Router Inlay Practice - The Compass Rose
Вставка
- Опубліковано 1 жов 2024
- Click the Link to Purchase the Dewalt Compact Router...www.amazon.com/...
Watch and learn as the woodworker practices a router inlay technique. In this woodworking shop class a decorative star of maple and walnut is being inlaid into mahogany.
The techniques demonstrated by the woodworker in this article are basically just for practice. He is simply testing to develop a strategy for when it becomes time to actually inlay the compass rose veneer. Practicing woodworking in the shop is a great idea. It's a good way to develop confidence in one's skills. We all know that it is better to make a mistake while practicing rather than to make an on the actual woodworking projects.
Read The following woodworking blog article about the router inlay practice...
theapprenticean...
Watch more woodworking how to projects & videos on UA-cam...
Subscribe to the UA-cam Channel:
/ appjourneyman
TheApprenticean...
TheApprenticeandTheJourneyman.com
Learn more, Experience more!
Bob Simmons - Навчання та стиль
That was really awesome even in 2022.🇦🇺🤜🏼🤛🏼🍀🍀🍀😎
i take it that was the apprentice.
SentoHug Yep
SentoHug lol yah
This guy is really bad at inlay...
Simonwallis30...
This is the first step. Picture the outcome that you want. Continue working towards it. However long it takes really does not matter at this point. The important thing is that you take one step and then the next step. Enjoy the process and learn from each step. It's really not a race. It is loving what you are doing.
I recommend that you watch these videos again and again. Become familiar with the process. Listen carefully,to what is being "said." You are on the right track.
Delicate inserts, I think more Dremel than Dewalt.
+enrico3web Agreed... something that small, I wouldn't even look over at my router. Maybe it was practice to see how steady the "Apprentice" was, I dunno. In fact, I could do this with hand tools just as quickly and with much more control. PS - why show us the calipers if you're just going to use the same piece to set the depth? O.o
You can use a straight bit to plunge. It's OK. As a beginning woodworker, keep it simple. There's really no need to go out and purchase all the special tools and router bits. Become familiar with using the tools that you have and focus on developing great woodworking skills.
Kudos back to you for using the same drawer liner. Keep up the great work.
Thanks for subscribing & thanks for asking!
The Compass Rose...please watch the video one more time.
" What angle did you cut the pieces at?" 22-1/2 degrees...a specific band saw sled was made for this cut. There are 8 main points...360 divided by 8 = 45 degrees. divide that in half is 22-1/2...there is a maple & walnut segment ...each is 22-1/2...together there are 45 degrees.
"How far did you set the stop block from the angled piece on the sled?" Depends on the size of star. Test the cut.
why not just continue using your plunge router with a 1/8th inch bit, saving the chisel work for the very end of the points? Looks great!
That would be up to the individual woodworker. The main thought of the video is to show the value of practice and also hogging most of the material out with the plunge router. For me, by the time I would remove the router bit & replace it with another bit, I'd have the chisel work nearly completed. Thanks for watching and commenting.
Why wouldn't you use a sharp scriber or knife to mark rather than draw lines then go back with the knife?
+Bob St. Cyr You ask a very good question. Obviously, do what is best for you. I almost always prefer to use a sharp knife rather than a pencil mark. However, there is always an exception to the rule and this case is an exception that I have made. Here is my reasoning...
Working with a rather small object with many angles is not very easy to hold down, cut, and secure the compass in one position. It becomes awkward to try to knife mark each and every angle. Also, if the knife marks are directed to the outside points then there is the chance of running the knife marks beyond the outside points of the compass.
So, this is why I decided to trace the compass with a pencil. Then I could take my time and draw the knife along the inside edge of the pencil lines. The cuts are best from the outside points towards the center which will eventually be routed.
with small pieces l hold them with a small drop of glue, or double sided tape, then use a knife to lift it . I always find it gives a cleaner and more accurate result.
rex Lobo...
I make all my own inlays and wood inlay banding. You can see how it's done. Just check out the other videos on my UA-cam woodworking channel.
Thanks for your interest.
Bob
Don...
