i think the pke module has issues, because i experimenting remove its fob detection antena it immediately lock the door and rang the alarm if you open its door or start its engine. if you did wired the whole system onto your car get a new spare unit just replace the module or antenna but most probably its the module. subscribe if helpful.
@@themaher1508 hi brother i unable to make full installation video as i did mind already. however there is alot of installation videos on this. but i just wanted to advice this is a messy system and risky, once the electronic has failed you endanger yourself or make the car totally halted until replacemen tunit is ready 🙏🏻
Hi ashraf ,the original immobilizer will removed from the original key and stick to the key slot receiver permanently as there is no need for immobilization anymore, the new alarm PKE features is more advanced with its GSM radar antenna to detect the key fob within 2 meter radius. Subscribe if helpful.
So it would not be a problem to install on altis model 2012? Because some say that the battery will weaken fast because of the system..and the original car alarm system is better..mind sharing your opinion?
@@ashrafrahim3665 Within 3 days If i not mistaken if there is no entry into the car the alarm will off its radar antenna system which will then allow u to enter using lock /unlock button. I been travel and set my car a week without starting I don't have much issue with it, plus my car battery is small NS60. Nothing much different
my car has 4 wire ignetion switch and this system has 6 wire . can you tell me how can i install this ? 2 wire extra . 1 is negative and one extra ignation . where i connect that extra ignation wire ? please help me .
Warning I have the EASYGUARD PKE system All remotes shit themselves at some point I advise when ordering to get two more remotes straight away because, after a couple of years, the new remotes will not work on the older module. I know because it happened to me.
Hello, I have installed my own but he can not start the engine , and the I try several time is the same, can anybody help me maybe there is a wire that I did not put
Hi I think will not compatible for car that already come with Factory push start system, like civic 2018. The diagram is universal for all car not specific to Honda, u might require a wire propping n tapping skill in order to look forward wires to joint with this module. subscribe if helpful 😃..thanks
I disagree, going from cold to hot creates condensation because air pressure difference in different temperatures. Since different air pressures have different humidity level, the leftover water condensates. if you wrap it in plastic, it basically condensates inside and cannot vaporize again because well, you wrapped in plastic, but it got inside with air, since you cannot make it completely air tight by wrapping it in plastic. So you just create a closed canister that keeps sucking water in from air. What I would to is get a can of spray polyurethane plastic and coat the PCB. Now its just protected from the environment. Ofcourse it is good to clean the board first with isoprophyl alcohol. Simple. And now the condensation water can leave before causing any harm by rusting your connectors, etc.
i had a more expansive system been using it for quite number of year, at the end of the days when the relays start to get weak, you will find your car will have a hard to start and sometimes doesn't even start. currently i haven't found any better system which is more reliable from china.
Hey my car already have keyless entry with remote key...but push start button is not there...if I install this then my old key can be programmed into this module...
Hi few things need to be clarify is your car keyless is aftermarket install? if yes the you need to completely get rid of it and install this PKE system old remote cannot be programmed if its not a universal ones. If your car keyless is OEM fitted then you totally cannot use this as it already have integrated into it's BCM functions and cannot be overwrite with this new keyless system. Another way if you only want to get push start feature is to just install a push-start only module but of course it have no other features other then to start the car and not as smart as this. Subscribe if its helpful
Hi, amazing diagnosis of the PKE system. I have one problem with my aftermarket PKE, it's that holding the brake and pushing the Push to Start button starts up the car way too fast, and this over time is causing some problems with the idling due to ECU. My question; is there any way for us to add a delay in the PCB when we start the car? only pressing the button without pressing brake sets car to "ON" position and starts the ECU, but when we try to start the engine, the starting sequence is Off -> Immediately Start Engine which does not help. Thank you so much for your input
as in modifying the PKE's PCB board is a NO, however I dont understand the sequence that you mentioned as in my PKE 1 time button push without brake tapping is ACC On. Push 2 is ON, and 3 will do start if brake is pressed or totall OFF if no brake pressed. The only thing that my PKE always bugging me is when it short crank before engine is start.
