Mary White Maria Harris Kenneth
Will the K989 Ford Focus Rally Hootniga will this body of the 284031 truck fit the K989 Rally as I would just buy the body of this truck
Yes, it will. It's the same car after all. You'll have to adjust the body posts a bit and it'll fit. I believe the front and rear bumper are now available too so you can fully convert K989 to 284131.
@@BeaversHobby thanks beaver can you adjust the body posts easily without having to add parts just unclipped adjust etc
@@krisstoney6892 Yes, you can just undo 2 screws and move the post up and down to fit.
@@BeaversHobby thanks my friend.
Je vien de l’acheter et il ce connecte pas à la manette???
Sorry for the later reply.
Turn the car on first, then the transmitter and move the steering wheel. If that doesn't connect to the car then something is defective and you should contact the shop.
Hey beaver! If we use this 284131 esc for k989, can we bind the " M2R " wltoys transmitter to it straight away ?
If it's the same version as the 144001, yes.
@@CitadelPhotography Found this on aliexpress. www.aliexpress.com/item/1005003524383991.html The "Color: 2046" one is the ESC.
@@CitadelPhotography In malaysia, i still didn't get it. I asked the Wltoys official store on a online platform and they replied the esc wont bind into your transmitter. Idk y they said it but ik we can bind it with the esc and 144001 transmitter. I planned to change it bcs my k989 stock transmitter is giving the same prob everytime. But i buyed a new transmitter for my k989. ( stock ) Hope it gonna be good.
How much does it his cost
It's 56.99 USD right now. usa.banggood.com/custlink/GDG5Q6HBM9
May I ask is there any brushless motor suitable to upgrade? Thank you
The motor size is called 1410 or 1625 depending on the brand. I usually recommend a budget motor: Surpass Rocket V2 for Mini-Z www.aliexpress.com/item/1005002433453641.html
3500KV or 5500KV is the most optimal.
As for the ESC, can't go wrong with DasMikro V3 www.aliexpress.com/item/1005003527519554.html .
Here's one of my build videos. ua-cam.com/video/j9pO35iaqfo/v-deo.html Don't worry, K989 is the same chassis. Just different body.
Thanks a lot sir
@@saikeungar My pleasure.
สั่งไปแล้วครับจะเอามาทำขับ4เล่นครับผม..
Thanks for all the advice you put in this video. Very helpful.
I moved my steering arm up with a lot of thread lock
Woow...verg good👍
Thanks BEV i ordered two they coming this week
Does anybody know what voltage the LED lights are running on? I want to use an AIO FPV camera that works on 3V to 5V. My plan is to unplug the LED and than use the plug to power the camera instead.
Usually 3V.
Hey Beavers, I got my first RC car as an adult for my 30th. Got a K989 and I've been watching all of your videos since. Do you think the recommended parts get re-stocked often on Banggood? The differentials and pinion gears are currently showing as out of stock to the UK
The pinion gears get restock pretty often but I don't recommend the differentials. It's better to get the long CVD 25mm or 27mm and use Mini-Z AWD differentials instead.
As for the spare parts, take a look in aliexpress too. The shops there restock faster than banggood.
Thanks for the quick response, really helpful and means a lot
@@tazzoahmed My pleasure.
Hi, I’ve just received my car, and I have a problem with the car only steering and having no throttle. I’ve tried everything, nothing works. Do u know a way to bind the receiver again?
If the steering works but no throttle, make sure the battery is fully charged. Then check if the Throttle D/R knob is turned to the right direction. Hold the throttle and turn the knob to see if the motor runs, I think it should turn clockwise for max speed.
The way to bind this receiver is turning the transmitter on, turn the car on then move the steering on the transmitter.
@@BeaversHobby Hello, I’ve charged the battery fully (I even checked on a lipo checker). I also tried turning the dual rate, that also does nothing. Lastly, if I turn on the car and the radio, it doesn’t bind automatically. I need to every time turn the steering wheel. Then it is bound, but still no throttle. I was thinking that the receiver maybe is broken.
