For those that live in humid environments... In addition to the really nice dryer used in the video, it's not a bad idea to have a water trap and filter at each air station. Another tip: When you start your main loop, run it right up snug against the ceiling, then slightly slant the pipe as you run it around the garage so that it is going just slightly downhill. In other words, you'll be moving the pipe down the wall slightly as you go. This makes sure that any remaining water will run down to the next water filter at your next air station. Another reason for wanting water traps/filters at each drop: The hot air will continue to cool and water will condense out of it even after it has gone through the large dryer shown in the video. That's the reason he needed to have 25 feet of hose before the dryer.... to allow the air to cool somewhat before reaching the dryer. The problem is the air will continue to cool down and shed moisture *after* it has left the initial drying canister. That's why you want to have a trap/filter right next to where you'll be plugging in your tool. Drying canisters/filters/traps can't remove *all* of the moisture in the air. They can only trap the moisture that the air is shedding as it cools down. The air will continue to cool off and shed water all the way to the tool you're using. So it's important to filter the water out as close to the air temperature that the tool is going to "see" as possible. One last tip: It's not a bad idea to use one of those cheap see-through water filters right at your tool connection. That way you'll see if you're in need of additional water trapping/filtering, and you have one last chance to dry the air before it enters the tool. You'll only rust out an expensive tool *once* before you learn the importance of *dry* air.
When I originally plumbed my compressor in my 1200 square foot shop I had drops all over the place. Now I have a 100 ft hose reel in the middle of the shop and eventually disconnected the rest because I never used them. The hose reel is so easy to keep the hose neat and out of the way.
Yeah those hose reels are great. I do have a specific time when I need air on the other side of my garage and am also working in the middle of the garage where the airline used to run across the floor. For my applications, this one particular drop makes a huge difference. 👍
Great system. We’ve used something similar in large dental offices. The only suggestion I would make is putting the oil/water separator before your dryer. That drying medium works great to get water out, but will fail prematurely due to the oil coming from your compressor. Thanks again for all your vids
Oh sweet! I never thought about that separator but that makes a lot of sense. Thank you for the tip. Glad you enjoy the videos and thank you for watching! Cheers👍
@@frostgfx most offices will use a dental or medical grade compressor. Some of these manufactures include Air Techniques, Midmark, Adec, Techwest, and so on. They use filters to reduce moisture and produce the cleanest air possible. Some offices use "off the shelf" compressors and they have to incorporate dryers and filters to remove moisture and produce clean air
Hahaha! I thought that too but was again, just way to curious. Not sure why I keep doing that but sadly it isn’t the first time I’ve done that as an adult. Hahaha. Thanks! I’m really enjoying them. 👍
I used to build houses and commercial projects. I had an old plumber who use to work in natural gas’s installations. He told me the trick and it has never failed me especially with gas and compressed air installations. He used to tell the people he oversaw, “DO IT ONCE AND DO IT RIGHT”! Best regards. Richard
I am a collision shop sales rep for my day job. Your garage’s air flow set up is now neater than most body shops 😂🤣, they just drag 100ft air hoses around.
Oh boy Jeremy. I laughed out loud so hard when I saw you stick you tounge to the aluminum. Great air system by the way haha. Shop improvements always feel so good eh?
I never want to see someone get hurt for the sake of a laugh... But... That made my morning. Hope your tongue is okay. It's also good to see that we all have our 'oops' moments. Stay safe my friend.
The system I went with suggested using teflon tape first then pipe dope on top of that when installing the fittings. Messy as all get out, but I didn't have one leak.
Interesting. I remember that when I worked at Sanjel (an oil company) we were not allowed to use both. Either one or the other. The bosses all preferred the pipe dope but it was a big no no to use both. I’m not sure exactly why that was.
nice Benchmade Griptilian 550 - 1 I got mine 2 years ago still works great. PS nice shop update love your videos and keep up the great work buddy. PPs. I don't know if you remember me saying about a knife drawing contest. and you replied with (maybe when i reach a certain Milestone on Instagram or UA-cam)
What an awesome set up! I've been looking at one of the retracting line set ups for my garage but when we move again I'll have to remember this set up.
