How Do You Determine Port Area When Designing Enclosures? | Car Audio Q & A
Вставка
- Опубліковано 24 лют 2015
- Watch Allyn explain how to determine port area amount when designing enclosures, with Term Pro software. He takes us step by step on determining port area when designing ported sub enclosures.
Shop Subwoofer on our Site: bit.ly/1DlwE2c
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Sonic Electronix always strives to be the premiere online shopping destination for car electronics and other consumer electronics. Our slogan is "The X-Factor When Shopping for Electronics" and it is our goal to be just that. We're here to help you find solutions and great prices without sacrificing service.
Our Store:
www.sonicelectronix.com/
Our Facebook:
/ sonicelectronix
Our Twitter:
/ sonicelectronix
Our Instagram:
/ sonicelectronix - Авто та транспорт
Ok..... how would you figure that without the termpro?
WHERE THAT TERMPRO TORRENT AT HOME BOY!?
Right? still nowhere
ALLEN!!!!!!!!A when and why to use a relay would be a GREAT contribution to the community! Show how to wire them, why they are used, and a few beneficial uses...that will definitely pull some views!
Your video helped a lot thank you
I could have sworn I typed per cubic foot. Thanks for answering my question! I really appreciate it.
The more i learn about this program, the more i want it
Its in a place where you break your piggy bank. It's $250 if you want it.
I want it too. but is is very expensive
If you triple the power that u put into the sub. Would u need to modify the enclosure design?
That's a good information. But not every one have term-lab.
Term pro* neither do I. I would like to have it.
Does term pro (latest version) support slot ports where it will shape them inside the box (fold them as necessary) to fit it.. and provide the cut sheet for that design? Or is it up to you to figure out how to fit a longer port inside a box?
Hey man, what's the best type of Port? Thank you.
If I have a measure for a bandpass box with cilindric port, can I use the port volume and make the port rectangular?
Alright i understand that it doesn't seem like he answered the question but if you look closely the term pro software shows 21 sq inches of port area which is still alright the rule of thumb for port area is 12.5 - 16 sq inches of port area per cubic ft. of the box so for example the box design that Allyn made is a 1.5 cubic ft. box so if you do 12.5 sq inch x 1.5 it would be 18.5 sq inches of port area and if you take 16 sq inch x 1.5 you get 24 sq inches of port area their are a lot of factors that come to play also such as how much power will you be running to the sub. other than that 21 sq inches of port area is alright smaller the port area the bigger chance you will hear chuffing... if you take the ports internal height and width which was 10.5inches x 2 inches your get 21 sq inches of port area... also it is not a scam having term pro is a good investment if you design sub or speaker boxes alot then again you dont really need it their are free programs such as WinISD for me i have Term pro, winISD, torres, and bass box pro so yes i check my design multiple times and also check it on paper with alot of math lol ... also there are some that go way more than 16 sq inch per cubic ft. but that is more for advanced builders lol hope this helps clarify that allyn isnt wrong and answers that question lol also dont forget that the port also has a displacement and slots take up more space than aero ports
I’ve got my outer dimensions for my box and know how to tune the box but what should I tune my box to? I’ve got 2 RE SE15 D4’s running off a CT sounds AT1400.1 in an old suburban. Now I’ve got them in a probox and it is way too small and only hits about 42 hz with hardly any power. I know a bigger and lower tuned box will help out a lot. I’ve got designs drawn for a 34hz box but would it be ok to change up my port for somewhere more like 27hz? Thanks for any help
The Bangin' Burb I would not tune lower than 30Hz unless you want to play 20-45 Hz and be extremely peaky. Tune to 32 or 34 Hz is my recommendation. 4” - 6 “ aero port would be easy to adjust for different tunings ( depending on how you build it )
how would you use termpro to make a truck blow thu?
Lol, better explanation then the actual term pro dude.
Aside from the port size, what other factors affect the velocity of the port? Would box size or narrowness?
How do you figure port velocity without TermPro?
Buy it, obviou$$$ly
Man I'm in a dilemma I dont have term pro and I'm in the final stage of my enclosure I just need port dimensions if you are available atm real quick I can email what I have and pix if you can manage a quick port design with what I got. Thank u
Okay. So when designing a ported enclosure, the recommended volume of a subwoofer does not include port area in the recommended enclosure design? Such as a sundown SA15 requires 4 ft^3 ported. So what that's telling me is a 4 ft^3 box plus the port. Is this correct? Or does that mean total volume including the port?
Adam Moore correct, the port area and volume do not count in the 4ft^3 that is net not gross. The port area would need to be added to the 4ft^3 ..
Which software are you using
Question... how to make a imported bass box for a 09 acura tl
Can u make a video for rexxx18d4
I have an 02 mazda protege5 and I'm wanting to install 2 8 in sundown subwoofer. I want to have each sub running off its own amp. How would I wire it all together?
two separate chambers within the box, wire each sub to its own amp.
That's easy ok cool thx
I need a design 4 yalls gothic gw3 12 on a planet audio 2.5k torque I need a ported box design
What app are you using?
Whaaaaaaaaaaaaaaaat?.....glad i dont need a computer to do the work for me....paper and pencil works fine
You did not answer the actual question whatsoever...You used your software, and told us "you wanna have less than 10% port air velocity; The port area doesn't really matter, we need to manipulate it"...which you relied on your expensive software to explain it to us. So thank you for literally telling us nothing, and maybe conning a few people into buying a 250$ program to build a 50$ box.