@@Tiickel You'll have to bind it manually every time you turn the car on so that's normal. However I think your receiver-ESC combo is faulty. Please contact the shop you bought it from for replacement.
@@BeaversHobby Thanks for ur help. I’ve contacted the seller.
Thanks for the discount code brother ! ... Ordered mine ! can't wait
I have this car with this problem...turning circle to left is very tight but to right is not...radio trim is centered and servo arm in correct pos. 🤔 any ideas thanks.
After you centre everything check if the servo can swing both sides equally, if not then re-center the trim then take the servo out and re-position the servo horn. If the swing to both sides are equal then it's the problem with the wheels, tyres and the suspension. See if you get the tyres contact the same on both sides. If not you might have to put M2 screws in the lower arms to adjust the ride height and contact.
Also check out stage 1 and 2 for how to inspect and fix the car.
ua-cam.com/video/TnhriaSSfSA/v-deo.html
ua-cam.com/video/QAGTXo70MmU/v-deo.html
Thank you for sharing this good video^^ 👍
How easy would it be to add a gyro like your other videos ? This is OK for drifting with different wheels
It's easy if you have upgraded the electronics otherwise it will involve some soldering on very small wires. It's still not that difficult though.
@@BeaversHobby I would love a gyro installing. I am not very good with soldering however. I was going to ask if I send you my car can you install it I pay you cash??
@@mikes0121 Unfortunately I can't do that.
@@BeaversHobby :( ok bro
Useful information. Great Job! Blessings.
Is there a way to reverse the throttle? Mine came new with the throttle control backwards. Everything looks to be installed correctly. Thank you for your videos. They are very helpful
Check where the problem is first.
If you can pull the trigger, push it to go one way then come back to centre again and push to go the other way then the problem is at the motor wire. You can swap the polarity easily by using a tweezer to push the tap on the motor plug down and pull the wires out then you can swap them. If you pull the motor plug out you'll se one side with the lock and the other side with the exposed terminal. Do it on the side of the terminal. It doesn't have to be a tweezer, anything thing enough can push that terminal down and you can pull the wire out.
If the problem is not at the motor wire, the wiring inside the transmitter is reversed. You will have to swap 2 of the 3 wires in the throttle potentiometer. Not sire which one so you will have to experiment which of the 2 wires give you reverse throttle.
Did pretty much the same upgrades. And yes, I agree that the motor pinion is bad... probably even the worst as that is not as easy to replace.
We can use 18650 for battery isn't it?
No, it's too big.
@@BeaversHobby Only if you want to use on the original place. I think we can mod. Or not?
@@kaiotech5902 Yes, you can file or mill the original gears down to something like 2mm peck and use the motor gear from Tamiya Mini 4WD (or a plastic 8T gear) over it then glue it in. I did that and it lasted much, much longer than the original plastic gear.
can it reverse
Yes, it can.
👍😎 we have 1 too. nice truck
That diffuser is just for looks.
ok buddy you finally earned my sub. love your k989 vids
Do you know if the new transmitter will work with the k989 receiver/esc combo? Would love to be able to dial the power down!
Unfortunately no, it won't work with the old combo.
Just bought one of these bad boys. Waiting for it to arrive.
I want to upgrade the diffs, front to a one way and rear to a fixed. Mini z ones or copies.
And I right in thinking I only need the longer front drive shafts and I can use standards in the rear?
If so is the an up to date list of where I can get the parts in the UK.
Is there a steering angle mod you can do?
I like the look of the carbon chassis and upper deck are they a direct replacement?? Seen some carbon shock towers to?
Thanks 🙏🏾
The one way I got from Aliexpress is really good. However if you don't want to wait a very long time then get a genuine Mini-Z parts within the UK.
And yes, you'll need long drive shafts for the front with one way. Both can be found in the UK from www.rcm8.net/ .
At the back you don't have to get a solid axle, you can just lock (glue) the original axle and it'll work. You don't have to change the rear swing shafts either.
The steering mod: follow this tutorial from 5:38 ua-cam.com/video/zB3pUN9XiSw/v-deo.html .
Caron chassis is not recommended. It'll mess up your ride height. However feel free to try.