Great video thanks for doing it. I just purchased the same kit today from princess auto. I'm curious, you mentioned that you bought a new distribution block localy. Can you tell me who sells them I'm asking because I live in calgary so we are neibours, I'm aslo trying to find a few more T connectors so I can install a couple more drops along the wall. Any info you can share is appreciated. Kind regards, Justin
You’re welcome and thanks for watching! Yeah Peavy Mart sells (or at least when I made this video) the fitting’s separately. I don’t think there is a Peavy Mart in Calgary but Strathmore, Airdrie, and High River all have them. Red Deer too if you travel that way at all 👍
Here’s a tip for you. Using the Teflon tape is only the first part. Then coat the the threads with plumber’s putty over the Teflon then screw it tight. NOT OVER TIGHT! It won’t leak.
Yeah I’ve heard a lot of folks doing that. When I worked in Oil and Gas we were strictly not allowed to do that. I was always wondering why but apparently it was for the hydronic circuits we were plumbing. I just have it ingrained in my head so much not to do that, that I can’t bring myself to do it in my own work. The pipes sealant works just great on it’s own though and has never let me down. A little quicker than taping and putty.
@@Simplelittlelife I learned the same thing. The instruction manual for the maxline says to use both, which bugs me. Thanks for your install video, it helped me prepare for installing my own system.
The reason you had air leaks is the aluminum blocks are not tapered threads for pipes. I had the same problem with a air regulator from china they don't use npt taps. Aluminum also does not hold threads well.
Ah that’s interesting. I never thought about that. I remember sometimes using manifolds that weren’t tapered and required an o-ring with a backer washer under the nut portion. I wonder if that is something similar to what these are. Thanks for the thought on that. 👍
3/4" or 1" would be a better main line. Ideally a ring around the perimeter with drops off it. Then a drip leg under each drop with a ball valve. Pop the handle off the valve and hang 1 by the compressor so you can grab it and just go around and open each one occasionally. Set a reminder on your phone maybe once a week/month to drain em. Or leave the valve handle on and put a plug in each one just finger tight just in case the valve gets bumped.
Great video, I laughed when you licked it lol. I heard you talking about this on your podcast but had to see the set up, the high speed parts were a nice touch too. Why do you need a dryer tank? I’m not familiar with that. Thx.
Thank you Mark! The dryer tank removes the moister created from compressing the air. It’s basically condensation and it can really do damage to air tools over time. Clean dry air (other than oil) make a huge difference in keeping those tools running well over time. 👍
Seems like the kit is no longer available. And has been replaced by what looks to be a 'cheaper' option with 1/2 press connectors or a similar option that has the advantage of Dewalt branded premium pricing .
I don’t think so. I just checked and every time I can see it I’m saying princess auto. Maybe it sounded like I said Auto Princess with my frozen tongue 👍
The moment I saw you stick your tongue to the aluminum (sorry, USA here ; ) ), I hit the thumbs up and subscribe buttons. Oh, btw... you might want to update your Princess Auto link to the product used in the video as it's a dead link now.
Your dryer is way to close to your compressor. From the compressor it should run into a tee with one line going down with a drain valve the other to the ceiling and over to your first drop where you would also have the dryer. The reason for this is to catch the water in your line . The air coming out of the compressor is hot so the water is in vapor and can go right trough the water separator.
You know…. You’re right! They came in and installed it for me while I was watching TV. What even is DIY these days anymore??? Right?! Your wisdom is so greatly appreciated!
@@Simplelittlelife guess I’ll move along you can’t even take a little criticism. I was hoping to see someone actually make their own system not buy one. To me, that’s DIY. Installing something from Amazon is, just normal life. Anyway, no worries I won’t be back for any of your other videos clearly your attitude is not who I want to watch.
For those that live in humid environments... In addition to the really nice dryer used in the video, it's not a bad idea to have a water trap and filter at each air station. Another tip: When you start your main loop, run it right up snug against the ceiling, then slightly slant the pipe as you run it around the garage so that it is going just slightly downhill. In other words, you'll be moving the pipe down the wall slightly as you go. This makes sure that any remaining water will run down to the next water filter at your next air station.