It pays to watch the video a few times. Chances are there are ideas missed the first time. Also, by going back & watching again you are able to reinforce what you have learned. You will be better able to understand the sequences better also.
Give it a try and treat it like practice. It will come to you if you give it a chance. Let me know how it works for you. Enjoy the process.
Simonwallis30...
Thanks.
Simonwallis30...
The 2nd tool after the router is a Foredom flexible shaft tool. It is similar to the Dremel whereas small bits are used while being spun. In this case the Foreman is used as a smaller version of the router. Great question!
Hello Mike...
The three woods seem to have a nice contrast to one another. This video was really just a test for strategy. At some point these stars will probably going into a picture frame or jewelry box. This demonstration is one way to do it. However, it make be worthwhile creating a router template to work from if multiple stars are to be inlaid into a woodworking project.
Thanks for watching.
Woodprix has a lot of plans to choose from.
Simonwallis30...
Know that while you are driving your taxi through London Town during the day I'll be making woodworking videos for your enjoyment and relaxation.:)
Yep, you are probably right concerning the Ulmia clamps. If you can find them, get them. They are terrific accessories for the shop.
Simonwallis30...
In the US they are neither cheap or super expensive. A re-seller may hike up the cost. Keep looking. One can find variations of the Ulmia clamps in the US. I have not tried the other products. I can only speak for the Ulmia clamps.
Thanks very much for watching and for the kind words. If you haven't already, please consider subscribing.
Rich...You're welcome. Glad you're enjoying these woodworking videos. Thanks for watching.
Great video like the one with some talking .
Merci mon ami ... Si nous voulons travailler de manière créative, nous devons utiliser notre imagination et de continuer à améliorer nos compétences.
rex Lobo...
Thanks very much for watching the woodworking video and sharing your feedback.
Hi Mark...
You're welcome & thanks for watching. Greatly appreciate your feedback.
MelkMan7...
Yes, you're right. Woodworking is a wonderful art form.
Thanks for watching & commenting.
Thanks I did watch the video a couple of more times and I see you notation on the sled now. I was so focused on what you were doing the first time I simply missed it. I will try this on a smaller scale.
I am retired now, so I check your channel often. I can't wait to see what you will do next...
Don
I'll keep looking,eBay did sell them at £70 with pliers,would that equate to US cost ? I have framing clamps but your ones look a lot easier to use.keep up the good work !!
Cheers I find it quite therapeutic after driving a London taxi thru London Town all day ,couldn't find ulmia clamps on amazon either,might be as I'm in UK
Nice work!
I had the weirdest olfactory response watching this - when you began the rough plunge with the DeWalt router, I could 'smell' mahogany being milled. (I worked in a shop that cut, drilled and milled various soft and hard woods.)
I only mention this because I watched another video earlier this evening where someone used a Sharpie and I could 'smell' the ink.
But I digress, that is an excellent piece of work. I envy you, sir! Alas I no longer have access to that shop.
Never go all the way to your knife line with your chisel unless there's no more space for your chisel on the waste side of the knife line. Otherwise, you run the risk of compressing the wood fibers and moving your knife line.
nice. interesting router jig for rotary flex shaft too.
Siince subscribing I have watched every one of your videos. You have taught me so much, I am amazed. I have a couple of questions about how you made the compass rose. What angle did you cut the pieces at? Was it 45 degrees? How far did you set the stop block from the angled piece on the sled?
Thank you very much for being such a great teacher
Don Krueger
I'm just starting at getting into woodworking as a hobby, so this may be a silly question: What kind of bit are you using? Is it just a straight cut bit? I wasn't sure if I could just plunge into the wood like that to make the initial cut (I was carving a design into the middle of a flat board). Also, kudos on using the exact same drawer liner to stabilize your piece as me =)
Muchas gracias mi amigo. Recuerde que debe suscribir más.
Have to admit you've inspired me to have a go at some inlays myself ,bit concerned tho as my bandsaw isn't that great,but ill give it a go & let you know..probably in a months time the way I work !!