Carbon shock towers are good. It should be in aliexpress so I don't know if there's any UK stock.
Great video, I got myself one of these as well!
How did you remove the pinion gear in the end?
I can't pull it off for the life of me and I wonder whether there's an easy way to do it.
There's no easy way to remove it except using a gear puller.
@@BeaversHobby Thanks, I really appreciate your reply.
@@klas7927 My pleasure.
where does one get center shaft pinions and diffs parts for these ? say someone would break those weaker parts u were talking about ?
It's on banggood and aliexpress. Banggood seems to be out of stock right now so here's the Aliexpress link. www.aliexpress.com/item/1005003674363056.html
I recommend using Mini-Z AWD differential in conjunction with the long CVD www.aliexpress.com/item/1005003399026933.html for better durability and fitting. Also with the long CVD you can use any Mini-Z AWD compatible diffs like ball diffs from GL Racing GLA and get the best performance out of it.
Can you recommend a good brushed ESC for this car? I installed one today and it lasted 1 battery before burning out.
Hobbywing Quicrun 1625 should fit the tall bit of the cockpit nicely. You'll have to change the transmitter too following this guide ua-cam.com/video/BSt7U-yOa4Q/v-deo.html .
Still, have you fixed the drivetrain before running, it's so sticky that it might burn the electronics out.
My K989 from 6 months ago also has a metal pinion and I've not succeeded on removing it.
You'll need a gear puller to do it.
Good video! I'm about to purchase two of the WLToys version so I can force people to race me. Am I correct in understanding that I can swap a car body onto the truck version? I was going to buy one car and one truck just for the difference, but it seems the truck has better upgrades already and I'd hate to buy something not as good over a body.
Yes, you can. The body posts are different length but you can swap those as well so there's nothing to worry about.
I have one and yes the drivetrain is very sticky!! I might swap them with Mini-Z diffs. Very informative video!
That'll do. I'll test later which CVD you need. The 10.5mm for Mini-Z wide chassis might be too short for Mini-Z diff. Usually I use the long CVD bit.ly/3m1i4bd with Mini-Z ball diffs.
Could the stick drive train be the reason my car stops responding to accelerator and only leaves me with steering control and no forward or backward movement after a short drive? Is someone freezing/locking.
@@shrimperlincs3395 Do you hear anything when pulling the throttle, like a beeping noise or the motor is trying to spin? You can also try and move the wheels by hand and see if the wheels can spin. If the wheels can spin alright, it's the electronics. If the wheels are too tight to spin, it's the drivetrain.
Hi there. I guess u get a lot of this questions. What car would u recommend? Affordable/ but able to achieve a lot with simple modifications?
WLtoys K989 series or this 284131. It'll need a some fixes but it's the best for the money.
Great video man, ur content is always informational
I just ordered one, thank you for the coupon ☺️
Dangit i just bought a 969 too. Oh well haha. Im following your modification series 😁
Today i ordered also but older with fiesta body.... Also i think if i calculate this good u can get sub 20$ with code on 11/11 promo
Hello Beaver, great review. I am fan of your RC car videos they are so amazing and easy to understand. I am beginner and want to start this hobby, Can you please create a drift car build series with this car. Also if possible share parts from either aliexpress/bangood.
It is exactly the same car as K989/K969 so the most updated version of the drift build is still this video. ua-cam.com/video/j9pO35iaqfo/v-deo.html
is there any transmitter that support with the new controller? if exist, where can i buy it?
You can mod a transmitter that has PPM output with multiprotocol and use XK X420 protocol.
If you want a ready made one I'm afraid there is no pistol grip or car transmitter, only air transmitter like this bit.ly/3BN6Qik .
I also have a series showing how to configure it to use with cars.
ep1 Unboxing, basic setup ua-cam.com/video/vSRR67jMhzI/v-deo.html
ep2 Self-centering stick ua-cam.com/video/wKuwODFd338/v-deo.html
The Transmitter Looks Like a cheapo Version of the sanwa mt4😅
It is indeed!
Please do a drift setup on this brother. Would be great. Thanks.
