Very ingenious !!! Bravo !!! Just one simple improvement to be made: to cut boards of various thickness, replace the 4 screws on the sliding rails with 4 butterfly bolts and nuts.
Yo no haría esa guía de madera..pues con el tiempo se gastará la madera y los cortes no serás exactos..sería bueno de aluminio o de perfil de fierro..se gastarán en mucho tiempo.. saludos desde Chihuahua Chihuahua
cool one, Id combine it with another, the way top slider is solid piece with one clean cut(for clearance) and is connected on 4 short arms with movable joints on sides like animal. You lift it, put a wood for cutting under it and push the slider part towards u, so it looks like laying dog and the weight of slider part holds wood pinched on place, clean cut
I think the platten the saw slides on should be the full width so as to provide zero clearance, or maybe you use a 3mm piece of sheetgoods to provide the zero clearance, but be removable for bevels. I also think the platten should sit on the workpiece of whatever thickness, again for the zero clearance. For the fence, I would prefer dog holes at positions for critical angles, 30, 45 and 60 degrees perhaps, and the fence could engage in them with built-in bench dogs.
Hola que tal... sabes que yo creo que las medidas la vamos sacando en base a la sierra circular que tengamos cada uno. No todas son de la misma medida. Generalmente éstas estaciones de corte no son muy grandes. En la filmación parece todo muy grande , pero si te fijas en el semicírculo de plástico que pega como guía de los ángulos, es un semicírculo escolar. Yo me voy a poner en campaña para hacerla. Abrazo desde la Costa de oro - Uruguay
In your videos you should state at the beginning of the video what other tools & jigs you are using that you created earlier. I notice this crosscut jig is used in so many other videos. You should reference the jigs you use at the beginning of the video and then give a link to those videos so a person can create them first if they wanted to follow along. Maybe even put your playlist in order from a jig that can be built without any other jigs to last one being the creation you made that depended on the Most jigs that you created.
Nice video. I have a question: Is it useful or overkill to have 2 circular saws, on with a special blade for ripping and one with a special blade for crosscutting, because i don't like swapping blades, making the circular saw screw dull. Hope to hear from you soon. Many thanks in advance
This does not work for me. I started to make it but the inside of the track is a bit wide and it abuts the blade so there is a space of almost an eighth of an inch I am using one by twos doe the track. This the foot of the saw will not fit snugky on the track and it will have slop
Be very careful with this design and many others similar to it. A handheld circular saw is designed to be in contact with the workpiece so there no gap for the blade to yank the workpiece up into if binding occurred. This design has a fixed amount of space between the base and the rails so there’s always a problem gap unless the jig was made for only one type of board. Just be careful with your support hand holding the workpiece down. If the blade binds and lifts the workpiece, fingers are at risk of pinching or worse.
Replay the video, stop on the times when you see his measurements. I've watched this video three or four times, I've altered his design to suit myself. You can do the same thing. Even if there Were blueprints, he'd be selling them... would you buy them or would you expect them for free? Also, you don't need him to tell you everything... where's your own creativity?
Please don't use the tool sounds in a soundtrack. The constant buzzing of the saw and other tools in the background when no such tool is being used in the shot is very annoying .
I was a little worried about installing the blade after reading a couple of reviews. But it was amazingly easy. Took about 1 minute. Works great ua-cam.com/users/postUgkxjpBI8OOeUXib_iT7UomCrQ-uauwZJ62c . Cuts easily and is perfect for pocket cuts I needed to make for replacing some old deck boards.
Thank you, the best and least complicated one I've seen. Had 18 saved and just deleted them. 👍👍
Thank you for watching!
Same here.
The idea is very good and creative, very useful for me, a carpenter, greetings from Indonesia
very nice and simple idea, love it. any way you could share your measurements
Best jig i HAVE SEEN SO FAR !!
Man, I’m glad the almighty algorithm sent you my way. This and you are exactly what I needed. Subscribed.
Very ingenious !!! Bravo !!! Just one simple improvement to be made: to cut boards of various thickness, replace the 4 screws on the sliding rails with 4 butterfly bolts and nuts.
The idea is really genius
Alat rakitan yang sangat bagus dan bermanfaat
The sound track is really awesome .