@@IkmalRusli Yes thank you for your reply. So push 3 with Brake pressed for my system does not go from ON -> Crank, but rather Shut off -> Crank. When this happens, it is similar to turning your keys straight to Crank, without pausing and letting ECU, fuel systems start up. Hope I'm able to explain well
ini tak plug and play bro kena wiring dan ada certain benda kena buat cnth backup kunci dan sebagainya, nasihat sy kalau tuan suka tambah2 accessories dalaman benda ni memang tak sesuai sbb consume sedikit battery untuk start up kalau accessories overloaded jenis battery kena tukar dari jenis NS ke DIN. subscribe sekiranya membantu 😊.
As for this system it's support most cars that comes with non-keyless system. There is 2 things you need to confirm with your car before installing or purchasing this: 1. your car default system should not be keyless 2.Door Lock system trigger, check your car or google what type of door lock trigger it uses cause this system only support +ve and -ve triggered. newer ford model uses datalink door lock system which not supported by this PKE system. Subscribe if I'm helpful 😃
good video and good eye for finding the bridge.. the chip though that looks more like they acid wiped or used a grinder on it to get rid of the writing on the chip so you would not know what it is .. I see that in all the products from china . They do it to slow people down from cloning the pcb's or dumping the firmware off the chip and the other reason is because the chip it self is a clone of a name brand.. I Just bought one of those to install have not taken mine apart yet but pretty sure that is the wireless section and that would not cause your car to turn on and off anyways.
hi for any type of pke alarm system it will consume slightly higher current then normal alarm system due to actively scanning for key fob transmitter. for this pke unit if there is no unlock for 3 days it will disable the pke function to reduce battery usage. so when u enter the vehicle u need to press the unlock button as pke sensor is disabled to conserve battery. subscribe if helpful 🤠
Yes it will for older cars with conventional engine start and +/- triggered door lock system. For newer Ford models that is using datalink for door lock this PKE system might not support.Subscribe if helpful.
I think you missed out the wire "Fuel Path/Pump" thats where the PKE sense if the engine is running, find the wire usually at the side door panel it will always give "+12v" when the engine running and non when its OFF. subscribe if helpful.
Tak perlu bro yang penting center lock dan door lock function, push start nj canggih cuma dia ada dia punya perangai tersendiri contohnya kadang kala signal dia terjejas sbb kan telepon bimbit dan kadang kala masa start up dia stop crank walaupun enjin belum hidup. saya masih menggunakannya sehingga sekarang syukur takde masalah sangat. subscribe sekiranya membantu 😊
@@IkmalRusli bro tnya sikit. Alarm skrng tngh gila. Now dia kacau signal. Sy kasi signal kanan, dia kluar double signal. Ni mmng issue alarm ke? Sbb alarm kalau sy tekan beeb berbunyi, tpi lampu signal tk kluar. Aduh pening.
@@nanotech4947 kena tgok bro kalau baru2 berlaku mungkin alarm controller ada masalah yg ini upgrade ke alarm ni mungkin solve issue bro ni, tapi kes paling teruk sikit bcm module rosak yg ini kena tukar bcm box. bawa ke pakar alarm dulu tgok apa mereka kata sblm upgrade ke benda ni takut jd teruk pula. Body control module (BCM)
@@nanotech4947 dah ok harga tu, masalah tiba2 start tu bukan masalah sistem alarm itu sebab kena air. rasanya semua alarm pke ni sama cuma make sure sensor antenna kunci tu ada 3 baru elok sikit mcm dalam video ni.
Mungkin boleh ..solder dengan cairan plastik atau..buat dia waterproof.. Boleh tak spray atau solder supaya tertutup .. Guna leakage spray.. Eksperimen ..hihi asalkan bahan penutup bukan elektrostatik..konduktor elektrik..
Idea yg agak baik tetapi harus ingat module tu ada connecter jenis socket...sekiranya kurang mahir akan menyebabkan socket sukar di buka sekiranya terdapat masalah😊
Sy punya remotenya termasuk dlm mesin basuh. Jd remote tu rosak.. Sy bole buka kreta mgunakan kunci manual.. Tp x dpt start kreta.. Mcm mna nak selesaikan?
Alamak tak ada spare ke? macam ni boleh bypass temporary kalau model alarm kamu sama mcm video ni. buka kereta tu manual time masa enjin tu mati tekan learning button yang dia provide tu hold sampai signal berkelip dan kamu boleh start kereta tu macam biasa untuk exit bypass mode tekan semula learning button tu masa engine mati sampai signal berkelip. Kalau beli remote baru untuk program hidupkan enjin kereta dulu, kemudia tekan learning button tu sampai alarm ada bunyi kejab dan signal berkelip, lepas tu tekan lock/unlock remote baru tu box alarm tu akan save frequensinya.setelah selesai programming tekam semula learning button tu.
