You could see in the beginning that Becca looked extremely aggravated that it wasn't an easy install, but as usual, you guys knocked it out and made it look good.
Nothing worth doing is easy, so with any luck it’ll be worth it in the end. It’s a pretty slick set up and only took a few extra step to get installed.
I was a tad stressed when that plastic line broke haha. I also didn’t record the part where we dropped a socket down into my alternator bracket and had to fish it out
I have a 2015 jk sport and installed this product . Had to trim some plastic from intake manifold ,but no hose cutting. Tight fit installing Schrader valve elbow ,but be patient it can be done .
When the engine is first started after the installation, he should have used "clear flood mode" to crank engine to build oil pressure before engine starts.
didnt have any of these problems putting mine in... seems like user error here. also would recommend flooding the filter by pushing down on the gas while cranking the engine for atleast 5 seconds then starting it, it will help reduce chatter on initial start up where the oil filter is empty ie: when you replace it with a new filter. im a big fan of this mod really helps quite down the chatter on cold start especially up here in alaska
Thanks for the video! At the 6:25 mark, for the rigid, aluminum cored fuel vapor hose, did you attach it to the rubber hose with a compression fitting? If so, any chance you can tell us the size of the fittings, as well as the inside and outside diameters of each of the lengths of hoses you used? I have a 2015 JKU and those lines are in exactly the same place and am fearful they will crack off if I do this mod. Would rather be ready in advance with what I need to deal with it….
@yellerlife nice, I'm interested in this product for my 2.7 ecoboost, but haven't seen any real-world results. Just installs. I wish someone had shown the before and after with an oil pressure gauge.
PSA: I just installed this on my Jeep and you ABSOLUTELY DO NOT have to cut the 2 vacuum lines (they're not fuel lines as she misspoke in the video at one point) on the JK 2012-1018 3.6L Pentastar. You can unplug them and gently pry them out of the way while installing the Baxter unit and then installing the filter. Not trying to be rude, but I just want to make people aware. I'm not a fan of chopping stuff on my cars and making something irreversible. The worst part of this install is screwing in the elbow for the schrader valve on the side (all of my 15/16" wrenches wouldn't fit it, so I had to do it with a small crescent wrench). Also make sure you prime the oil system by doing the "clear flood mode" crank. The dry start "chatter" that was barely there on my 2014 JKU is now gone. In my opinion, this mod is well worth it, if nothing else for the better filtration and ease of oil filter change. And no, I'm not affiliated with Baxter, just impressed by this product.
You definitely do need to replace the hoses on some models. My wrangler is just like theirs and the adapter absolutely does not fit with the current PCV hoses. They run directly across where the adapter fits. I have to completely replace the hoses in order to install my adapter.
Start taking stuff apart. Anything, stuff that you were going to just toss in the trash and try to put it back together. Half of my skills are having confidence in pulling something apart and knowing I can get it back together.
Absolutely! I am hoping to put stickers on my website soon. Would you prefer that logo as a white decal, or an actual sticker with white logo and black background?
@@Thaddeus.N haven’t done an old change since install. The Jeep get so few miles we do an oil change as our spring maintenance. It has an air line port for purging the filter before removal
It’s basically that easy, we ran into afew lines that were in the way. Super easy to work around and I’d bet you could have left them, would just make spinning on a new filter a tight squeeze
Yeah basically. It’s super simple. Just gotta tighten everything down correctly and get your air valve positioned in the right place so you can access it for future oil changes. If the hoses were not a problem, it would have been installed in less than an hour with an oil change.
Never ever get under a car that is only supported by the jack. There was not a jack stand in sight. I would hate to see anything happen to you . Just an old guy that has seen way to much that could have been prevented.
We were just talking about it yesterday, her Jeep sits for days at a time and hasn’t had any long cranks since the install. Is it because of the filter specifically I can’t say but that’s all that changed recently. At this point I’d say it was worth it.
@@yellerfab do you hear any rattling at startup? The adapter is advertised as being able to eliminate the rattle by providing oil to the top end almost instantly. I installed one of these on my jeep a week ago, and I’ve had mixed things happen since putting it on. Sometimes it eliminates the rattle completely, and other times it doesn’t.
I've still yet to see any actual data that these effectively do anything? ... seems like mostly Baxter Marketing. All modern oils have additives to protect components during start up. The rattle you are hearing, again as I understand, is the hydraulic chain tensioner. Again I would like to hear from an actual motor expert if these are indeed providing a benefit or simply more snake oil.
@@obrianmcc I don’t disagree, I know the factory housing is garbage and is a known problem regardless so it’s worth it for the spin on filter upgrade as far as I’m concerned. If it does any thing more it’s just a bonus to me
@@tdz69 nope, if you have a Jeep jk it’s worth its weight in gold. No long crank at start up even after a month of sitting is enough for me to say it’s doing something that mopar couldn’t solve. It has nothing to do with oil change intervals. Mopar like all of the other major oem build junk that only kinda works.