Here it is. ua-cam.com/video/j9pO35iaqfo/v-deo.html
Yes, it's the same car with a different body.
Ok Uncle Wodger
Hi man.
How reliable is the spider gears and the gears in general?
It's not reliable even in this new version. It'll need some fixing to work and will still wear out quickly. I ended up replacing the diffs with Mini-Z diffs.
@@BeaversHobby thanks. Does the mini Q diffs that you have linked work just as well?
@@philipbrits2984 Yes, those are what I use. You'll also need the long CVD for it to work because this is a wide chassis and on stock setup they just extend the outdrive instead of making longer CVD shaft. By the way I just checked and Mini-Q diff is out of stock right now. You can get this instead. It'll be all metal diff. www.banggood.com/custlink/KGmCaD6y0r
@@BeaversHobby thanks. If i get that metal diff you linked, do I still need the longer cvd's?
@@philipbrits2984 Yes, you still need the long CVD.
Hi Beaver thanks a lot for your fantastic channel and all the information you share with the public. I want to get my fist 1/28 car. I have a lot of experience and know RCs very well, just never tried anything this small. I want to put together some kind of rally car, possibly a kit, certainly with custom electronics, something that can cope with dust and can be used outside. Any advice? Also I need advice about ESC and brushless combo, something on banggood? And TX and RX what is the best micro receiver and what TX will it use? Tnx
For using outside your best bet is Wltoys K989 or 284131. Unfortunately they don't sell this car as kit so you'll have to work it from RTR. Any transmitter will work providing you have a small enough receiver to fit inside. The antenna-less receivers from Sanwa or Flysky Noble (FGr4S) will do nicely especially the Noble because it's dust proof. If you want a small receiver then you'll need Futaba with S-FHSS/T-FHSS, Sanwa with FH3/FH3 or Flysky Noble. These transmitters have receiver (or compatible receiver in case of Futaba and Sanwa) with JST-ZH plug so you can use Atomic or GL brushless ESC directly without plug conversation. As for the motor, take a look at BYRC on AliExpress as they have enclosed brushless so you can run outside safely.
@@BeaversHobby Hi thank you so much for your answer I really appreciate your help. Today I bought the 284131, although I don't like the body. But the car will slowly be upgraded. For now I want to see test drive the car etc, but I the NB4 seems a solid choice for less money. What do you think about Furitek brushless combo? I watch your review and to me they seem pretty good as a company. Also have you ever heard of Carisma GT 1/24 series? The GT24B (kit version) would be my first choice to drive outside but due to Covid regulations etc they will not ship to Europe.
@@flyingformation1878 From what I know Carisma GT24 series is really good. There are RTR around in Europe but as you checked, the kit won't ship to us so that's a big disappointment. Anyway, best of luck with the project!
@@flyingformation1878 The Furitek is very good good but I think it's too expensive to get for only 1 car because of the bluetooth module. If you have many cars then it's more economical because you can share that module.
@@BeaversHobby Tnx again for your help. I checked the BYRC and it seems a very good deal (Combo + Pcard for 29$) it's great to me. For now I will stick to standard electronics and 1 car because I need to see how good they are to begin with etc but I want two or three cars (drifting - touring - and my off road project with the Carisma). I hope you don't mind if I ask some other questions in the future! Thanks mate.
Is it worth buying this and upgrading it besides the k969
This is a better car just because the transmitter is better. If you can verify that the K969 that you are getting is the new batch with the same transmitter then get the K969.
I have new k969 that arrived last week everything is the same like metal ball head, metal pinion, battery connector etc. The only diff is the controller which is the old big red one. Quick question can i buy the new controller and will it work with my k969? How will i know which protocol and the esc?
The big red controller is the V2x2 protocol. You can get the WLtoys P33 transmitter for an upgrade.
@@BeaversHobby right! Thanks
are u gonna do an upgrade series on this one like u did for the k989?
It's the same car so I'm not going to repeat all the fixes and basics but go straight to budget touring car 2022 edition.
Great review. Does the car come with full bearings from the box?
Yes, it has full bearings out of the box.