This was an awesome video until you said to use the bag. This unit produces heat, if you bag This the heat will sit inside bag and literally make condensation due to the heat produced inside of the plastic. Recall microwaving a meal, the top plastic has water/condensation due to the heat being produced underneath. Maybe don't advise that.
friend ,it seems you like the car alarm product,we have the similar product,may be you will like it.you can add me whatsapp know more:+86 13417625973 our product function:keyless entry car;mpbile phone control car;smart watch control car;remote start...so on. www.ebay.com/itm/284267230545
friend ,it seems you like the car alarm product,we have the similar product,may be you will like it.you can add me whatsapp know more:+86 13417625973 our product function:keyless entry car;mpbile phone control car;smart watch control car;remote start...so on. www.ebay.com/itm/284267230545
friend ,it seems you like the car alarm product,we have the similar product,may be you will like it.you can add me whatsapp know more:+86 13417625973 our product function:keyless entry car;mpbile phone control car;smart watch control car;remote start...so on. www.ebay.com/itm/284267230545
bos nk tye sikit. kete kelisa 2003 sy xda central lock , xda alarm system. biasa la secondhand. jadi klau nk install natang ni nk kena install alarm dgn central lock skali ke? atau cukup natang ni dgn central lock shj?? mohon pencerahan
Kena pasang central lock dulu sebab sensor buka pintu dan auto lock Mechanism tak include.... Mmg banyak kerja sikit untuk kereta tuan ni lepas tu baru ble pasang alarm ni. Subsribe sekiranya membantu 🤗
@@IkmalRusli ooo baik2 bos. agak2 brp kerugian klau nk psg central lock tu standart kedai? agak2 je la harga lebih2 kurang. nk buat sndiri mmg xmampu la sbb wiring kete lama ni faham2 la kan. owner lama pun dah tambah mcm2 kt wiring dia , wire looping byk tp xtau apa function. mkin owner lama cabut balik kot apa yg dia pasang. tinggal wire je. sakit kepala jgk klau nk buat sndiri haha aaaa like je video ni xleh ke? ke nk kena sub jgk bos???
@@ejoi95 itu kena tanya Accessories bos sy rekomen kalau tak biasa buat better pegi dulu kedai Accessories dan buat basic lock unlock dulu sudah settle cukup budget baru buat yg ni...like pun ble je kalau tak nak subscribe cuma subscriber tu dia support padu 😁
@@rheillifestlouismuchapo3640 no totally no, unless you want the alarm to be app controlled together with gps function then you gonna add on module...which i dont buy
@@IkmalRusli where can I order this exact kit from? Would be really helpful if you added a link in description or just reply with a link please, thank you. [Just subbed]
Lock unlock indicator boss connect dkt mane yer?sy connect direct original horn tlalu bising..then sy connect p parking light tp x clear especially siang..ada cara x utk connect p signal light mcm original indicator bila lock n unlock?
You ble tap ke double signal wire switch output bukan input yg (+ve) kena test guna test pen kalau belum tekan emergency signal tu test pen dah menyala itu input, kalau tekan emergency light baru test pen menyala itu ouput...tapi btw alarm set tu sepatutnya dtg dngn speaker siren atleast tak kuat sangat mcm horn dan yg tu pun ble jadikan alternative
U cant still start the car the is a reset button u need to hold until the alarm chime then u can start and drive, to exit push and hold the reset button again
Hi. Can you show us what the reset button looks like? And i have another question, what if the battery dies of the remore or lost. Can i still use my original key to enter the car?
Hi bro, kurang faham sikit alarm box lama maksud yang car oem ke atau yang sudah upgrade?....kalau sudah upgrade depend on the installer dia letak mana but kalau factory installed bos tak perlu buat apa-apa plastik wrapped mcm dalam video ni. Yang dalam video ni untuk alarm yg installed after market or upgrade.
