My tailstock was binding so bad so I decided to take it apart. I couldn't figure out how to take that retainer ring out and there was a set screw on it. This video just saved my butt for sure. Thank you!
Thanks Gord. I had noticed the tailstock on my DVR tightening up, and today it just became unbearable while drilling out a box. I remembered this video from whenever and was able to find it readily. Very clear instructions, and as I have the same lathe (still grey, of course) it was real quick and easy, problem solved. Thanks for posting this.
Thanks for the video. I just cleaned mine and was surprised at the amount of gunk inside. I used a dry lubricate in hopes that it will not attract dust. In most cases WD40 is my first choice.
I’m happy if the video helped or motivated you to maintain your tailstock. In my newest video I showed what I ended up using instead of WD-40. I’m very happy with it and must remember to clean and lubricate on a regular basis. Thank you for watching, Dan! 😃😃 Take care, .....Gord
Woodbees Gord there is a dry lub ' that I use on my lath every where it is needed. It goes on wet and dries in a few minutes. It won't attract any dust. I get it at Lowes. great job teaching in your vids
I have the DVR xp and about a year ago upgraded to the NOVA DVR XP CONTROL PANEL UPGRADE (SKU 55523). It does everything your current panel does and had some more features including a speed control knob. At first, not sure I was going to use the new features much but the more I use it the more I use them. Really enjoy your videos. Learn a lot and enjoy a little humor.
I have a Nova Galaxi lathe and the tail stock froze up recently. Along with cleaning the areas you did, I had to clean and hone the tail stock bore and outside of the quill. Apparently dust from turning wet wood had gotten between the quill and bore causing fine deposits of rust. I lubed the threads with WD 40 and the bore with graphite powder. I am paying attention to how much effort it takes to operate the handwheel. Thanks for all the great videos.
Thank you, Bram. I must do a better job of maintaining my equipment so I don’t HAVE to maintain my equipment! Thank you for watching! Take care, .....Gord
Excellent informative video Gord, and I agree on using WD-40 as that is what I use! I do not have a Nova DVR but I have a Nova 16-24 lathe and when I bought it a online friend who also owned a Nova recommended to put some duct tape over the slot at the back of the lathe to help keep the dust out of the tailstock. I did that and it sure helps but after about 10 years I think that I may have to take mine apart as it seems to be getting harder to turn and after this video it should be quite easy...…..I hope!!!1 Cheers Al
Thank you, Mike. I didn’t really find it intimidating but it took me a few minutes to figure out how to take it apart. After that it was fairly easy. Now I have to remember to do it frequently and to try some of the other lubricants that have been suggested. Hope you’re doing well, Mike. Take care, .....Gord
I can’t believe I waited so long to do it, Mike! I have put a reminder on my phone to make sure that I do it at least every couple of months. Don’t want to let it get that way again. Take care my friend, .....Gord
Hello Gord, Another very useful video, especially so because I also have a Nova DVR XP lathe. Your videos are always helpful. Thank you. A similar video on servicing the banjo would also be helpful, in case I’ve missed something. By the way, I shorted out my motherboard following a buffing session with my Beale system. There’s only one center in the US for repairing a Nova DVR Xp, in St. Petersburg FL, and I’m in California. Nevertheless, they were helpful Although their images didn’t match my photos, I was able to reassemble my lathe and it’s working fine again. Thanks again, Gord.
I’m happy that you like the videos, Kenneth! Thank you for watching them; I appreciate the support very much. To tell you the truth I have never looked closely at my banjo. It’s never given me a problem and I’m glad you mentioned it because I think it’s a very good idea to look at it before it does cause trouble. I guess I’m guilty of ignoring things until I’m forced to take care of them. Bad Gord!! 😁 I also had a motherboard burn out a few years ago and while I didn’t have a problem replacing it - retired electrician - I was surprised at how expensive it was! Did I mention that I’m cheap? 🤣🤣 Thanks again for mentioning the banjo! I will take a look at mine tomorrow. I’m not sure it would be worth a video but I will certainly check it out! Take care, .....Gord
Gord, I also have a DVR XP, and had the same issue last year with a sticking tail stock. If I may suggest, do a follow up video showing how to clean the gunk off the bottom plate of the tail stock, and if you are adventurous, show how to align the tail stock with the head stock.
