replace the voltage regulators with LM7805. had my 16.4.2 kept freezing up and sent it back to presonus for about $350 total a few years ago. said they replaced the board but they only replaced the voltage regulators with the same lame voltage regulators. 2 years later board freezes again, now prosonus says board out of service and wont fix it. found a guy to actually replace voltage regulators with beefier LM7805. so far no problems a few months in. good luck. dont have to toss a board where no parts can be salvaged. crazy design that they become disposable.
if the fire wire module is malfunction/damaged so far I have replaced it with a complete firewire module, because the factory only provides that part. and if later I can repair the module, I'll share it on my UA-cam channel.
Muy buen video, solo que tengo una consulta, no se si sea normal, pero compré una consola de estás usada y como a los 30 min activa se calienta mucho según mi punto de vista, y el dueño anterior dice que en ocasiones dejaba de mandar audio del Main, eso no me a pasado, pero en dado caso, cuál sería el problema y como saluvionarlo?. Si se necesita comprar un módulo completo en dónde lo podría encargar?. De ante mano muchas gracias.
Lo más importante es modificar la parte del regulador DC-DC del módulo DSP, reemplazándolo con el LM7805 IC (ver minutos de video 2:38 a 3:18). el sonido se pierde a veces no hay ninguna causa que el regulador de DC-DC sea inestable. ua-cam.com/video/5W9qCBr4LrY/v-deo.html
Hi, I have a SL 16.4.2, I will be buying the IC 7805 as per your recommendation. But just before i buy, I just have a question and I hope to get an answer from you :) I have a problem with AUX 1. The volume level is sometimes okay, but then after a few minutes the volume will suddenly drop a little bit, then go up again, then drop again.. Do you think i should also check or replace the pots inside AUX 1? Or the IC 7805 should fix the problem? Thank you again for your content, I really appreciate your posts.
Problem about AUX you should also replace the capacitor 4.7uf 6.3V in the DSP module, there are 24 pcs. and If you have free time, it's better if you replace all the capacitors with metal bodies in the DSP Module. because if the use is over 5-6 years this capacitor will be damaged so that symptoms will appear abnormal symptoms in the master or Aux outputs
I don't have a video about replacing the capacitor DSP module for SL16.4.2, if i have time i will make it later. but an example of replacing the capacitor on the DSP Module can be seen on the SL 16.02 video here ua-cam.com/video/aGIYGXLOHgk/v-deo.html&t= 55s
@@creativera2180 Thank you I will wait if ever you get the chance to make that video! Would really appreciate it :) In the mean time ill install the IC 7805 for now
@@kelvincortez3283 in the DSP module there is a flexible cable that is connected to the LCD. be careful when disassembling this mixer, do not damage this cable
@@creativera2180 Hi again thank you :) Im disassembling the mixer now, all is going well, i just have a problem with the LCD ribbon/film strip cable, how did you pull it out? I dont want to use excessive force, but its tricky pulling it out
Buenas noches colega. Buen video. Le cuento que tengo una consola igual pero la falla que tengo es que no activa ningún phantom power. No se si me pueda ayudar. Gracias
El circuito de alimentación Phantom de 48 voltios está en la sección de la fuente de alimentación SMPS, puede haber un transistor defectuoso, llévelo a un distribuidor autorizado. Spain PreSonus Europe Limited Unit 1 & 2 Cavan Enterprise Centre, Dublin Road, Killygarry, Cavan, Co Cavan, www.presonus.com/buy/international-distributors
Buenas, tengo una 16.4.2 hace como 10 años. Los reguladores de FAT CHANNEL me rotan solo, no fisicamente, sino que en las ganancias, frecuencias, me suben o bajan solo ( por lo general tienden a bajar mas que a subir ), no solo una perilla, sino en casi todas. En general siento que están duras los reguladores rotativos ( creo que son encoders y no potenciometros ), se le puede echar lubricante tipo W40 ? Porque usé un limpiacontacto ecologico de contacmatics tipo CO2, pero no sirvieron para nada, me los endurece mas por el frio pero despues no me corrigen el problema. saludos !