@@goldenlotuscaraccessoriese9927 hi bro, wayar starter tu you kena tap dari original key switch wire start tu kalau tak tau which one guna 12v tester dan turn the key to check each wire 1 by 1 ini untuk kereta yang original guna key to start. Kalau u punya kereta dah guna oem factory push start mmg susah sbb dia dah integrate sekali wire system ke ecu.
@@IkmalRusli sya punya toyota wish 2005 nfl, wire starter tak jumpa, sya test lain wire sudah dpt, starter wire je tak dpt, sya punya kunci punya, nk pasang push start punya
Not really sure what do you mean but my push start key fob is 1 way system alert is only through alarm siren from the car there is no indicator on the key fob if alarm is triggered like those viper system or may be u mean differently
Salam amin, saya telah memasang buat pemasangan PKE system ini namun saya tidak membuat video pemasangan disebabkan kekangan ruang bekerja yang terhad "ruang kediaman". Namun video cara pemasangan yang paling tepat seperti saya ikut boleh tonton di link berikut: ua-cam.com/video/QT-XmFuEGsw/v-deo.html
@@tankoiu Immobiliser tu dia akan buka cip dia dari kunci asal dan lekat kat leher steering starter kunci asal. Immobiler dah tak perlu sbb alarm keyless tu yg akan jd immobiliser nnti subscribe sekiranya membantu
Or just open it up and put alot of transparent nailpolish on it as a protective layer. Works like a charm
I would love if you would do a video on the complete installation of the unit in a car for the DIY persons please 👍
Do you think a silicone based or epoxy resin, if I coat the entire circuit board with one of them, it will prevent moisture from getting in there
i think so, yes correct that might be a good idea thanks for the input bro🤗
When you try to open a car computer or ecu,you will see a fully coated circuitboard just to insure resistant of water and rust on electronics parts.
Got it installed and used to not turn on with out the key fob in range but idk what happened it starts with out the fob I’m range what could it be
i think the pke module has issues, because i experimenting remove its fob detection antena it immediately lock the door and rang the alarm if you open its door or start its engine. if you did wired the whole system onto your car get a new spare unit just replace the module or antenna but most probably its the module. subscribe if helpful.
Hi Ikmal, would you please make a video about the full installation of this kit. Thanks
@@themaher1508 hi brother i unable to make full installation video as i did mind already. however there is alot of installation videos on this. but i just wanted to advice this is a messy system and risky, once the electronic has failed you endanger yourself or make the car totally halted until replacemen tunit is ready 🙏🏻
What if the car have immobiliser system?still suggested to install?
Hi ashraf ,the original immobilizer will removed from the original key and stick to the key slot receiver permanently as there is no need for immobilization anymore, the new alarm PKE features is more advanced with its GSM radar antenna to detect the key fob within 2 meter radius. Subscribe if helpful.
So it would not be a problem to install on altis model 2012? Because some say that the battery will weaken fast because of the system..and the original car alarm system is better..mind sharing your opinion?
@@ashrafrahim3665 Within 3 days If i not mistaken if there is no entry into the car the alarm will off its radar antenna system which will then allow u to enter using lock /unlock button. I been travel and set my car a week without starting I don't have much issue with it, plus my car battery is small NS60. Nothing much different
Thanks for the reply bro..but if the car already have push start button system..then cannot install this oem system right?
my car has 4 wire ignetion switch and this system has 6 wire . can you tell me how can i install this ? 2 wire extra . 1 is negative and one extra ignation . where i connect that extra ignation wire ? please help me .
My guess is Connect both ignition wires to one ignition in your switch. And just ground the negative. But verify, im noob
Warning I have the EASYGUARD PKE system All remotes shit themselves at some point I advise when ordering to get two more remotes straight away because, after a couple of years, the new remotes will not work on the older module. I know because it happened to me.
Me is a different story, mine has lock unlock issue and mis crank after 3 years of use.
Hello, I have installed my own but he can not start the engine , and the I try several time is the same, can anybody help me maybe there is a wire that I did not put
How do I get a 2018 wiring diagram for Honda Civic Sports model
Hi I think will not compatible for car that already come with Factory push start system, like civic 2018. The diagram is universal for all car not specific to Honda, u might require a wire propping n tapping skill in order to look forward wires to joint with this module. subscribe if helpful 😃..thanks
Hi bang,mana boleh dapat diagram untuk pasang alarm pke ni dekat wosh zge?