Another reason for wanting water traps/filters at each drop: The hot air will continue to cool and water will condense out of it even after it has gone through the large dryer shown in the video. That's the reason he needed to have 25 feet of hose before the dryer.... to allow the air to cool somewhat before reaching the dryer. The problem is the air will continue to cool down and shed moisture *after* it has left the initial drying canister. That's why you want to have a trap/filter right next to where you'll be plugging in your tool.
Drying canisters/filters/traps can't remove *all* of the moisture in the air. They can only trap the moisture that the air is shedding as it cools down. The air will continue to cool off and shed water all the way to the tool you're using. So it's important to filter the water out as close to the air temperature that the tool is going to "see" as possible.
One last tip: It's not a bad idea to use one of those cheap see-through water filters right at your tool connection. That way you'll see if you're in need of additional water trapping/filtering, and you have one last chance to dry the air before it enters the tool.
You'll only rust out an expensive tool *once* before you learn the importance of *dry* air.
When I originally plumbed my compressor in my 1200 square foot shop I had drops all over the place. Now I have a 100 ft hose reel in the middle of the shop and eventually disconnected the rest because I never used them. The hose reel is so easy to keep the hose neat and out of the way.
Yeah those hose reels are great. I do have a specific time when I need air on the other side of my garage and am also working in the middle of the garage where the airline used to run across the floor. For my applications, this one particular drop makes a huge difference. 👍
Three years later...and still very useful information. Thanks ( and I love the Spyderco Stretch, I have one too )
That would be so handy in my shop.... thanks for the laugh with the Christmas story moment on that manifold!!
Hahahaha! Pretty dumb of me wasn’t it? 🤦♂️
Ah yes doing a bit of air line upgrades here too. Those leaks can be a bugger. Thanks Jer!
Nice to see Canadian companies sponsoring Canadians!
Yeah I”m pretty excited about it 👍
Great system. We’ve used something similar in large dental offices.
The only suggestion I would make is putting the oil/water separator before your dryer. That drying medium works great to get water out, but will fail prematurely due to the oil coming from your compressor.
Thanks again for all your vids
Oh sweet! I never thought about that separator but that makes a lot of sense. Thank you for the tip. Glad you enjoy the videos and thank you for watching! Cheers👍
What sort of air compressor do dental offices use? I've been at the dentist's a lot lately and would like to know.
@@frostgfx most offices will use a dental or medical grade compressor. Some of these manufactures include Air Techniques, Midmark, Adec, Techwest, and so on. They use filters to reduce moisture and produce the cleanest air possible.
Some offices use "off the shelf" compressors and they have to incorporate dryers and filters to remove moisture and produce clean air
I thought myself, DON’T DO THE TONGUE TOUCH!!! Lol. Nice job on the air lines!👍
Hahaha! I thought that too but was again, just way to curious. Not sure why I keep doing that but sadly it isn’t the first time I’ve done that as an adult. Hahaha. Thanks! I’m really enjoying them. 👍
A canadian licking cold metal. ..most of learned that lesson before walking...lol
Hahahaha! 😆 Those who are smarter than me remember the lesson 👍
I used to build houses and commercial projects. I had an old plumber who use to work in natural gas’s installations. He told me the trick and it has never failed me especially with gas and compressed air installations. He used to tell the people he oversaw, “DO IT ONCE AND DO IT RIGHT”! Best regards. Richard
I am a collision shop sales rep for my day job. Your garage’s air flow set up is now neater than most body shops 😂🤣, they just drag 100ft air hoses around.
Hahahaha! Yeah, it gets the job done for sure. I’m really, really enjoying this setup. 👍
I installed the 1/2 inch system in my basement
love it
Right on! Piped, compressed air, in the basement...that is the dream👍
Hi Jeremy, I love your funny video. You are so personable. I have laughed a lot. Thank you for that entertaining time.
