My Homemade Metal Lathe Part 3

Welcome to INNOVATION TIME.💐
Hello friends
This is a semi-automatic lathe that X axis has a motor with adjustable speed. In the future will added an electromotor to Y axis and will be completely automatic. The movement of the device can controlled by using a joystick. The main electromotor that rotates the chuck is speed adjustable. This lathe machine is not for sale. I spent about a year to make this lathe and I tried to show you that it is possible to make this tool with minimal facilities. I used scrap metal as much as possible to make this lathe and finally spent about 1500 dollars. This work has been prepared and published in several parts. This video is one of them. To financially support this channel, you can use Super thanks and pay membership. Your support is my encouragement.
Please don't forget to subscribe 👆
yun.ir/1v78ad
Top On Sale Product Recommendations!
CNTD Joystick Switch C2MN-T4 2A2B Monolever Switch Four Directional Reset 2NO 2NC
Click & Buy: s.click.aliexp...
5.5KW 380V 3 Phase 7.5HP Vector Control VFD Variable Frequency Drive Converter Variator for Motor Speed Controller Inverter
Click & Buy: s.click.aliexp...
VEVOR Metal Mini Lathe Mini Metal Lathe Variable Speed Precision 1100W Machine Small Mechanical Lathe Machine
Click and Buy: s.click.aliexp...
Playlist:
• my homemade Lathe machine
• Bearing puller
• DIY
If this video helped you out share it with your friends 👉
Part 1: • My Homemade Metal Lath...
Part 2 : • My Homemade Metal Lath...
Part 3 : • My Homemade Metal Lath...

[@innovationtime20]

Top On Sale Product Recommendations!
VEVOR Metal Mini Lathe Mini Metal Lathe Variable Speed Precision 1100W Machine Small Mechanical Lathe Machine
Click and Buy: s.click.aliexpress.com/e/_ok2QzJk

[@jamesmiller800]

I would like to see the finish cleaner like grinding the welds smooth and the turned finish on the controls smother but over all its a good job.

[@innovationtime20]

💐❤️

[@martinheralt4240]

I dont want to nitpick ,but if you want to use it for longer time then you should ad adjustable gibs to cross slides , those gibs are used to set tolerances . As is now it will wear out and it will not hold any tolerances properly and if that happens you can propably use it only as wood lathe ... On other note I like how beafy it is build and that you used conical bearings for spindle ,but please use oil for sliding surfaces eather way oil or machine oil, just some kind that doesnt make it sticky after some time ,if you aply right oil it will move smoother and wear less

[@innovationtime20]

Hello, dear Martin
You're absolutely right, I'll probably add this in the future so I don't run into trouble. thank you so much 🙏

[@TheVersatileMindMedia]

Totally impressed with your skills and the learning curve is all the challenge you need, awesome! I like all things DIY, this is what I need to make, thanks for the inspiration!

[@innovationtime20]

❤️❤️

[@nargessayah4186]

Although i have no clue of what you do, it is satisfying to watch

[@AutodidactEngineer]

Some things are best left to professionals and this ain't them.

[@jesusfajardo2778]

La placa sin duda te la mereces 💯 Buenos videos 👍

[@innovationtime20]

Thanks bro 👍

[@kidbolas4007]

CONGRATULATIONS ! You are a genious.

[@innovationtime20]

Thanks 👍❤️

[@Hassen78]

very amizing thank you very much for this video😍🤩

[@innovationtime20]

🙏🙏

[@aymanayman7963]

Very nice work

[@innovationtime20]

Thanks 👍

[@joseneriacoemel9825]

Laik garantido my friend tj Brasil

[@123suzukisamurai]

Very innovative. Well done

[@innovationtime20]

❤️

[@gmendes1831]

Great job!

[@innovationtime20]

Thanks!

[@NorBenz-fz3sn]

شكرا لك... عمل راءع....حياك الله و رعاك.

[@innovationtime20]

Thanks 👍

[@hampopper3150]

You need a give strip and screws in the cross slide.

[@innovationtime20]

👍

[@vahidtaherkhani921]

Very nice tankhyou

[@innovationtime20]

Thanks 👍

[@jeffreyboatright6919]

Very impressive

[@innovationtime20]

❤️

[@ivairivair6756]

Boa tarde meu amigo tudo bem? Sou aqui do Brasil gostei muito do seu trabalho e o torno que fez.Pderia você me passar uma lista de material que usou pra fazer o torno completo? Te agradeço Deus te abençoe sempre.