Boleh guide mana point nak ambil?
I disagree, going from cold to hot creates condensation because air pressure difference in different temperatures. Since different air pressures have different humidity level, the leftover water condensates. if you wrap it in plastic, it basically condensates inside and cannot vaporize again because well, you wrapped in plastic, but it got inside with air, since you cannot make it completely air tight by wrapping it in plastic. So you just create a closed canister that keeps sucking water in from air. What I would to is get a can of spray polyurethane plastic and coat the PCB. Now its just protected from the environment. Ofcourse it is good to clean the board first with isoprophyl alcohol. Simple. And now the condensation water can leave before causing any harm by rusting your connectors, etc.
Agree on technicall stand point
i had a more expansive system been using it for quite number of year, at the end of the days when the relays start to get weak, you will find your car will have a hard to start and sometimes doesn't even start. currently i haven't found any better system which is more reliable from china.
So is it better to get 2 of em?
This is good quality, i bought 2 unit as a spare incase. Mine is only failed cause of water intact.
@@IkmalRusli 🤔
Hey my car already have keyless entry with remote key...but push start button is not there...if I install this then my old key can be programmed into this module...
Hi few things need to be clarify is your car keyless is aftermarket install? if yes the you need to completely get rid of it and install this PKE system old remote cannot be programmed if its not a universal ones. If your car keyless is OEM fitted then you totally cannot use this as it already have integrated into it's BCM functions and cannot be overwrite with this new keyless system. Another way if you only want to get push start feature is to just install a push-start only module but of course it have no other features other then to start the car and not as smart as this. Subscribe if its helpful
Hi, amazing diagnosis of the PKE system. I have one problem with my aftermarket PKE, it's that holding the brake and pushing the Push to Start button starts up the car way too fast, and this over time is causing some problems with the idling due to ECU. My question; is there any way for us to add a delay in the PCB when we start the car? only pressing the button without pressing brake sets car to "ON" position and starts the ECU, but when we try to start the engine, the starting sequence is Off -> Immediately Start Engine which does not help. Thank you so much for your input
as in modifying the PKE's PCB board is a NO, however I dont understand the sequence that you mentioned as in my PKE 1 time button push without brake tapping is ACC On. Push 2 is ON, and 3 will do start if brake is pressed or totall OFF if no brake pressed. The only thing that my PKE always bugging me is when it short crank before engine is start.
@@IkmalRusli Yes thank you for your reply. So push 3 with Brake pressed for my system does not go from ON -> Crank, but rather Shut off -> Crank. When this happens, it is similar to turning your keys straight to Crank, without pausing and letting ECU, fuel systems start up. Hope I'm able to explain well
Salam bro..alarm ni plug n play je ke? Ke kene potong2 wiring jgk...walaupun keje elektronik, nak buat wiring kete ni leceh la
ini tak plug and play bro kena wiring dan ada certain benda kena buat cnth backup kunci dan sebagainya, nasihat sy kalau tuan suka tambah2 accessories dalaman benda ni memang tak sesuai sbb consume sedikit battery untuk start up kalau accessories overloaded jenis battery kena tukar dari jenis NS ke DIN. subscribe sekiranya membantu 😊.
Thank you my friend...such a good product review..
I wanted this on my Ford Fusion 2016 se, suggestions or thoughts?
As for this system it's support most cars that comes with non-keyless system. There is 2 things you need to confirm with your car before installing or purchasing this:
1. your car default system should not be keyless
2.Door Lock system trigger, check your car or google what type of door lock trigger it uses cause this system only support +ve and -ve triggered. newer ford model uses datalink door lock system which not supported by this PKE system. Subscribe if I'm helpful 😃
good video and good eye for finding the bridge.. the chip though that looks more like they acid wiped or used a grinder on it to get rid of the writing on the chip so you would not know what it is .. I see that in all the products from china . They do it to slow people down from cloning the pcb's or dumping the firmware off the chip and the other reason is because the chip it self is a clone of a name brand..
I Just bought one of those to install have not taken mine apart yet but pretty sure that is the wireless section and that would not cause your car to turn on and off anyways.
Very impressive diagnosis. Thank you for sharing your findings.