Thank you so much! I appreciate the kind feed back and thank you for watching! 👍
Oh boy Jeremy. I laughed out loud so hard when I saw you stick you tounge to the aluminum. Great air system by the way haha. Shop improvements always feel so good eh?
Hahahaha, right on👍 Yeah man they sure do.
Do a full loop for1/2" it will double the effective flow capacity in the main loop. Still have the short drops of 1/2".
I never want to see someone get hurt for the sake of a laugh... But... That made my morning. Hope your tongue is okay. It's also good to see that we all have our 'oops' moments. Stay safe my friend.
The system I went with suggested using teflon tape first then pipe dope on top of that when installing the fittings. Messy as all get out, but I didn't have one leak.
Interesting. I remember that when I worked at Sanjel (an oil company) we were not allowed to use both. Either one or the other. The bosses all preferred the pipe dope but it was a big no no to use both. I’m not sure exactly why that was.
That system blows Dude...👍🏻😜
Hahahaha! Yeah it does 👍
The "tongue test' gets you all the time.🤣
Hi bud, sorry for the ignorance, but what is the air dryer for , when your painting and is it a must have. Thanks mate👍☺️
nice Benchmade Griptilian 550 - 1 I got mine 2 years ago still works great.
PS nice shop update love your videos and keep up the great work buddy.
PPs. I don't know if you remember me saying about a knife drawing contest. and you replied with (maybe when i reach a certain Milestone on Instagram or UA-cam)
What an awesome set up! I've been looking at one of the retracting line set ups for my garage but when we move again I'll have to remember this set up.
Great video thanks for doing it. I just purchased the same kit today from princess auto. I'm curious, you mentioned that you bought a new distribution block localy. Can you tell me who sells them I'm asking because I live in calgary so we are neibours, I'm aslo trying to find a few more T connectors so I can install a couple more drops along the wall. Any info you can share is appreciated.
Kind regards,
Justin
You’re welcome and thanks for watching! Yeah Peavy Mart sells (or at least when I made this video) the fitting’s separately. I don’t think there is a Peavy Mart in Calgary but Strathmore, Airdrie, and High River all have them. Red Deer too if you travel that way at all 👍
Thumbs up just for the tongue touch to cold aluminum!
Hahaha! Some kids never learn😆
Awesome video, where did you purchase that dryer at and what size is it?
If i could of, I'd have given a double thumbs up for including those last 10 seconds
Hahahaha! Thank you 👍
omg i spit my coffee on my screen when stuck your tongue on that piece. lmao
Hahaha! Sorry about that but I’m glad you got a laugh out of it 👍
What was that secondary filter you added to the air dryer?
At 2:30. And you weren’t even Double Dog Dared !!! Impressive. :)
Hahahaha! Impressive, or stupid? 😆👍
Didnt even need anyone to double dog dare ya to do it lol!
Nope. I can do all sorts of dumb things just on my own 😆
Here’s a tip for you. Using the Teflon tape is only the first part. Then coat the the threads with plumber’s putty over the Teflon then screw it tight. NOT OVER TIGHT! It won’t leak.
Yeah I’ve heard a lot of folks doing that. When I worked in Oil and Gas we were strictly not allowed to do that. I was always wondering why but apparently it was for the hydronic circuits we were plumbing. I just have it ingrained in my head so much not to do that, that I can’t bring myself to do it in my own work. The pipes sealant works just great on it’s own though and has never let me down. A little quicker than taping and putty.
@@Simplelittlelife I learned the same thing. The instruction manual for the maxline says to use both, which bugs me. Thanks for your install video, it helped me prepare for installing my own system.
nice, always wanted one of those!
They work well 👍
Could you link the kit in the description please. Thanks
Pipe Dope is a must, to teflon tape is to iffy.
Can you repost the kit link please. I don't show it and couldn't find it on their website. Thanks
What do you call these hose..?
Great video, thanks
The reason you had air leaks is the aluminum blocks are not tapered threads for pipes. I had the same problem with a air regulator from china they don't use npt taps. Aluminum also does not hold threads well.
