How to Make Wind Turbine Generator - Clean Energy
Вставка
- Опубліковано 28 вер 2024
- How to make Wind Turbine
Music By NCS:
Track: Lost Sky - Dreams [NCS Release]
Music provided by NoCopyrightSounds.
Watch: • Lost Sky - Dreams | Tr...
Free Download / Stream: ncs.io/DreamsYO
Track: Jim Yosef & Alex Skrindo - Ruby [NCS Release]
Music provided by NoCopyrightSounds.
Watch: • Jim Yosef & Alex Skrin...
Free Download / Stream: ncs.io/RubyYO
+ Thank for watching!
+ Please subcribe to view the latest videos.
+ Good luck!!!!
When the wind changes it could rip the wires out by wrapping them around the pole. The design fault I encountered years ago and needs to be transfered to a brush plate that will allow the generator section to fully rotate 360 without hinderence. Insulated copper rings would work rotating on each other like a bearing with wires soldered from the generator on the top one and the feed wire to the bottom one.
Where can you buy that type of bearing
For anyone whom might be wondering the MOTOR used is a 3 phase ac as to the 3 phase full bridge rectifier to change the sine wave from ac to dc so that he could use it to charge his phone but yhe problem is 12 volts which isn't good for charging phone batteries as to why most phone chargers out put is 5 volts at around 1 amp now as to the amps of the d.i.y. wind turbine wasn't shown so that is a mystery but overall it's a very nice project to try.
This is very helpful thank u
why 12v is not good for charging phones?
@@manginasal2950 yeah I wonder too... 12v is more than most charger outputs but less than the home charger's input is but a phone charger meant for car would work just fine imo. I wonder only if the amps are enough to actually charge?
@@jk8557 لا الامبيرات ليست كافية لشحن شاحن بطارية المحمول محول من 220v الى 5v بالنسبة لهذه الطاقة تردد مستمر 12v ومافوق لذالك يجب وضع منظم ياصديقي
There is my fii..it's been a while since I want to do one of these and I get discouraged but seeing this one I can't wait to start making mine. Very good !!! 👏👏👏👍👍👍
Me too..
@@Dikpurnomo ok
Me too
The video is appreciated, but no parts list is bad form.
I found this motor for use:
12v 12000rpm De Alta Potencia Dc Gran Torque 775 Motor Bola (Spanish) It's a 12v, 1,200 RPM DC 775 motor.
LOL, I knew you were going to put those blades on wrong as a lot of people do that. Fan blades are meant to blow at you but for a turbine you need it to blow behind it (if it were turned on) so reverse the blades and it will work a lot better.
great video!
As long as it's a DC motor it is very legit...i may be wrong but i believe AC motors have an issue generating power..the bigger the DC motor and the propellers the better. though get too big and you may need to install a brake system as to not blow motor during high winds.
i would implement this idea combined with a "handtruck", 55 gallon drum, shelved and door modded of course..., deep cycle gel batteries, some solar panels,and a good chargeing computer and you would have a pretty solid mobile free energy(besides initial cost) power plant...
if your lucky you may be able to aquire the solar panels that also create energy from rain(or rather most likely just transfers the kinectic energy on the water droplets(which could be collected for drinking) into electrical energy that we can utilize)...
cheers...
I'm that's not a DC motor. It's a three phase AC motor connected to a three phase full bridge rectifier to change the polarity from AC to DC without a voltage regulator.
Gió mạnh như vậy chắc đối diện quạt máy. Điều kiện lý tưởng này chỉ để tham khảo. Thiết bị đẻ trên đỉnh núi hay ngoài bãi biển thì may ra. Cám ơn youtube của bạn
Nice simple design from scavenged parts, thx! Your balcony looks one way so twisting wires isn't a problem, but just discovered slip rings in different wire configurations, which should solve my 360 degree rotation.
You need to build a slip ring to take the power off and the wires will not become tangled.
I was wondering why he didn't do something like that.
Eldktroautos
PLease add a link with all the components you used in this build. Thanks :)
that is so cool!! i would love to try this but I'm not sure what are the names of some of the parts you use
what do u have questions about?ik this was from a long time ago but if ur still looking for the answer I think I can help
@@joaquingarcia2675 What is the name of thing he connects the wire to , what it is for? (the thing that's on the stick.