This looks similar to my 16.0.2, and after replacing the voltage regulators, i was flabbergasted by the fact that the only connector that the BNC "lamp" connector's cord can reach, is a ground pin on the chassi. WHAT?
as chek R10 ohm 10 module I have to chek I can explain why I changed ic 7580 but channel 1a 4 is great from 5 to 16 ta as if gaining ta high there enters wheezing and there is no way to lower the channels
@@creativera2180 Good morning, I'm sorry, I must see you, I can change it because I have a show this week and I urgently need to resolve it. How can I help?
My problem lost audio on outputs (Mains) nothing at headphone jack can anyone give some advise just short of put my mixer in the thrash bucket Presonus support can't do nothing the mixer is too old for them to repair it
how do i fix my prenosus soundboard, it's been 5 years since i've had it stopped without sound, i'm from brazil if you're in instagram let us know please
Selamat siang, min. ... Saya dari blitar jawa timur, mempunyai presonus 16.4.2 sinyal output keluar tapi tidak ada bunyi yang dihasilkan bisa dibantu min... Terima kasih....
@@creativera2180 soalnya gini min, mixer saya kalo didiamkan 1 hari bunyi lagi, tp kalo saklar dimatikan terus dihidupkan lagi sudah tidak menghasilkan suara sama sekali, padahal led kontrol master ada sinyal...
Great'! it works as described. Be careful, the traces easyly going unstick with heat. Thanks Creative Ra
I will try to do this in my unit 16.4.2. Tnx
I have one that just went out 1-4 channels work the others nothing. Do you repair these mixers? I could send you mine! Thanks please let me know.
Hi, do you know were the phantom power supply is located inside the 16.4.2? Thanks
replace the voltage regulators with LM7805. had my 16.4.2 kept freezing up and sent it back to presonus for about $350 total a few years ago. said they replaced the board but they only replaced the voltage regulators with the same lame voltage regulators. 2 years later board freezes again, now prosonus says board out of service and wont fix it. found a guy to actually replace voltage regulators with beefier LM7805. so far no problems a few months in. good luck. dont have to toss a board where no parts can be salvaged. crazy design that they become disposable.
Hi! any leads for the Fat channel randomly changes values...? Thanks.
Hi...My Presonus 16.4.2 goes into Led meter overload and a loud sound in monitors after its been on a while, any clues ?
Hey! Thanks for the helpful videos! Where I can I buy this part from? The replacement channel strip 410-XMEN-FAD7-SP.
Cheers!
This very nice and educative, I have the presonus SL 16.4.2 The fire wire does not work. What should I do???
if the fire wire module is malfunction/damaged so far I have replaced it with a complete firewire module, because the factory only provides that part. and if later I can repair the module, I'll share it on my UA-cam channel.
Muy buen video, solo que tengo una consulta, no se si sea normal, pero compré una consola de estás usada y como a los 30 min activa se calienta mucho según mi punto de vista, y el dueño anterior dice que en ocasiones dejaba de mandar audio del Main, eso no me a pasado, pero en dado caso, cuál sería el problema y como saluvionarlo?. Si se necesita comprar un módulo completo en dónde lo podría encargar?.
De ante mano muchas gracias.
Yo la revise así superficialmente y lo que se calienta primero es la fuente de poder, pero no la revise a profundidad, solo fue superficial
Lo más importante es modificar la parte del regulador DC-DC del módulo DSP, reemplazándolo con el LM7805 IC (ver minutos de video 2:38 a 3:18). el sonido se pierde a veces no hay ninguna causa que el regulador de DC-DC sea inestable. ua-cam.com/video/5W9qCBr4LrY/v-deo.html
Hi, I have a SL 16.4.2, I will be buying the IC 7805 as per your recommendation.
But just before i buy, I just have a question and I hope to get an answer from you :)
I have a problem with AUX 1. The volume level is sometimes okay, but then after a few minutes the volume will suddenly drop a little bit, then go up again, then drop again..
Do you think i should also check or replace the pots inside AUX 1? Or the IC 7805 should fix the problem?
Thank you again for your content, I really appreciate your posts.
