I am with you I like the angled sliders better than flat. Since I live in the land of salt in winter, I went with Greenland Rock Sliders and to save weight. I am not a rock crawler just a Hunter and Fisherman and I did get trail damage on my previous doors on my truck.
I went with the RCI slider`s as well as the full skid plate pkg. don`t regret it at all. super strong , angled doesn`t touch the rear door at the kickout. good video.
I went with RCI angled bump out sliders as well, and their full set of aluminum skids including gas tank skid. There's lots of good stuff out there, that's just what fit my bill at the time in 2018. If I did it again I might go with flat or less angled sliders just to have a little more foot room for getting to the roof. As is I have no more than the tube to stand on.
We've got the same sliders on our 2018 4Runner, we probably got them in 2019 I think. I was curious so I went and checked, we have a full inch of clearance from the bottom of the door to the top of the bump-out. Great video and great sliders. Maybe not any more, but when we bought, if you were a little industrious, it wasn't too hard to find a $100 off coupon from RSG either. Good folks.
I have the RSG sliders that are flat. Much easier to access the roof. My only issue with the badge is that the rivets start to discolor/corrode after a while at the edges of the badge. They are extremely strong. I had a car hit me broadside, half on the sliders and half on the front wheel. The 4Runner was totaled, but I took the sliders off and installed them on my new 4Runner without any issue. A little black touch up paint and they were good as new.
I have the flat one with kick out and grip top plate.. i dont rock crawl and i love them for general protection in light off roads and for roof access. Very strong build quality ! Rock solid. I saw 2 of the rivets on the badge starting to discolor, think I'll replace them with stainless before the snow flies where I am.
I purchased the RSG 0-deg w/kickout after watching y'alls channel and love them on my 4runner. Also bought Toytec suspension lift. Keep the videos coming
Wasn't thinking about the rear door hitting the bump out, but glad you mentioned it. I've got a set on order from Westcott but they're the 0º kickout, not the 20º version. I wanted them to be both, sliders and steps.
I ordered a set of shrockworks, unfortunately the company went under and ran off with my money without sending the product. I was looking at the RSG but wasn't totally feeling the product, similar to what you mention about the badge. I ended up getting the RCI sliders and I am very happy that it worked out this way, I think the RCI sliders are the nicest thing I have installed on the truck.
I have the RCI angled with bump out and I have about 3/4” clearance. The top plate on mine is welded on and their logo is in the plate. Where I live rust is an issue and they now offer a model with a removable top plate which would make removing rust and touching up much easier.
Thanks for the video! I have the exact same angled sliders that I installed last year. I have 5/8 inch of a gap right now (but I haven't used them as extensively as you have) maybe they will bend up over time. I thought when I installed them there was a bit of wiggle room to drop them down a couple 1/8s of an inch due to the size of the mounting holes, but I would have to remove a bolt to verify.
I’ve got the same RSG’s and they have worked well. I haven’t had the door hit yet. I did take one hit behind the front wheel in front of the slider that did impact the bottom fender mount but I think the slider kept it from being worse.
Bent my rock sliders on the driver side when offroading the DBBB in Kentucky a few weekends ago. They're angled and my rear driver side door rubs on it. So Probably try to hammer it back down a bit.
@WanderlostOverland Do you think the bump out provides more functionality? I picture them protecting the sidewall of my rear tires when taking hard turns through obstacles. I wonder if they would wind up pushing me off my line though. Any opinion?
I have CBI flat sliders and I love them (in my opinion they're the best looking sliders made). I wanted flat, because they are used for getting kids in and out of the vehicle. I understand wanting the angled sliders, but I find flat more functional overall. Are your RSG sliders rolled or DOM? DOM would be more resilient to bending up towards the door.
I must be watching the wrong rock slider videos or perhaps I'm too critical. Can you show us how your rock sliders got bent up, functionally what is happening, where is the damage? Are they practical for every day use, for access to the roof, for kids, for keeping dirt out of the cabin? The comments about looks, why?
Not a rock crawler..so the flat work great for us and easy to step up… Never get the rhino liners..dirt stains -can never be clean…I use black spray paint every time…
We have the RSG flat kick-outs and are 100% happy. They stand up to everything we throw at them.
Sliders a must in my opinion for even moderate off-roading. Great video as usual!
Thanks! 👍
I went with the flat version. Going on 5 yrs. Love and recommend them!!!
I am with you I like the angled sliders better than flat. Since I live in the land of salt in winter, I went with Greenland Rock Sliders and to save weight. I am not a rock crawler just a Hunter and Fisherman and I did get trail damage on my previous doors on my truck.
How are you like by the greenlane angled sliders. I’m curious if there’s much foot space on the sliders near the front door
@@KyleHammerquist155
Yes you can step on it if you need too as my wife does getting in the front. I’m 6’2 and I just step in and don’t use them.
I went with the RCI slider`s as well as the full skid plate pkg. don`t regret it at all. super strong , angled doesn`t touch the rear door at the kickout. good video.
I went with RCI angled bump out sliders as well, and their full set of aluminum skids including gas tank skid. There's lots of good stuff out there, that's just what fit my bill at the time in 2018.
If I did it again I might go with flat or less angled sliders just to have a little more foot room for getting to the roof. As is I have no more than the tube to stand on.