Клас,спасибо за ролик нет слов.
Amazing idea. I love it
Très beau travail 👍
Thanks!
Ótimo trabalho o resultado perfeito
0
Muy ingenioso y ,uy práctico. Excelente trabajo. 🌟🌟🌟🌟🌟🌹🌹🌹🌹🌹🇵🇦
If my blade rotates anti-clockwise will it pull up the wood
You are a genius
Complimenti bravo grazie dell'idea
Yo no haría esa guía de madera..pues con el tiempo se gastará la madera y los cortes no serás exactos..sería bueno de aluminio o de perfil de fierro..se gastarán en mucho tiempo.. saludos desde Chihuahua Chihuahua
Si amigo tal cual seria perfil de hierro es mejor, pero quiero saber tambien las medidas de las maderas.
ua-cam.com/video/93w8D2BVMOA/v-deo.htmlsi=hI_9CctOJ22HD4-Y
ua-cam.com/video/8fRmIsE4mlA/v-deo.htmlsi=rntlvZ-ubUc-9cp7
Awesome 💟
Ficou otimo 🎉parabens
pnplu😊
Bagus vidionya
En vez de esa música pichurienta deben explicar lo q hacen, y uno con gusto se los agradecería. Ya paso el siglo del cine mudo.
这个视频非常实用简单易懂，我实习做一个。
Hello
Simple and good video
Beautiful
Now that's bloody smart!
Mantap bang smg sokses
Thanks!
Mantap boss
Assistindo aqui no brasil muito o vídeo
عاش 😍🤝
Mantap bosku
ฉาก3เหลี่ยมแบบนี้หาซื้อที่ไหนครับผมไปดูที่โกบอลไม่มีครับ
Bacana parabéns.
Qual a espessura desse madeirite que você usou?
Perfecto!!
Nice job useful video
very good idea,,,
very good !
cool one, Id combine it with another, the way top slider is solid piece with one clean cut(for clearance) and is connected on 4 short arms with movable joints on sides like animal. You lift it, put a wood for cutting under it and push the slider part towards u, so it looks like laying dog and the weight of slider part holds wood pinched on place, clean cut
10:30 90 degrees 😳😳😳
Very2 good idia 👍👍👍💯
Thanks!
It is amazing.
Exelente amigo 😊
Excelente tú trabajo 👌👌💯, saludos cordiales desde Asunción, Paraguay 🇵🇾
Thank you!
Ficou ótimo parabéns
好清楚的敎學.....超愛的💌
Excellent idea.
It makes you want ! good job !
👌👍 Good work keep it up
Do you have brushcutters? Cut the claws!
Hoy mismo la hago, muchas gracias
Congratulations to you
It looks like he uses one by twos for the rails and maybe a two by three for the plywood siding. Is that right?
otimo trabalho.
muy buena!!!
exelente video amigo faltaron las medidas de la guia para hacerla puedes darlas grascias
I think the platten the saw slides on should be the full width so as to provide zero clearance, or maybe you use a 3mm piece of sheetgoods to provide the zero clearance, but be removable for bevels. I also think the platten should sit on the workpiece of whatever thickness, again for the zero clearance. For the fence, I would prefer dog holes at positions for critical angles, 30, 45 and 60 degrees perhaps, and the fence could engage in them with built-in bench dogs.
Look at my Parallel Guided Power Saw.
❤
ua-cam.com/video/8fRmIsE4mlA/v-deo.htmlsi=rntlvZ-ubUc-9cp7
Ficou show. Parabéns 👏 Guarujá. S p. Brasil
Felicidades muy bueno
Muy buena su idea
Tu plantilla súper.Podrías proporcionarme las medidas de las piezas, si no es abusar
Hola que tal... sabes que yo creo que las medidas la vamos sacando en base a la sierra circular que tengamos cada uno. No todas son de la misma medida. Generalmente éstas estaciones de corte no son muy grandes. En la filmación parece todo muy grande , pero si te fijas en el semicírculo de plástico que pega como guía de los ángulos, es un semicírculo escolar. Yo me voy a poner en campaña para hacerla. Abrazo desde la Costa de oro - Uruguay
Nice video
In your videos you should state at the beginning of the video what other tools & jigs you are using that you created earlier. I notice this crosscut jig is used in so many other videos. You should reference the jigs you use at the beginning of the video and then give a link to those videos so a person can create them first if they wanted to follow along. Maybe even put your playlist in order from a jig that can be built without any other jigs to last one being the creation you made that depended on the Most jigs that you created.