Doug, I don’t have any “gunk” on the bottom of my tailstock. Maybe I’m just lucky but that’s never been a problem for me. As far as aligning the tailstock, there is a bit of play in my tailstock as it rides on the bed ways. It’s very minor but still the only thing on the lathe that I’m not totally happy with. I’ve been told that the newer ones don’t have that problem. It’s something that I have learned to deal with but I don’t think I would be able to properly explain how to align it with mine not performing perfectly. Thanks for watching and for your input. Take care, .....Gord
I’m not sure if it’s a good thing or not but my wife likes to help clean up the shop. Of course once she finishes I can’t find anything for a few days but I’m not brave enough to tell SWMBO not to help! 😳😳😳😳 Take care my friend, .....Gord
wd is good but ether of these 2 are better WD-40® SPECIALIST® PROTECTIVE WHITE LITHIUM GREASE WD-40® SPECIALIST® DIRT & DUST RESISTANT DRY LUBE PTFE SPRAY the dry lube is what i use
Gord, I agree with Kevin. WD-40 was never designed as a lubricant -- the "WD" stands for Water Displacement. Formula number 40, to be complete :-) I too use a dry lube with Teflon, a 3M product (don't remember the name, it's down in the shop, & I'm lazy...) that I first started using to lubricate motorcycle chains. Now it's my go to lubricant. Clyde
My tailstock was binding so bad so I decided to take it apart. I couldn't figure out how to take that retainer ring out and there was a set screw on it. This video just saved my butt for sure. Thank you!
My pleasure, Casey. I’m glad I was able to help. I appreciate you watching my video!
Happy turning,
…..Gord
Thanks Gord. I had noticed the tailstock on my DVR tightening up, and today it just became unbearable while drilling out a box. I remembered this video from whenever and was able to find it readily. Very clear instructions, and as I have the same lathe (still grey, of course) it was real quick and easy, problem solved. Thanks for posting this.
My pleasure, Chris. I’m always happy to help if I can. 😃👍🇨🇦
Thanks for the video. I just cleaned mine and was surprised at the amount of gunk inside. I used a dry lubricate in hopes that it will not attract dust. In most cases WD40 is my first choice.
I’m happy if the video helped or motivated you to maintain your tailstock. In my newest video I showed what I ended up using instead of WD-40. I’m very happy with it and must remember to clean and lubricate on a regular basis.
Thank you for watching, Dan! 😃😃
Take care,
.....Gord
My pleasure.
Woodbees Gord there is a dry lub ' that I use on my lath every where it is needed. It goes on wet and dries in a few minutes. It won't attract any dust. I get it at Lowes. great job teaching in your vids
That sounds ideal, Randy! Can you tell me what it’s called? Thanks for watching!
.....Gord
Gord, The name of the lubricant is B'LASTER, A silicone base with Teflon. It's made in Cleveland, Ohio. I think it is a real good product.
Thank you, Randy! I will see if it’s available in Canada.
Take care,
.....Gord
I have the DVR xp and about a year ago upgraded to the NOVA DVR XP CONTROL PANEL UPGRADE (SKU 55523). It does everything your current panel does and had some more features including a speed control knob. At first, not sure I was going to use the new features much but the more I use it the more I use them. Really enjoy your videos. Learn a lot and enjoy a little humor.
Thank you, John. I’m happy that you like the videos. Thanks for the tip about the panel upgrade. I will have to check that out! 😎
Take care,
.....Gord
I have a Nova Galaxi lathe and the tail stock froze up recently. Along with cleaning the areas you did, I had to clean and hone the tail stock bore and outside of the quill. Apparently dust from turning wet wood had gotten between the quill and bore causing fine deposits of rust. I lubed the threads with WD 40 and the bore with graphite powder. I am paying attention to how much effort it takes to operate the handwheel. Thanks for all the great videos.
That sounds like a lot of work, Pat. Glad you were able to get it working again! Thanks for watching!
Take care,
.....Gord
Good advice Gord ! not surprising the amount of rubbish that gets into works... fine dust etc . A little love pays dividends :)
Cheers, Bram
Thank you, Bram. I must do a better job of maintaining my equipment so I don’t HAVE to maintain my equipment! Thank you for watching!
Take care,
.....Gord
Great tip Gord keep them coming. I was leary to try but I have the same lathe, so thanks again
My pleasure, Brent. I hope it helps!
Take care,
…..Gord
Excellent informative video Gord, and I agree on using WD-40 as that is what I use! I do not have a Nova DVR but I have a Nova 16-24 lathe and when I bought it a online friend who also owned a Nova recommended to put some duct tape over the slot at the back of the lathe to help keep the dust out of the tailstock. I did that and it sure helps but after about 10 years I think that I may have to take mine apart as it seems to be getting harder to turn and after this video it should be quite easy...…..I hope!!!1
Cheers Al
I hope it’s easy to clean and lubricate, Al. It shouldn’t be difficult.
Happy New Year!🥂🥂🥂🥂
.....Gord
If you can find some spray on graphite, it works quite well. Dust doesn't stick to it because it is not oily.
Good information. Thank you for the input!
Good reminder and tutorial, Gord! Now I know what I will be doing this afternoon!
Phil
Thank you very much, Phil. Glad you liked it. Thanks for watching!