We've got the same sliders on our 2018 4Runner, we probably got them in 2019 I think. I was curious so I went and checked, we have a full inch of clearance from the bottom of the door to the top of the bump-out. Great video and great sliders. Maybe not any more, but when we bought, if you were a little industrious, it wasn't too hard to find a $100 off coupon from RSG either. Good folks.
This is a great series. For me this is way more informative than all those unpacking/install stuff. Kudos
More to come!
I went with flat sliders with kickout for the reason you mentioned, clearance eventually.
I have the RSG sliders that are flat. Much easier to access the roof. My only issue with the badge is that the rivets start to discolor/corrode after a while at the edges of the badge. They are extremely strong. I had a car hit me broadside, half on the sliders and half on the front wheel. The 4Runner was totaled, but I took the sliders off and installed them on my new 4Runner without any issue. A little black touch up paint and they were good as new.
I have the flat one with kick out and grip top plate.. i dont rock crawl and i love them for general protection in light off roads and for roof access. Very strong build quality ! Rock solid. I saw 2 of the rivets on the badge starting to discolor, think I'll replace them with stainless before the snow flies where I am.
I purchased the RSG 0-deg w/kickout after watching y'alls channel and love them on my 4runner. Also bought Toytec suspension lift. Keep the videos coming
Great to hear!
Wasn't thinking about the rear door hitting the bump out, but glad you mentioned it. I've got a set on order from Westcott but they're the 0º kickout, not the 20º version. I wanted them to be both, sliders and steps.
I ordered a set of shrockworks, unfortunately the company went under and ran off with my money without sending the product. I was looking at the RSG but wasn't totally feeling the product, similar to what you mention about the badge. I ended up getting the RCI sliders and I am very happy that it worked out this way, I think the RCI sliders are the nicest thing I have installed on the truck.
I have the RCI angled with bump out and I have about 3/4” clearance.
The top plate on mine is welded on and their logo is in the plate. Where I live rust is an issue and they now offer a model with a removable top plate which would make removing rust and touching up much easier.
Thanks for the video! I have the exact same angled sliders that I installed last year. I have 5/8 inch of a gap right now (but I haven't used them as extensively as you have) maybe they will bend up over time. I thought when I installed them there was a bit of wiggle room to drop them down a couple 1/8s of an inch due to the size of the mounting holes, but I would have to remove a bolt to verify.
I got the flat. They are great.
I’ve got the same RSG’s and they have worked well. I haven’t had the door hit yet. I did take one hit behind the front wheel in front of the slider that did impact the bottom fender mount but I think the slider kept it from being worse.
Bent my rock sliders on the driver side when offroading the DBBB in Kentucky a few weekends ago. They're angled and my rear driver side door rubs on it. So Probably try to hammer it back down a bit.
Also I plan to get these I just have to decide on a bumper and winch first.
Well they heard you or something because the ones I just ordered have the rsg cut into the steel
@WanderlostOverland Do you think the bump out provides more functionality? I picture them protecting the sidewall of my rear tires when taking hard turns through obstacles. I wonder if they would wind up pushing me off my line though. Any opinion?
I have CBI flat sliders and I love them (in my opinion they're the best looking sliders made). I wanted flat, because they are used for getting kids in and out of the vehicle. I understand wanting the angled sliders, but I find flat more functional overall. Are your RSG sliders rolled or DOM? DOM would be more resilient to bending up towards the door.
DOM, we just abuse them.
Have you ever looked at aftermarket wheel well fenders? All looks of course. Just curious
I have the same rock sliders without top plate. Mine are not the close to the rear door. Must have been bent from rocks or they changed the angle.
What is the practical difference between weld on rock sliders and bolt on rock slider? Is there a nominal difference?
The weld on are probably stronger at the frame, but you'd have one heck of time taking them off to repaint or straighten.
I must be watching the wrong rock slider videos or perhaps I'm too critical. Can you show us how your rock sliders got bent up, functionally what is happening, where is the damage? Are they practical for every day use, for access to the roof, for kids, for keeping dirt out of the cabin?
The comments about looks, why?
have you tried to loosen all the bolts and retighten at its lowest position?
Yes, but the first time we lean against a rock it goes right back.
What is the angle? 20 degrees?
What is the diameter of the steel pipes used?
How are you liking the Ridge Grapplers? I’m debating between those and the MT Baja Boss a/t.
The Ridge Grapplers are great for our application.
@@WanderlostOverland thanks for the reply.
What is the degree of angle?
Any word from RSG if they’ll be making a change?
Nope
Can you confirm you got the DOM version? Curious given the rear door issue.
I have the DOM angled version with the kick out. 3 years of hard Colorado wheeling and plenty of bonks. No issues for me.
I would remove the badge at install any way.
Not a rock crawler..so the flat work great for us and easy to step up…
Never get the rhino liners..dirt stains -can never be clean…I use black spray paint every time…
Check your frame I bet its bent up Toyota uses thin steel like sheet metal
Why don't you crimp the top of the kick out yourself? Problem solved.
Could side steps double as sliders if they sat high up like sliders do?
No, Typical side steps are not nearly strong enough to hold up.
@@WanderlostOverland copy