Many thanks for your comment!
I will note and add in my video description
@@MrHWoodworking I hope you keep making these. I am halfway through this Crosscut jig already!
Thanks for your attention!
The projects I post are in the order that I do them over time.
F rey te he he a tu y te cđ y tú ey y no Julio de
Ñññññññ
Nice !
Rek nurutan lah nyieun nu kitu 😁😁
Nice video. I have a question: Is it useful or overkill to have 2 circular saws, on with a special blade for ripping and one with a special blade for crosscutting, because i don't like swapping blades, making the circular saw screw dull. Hope to hear from you soon. Many thanks in advance
Nice
This does not work for me. I started to make it but the inside of the track is a bit wide and it abuts the blade so there is a space of almost an eighth of an inch I am using one by twos doe the track. This the foot of the saw will not fit snugky on the track and it will have slop
Hola. Me gusta tu trabajo, pero creo que sufriste un problema en la guía del lado del motor. ¿Es así?. Mi maquina casi enrrasa el montor con la base.
Be very careful with this design and many others similar to it. A handheld circular saw is designed to be in contact with the workpiece so there no gap for the blade to yank the workpiece up into if binding occurred. This design has a fixed amount of space between the base and the rails so there’s always a problem gap unless the jig was made for only one type of board. Just be careful with your support hand holding the workpiece down. If the blade binds and lifts the workpiece, fingers are at risk of pinching or worse.
What if you make sure to clamp down the work piece so it can't lift?
Pro 👍
Are there blueprints?
Replay the video, stop on the times when you see his measurements. I've watched this video three or four times, I've altered his design to suit myself. You can do the same thing. Even if there Were blueprints, he'd be selling them... would you buy them or would you expect them for free? Also, you don't need him to tell you everything... where's your own creativity?
👍👍👍
nice simple
Muito interessante e uma precisão nos cortes você pode passar as medidas obrigado angelino são Paulo Brasil
Молодец
Good,very nice
Thanks!
Muy buen trabajo, favor dar medidas
Muy b ueno pero que medidas tienen las maderas ?, saludos
Làm thế nào để liên hệ với anh. Tôi muốn đặt 1 jig
Xin hãy để lại sđt
Boa tarde amigo vc vende essa mesa de corte com serra circular qual valor dela
Avez vous lés dimension pour le bois utiliser merci
Excelente
Great job, I would like to do it 😀
Thank you! Good luck
its a best idia tank you
💪💪💪👍👍👍
Please don't use the tool sounds in a soundtrack. The constant buzzing of the saw and other tools in the background when no such tool is being used in the shot is very annoying .
Thank you! I will learn from experience
💯💯💯💯💯💯💯💯👌👍🤝
fhanks
What are the dimensions?
please include measurements of what your building
Muito bom
Quais são as medidas das madeiras😅
Please sir what is the thickness of ply board used for the base plates?
All are 15 mm
Minta testimoni dong cheng nya mas
Sir full measure mint upload thanks
Apakah bisa buatkan video dudukan grinda sleding untuk cutting granite..thankyou..
Terima kasih telah menonton dan berkomentar! Saya akan memikirkan itu.
@@MrHWoodworking thanks..
👌
¿cuales son las medidas de los materiales?
Muito boa por favor quais são os medidas dessa bancada
Những điều bạn tạo ra thật tuyệt vời
I was a little worried about installing the blade after reading a couple of reviews. But it was amazingly easy. Took about 1 minute. Works great ua-cam.com/users/postUgkxjpBI8OOeUXib_iT7UomCrQ-uauwZJ62c . Cuts easily and is perfect for pocket cuts I needed to make for replacing some old deck boards.
SIN MEDIDAS...SIN INFORMACION PARA HACERLO UNO.NO SIRVE DE NADA,IMPOSIBLE HACERLO.
Jajajs cuál imposible??? cada uno se saca sus medidas de acuerdo a la sierra de cada uno