Problem about AUX you should also replace the capacitor 4.7uf 6.3V in the DSP module, there are 24 pcs. and If you have free time, it's better if you replace all the capacitors with metal bodies in the DSP Module. because if the use is over 5-6 years this capacitor will be damaged so that symptoms will appear abnormal symptoms in the master or Aux outputs
I don't have a video about replacing the capacitor DSP module for SL16.4.2,
if i have time i will make it later.
but an example of replacing the capacitor on the DSP Module can be seen on the SL 16.02 video here ua-cam.com/video/aGIYGXLOHgk/v-deo.html&t= 55s
@@creativera2180 Thank you I will wait if ever you get the chance to make that video! Would really appreciate it :) In the mean time ill install the IC 7805 for now
@@kelvincortez3283 in the DSP module there is a flexible cable that is connected to the LCD. be careful when disassembling this mixer, do not damage this cable
@@creativera2180 Hi again thank you :) Im disassembling the mixer now, all is going well, i just have a problem with the LCD ribbon/film strip cable, how did you pull it out? I dont want to use excessive force, but its tricky pulling it out
AMIGO TENGO UNA 16.0.2 Y SOLO SUENA EL CANAL 13/14 15/16 DONDE CREES QUE RADIQUE LA FALLA?
Buenas noches colega. Buen video. Le cuento que tengo una consola igual pero la falla que tengo es que no activa ningún phantom power. No se si me pueda ayudar. Gracias
El circuito de alimentación Phantom de 48 voltios está en la sección de la fuente de alimentación SMPS, puede haber un transistor defectuoso, llévelo a un distribuidor autorizado.
Spain
PreSonus Europe Limited
Unit 1 & 2 Cavan Enterprise Centre,
Dublin Road,
Killygarry,
Cavan,
Co Cavan,
www.presonus.com/buy/international-distributors
Buenas, tengo una 16.4.2 hace como 10 años. Los reguladores de FAT CHANNEL me rotan solo, no fisicamente, sino que en las ganancias, frecuencias, me suben o bajan solo ( por lo general tienden a bajar mas que a subir ), no solo una perilla, sino en casi todas. En general siento que están duras los reguladores rotativos ( creo que son encoders y no potenciometros ), se le puede echar lubricante tipo W40 ? Porque usé un limpiacontacto ecologico de contacmatics tipo CO2, pero no sirvieron para nada, me los endurece mas por el frio pero despues no me corrigen el problema. saludos !
I also have the SL 24.4 2 AI, it normally cuts out sound and .
This looks similar to my 16.0.2, and after replacing the voltage regulators, i was flabbergasted by the fact that the only connector that the BNC "lamp" connector's cord can reach, is a ground pin on the chassi. WHAT?
as chek R10 ohm 10 module I have to chek I can explain why I changed ic 7580 but channel 1a 4 is great from 5 to 16 ta as if gaining ta high there enters wheezing and there is no way to lower the channels
it is certain the cause of the damage is from the DSP module, I will try to find another part to replace the IC 7805. I'll let you know later
@@creativera2180 Good morning, I'm sorry, I must see you, I can change it because I have a show this week and I urgently need to resolve it. How can I help?
@@ruanpradobass the replacement for IC 7805 is NJM2845DL1
please buy, hope this solves your mixer's problem
My problem lost audio on outputs (Mains) nothing at headphone jack can anyone give some advise just short of put my mixer in the thrash bucket Presonus support can't do nothing the mixer is too old for them to repair it
how do i fix my prenosus soundboard, it's been 5 years since i've had it stopped without sound, i'm from brazil if you're in instagram let us know please
Apakah ini di indonesia?
Jika iya lokasi dimana ya?
alamat distributor & service resmi www.presonus.com/buy/international-distributors#AS
Selamat malam 🙏🙏
hallo selamat malam
Selamat siang, min. ...
Saya dari blitar jawa timur, mempunyai presonus 16.4.2 sinyal output keluar tapi tidak ada bunyi yang dihasilkan bisa dibantu min... Terima kasih....
Siang..
Biasanya modul firewire nya yg rusak
@@creativera2180 bisa kasih contoh gambar/foto yang perlu diganti min..
Terima kasih....
@@creativera2180 soalnya gini min, mixer saya kalo didiamkan 1 hari bunyi lagi, tp kalo saklar dimatikan terus dihidupkan lagi sudah tidak menghasilkan suara sama sekali, padahal led kontrol master ada sinyal...
@@didikagung2456 ada di video saya, udah aku kasih tutorial dan cara menggantinya.
cari aja judul How to replace firewire card SL16.4.2
@@creativera2180 Terima kasih min....
Hi
My presonus studio live 24.4.2 just please wait??
bang minta alamat dan nomor tlpnya