WinISD is free and it also gives you port velocity. Put in your box volume, tuning frequency, & port area and it'll give you air velocity
Psst the port volume is also wrong. That was the total volume from the outside of all four walls in that software of the port, when determining the volume of the parts added by the port you measure the length of wood added to the structure. In a slot Port using the entire height of the box and starting on the edge, you only need to know the length of one side, do the math to calculate that it's actually a port volume of roughly 0.13 cuft. Not 0.7. I would not buy boxes from them. If the box was bigger, and this size port was built in full with all the sides separate from the walls including top and bottom, that would be the actual port volume.
I agree. I was expecting math.
@@mattwells1036 he didnt do any of it correctly. Port area is determined from the type of enclosure and the size of the chamber. A 4th order bass reflex box or ported box usually has 16 sq inches per cube of cone area. If you have a 4 cube box that 4*16=54. If your internal height is 11.5 then do the math for the width, enter that into winisd and it will give you your port length. If you were building a 4th order bandpass box the cone are is going to be different. Usually higher like 20-24 sq inches of cone area. Also the port tune is going to be higher like 40-60 hz bc it acts like a limiter on those boxes.
This guy never touched that most important rule so dont buy boxes from them. Ive seen other videos of his and they lack the real details as well.
The x16 rule dose not work with all brands....cone areas differ brand to brand....so does port area...in the same cubic footage nonetheless....ur x16 rule wont work with say some sundown skar and audiopipe brands...all in all ask manufacturer for port area specs...most are usually between a x11 to a x17 rule
Can anyone recommend what port area and length for a 3.75 cubic foot box running 2 12s
Port area should be between 21.70-41.85 per 12 and port length depends on how high or low you wish to tune the box...
In your design, you actually did 14 square inches per cubic foot of port (21 square inches ÷ 1.5 cubic feet). This is within the 12 to 16 square inches per cubic foot rule. 😊
port noise is relative
Non if in Sedan
You can hear it in Hatchback type
Should the area of the port and port material be subtracted from the total enclosure area when calculating the enclosure size? Thanks
Yes.
Not the area inside the port. The area the port walls are displacing is all that you need to calculate and remove. The area inside the port is still part of the enclosure displacement.. their port displacement was way off as that was including all 4 walls of that port dimension. In the video he said and showed 0.7 when it was really only roughly 0.13.
🔴 so dont focus on 12 to 16 square inches of port area per cubic foot, instead focus on air velocity?
The port area must be between a 30% or 40% of the cone area. That is a good port size whit no port noise and great sound
Is this for any port?
@@James10864 Port noise occurs when the speed of the air passing through the port exceeds 17 m/s. The size of the port depends on many things: size of the subwoofer, the size of the box and the intonation of the box. Knowing that, the size of the port has to be enough so that the air speed is equal to or less than that mentioned.
Hello, where can I buy and download software, thank you?
代聪 only that will no one will tell you here 😂
Sorta helpful if you have the computer program to do the math for you.
How would you measure the Cone area of a square subwoofer. You wouldn’t use Pi because it’s not round correct?!
winisd....its free and its dead on once you learn how to use it
Is it safe to say your port volume is about 25% of the total volume
No.
No. And the port volume calculations in this video were incorrect. Those in the video used all four sides of the port as the port volume. But the design uses the top bottom, and outside walls as three of the ports sides. The volume being removed from the internal displacement is only that of the one side, which gets shorter compared to the port length when making an inside turn, as well as the opposite for an outside turn. Their incorrect calculation stated the port displacement of the final design was 0.7 cuft, but the it'd be roughly 0.13cuft. the prior ones were also wrong
Approximately 12.5 inches port area per cubic foot of box is the best compromise for box size and performance. I own a sound system company and have been experimenting with building my custom powered speakers for portability reasons.
Yooo I need help
that's great and all but term-pro is $250 bucks...
you mean "free".
where is this "free" version of the software you speak of?
its not on any piracy sites there guy
BRBingeDrinker calm down fucker.
*****
er.. i'm calm. lol
LOL 3minutes in 1.76 cuft with sub disp and port is almost 6 cuft but tuned to 17Hz
Um, that is not the correct port volume. That is the port volume of all four walls of the port, in this design, the top bottom and outer side of the box act as three of those four walls. The actual cuft of the port for that design is roughly 0.13 not 0.7. that is what you need to add to the boxes cuft. And likewise that ridiculous 8+cuft total was wayy off man. Am i the first to notice this?
And of course port length isn't necessarily the actual length of your port wall. The middle is where you measure the port length, so the inside port piece might actually end up a tad shorter, and more so the more times it has an inside turn. This reduces the cuft it takes up. And on the contrary, when you reach a length that requires you to make another wall to continue the port your adding more cuft(obviously). Any outside turn pieces will use more length of wood than the port length it gets, and you can also use the other side of the existing port as the inside of this part of the port to not add more cuft to that.
Sorry, I'm not going to pay 250.00 for a software program to build one set of speakers.
Wow . Told nothing about port area. You need an average of 16 in of port area per a cuft of air space lol.
Basically he can't explain it