Pls.
I tried it on a small scale....it just worked fine :-)
Please list the components used
Cool.. got interested to make one myself. Very useful free energy generator and easy to make.
dear NDA HACK, plz enlist all components in DISCREPTION of the video.
nda hack
He started charging mobile and my mobile :less than 20% battery remain
😂
tf
Nice turbine, seems like a fun project to make
Do you have the materials list please? this video is great
Nice projects 👏👏
Okay but how to run a wire through the body without the wire twisting? I want to get the power further out.
Hey am a scholar ,would have been really helpful to have ,items needed list especially for projects but thank u for the practical explaination
For a scholar, you could use some lessons in grammar.
Very beautifull work. Creativity is very good
👍👍👍good Creative and job....for 360 rotation my be Problem wire but is ok👍
Great one, I want to make one that is lot bigger, I want to pump water with that current.
Do it without the music
turn off the sound...lol
i guess so
So many folks around UA-cam can't seem to concentrate when they hear music. (Undiagnosed ADHD perhaps... I don't know). Yet it never occurred to them to... _turn the sound off._
Do us a favor and fuck off
Add please
Very nice material. Congratulations!
yeah can u give us a list of parts u used in the description below pls
Good question
Now if you only had a million of them you might be able to power a house
aside from the obvious large appliances like Clothing dryers, fridges, etc, EVERY single device in your home has a 120VAC power supply that drops the voltage to between 5 and 24 volts DC to operate.
It makes more sense to convert the items to be powered to run on DC plugins and use this type of system to power those items and eliminate the entire 120VAC to X volts DC power supply.
Very good 👌👌
O problema do motor sozinho e que há duas correntes de eletricidade sentido horário, e sentido ante horário, oque pode acabar queimado a bateria, faz um equipamento elétrico com o carregador de celular para a corrente ser apenas 1
That's a three phase AC motor connected to a three phase full bridge rectifier then to the load. Since the motor is a three phase AC motor it doesn't matter which direction the motor is turning because the current goes back and forth between what the motor is connected to. AC is short for alternating current. Now add that three phase full bridge rectifier and the current is changed from AC (alternating current) to DC (direct current) which is single phase which is what most of what we use requires for normal operation.
Nice one Broo...
Hey dude what is the RPM of your dc motor?
Bruh what are you talking about it’s not a dc there made exactly for this to create energy
Now, the next project is, harden it so its useful at CAT3 Hurricane. Now we are talking useful for when the power is needed! Great inspiration though! Combined with other methods, you could charge a bank of batteries if you live in the right area!
It is amazing I like it so much I will try
And what is the box you put the wire
Hi ! Can i use ur project as a reference for my school project and i develop of it? Thank pls reply
Very nice to see this project , can we attach car generator for more energy
Very good good good work👍👏
I'm very happy alhamdullilah 🙏🤲❤️
Very decent presentation. 👌👍
I am gonna make this in my channel... Let's try its gonna work or not.
I need your support to try this. Support our village science channel.
Toy...you 'might' be able to charge a cell phone on a good day. Voltage reading alone means nothing until you connect it to a load.
....and don't forget about the current [amps] side of the problem.
I'm just having a problem about the wire attached to the turbine.. What it there is a storm and the wind direction change frequently I'm sure there is a high chance of the wire to be wrap around the stand tube then it will snap
Waar koop je een generator, voorstelling is mooi, zou je zelfs stelselmatig kunnen vergroten en verzwaren tot je de truc beet hebt, maar waar koop je verschillende generatoren????
Awesome video. Can u explain how to save this energy in battery.
Connect it to a power bank, thru a USB car charger
Can you tell me motor specifications and it has three connections an ordinary DC motor has two?
Super bro mechanical projects poduga bro...
likeeeeeeeeeeeeeeeeeeeee
good work
samvel yeghiazaryan
Roses are red, violets are blue, wanna build a solar panel but have no clue
the output you are showing is fake.