Hi can I ask does installing this will consume more car battery?
hi for any type of pke alarm system it will consume slightly higher current then normal alarm system due to actively scanning for key fob transmitter. for this pke unit if there is no unlock for 3 days it will disable the pke function to reduce battery usage. so when u enter the vehicle u need to press the unlock button as pke sensor is disabled to conserve battery. subscribe if helpful 🤠
@@IkmalRusli Thanks for the info, just subscribed! Hope to see more content on the PKE system
@@jaysonlai95 thanks bro, i will work more to create content like this if there is opportunity 😀🙏
Will this one work in a 95 Camaro?
Yes it will for older cars with conventional engine start and +/- triggered door lock system. For newer Ford models that is using datalink for door lock this PKE system might not support.Subscribe if helpful.
@@IkmalRuslihow do I bypass the Pke I have the ec003N
hello sir ,,,why is it if i remote start my vehicle the car will start but the starter keeps on starting even thow the vehicle has already started?
I think you missed out the wire "Fuel Path/Pump" thats where the PKE sense if the engine is running, find the wire usually at the side door panel it will always give "+12v" when the engine running and non when its OFF. subscribe if helpful.
ok Thankyou
Bro. System ni kena make sure alarm sedia ada elok ke? Sy punya alarm dah gila. Ingt nk pasang yg PKE punya.
Tak perlu bro yang penting center lock dan door lock function, push start nj canggih cuma dia ada dia punya perangai tersendiri contohnya kadang kala signal dia terjejas sbb kan telepon bimbit dan kadang kala masa start up dia stop crank walaupun enjin belum hidup. saya masih menggunakannya sehingga sekarang syukur takde masalah sangat. subscribe sekiranya membantu 😊
@@IkmalRusli bro tnya sikit. Alarm skrng tngh gila. Now dia kacau signal. Sy kasi signal kanan, dia kluar double signal. Ni mmng issue alarm ke? Sbb alarm kalau sy tekan beeb berbunyi, tpi lampu signal tk kluar. Aduh pening.
@@nanotech4947 kena tgok bro kalau baru2 berlaku mungkin alarm controller ada masalah yg ini upgrade ke alarm ni mungkin solve issue bro ni, tapi kes paling teruk sikit bcm module rosak yg ini kena tukar bcm box. bawa ke pakar alarm dulu tgok apa mereka kata sblm upgrade ke benda ni takut jd teruk pula. Body control module (BCM)
@@IkmalRusli bro. Berapa harga beli ni? Yg sy nk beli RM 420. Kedai tolong pasangkan. Agak2 kalau yg ni akan ada masalah start tiba2 ni tk? Risau juga
@@nanotech4947 dah ok harga tu, masalah tiba2 start tu bukan masalah sistem alarm itu sebab kena air. rasanya semua alarm pke ni sama cuma make sure sensor antenna kunci tu ada 3 baru elok sikit mcm dalam video ni.
Yang nie boleh masuk kat axia g 2017 tak
boleh bos semua kereta boleh, yang penting asal memang start guna kunci kalau dah factory keyless mmg x boleh. subscribe sekiranya membantu 😀
I am very impressed with the knowledge shared. I subscribed. I am planning to install one and I'm going to spray it with PCB protective spray.
thanks ...btw thanks for the sharing info on pcb protective spray...can u share the spray link so i can have a look 😃
How do you change the battery on the fob?
you can twist and split open the fob using coin or flat object. the batteries are same as in the computer bios CR2023.subscribe if helpful 🤠
Mungkin boleh ..solder dengan cairan plastik atau..buat dia waterproof.. Boleh tak spray atau solder supaya tertutup .. Guna leakage spray..
Eksperimen ..hihi asalkan bahan penutup bukan elektrostatik..konduktor elektrik..
Idea yg agak baik tetapi harus ingat module tu ada connecter jenis socket...sekiranya kurang mahir akan menyebabkan socket sukar di buka sekiranya terdapat masalah😊
mantap penerangannya. done subscribe,. tgh duk usha2 pasal pke, jumpa plk video tuan. tq byk2
terima kasih bro, sebab dah kena seram jgak bawa kereta tiba enjin mati brake tak function 🥲 tu buat awareness.
Hi, i am planning to buy the same one for my 2010 honda accord. What is ur suggestion, is this system good?