Ah that’s interesting. I never thought about that. I remember sometimes using manifolds that weren’t tapered and required an o-ring with a backer washer under the nut portion. I wonder if that is something similar to what these are. Thanks for the thought on that. 👍
Так приятно было начинать смотреть ваш канал! Видимо больше не будет рабочих процессов по изготовлению ножей?
3/4" or 1" would be a better main line. Ideally a ring around the perimeter with drops off it. Then a drip leg under each drop with a ball valve. Pop the handle off the valve and hang 1 by the compressor so you can grab it and just go around and open each one occasionally. Set a reminder on your phone maybe once a week/month to drain em. Or leave the valve handle on and put a plug in each one just finger tight just in case the valve gets bumped.
You obviously didn’t pay attention to the video…
Nice system, can you give me the information on the air dryer?
Thank you. The air dryer I got from princess auto and here is a link to their website: www.princessauto.com/en/detail/air-dryer/A-p8055757e
@@Simplelittlelife Thanks.
Good job!! I've got to to do this soon
the kit link is dead….
I no kidding LOL at that. My wife is wondering what the hell I'm laughing at on my laptop.
Hahahaha! Most folks are watching thinking “surely he isn’t that stupid?” 😆. Glad you got a laugh out of it.👍
Great video, I laughed when you licked it lol. I heard you talking about this on your podcast but had to see the set up, the high speed parts were a nice touch too. Why do you need a dryer tank? I’m not familiar with that. Thx.
Thank you Mark! The dryer tank removes the moister created from compressing the air. It’s basically condensation and it can really do damage to air tools over time. Clean dry air (other than oil) make a huge difference in keeping those tools running well over time. 👍
Seems like the kit is no longer available. And has been replaced by what looks to be a 'cheaper' option with 1/2 press connectors or a similar option that has the advantage of Dewalt branded premium pricing .
who makes the air dryer you mounted on the wall?
Get it at Princess Auto (Canada's Harbour Freight)
Plywood in your wall indicates that it's a shear wall. Structural engineering stuff.
For my system I used plastic water pipe and plastic connectors, that stuff is really cheap. I have 10 bar on my system and it works perfectly.
BOOM!! (shrapnell all over the place)
hopefully your plastic don't end up hurting etc.......... like blowing up .
@@hunkydude322 Unlikely, pressure proof 16 bar.
Did you ever do a video on a knife with a gut hook
I never have but plan on doing one in the next few months 👍
How good does the large dryer work?
Nice upgrade. You said Auto Princess at the end. Face palm deluxe. 😃
I don’t think so. I just checked and every time I can see it I’m saying princess auto. Maybe it sounded like I said Auto Princess with my frozen tongue 👍
@@Simplelittlelife I heard it on the one view, to be honest, I'd have to watch it again 'there may have been refreshments involved. 😆
Just checked. My bad! ✌
The moment I saw you stick your tongue to the aluminum (sorry, USA here ; ) ), I hit the thumbs up and subscribe buttons. Oh, btw... you might want to update your Princess Auto link to the product used in the video as it's a dead link now.
What kind of Canadian would you be if you didn't tongue test the cold metal!!
Hahahaha😆👍
That would be foolish for someone from Florida for a Canadian I need to know did you grow up in Vancouver? Thanks
Hahahaha! Nope. Alberta born and raised. 😆
“But the bell rang”
Your dryer is way to close to your compressor. From the compressor it should run into a tee with one line going down with a drain valve the other to the ceiling and over to your first drop where you would also have the dryer. The reason for this is to catch the water in your line . The air coming out of the compressor is hot so the water is in vapor and can go right trough the water separator.
Do a full l
Give the people eeeair Cohagen.
It’s not really DIY when you have a store bought kit is it?
You know…. You’re right! They came in and installed it for me while I was watching TV. What even is DIY these days anymore??? Right?! Your wisdom is so greatly appreciated!
@@Simplelittlelife guess I’ll move along you can’t even take a little criticism. I was hoping to see someone actually make their own system not buy one. To me, that’s DIY. Installing something from Amazon is, just normal life. Anyway, no worries I won’t be back for any of your other videos clearly your attitude is not who I want to watch.
Hey son, you need to go back to school boy!
What a stupid comment.