Maximum efficiency a wind turbine can achieve is 59.3%. At 6:01 you are showing 18.1 volts. How is it possible????
good video. i will try this it!!!
where did u get the voltage stabiliser and charging module I am doing a similar project and I need these exact parts really soon could u pls tell
anish kanduri did u ever get the voltage stabilizer and charging module if so where?
awesome
Good except there is a problem that nothing prevents the wire from winding around the pole. needs a connector that allows the mechanism to rotate freely without winding the wire around the pole.
Классико- эстетикой!
Would you be able to use the motor of the fan as your generator??
Done with a vertical axis blade, the wire would not have a problem with 360 rotations.
what have you used
jajakallha Khairan জাজাকাল্লাহ খাইরান
Can you reverse the wire or turn the blades around on the fan to make the fan a wind generator?
Excellent video very well done!!!
Wow
Thank bro
nice video
Cool!
It will charge a Tesla in about nine years!
So you are here to find free pvc tesla charger? Wow
We love your wind turbine - clean energy! Thank you!! Now SUBSCRIBED!!
Bhai time waste na kar
You should run the wire through the center with a bigger bearing and down the shaft so it won't get wound up around the exterior
That could reduce the problem to a point but the wire would still get twisted inside the pipe and it would be a lot harder fixing that
fake video
Tell me why?
cause when you plug mobile to charging even turbine doesn't slow
NDA Hack how it sewing fast
Tomaš Marcin Tomaš Marcin Mobile phone not take too much power..
Only when give full heavy load then turbine slow...
NDA Hack how it sewing fast
cool
So what stops the wire that runs down the tube from getting all twisted up over time?
you should have used tie straps instead of hose clamps because of weight and can disrupt motor
Is it 12v motor or 12v dinomo moter
Thank you
Nice
Bonjour 😊 quel est le générateur de cette petite éolienne 😉 merci
works better as a generator if you turn the power off on the motor and let the wind blow it
Every time I click a video like this I get disappointed that there’s nobody talking and explaining the process
use can u motor 775 dc rpm motor or 1200 ....12volt this make toU just needG
Well geez, that clears it up 🤦♂️
Pure Engineers I guess? Expert in Engineering and creations but not with Teaching.
Bcs this is incomplete project there should be slip ring for collection of power to minimize the rotation effects .
Yeah plus how will you connect it to your house like bro you have the turbine but How will you connect it to something like a charger for example
great video!
As long as it's a DC motor it is very legit...i may be wrong but i believe AC motors have an issue generating power..the bigger the DC motor and the propellers the better. though get too big and you may need to install a brake system as to not blow motor during high winds.
i would implement this idea combined with a "handtruck", 55 gallon drum, shelved and door modded of course..., deep cycle gel batteries, some solar panels,and a good chargeing computer and you would have a pretty solid mobile free energy(besides initial cost) power plant...
if your lucky you may be able to aquire the solar panels that also create energy from rain(or rather most likely just transfers the kinectic energy on the water droplets(which could be collected for drinking) into electrical energy that we can utilize)...
cheers...
The volt meter is on DC...not AC. So that would be DC. A full bridge rectifier could be built in. A motor no, but a generator yes.
Plz give instruments name ,
Sizes, model name
Sorry, but the music doesn't explain what you're doing or where you got the components.
.
That what im saying
Bill Csexorobbett
Jeovania Angelica
LoooooL ... true.
Wire problem for 360 degree rotation ?
Could always get a slip ring connector. But you'd be better off using that for an actual turbine, this thing isn't really worth putting one of those on anyways
Not A Big Pblm.We Can Easily Solve This Pblm
360 degree ki problem dur kro ese to koi bhi bana leta h ji
@SKEND EDRBEU Fixed position. Move it by hand. Whew.. careful.. might break a sweat.
Yes, he should this problem! Good ideas!
nice thing. please give me a list of the parts, specily the voltage stabiliser
Type SQL50A1000V on google and you will find it
@@thomasmarky9298 thank you. Have a nice day
Greetings Peter
@@praradable You too
I'm very impressed with the voltage reading. Can you kindly share the components used ?
So that I can try to replicate what you have done.
I want to a small wind turbine project for my University project semester, what voltage produced from small wind turbine for project. Please help me, sir... What type(rpm) of dc motor use for wind turbine for University small project. Please tell me, sir..
@@torikulhasan8984 How did it go?
@சிஜிபி dynamo or dc motor?