[@innovationtime20]

Hello my friend
Thank you so much 🙏
I will write a list in video description 😉

[@FranciscoJerez-uz1vb]

Buenas noches el precio de el torno gracias le saludo de Guatemala

[@innovationtime20]

Hello my friend
It is not for selling but the link another kind lathe for selling is in description 💐

[@atenayousefi9503]

سلام من مهدی هستم از ایران درود بر شما بسیار عالی بود فقط اگر امکان داره درباره سیستم رزوه توضیح بدید با تشکر

[@innovationtime20]

سلام مهدی جان
ممنونم
خیلی ساده ، دوتا موتور(یکی برای سه نظام، یکی برای محور طولی) که هر کدوم یک درایو دارن. حالا اگه هر دو درایو از یکجا فرمان چپگرد و راستگرد بگیرن میشه هر رزوه ای رو زد، فقط کافیه سرعت ها رو تغییر بدید تا گام رزوه عوض بشه 😉

[@sultanshaikh2839]

Pliese making blok honing machine

[@fausmartinez6342]

Que número de balero conico es

[@innovationtime20]

The shaft was 70 mm and inside size must be 70 mm and outside is 125 mm

[@mostafamohammadrezaee-ve4ro]

سلام، عالیی، موتور اصلی چند وات هست؟ چند دور هست؟

[@innovationtime20]

سلام
ممنونم
موتوری که استفاده کردم، 2 کیلووات 3000 دور هست، که بهتر بود 2 کیلووات 1500 دور استفاده میکردم.

[@mostafamohammadrezaee-ve4ro]

@@innovationtime20 من دارم یه مینی تراش میسازم، به نظر شما نیم اسب جواب میده؟ تو یوتیوب چندتا کلیپ دیدم که نیم استفاده کردن، ولی مطمئن نیستم

[@innovationtime20]

بستگی داره چی باهاش بتراشی و چقدر بار بدی،
به نظر من هم نیم اسب کمه
دور رو با چی میخوای کم و زیاد کنی ؟

[@mostafamohammadrezaee-ve4ro]

@@innovationtime20 بیشتر میخوام آهن بتراشم، البته شاید روزی یک ساعت،
دور با پولی کم و زیاد میکنم مثل دریل ستونی
خیلی برام مهمه که دستگاه جمع جور باشه چون تو خونه دارم کار میکنم
بار زیاد نمیدم چون زمان برام مهم نیست، فقط میترسم دستگاه وسط کار یه دفعه استپ کنه،
موتور هم میخوام یه موتور تکفاز تک خازن ۱۵۰۰ دور نیم اسب یا نهایتا ۱ اسب بزنم

[@innovationtime20]

خیلی هم عالی 👍
به نظرم یک اسب بزار بهتره

[@sidneimattos6116]

Olá vc tem pra vender

[@innovationtime20]

Unfortunately not ❤️

[@allymariachi9230]

Hellow friend. Thus is a very nice lathe
Especially how you made it and got it to make threads by using VFD,it is the first time I've seen that.can you please show us maybe in a video how you wired those two VFDs together in one joystick to make them able to cut the thread.i would love to try and make one myself if you dont mind

[@innovationtime20]

Hello my friend
Thanks for your kindness
Two motors and two inverters, the question here is how to use left-handed and right-handed at the same time
It is enough to control both inverters from the same place, but the problem is that it is not possible to connect both inverters to one joystick. It is enough to put an Electrical Relay for each of the inverters. In this way, both relays can be connected to a joystick.
The electrical circuits of the relays are usually drawn on them

[@user-cyka]

Почему поменял подшипники на конические?

[@christianmusso629]

He showed why. He was having too much play at the mandrel!

[@user-cyka]

​@@christianmusso629подшипники можно было взять по типу UCF 208 например

[@MaksimoV35]

халтура

[@phuochungnguyen4221]

Làm thế nào mà dùng biến tần bạn có thể tiện răng theo như ý mình vậy. Nó rất tuyệt vời. Mong bạn chia sẻ về điều đó

[@innovationtime20]

Both inverters must receive commands from the same place and an encoder must be used so that the time delay does not occur😉

[@koyogalarga3587]

Un verdadero artesano, todo mi respeto para ti y tu equipo, ya que se requiere de muchísima paciencia, para hacer lo que haces, no cualquiera hace un torno de metal desde cero.
Muchas felicidades y mucho éxito
👏🏿👏🏿👏🏿👏🏿👏🏿👏🏿👏🏿

[@innovationtime20]

Thank you my friend 🙏💐💐🙏

[@fernandorosales2418]

I'm impressed that you built a working lathe with nothing more than an angle grinder, a drill, and a stick welder. The machine is a bit crude, but I'm impressed by how much you've been able to do with so little equipment.

