I want to say thank Dave for the insight to resolving my valve issue. This was an new zoned I added with a new valve and solenoid. After checking the voltage and ohms, afterward I applied a paper clip and repeating up and down motions for 15 seconds, replace solenoid, turn on the valve wow it worked.
My valve will only open if I open the bleed switch a little, while the solenoid is engaged. If I shut the bleeding while the solenoid is engaged, the valve stays shut. I guess the cause of this problem is the leakage from the bottom chamber is too strong into the upper chamber. But how? leaking diaphragm? How else? Please advise. Thank you so much.
Hello Sir One of my valve on my sprinkler is not working with controller. It’s working manually when I do a quarter turn. I changed both the diaphragm and the solenoid and still have the same issue. I checked the ohms and it’s all in the correct reading . Do you know what will be my issue? Thank you!
Hi, Bron! It is most likely not the valve, it's probably electrical and could be the controller not putting out power, a wiring problem between the controller and valve, or the solenoid on the valve. The valve itself is usually fine. If you need help - we recommend contacting a certified irrigation contractor in your area to help! Hope that helps! Thanks! Automatic Supply
My Rainbird valve quit opening. If I turn the solenoid it lets water through. So I replaced the solenoid and this did not fix the problem. I checked power and have power to the solenoid. To make it work I still have to turn or loosen the solenoid. What is the problem?
Hi, DIY Oregon - Thanks for the comment! It could be several issues that you're running into. Even though you're getting power to the solenoid, it might not be enough power. This would be the ohms test that Dave is referring to in the video. We have seen a valve get power before, but not have enough amps to make the solenoid work properly because the wire was damaged and losing voltage. Another issue would be whether the valve is porting properly. Once the solenoid opens, it has to port water from the solenoid chamber to the downstream side of the valve. If that gets clogged a valve will not open. Hope that helps!
With all due respect, you keep following possible electrical issues when you already established with the manual bleed screw that the valve won't open. You could have done that in the first 10 seconds.
He's just nervous being on camera. I do the same thing. I think he's done a wonderful job of explaining, and I love that he's not super obnoxious like a lot of UA-camrs!
I had a hunter SRC plus Seeing on the contral screen are Err . I Am turn on manual all station working ok. Do You known what Err meaning, and how to fix it.
Hi, Juliana! If it the "ERR" is the only response shown, it is electrical interference at the remote plug-in area. Make sure it is covered and doesn't have bare wires around it. If the ERR message is showing with a station number the problem would be found in the wires leaving the clock and going to that valve for that station. A short in the wires or a bad connection can cause ERR and still work. One option would be to take the battery out and unplug it. Wait ten minutes then try again. If it is still not working, we would recommend calling Hunter Industries tech support at 1-800-733-2823. Hope this helps!
Give him a break, he's just nervous being on camera. I love his delivery! He reminds me of a friendly hardware store owner in some small town, calmly and patiently explaining how things work.
I want to say thank Dave for the insight to resolving my valve issue. This was an new zoned I added with a new valve and solenoid. After checking the voltage and ohms, afterward I applied a paper clip and repeating up and down motions for 15 seconds, replace solenoid, turn on the valve wow it worked.
Thank you so much for explaining, I'll try your tips for my valve not opening.
Thank you, fixed my valve with a paper clip!
My valve will only open if I open the bleed switch a little, while the solenoid is engaged. If I shut the bleeding while the solenoid is engaged, the valve stays shut. I guess the cause of this problem is the leakage from the bottom chamber is too strong into the upper chamber. But how? leaking diaphragm? How else? Please advise. Thank you so much.
My Rainbird valve doesn’t turn on manually turning the solenoid, the sprinklers don’t pop up, just low flow. What should I do? Thanks in advance
Hello Sir
One of my valve on my sprinkler is not working with controller. It’s working manually when I do a quarter turn. I changed both the diaphragm and the solenoid and still have the same issue. I checked the ohms and it’s all in the correct reading . Do you know what will be my issue?
Thank you!
Mine turns on manually but not with the timer. Should I just replace the valve?
Hi, Bron!
It is most likely not the valve, it's probably electrical and could be the controller not putting out power, a wiring problem between the controller and valve, or the solenoid on the valve. The valve itself is usually fine. If you need help - we recommend contacting a certified irrigation contractor in your area to help! Hope that helps!
Thanks!
Automatic Supply
My Rainbird valve quit opening. If I turn the solenoid it lets water through. So I replaced the solenoid and this did not fix the problem. I checked power and have power to the solenoid. To make it work I still have to turn or loosen the solenoid. What is the problem?
Hi, DIY Oregon -
Thanks for the comment! It could be several issues that you're running into. Even though you're getting power to the solenoid, it might not be enough power. This would be the ohms test that Dave is referring to in the video. We have seen a valve get power before, but not have enough amps to make the solenoid work properly because the wire was damaged and losing voltage. Another issue would be whether the valve is porting properly. Once the solenoid opens, it has to port water from the solenoid chamber to the downstream side of the valve. If that gets clogged a valve will not open.
Hope that helps!
@@AutomaticSupply Thanks, I bought a new transformer/adapter at Home Depot for $14. Fixed the problem and it works fine now.
Yeah change the diaphragm clean the unit
@@fergferguson7370 LOL this was like over a year ago.
With all due respect, you keep following possible electrical issues when you already established with the manual
bleed screw that the valve won't open. You could have done that in the first 10 seconds.
Informative video, but this guy sounds like he's about to cry..
hooknbook911 lmaooo he really does
Guys hands are Shakey I think he has some sort of issue where his he's just Shakey. Voice box to hands
He's just nervous being on camera. I do the same thing. I think he's done a wonderful job of explaining, and I love that he's not super obnoxious like a lot of UA-camrs!
I had a hunter SRC plus Seeing on the contral screen are Err . I Am turn on manual all station working ok. Do You known what Err meaning, and how to fix it.
Hi, Juliana! If it the "ERR" is the only response shown, it is electrical interference at the remote plug-in area. Make sure it is covered and doesn't have bare wires around it. If the ERR message is showing with a station number the problem would be found in the wires leaving the clock and going to that valve for that station. A short in the wires or a bad connection can cause ERR and still work.
One option would be to take the battery out and unplug it. Wait ten minutes then try again. If it is still not working, we would recommend calling Hunter Industries tech support at 1-800-733-2823. Hope this helps!
Mr. Personality. video needs to zoom in on valve more.
Give him a break, he's just nervous being on camera. I love his delivery! He reminds me of a friendly hardware store owner in some small town, calmly and patiently explaining how things work.