.....Gord
Good video, Gord. It is a bit intimidating the first time you remove the quill but not that difficult and they all need cleaning periodically.
Thank you, Mike. I didn’t really find it intimidating but it took me a few minutes to figure out how to take it apart. After that it was fairly easy. Now I have to remember to do it frequently and to try some of the other lubricants that have been suggested. Hope you’re doing well, Mike.
Take care,
.....Gord
Great video Gord, when I did this on my old lathe I was amazed at the difference.
Cheers
Mike
I can’t believe I waited so long to do it, Mike! I have put a reminder on my phone to make sure that I do it at least every couple of months. Don’t want to let it get that way again.
Take care my friend,
.....Gord
Hello Gord,
Another very useful video, especially so because I also have a Nova DVR XP lathe. Your videos are always helpful. Thank you. A similar video on servicing the banjo would also be helpful, in case I’ve missed something. By the way, I shorted out my motherboard following a buffing session with my Beale system. There’s only one center in the US for repairing a Nova DVR Xp, in St. Petersburg FL, and I’m in California. Nevertheless, they were helpful Although their images didn’t match my photos, I was able to reassemble my lathe and it’s working fine again. Thanks again, Gord.
I’m happy that you like the videos, Kenneth! Thank you for watching them; I appreciate the support very much.
To tell you the truth I have never looked closely at my banjo. It’s never given me a problem and I’m glad you mentioned it because I think it’s a very good idea to look at it before it does cause trouble. I guess I’m guilty of ignoring things until I’m forced to take care of them. Bad Gord!! 😁
I also had a motherboard burn out a few years ago and while I didn’t have a problem replacing it - retired electrician - I was surprised at how expensive it was! Did I mention that I’m cheap? 🤣🤣
Thanks again for mentioning the banjo! I will take a look at mine tomorrow. I’m not sure it would be worth a video but I will certainly check it out!
Take care,
.....Gord
Great video thank you.
Thank you very much, Mike!
.....Gord
Thanks for sharing
You are very welcome, Tim. Thank you for watching!! I appreciate the support.
…..Gord
Hey Gord ... I enjoy your videos, thanks for the heads up on the maintenance tip....Tim
My pleasure, Tim. Thanks for watching! I hope it helps.
.....Gord
Good video, Gord!
Thank you very much, Rick!
Gord, I also have a DVR XP, and had the same issue last year with a sticking tail stock. If I may suggest, do a follow up video showing how to clean the gunk off the bottom plate of the tail stock, and if you are adventurous, show how to align the tail stock with the head stock.
Doug, I don’t have any “gunk” on the bottom of my tailstock. Maybe I’m just lucky but that’s never been a problem for me. As far as aligning the tailstock, there is a bit of play in my tailstock as it rides on the bed ways. It’s very minor but still the only thing on the lathe that I’m not totally happy with. I’ve been told that the newer ones don’t have that problem. It’s something that I have learned to deal with but I don’t think I would be able to properly explain how to align it with mine not performing perfectly.
Thanks for watching and for your input.
Take care,
.....Gord
Try a dry PTFE spray !
Thank you for the tip!!
I check everything during the winter,can't convince wifey to pick up the spanners!🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣👍👍👍👍👍👍
I’m not sure if it’s a good thing or not but my wife likes to help clean up the shop. Of course once she finishes I can’t find anything for a few days but I’m not brave enough to tell SWMBO not to help! 😳😳😳😳
Take care my friend,
.....Gord
Good info to know...
I hope it’s helpful, Carol!
Hmm, I really need to spend an afternoon to do the head and tailstock. They’re both squeaky.
Don’t you just hate that!! 😠😠
A ver si me mandas un pegatina tuya
I would be happy to send you a sticker! What is your mailing address?
I will put the sticker in the mail tomorrow. Do you have one to send me?
@@GordonRock1 no no tengo pero te mandare una pegatina de la bandera de España asi sabras que soy yo 😂😂😂😂😂muchas gracias
wd is good but ether of these 2 are better WD-40® SPECIALIST® PROTECTIVE WHITE LITHIUM GREASE WD-40® SPECIALIST® DIRT & DUST RESISTANT DRY LUBE PTFE SPRAY the dry lube is what i use
I appreciate the tip, Kevin. Thank you! I will check out that dry lube! Thanks for watching!
Take care,
.....Gord
Gord, I agree with Kevin. WD-40 was never designed as a lubricant -- the "WD" stands for Water Displacement. Formula number 40, to be complete :-) I too use a dry lube with Teflon, a 3M product (don't remember the name, it's down in the shop, & I'm lazy...) that I first started using to lubricate motorcycle chains. Now it's my go to lubricant. Clyde
Thank you for the input, Clyde! 👍
Clyde Ulmer, can this product can be purchased at an automotive store?
not sure if you are in the usa just google were to buy wd 40