No need to. Product is fine, and Jeep is fine, just needed to add a few extra steps. Made it more user friendly in the end. And you’d be surprised how easy it is to put up with complaining, just post a UA-cam video and wait for some comments haha
@yellerfab zero desire to do so. I'm just saying that I enjoyed your video with the exception of what I mentioned. The one problem was self inflicted. I am really good at doing that myself.
@@scottnugent4791 It’s all part of the game. At this point I look forward to the punishment. As Red Forman would say, “you don’t have bad luck, the reason bad things happen to you is because your a dumba$$”
@krisk1547 that’s why it has the schrader valve that comes with it. Pump a few psi of air in through that for a few seconds and it evacuates all of the oil from the filter. You then unscrew it and you won’t spill a drop.
@@resolutejkuShop air is not sterile, but it is fairly clean. Air tools would not tolerate dirty air. How would the shop air get dirty? Most compressors have an air intake filter. My concern is the usual shop air pressure.
@@patrickderubis4527 kinda seems like a lot of time to have no oil pressure. But I have heard metal doesnt wear out until it sees 6 second of no oil haha
@@patrickderubis4527 well that’s cool but it does so don’t put one on your Jeep I don’t care. Easy business for guys like me who have to replace stuff that doesn’t exist to guys like you.
You could see in the beginning that Becca looked extremely aggravated that it wasn't an easy install, but as usual, you guys knocked it out and made it look good.
Nothing worth doing is easy, so with any luck it’ll be worth it in the end. It’s a pretty slick set up and only took a few extra step to get installed.
I was a tad stressed when that plastic line broke haha. I also didn’t record the part where we dropped a socket down into my alternator bracket and had to fish it out
I have a 2015 jk sport and installed this product . Had to trim some plastic from intake manifold ,but no hose cutting. Tight fit installing Schrader valve elbow ,but be patient it can be done .
When the engine is first started after the installation, he should have used "clear flood mode" to crank engine to build oil pressure before engine starts.
Thanks. I am going to do the same with my 2015.
didnt have any of these problems putting mine in... seems like user error here. also would recommend flooding the filter by pushing down on the gas while cranking the engine for atleast 5 seconds then starting it, it will help reduce chatter on initial start up where the oil filter is empty ie: when you replace it with a new filter.
im a big fan of this mod really helps quite down the chatter on cold start especially up here in alaska
@@ralphjlmartinez different years and models have different lines, super common, super easy fix
Thanks for the video! At the 6:25 mark, for the rigid, aluminum cored fuel vapor hose, did you attach it to the rubber hose with a compression fitting? If so, any chance you can tell us the size of the fittings, as well as the inside and outside diameters of each of the lengths of hoses you used? I have a 2015 JKU and those lines are in exactly the same place and am fearful they will crack off if I do this mod. Would rather be ready in advance with what I need to deal with it….
I will try and update everyone after a little bit of time to let you all know if it did cure my dry starts
Your so wrong, my buddies cousins uncle did a ls swap for the cost of a case of busssh and a weekend even has cold ac haha
So... did it work?
@@NITROUSnBIASPLYS haven’t had a dry start since! So I guess so far so good! I should probably make an update video
@yellerlife nice, I'm interested in this product for my 2.7 ecoboost, but haven't seen any real-world results. Just installs. I wish someone had shown the before and after with an oil pressure gauge.
PSA: I just installed this on my Jeep and you ABSOLUTELY DO NOT have to cut the 2 vacuum lines (they're not fuel lines as she misspoke in the video at one point) on the JK 2012-1018 3.6L Pentastar. You can unplug them and gently pry them out of the way while installing the Baxter unit and then installing the filter. Not trying to be rude, but I just want to make people aware. I'm not a fan of chopping stuff on my cars and making something irreversible. The worst part of this install is screwing in the elbow for the schrader valve on the side (all of my 15/16" wrenches wouldn't fit it, so I had to do it with a small crescent wrench). Also make sure you prime the oil system by doing the "clear flood mode" crank. The dry start "chatter" that was barely there on my 2014 JKU is now gone. In my opinion, this mod is well worth it, if nothing else for the better filtration and ease of oil filter change. And no, I'm not affiliated with Baxter, just impressed by this product.
You definitely do need to replace the hoses on some models. My wrangler is just like theirs and the adapter absolutely does not fit with the current PCV hoses. They run directly across where the adapter fits. I have to completely replace the hoses in order to install my adapter.
Nick is so cool. I wish I was good at engineering things.
Start taking stuff apart. Anything, stuff that you were going to just toss in the trash and try to put it back together. Half of my skills are having confidence in pulling something apart and knowing I can get it back together.
Love your content.
Any chance we could get the Yeller Fab logo of the golden retriever with the welder as a sticker?
Absolutely! I am hoping to put stickers on my website soon. Would you prefer that logo as a white decal, or an actual sticker with white logo and black background?
@@yellerlife I could go for either one.
@@justinbuehrig3405ok. Well it’s in the works! I think I want to do sticker, so I need to order a few more of my designs in before I list them
I have a 2014, I hope I dont have to cut any lines after I order this filter adapter.