Hi jyo, been using the system for almost 2 years quite stable not much an issue with it and yes you can trust this one. subscribe if helpful 😎
Sy punya remotenya termasuk dlm mesin basuh. Jd remote tu rosak.. Sy bole buka kreta mgunakan kunci manual.. Tp x dpt start kreta.. Mcm mna nak selesaikan?
Alamak tak ada spare ke? macam ni boleh bypass temporary kalau model alarm kamu sama mcm video ni. buka kereta tu manual time masa enjin tu mati tekan learning button yang dia provide tu hold sampai signal berkelip dan kamu boleh start kereta tu macam biasa untuk exit bypass mode tekan semula learning button tu masa engine mati sampai signal berkelip. Kalau beli remote baru untuk program hidupkan enjin kereta dulu, kemudia tekan learning button tu sampai alarm ada bunyi kejab dan signal berkelip, lepas tu tekan lock/unlock remote baru tu box alarm tu akan save frequensinya.setelah selesai programming tekam semula learning button tu.
@@IkmalRusli terima kasoh tuan..
What's the link to site showing best selection of pke
www.alibaba.com/product-detail/New-Remote-Start-Car-Alarm-System_62226285971.html?spm=a2700.7724857.normal_offer.d_image.35b238f9qkFSz0
This was an awesome video until you said to use the bag. This unit produces heat, if you bag This the heat will sit inside bag and literally make condensation due to the heat produced inside of the plastic. Recall microwaving a meal, the top plastic has water/condensation due to the heat being produced underneath. Maybe don't advise that.
Thanks for sharing tips....
friend ,it seems you like the car alarm product,we have the similar product,may be you will like it.you can add me whatsapp know more:+86 13417625973
our product function:keyless entry car;mpbile phone control car;smart watch control car;remote start...so on.
www.ebay.com/itm/284267230545
Can I have this device diagram pls same one available with me I loose diagram pls
This pKE can share the purchase link ? Tq
hi jason, its in the description i get it from several vendor that is selling those if you have better price somewhere with same model
friend ,it seems you like the car alarm product,we have the similar product,may be you will like it.you can add me whatsapp know more:+86 13417625973
our product function:keyless entry car;mpbile phone control car;smart watch control car;remote start...so on.
www.ebay.com/itm/284267230545
What is the price of the product
Hi bro, check the description i attached the link to the produt
friend ,it seems you like the car alarm product,we have the similar product,may be you will like it.you can add me whatsapp know more:+86 13417625973
our product function:keyless entry car;mpbile phone control car;smart watch control car;remote start...so on.
www.ebay.com/itm/284267230545
bos nk tye sikit. kete kelisa 2003 sy xda central lock , xda alarm system. biasa la secondhand. jadi klau nk install natang ni nk kena install alarm dgn central lock skali ke? atau cukup natang ni dgn central lock shj?? mohon pencerahan
Kena pasang central lock dulu sebab sensor buka pintu dan auto lock Mechanism tak include.... Mmg banyak kerja sikit untuk kereta tuan ni lepas tu baru ble pasang alarm ni. Subsribe sekiranya membantu 🤗
@@IkmalRusli ooo baik2 bos. agak2 brp kerugian klau nk psg central lock tu standart kedai? agak2 je la harga lebih2 kurang. nk buat sndiri mmg xmampu la sbb wiring kete lama ni faham2 la kan. owner lama pun dah tambah mcm2 kt wiring dia , wire looping byk tp xtau apa function. mkin owner lama cabut balik kot apa yg dia pasang. tinggal wire je. sakit kepala jgk klau nk buat sndiri haha
aaaa like je video ni xleh ke? ke nk kena sub jgk bos???
@@ejoi95 itu kena tanya Accessories bos sy rekomen kalau tak biasa buat better pegi dulu kedai Accessories dan buat basic lock unlock dulu sudah settle cukup budget baru buat yg ni...like pun ble je kalau tak nak subscribe cuma subscriber tu dia support padu 😁
Very helpful, 👌
Is this product safe because I just ordered one
I am still using it in my toyota wish main car, no issue so far
@@IkmalRusli do I need to buy any accessories?