محرك ١٢ فولت سعره دولار
i also want to know what the components are so that i can make a small field of these in my backyard because of loadshedding :/
instead of putting music you can just talk or explain
do you have a list of the parts to make this. and where can i find them?? thank you
The motor is a 220v three phase brushless ac motor
And a fully bridge
rectifier
I made it by myself. I used Avasva solutions for that.
Is it works?
@@muhfaiz808 YES ! ! !
@Abhimanyu Rajesh wdym?
@@shantelleadeline6053 You're pretty 😍
Can someone tell me what is the name of the green thing at the end?
6:09
wow, im definetly making this
SO many red flags that this is faked, lol.
This isn't that hard
I mean if you think its fake then obviously you dont know science 🤷🏻♀️ unlike most videos i didnt see anything fake here.
Nice idea but without the actual components used, this helps no-one. You might want to list the specific components used in the description (Like the motor you used to function as a generator for example).
Scott he's using a three phase AC motor as a three phase generator and a three phase full bridge rectifier to change the three phase alternating current to single phase direct current to either power a led light or to charge his phone when there's a power outage.
You can search the internet for the motor and fan blade he's using.
@@jclowe735 What kind of motor is it? brushed or Brushless? Brushless is more efficient and the one here appears to be brushed but that's just an observation based on what you can see through the housing of the motor.
What's the Blade length, Pitch, width? weight of the fan?
Adding a random fan blade to a random motor can cause problems such as rotor cavitation where beyond a certain speed it will vibrate beyond the capacity of the armature shaft to withstand it and damage the motor.
I'm very familiar with the concept of 3 phase motors. I build and fly Brushless RC planes which are 3 phase and you can use their power systems to generate 120Vac via an inverter and a 3S battery cell to power pretty much anything depending on the C rating of the battery and how long depends on the mAh rating.
From what I see here, it's a concept with too many variables that will fail. Even in the video of it operating you can see it vibrating badly. I can achieve the same thing with an Inrunner Brushless motor that's literally 3.5 cm in Diameter and 7 cm long through an ESC 3 phase speed controller.
The problem is if you use a fan blade too great a length or blade pitch, you'll burn up the motor (Literally).
Very inventive but without a proper parts list, it's still concept with too many failure points.
wire will break when it will rotate continuously
Jaspreet Brar
Yep, and if I built it that would happen with a half hour of setting it up.
Slip ring contacts work but on a simple rig like this simple pivot stops that prevent the rig turning more than 180° are sufficient.
_Why does no-one make vertical rotation generators. Much easier to wire and only slightly less efficient_
Obviously It will I thought it too,,
My English not so good in writing and Grammer. Sorry for it. It is easy to sort out this little problem .
Can you do a list of the materials that you had used for this project? Thanks
POV : your here for a school project
Nope because the pandemic made us bored
Yup
No
You're* stay in school people
He is bluffing , he is powering up the DC motor by external source
The DC motor here used is of 12 v
He's using a three phase AC motor just pause and look at the three phase full bridge rectifier and he may have had a fan out of frame when he connected the multi meter to it oh just pause at 5:42 and look at the wires and you'll see three of them and the only way to use it as a motor is by connecting an ESC (electronic speed controller) with a radio and receiver for to be as a motor...
This is great! Are there any downloadable instructions that one can follow with listed parts? I wouldn't have a clue on some of the bits :p
Yes
Lack of details for what the name he put it.
Fake, thats why he not mentioned the components
Topi huru
Solar energy 4 ma 3 1 kum
3 la 1 hevy cells consver sun solar can ru ñ
1=3 +1 (1)=wind Moter milll power appply rota it Moter tide bald genator inventor
Aaj date hai 24-9-2020 sir ye Jo voltage stabilization AC DC hai kitane Ka milta hai
Maine aaj kharida 70 ka hain Ek Dynamo
Cool. Could you kindly clarify, what is the last detail you join to hull?
0:27 i have this dynamo motor i have 2 ok? can i use one to this turbine it's work please tell me😢
That music was %$# horrible! Kept the sound on because I thought you might say something. :(
* Arto Lauri upia kanava tilaten tästä nyt. Niin siis itselle, kuin ihan kavereille myötään.
You should give a list of the items you use in the project other way is a waste of time!!!but I like it