[@innovationtime20]

Thank you dear Fernando 🙏💐

[@My_Gaming_Mind]

C'mon bro, didn't even bother to remove the rust or grind the welds a bit to make them look good before painting.

[@innovationtime20]

Thanks 👍

[@yehudaegert2276]

Awesome build bro. But this video felt rushed and missing large amounts (especially the first 5 minutes, they could've been their own video). Unlike the first 2 which were awesome.

[@innovationtime20]

Thank you my friend ❤️❤️

[@reyn_mechanic896]

What's the name of the device you use for speed control??

[@innovationtime20]

Hi
The name is Drive or Inverter

[@haroldpatino9811]

Parcerito excelente video, pero tengo una duda, ese controlador sirve para hacer todo tipo de rosca o es sólo para velocidad. Y como haces la rosca agradezco tu respuesta saludos desde colombia

[@innovationtime20]

Thanks 👍
I can control the speeds and the ratio between speed's. It mean I can make any thread 😉
I don't understand the second question

Muito bom . Parabéns pelo belo serviço 👏👏

[@innovationtime20]

Thanks 👍

[@mezanijan894]

thanks

[@mempadunex9693]

Your project is awesome.. High level work. 🎉

[@innovationtime20]

Thanks a lot 😊

[@miladgorogchi1416]

سلام حاجی دمت گرم ویدیو عالی بود ولی ای کاش آون گیره ش رو هم دست ساز میساختی 👏👏👏

[@innovationtime20]

سلام، مرسی
داداش منظورت قلم گیره؟
اونو هم دستی ساختم توی ویدیو پارت ۲ هست.😉

[@miladgorogchi1416]

@@innovationtime20 شرمنده منظورم سه نظام بود

[@innovationtime20]

👍
اون کار سختیه ، فرز میخواد که من ندارم 😉

[@chettia100]

thank u man ..u is a steel boss

[@innovationtime20]

Thanks 🙏

[@clip88th33]

Xin công thức tính tốc độ để tiện các loại ren

[@innovationtime20]

👍 sure

[@didinsuharto7058]

Good job bro👍👌

[@innovationtime20]

Thanks ✌️

[@yehudaegert2276]

Can make a build sheet and sell it?

[@innovationtime20]

🤔

[@Gokce_Seramik_Bileme_Taslari]

Hii kw motor ?

[@innovationtime20]

2.5 kw

[@mohdmuhaimin8793]

Diagram electrical please

[@wedhuz78]

At least clean or grind all the steel plates from the rust or debris before using them. Use oil to smooth the bed ways and all those steel plates that rubbing each other. i can hear squeaky sound while these plates are moving. These steel materials used in this video are not cheap at my place 😢😢😢
However, still a nice DIY lathe ✌✌👍👍

[@innovationtime20]

Thanks 👍

[@eduanlorenzosanchezmendoza9685]

Soy de Peru, donde puedo adquirir un torno asi, y cuanto me cuesta

[@innovationtime20]

Hi
I don't know my friend
But I show tou how you can make it 👍
I spent about 1500 dollar for it

[@michaelsimpson9779]

Ignore the haters, you've done well.

[@innovationtime20]

Thanks 🙏💐

[@95machine29]

Sir, can explain for me: you used same joystick switch for spindle and X axis when threading? Can make other videos preparing for threading, I see you make 2 pitch like how ratio of pulley spindle, ratio of gearmotor X axis; how rpm of spindle, rpm of X axis; how pitch of lead screw,... ?

[@innovationtime20]

Hello my friend
I used two inverters, one for the x-axis and one for the Chuck, both of them can be controlled by a joystick. When the fixed chuck motor speed , any pitch can be created by changing the X-axis motor speed, and I found different pitches by trial and error. 😉

[@innovationtime20]

Of course, it is better to use an encoder so that no errors are made

[@95machine29]

good explain but can share me deep information for what device use with encoder for control pitch, on VFD not port for encoder or how use encoder, any...@@innovationtime20

[@SergeiPetrov]

Про резьбу без энкодера просто звиздежь.

[@innovationtime20]

Thanks 👍

[@محمدابوصلال111]

ما شاء الله كنت عن حسن ضني الان تعمل جيدا

[@innovationtime20]

🙏❤️

[@silvanpassos7663]

Parabéns ficou top 👏

[@innovationtime20]

❤️❤️