Just be gentle taking the hoses off, but if it does brake it’s an easy fix.
Got one for my 18 JL.. just came in the mail 2 days ago. No to install this weekend
Nice, might want to watch a few peoples install videos and see if you need to relocate anything like we did.
Does the oil filter dump oil all over the engine now when you unscrew it?
@@Thaddeus.N haven’t done an old change since install. The Jeep get so few miles we do an oil change as our spring maintenance. It has an air line port for purging the filter before removal
First remove the oil fill cap, then apply 30 psi to the schrader valve on the Baxter adapter to purge the oil from the filter before unscrewing it.
Besides the hoses .do u just unscrew the oem oil filter cap and remove the filter and screw in the Baxter ?
It’s basically that easy, we ran into afew lines that were in the way. Super easy to work around and I’d bet you could have left them, would just make spinning on a new filter a tight squeeze
Yeah basically. It’s super simple. Just gotta tighten everything down correctly and get your air valve positioned in the right place so you can access it for future oil changes. If the hoses were not a problem, it would have been installed in less than an hour with an oil change.
Did the engine cover fit back in with the new filter?
Can’t say we’ve ran the cover in years. I’m not even sure we still have it haha
Was wondering about this thing.
Never ever get under a car that is only supported by the jack. There was not a jack stand in sight. I would hate to see anything happen to you . Just an old guy that has seen way to much that could have been prevented.
I CANT BELIEVE IT'S 4 HUNDRED DOLLARS HOLY SHIT
Any update? How’s it work for you?
We were just talking about it yesterday, her Jeep sits for days at a time and hasn’t had any long cranks since the install. Is it because of the filter specifically I can’t say but that’s all that changed recently. At this point I’d say it was worth it.
@@yellerfab do you hear any rattling at startup? The adapter is advertised as being able to eliminate the rattle by providing oil to the top end almost instantly. I installed one of these on my jeep a week ago, and I’ve had mixed things happen since putting it on. Sometimes it eliminates the rattle completely, and other times it doesn’t.
I've still yet to see any actual data that these effectively do anything? ... seems like mostly Baxter Marketing. All modern oils have additives to protect components during start up. The rattle you are hearing, again as I understand, is the hydraulic chain tensioner. Again I would like to hear from an actual motor expert if these are indeed providing a benefit or simply more snake oil.
@@obrianmcc I don’t disagree, I know the factory housing is garbage and is a known problem regardless so it’s worth it for the spin on filter upgrade as far as I’m concerned. If it does any thing more it’s just a bonus to me
Agreed. Waste of money for the most part. Like the catch cans on non gdi engines. Just keep up with regular oil changes and drive the jeep.
@@tdz69 nope, if you have a Jeep jk it’s worth its weight in gold. No long crank at start up even after a month of sitting is enough for me to say it’s doing something that mopar couldn’t solve. It has nothing to do with oil change intervals. Mopar like all of the other major oem build junk that only kinda works.
POS jeep use to be good
Did you contact Baxter? Your complaining got old quickly
No need to. Product is fine, and Jeep is fine, just needed to add a few extra steps. Made it more user friendly in the end. And you’d be surprised how easy it is to put up with complaining, just post a UA-cam video and wait for some comments haha
@yellerfab zero desire to do so. I'm just saying that I enjoyed your video with the exception of what I mentioned. The one problem was self inflicted. I am really good at doing that myself.
@@scottnugent4791 half the fun is figuring out how to undig the hole you make haha
@@yellerfab 90% of my time is fixing my screw ups. Laughing at myself is therapeutic!
@@scottnugent4791 It’s all part of the game. At this point I look forward to the punishment. As Red Forman would say, “you don’t have bad luck, the reason bad things happen to you is because your a dumba$$”
Removing it without making a mess will be a problem.
It has a valve for applying compressed air to remove any oil in the system. It's a pretty slick setup and have been strongly considering it.
@krisk1547 that’s why it has the schrader valve that comes with it. Pump a few psi of air in through that for a few seconds and it evacuates all of the oil from the filter. You then unscrew it and you won’t spill a drop.
@@doccameleon7565I agree that it’s a slick setup but how clean is shop air? No risk of blowing debris back in your oil housing?
@@resolutejkuShop air is not sterile, but it is fairly clean. Air tools would not tolerate dirty air. How would the shop air get dirty? Most compressors have an air intake filter. My concern is the usual shop air pressure.
Scam
@@patrickderubis4527 How do you figure?
@@yellerfab Less then 3 to 5 seconds until you have 30lbs. of pressure.
@@patrickderubis4527 kinda seems like a lot of time to have no oil pressure. But I have heard metal doesnt wear out until it sees 6 second of no oil haha
@@yellerfab NO such thing as dry start. You don't know how an engine really work.
@@patrickderubis4527 well that’s cool but it does so don’t put one on your Jeep I don’t care. Easy business for guys like me who have to replace stuff that doesn’t exist to guys like you.