@@rheillifestlouismuchapo3640 no totally no, unless you want the alarm to be app controlled together with gps function then you gonna add on module...which i dont buy
@@IkmalRusli where can I order this exact kit from? Would be really helpful if you added a link in description or just reply with a link please, thank you. [Just subbed]
@@exileworldwide1814 the keyless system is called Q6B:
s.lazada.com.my/s.Xl4pT
I need help to u plz🙏🙏
❤❤❤Thank Q
Lock unlock indicator boss connect dkt mane yer?sy connect direct original horn tlalu bising..then sy connect p parking light tp x clear especially siang..ada cara x utk connect p signal light mcm original indicator bila lock n unlock?
You ble tap ke double signal wire switch output bukan input yg (+ve) kena test guna test pen kalau belum tekan emergency signal tu test pen dah menyala itu input, kalau tekan emergency light baru test pen menyala itu ouput...tapi btw alarm set tu sepatutnya dtg dngn speaker siren atleast tak kuat sangat mcm horn dan yg tu pun ble jadikan alternative
What happens if key fob dies?
U cant still start the car the is a reset button u need to hold until the alarm chime then u can start and drive, to exit push and hold the reset button again
Hi. Can you show us what the reset button looks like? And i have another question, what if the battery dies of the remore or lost. Can i still use my original key to enter the car?
Good advice
Ye kit khn se milygi
good job! thanks for sharing.
Alarm box lama dekat mn ye
Hi bro, kurang faham sikit alarm box lama maksud yang car oem ke atau yang sudah upgrade?....kalau sudah upgrade depend on the installer dia letak mana but kalau factory installed bos tak perlu buat apa-apa plastik wrapped mcm dalam video ni. Yang dalam video ni untuk alarm yg installed after market or upgrade.
@@IkmalRusli car OEM alarm
@@IkmalRusli utk starter wire dekat mn ye, dekat alarm sya Kena connect satu wire kepada starter wire
@@goldenlotuscaraccessoriese9927 hi bro, wayar starter tu you kena tap dari original key switch wire start tu kalau tak tau which one guna 12v tester dan turn the key to check each wire 1 by 1 ini untuk kereta yang original guna key to start. Kalau u punya kereta dah guna oem factory push start mmg susah sbb dia dah integrate sekali wire system ke ecu.
@@IkmalRusli sya punya toyota wish 2005 nfl, wire starter tak jumpa, sya test lain wire sudah dpt, starter wire je tak dpt, sya punya kunci punya, nk pasang push start punya
How mush this price bro??
Hi Bro there is a link in the description with multiple vendors selling those
Very dangerous. I will skip this upgrade.
so far the unit in my video performing very good...but again the risk is there mistake could happens
thanks you man
Benda ni tahan lama x bos. Ke mudah rosak
So far saya guna ok, problem haritu pun sebab terkena air.
@@IkmalRusli da berapa lama guna bos
@@synonymspicturefilm5648sblm tukar kena air tu dah 2 thn ...yg baru tukar ni dah 9 bln
@@IkmalRusli psg sndri ke bos. Area mana.
@@synonymspicturefilm5648 ye, betul tapi kalau tak tahu beli barang je banyak kedai accessories boleh buat
Waiting for installation video
Remember:Most push start systems alert you when a crimal tries to steal your car.
Not really sure what do you mean but my push start key fob is 1 way system alert is only through alarm siren from the car there is no indicator on the key fob if alarm is triggered like those viper system or may be u mean differently
Good content.
Yea no I won’t buy if it will fail
Mantapp jo
Bahaya pok kalau teda spare, canggih tapi boleh jahanam kereta
Tq bro....
Plz help me
Cara instal plak d tunggu..
Salam amin, saya telah memasang buat pemasangan PKE system ini namun saya tidak membuat video pemasangan disebabkan kekangan ruang bekerja yang terhad "ruang kediaman". Namun video cara pemasangan yang paling tepat seperti saya ikut boleh tonton di link berikut:
ua-cam.com/video/QT-XmFuEGsw/v-deo.html
@@IkmalRusli bro macam mana kereta yang ada immobiliser?
@@tankoiu Immobiliser tu dia akan buka cip dia dari kunci asal dan lekat kat leher steering starter kunci asal. Immobiler dah tak perlu sbb alarm keyless tu yg akan jd immobiliser nnti subscribe sekiranya membantu
thanks for the valuable information ! Like and Sub !
thanks for the subbed bro 😊😊
kereta berhantu kot haha
serius pucat jgak bawa enjin tiba2 mati brake tak function ...seramm 🥲