I have to do this to my sons 93 Accord today, and I'm using this video. I have to purchase the 21 & 19 mm wrenches. I keep hearing about only using 'flared' wrenches, but they aren't using two wrenches for better stability. Wish me luck. 😎
@@CB7Media the problem is that one of the lines just goes 3 or 4 threats and won't go any further and leaks the fuel.but when I put the original one I have 0 problems.
I had to slow down the video to find it, but you literally reafed out that air intake temperature sensor to get the hose out without saying that needed to be removed or showing how to put back in. I struggled with getting that fat ass hose out because of that
Hey i have a 91 honda accord and i took the kids to school when i came back home n parked my car turned of ..it cranks now but wont turn on battery is charged i have full tank of gas n i put a new ecu fuse can it be the pump?
It could be the pump do you Hear it priming up when you turn the key or no ? If you think it's the pump then loosen the hose on the filter to check for pressure. If you have pressure check for spark could be the dizzy. If you have spark then check your ignition switch. Do you have a check engine light on by any chance?
@@CB7Media after 2 days of replacing the distributor my ecu fuse kept burning out i got stuck in the supermarket i replaced like 5x the ecu fuse before i was able to pull off and go home quick .....can the be spark plug wire making a short or do i have to replace whole fuse box ...it kept burning the ecu fuse only like 4 of em within seconds
Do you know why my new fuel filter would be leaking? I put the new little washer in there and everything and made sure it screwed in right and wasn't stripping the threads and it's leaking gas out of the right smaller hole when I run the car. Took it apart and put it back together 4 times and even bought a new fuel filter and no matter what it leaks every time. I've looked at every single one of these videos on UA-cam and it doesn't seem to be happening to anybody else
@@CB7Media that's what I thought but I actually tried it without the washer the first time I hooked it up and it leaked that first time too, which led me to believe I was supposed to put that third little washer in there but maybe it wasn't threaded in there right the first time. If so do you know what that third tiny washer that comes with it is for?
The 3rd washer comes for no reason the fitting itself should fit in double check and make sure that the end of your fitting is not flattened out and still round to fit in
I am trying to figure what I am going to make a mounting bracket out of and where I am going to put it. I can buy one all ready set up or make my own. I would rather customize my own I have plan's just have not gotten to it yet but it will be coming sorry for the wait lol
Nicely done video. No waste of time, clean views and instructions. Really helped me out.
Glad I could help
Did mine this video help a lot thank you.
Great video...excellent
I have to do this to my sons 93 Accord today, and I'm using this video. I have to purchase the 21 & 19 mm wrenches.
I keep hearing about only using 'flared' wrenches, but they aren't using two wrenches for better stability.
Wish me luck.
😎
I tried 3times and my cb7 won't accept the aftermarket fuel filters any suggestions?
@@ezequielbarraza9878 This procedure worked out fine for me. Took about 30 minutes.
What is the problem ?
@@CB7Media the problem is that one of the lines just goes 3 or 4 threats and won't go any further and leaks the fuel.but when I put the original one I have 0 problems.
If it's the main full line then it's a steal line take out the copper O ring and it will work fine
Before you do anything, you should disconnect the battery and relieve the fuel pressure from the system.
I had to slow down the video to find it, but you literally reafed out that air intake temperature sensor to get the hose out without saying that needed to be removed or showing how to put back in. I struggled with getting that fat ass hose out because of that
Hey i have a 91 honda accord and i took the kids to school when i came back home n parked my car turned of ..it cranks now but wont turn on battery is charged i have full tank of gas n i put a new ecu fuse can it be the pump?
Or fuel filter?
It could be the pump do you Hear it priming up when you turn the key or no ? If you think it's the pump then loosen the hose on the filter to check for pressure. If you have pressure check for spark could be the dizzy. If you have spark then check your ignition switch. Do you have a check engine light on by any chance?
It was the distributor was shot no spark to ignite the spark plugs smh quick fix thank god
@@CB7Media after 2 days of replacing the distributor my ecu fuse kept burning out i got stuck in the supermarket i replaced like 5x the ecu fuse before i was able to pull off and go home quick .....can the be spark plug wire making a short or do i have to replace whole fuse box ...it kept burning the ecu fuse only like 4 of em within seconds
@@geo_nwk_9739 did you ever figure it out? could be main relay
Do you know why my new fuel filter would be leaking? I put the new little washer in there and everything and made sure it screwed in right and wasn't stripping the threads and it's leaking gas out of the right smaller hole when I run the car. Took it apart and put it back together 4 times and even bought a new fuel filter and no matter what it leaks every time. I've looked at every single one of these videos on UA-cam and it doesn't seem to be happening to anybody else
Don't put the washer in the right side it's not necessary and makes it leak
The only thing that needs washers is the banjo bolt
@@CB7Media that's what I thought but I actually tried it without the washer the first time I hooked it up and it leaked that first time too, which led me to believe I was supposed to put that third little washer in there but maybe it wasn't threaded in there right the first time. If so do you know what that third tiny washer that comes with it is for?
The 3rd washer comes for no reason the fitting itself should fit in double check and make sure that the end of your fitting is not flattened out and still round to fit in
@@alexw1953 did you end up fixing the problem ?
Still waiting for that toggle switch lol
I am trying to figure what I am going to make a mounting bracket out of and where I am going to put it. I can buy one all ready set up or make my own. I would rather customize my own I have plan's just have not gotten to it yet but it will be coming sorry for the wait lol