Nice job please don't stop making the videos every one needs to learn = thank you SIR
Hi again,the 2nd tool after the router,was that a dremmel or something similar ? Cheers for the answers as always
Thanks for taking the time to make the videos, they are very inspiring. It also beats the hell out of watching the garbage on T.V.
You're right. Woodworking is a lot of fun.
Very impressive. Thanks.
Mike
Nice work. I hadn't thought of using the router or foredom for marquetry. I just use my scrollsaw for cutting it out. It will let me swing 19 inches.Those were for peoples names on chests.
I did a compass rose out of purpleheart and sycamore, with the outer circle made of oak for a nautical rope like effect. Some nut job wanted me to do one for 50 bucks.Right..Course I didn't.
where do you get your inlays from or do you make your own
AppJourneyman you Rock!!! God bless you!!!
actually just looked again £135 !!!!! Seems a bit expensive ?
Definitivamente es usted un gran artista, felicitaciones.
just use the router to waste out the bulk, and then use a chisel as he shows here. Don't need that intermediate dremel router as you can't avoid using the chisel in the end. Also, a couple times i saw you cutting the bottom of the inlay pocket before cutting the edges (with the chisel), i can't help but think that will accidentally lift wood beyond the desired edges of the star, in particular if you're cutting with the grain.
Matt Sweetnam The title refers to practice. That’s really all it is. It’s simply a matter of getting the desired results.
i have some shapes like this one you do but i make them by a diffrent way .
you can use an easy method . you don t have to do all this work . i think it s hard and need a lot of time .
Woodwork: one of the oldest yet interesting forms of art.
are there any alternatives to using the router plunge?
n
Fun stuff.
they r beautiful
Could you use a collar and trace the inside of a pattern? Maybe a pattern made out of rigid foam. Use some hot glue to keep it in place.
+Jerry Whidby Sure. A router with a collar and template would work. My choice of of pattern material in this case would probably be 1/4" mdf or plywood. If I were cutting many I would prefer the plywood as it will typically hold its shape better than mdf. I would use double stick tape to secure the position of the template.
Will do,cheers
Awesome video. Thanks for showing it. Just out of curiosity where'd the compass come from, did you make it on the bandsaw? Do you recommend sanding the whole sheet down after you've glued in the design, whatever it may be? Thanks and Happy Thanksgiving!
Christopher Kelby Yes. The compass rose was made on the bandsaw. Yes, sand or scrape the entire surface down to make it all one level. Look for the video on how to make the compass rose. I think it may surprise you.
your welcome...Happy Thanksgiving
Cool! Thanks!
I love the tool you made for the finest part. I was wondering how to do one for myself, thx a lot!
thevilord i would honestly find it quicker with a nice sharp chisel...which he didn't seem to have!
L
I just want to thank you for all the fantastic videos you shared with us!
Hope you are well!
I miss seeing new content from you in my subscription feed.
heriberthuber54 Hello my friend. Thank you for the kind words. They are greatly appreciated! I am well and hope to share more woodworking videos with you again.
Great to hear you are well, kinda got worried there...
Looking forward to see more of your fantastic work!
Not bad could have been a bit cleaner but cool idea
alec irvine This is why it is called practice.
nice.
Красиво придумано и сделано
Good video but one question. Up until the finish I understand. But as far as getting the seem between the inlay and board when it fits into place are there any tips or tricks to getting the seam to be perfect? how do you finish it?
David Brady First and most importantly, always work towards improving your skills of getting a good fit. As you can see, this demonstration is just practice for me. The more you practice the better your skill and confidence becomes for obtaining a good fit.
Then, prior to finishing and when the glue is tacky, (almost dry) sand the areas of concern w/ very fine sandpaper. Remember to sand in the direction of the grain. Then late when glue has completely set, sand again to prep for finishing.
The Apprentice and The Journeyman thank you. Another question is how would you stain the board you are putting the inlay into. I have read about staining it prior to putting the inlay in and then putting shellac on the stain and then sanding it even so it ideally doesn't mess up the stain. Do you have any suggestions/insight?
David Brady Sure, I am aware of that strategy. For me there’s one problem and trust me, I’ve tried that method a long time ago when I was just starting out in woodworking. (Nowadays)...First of all I’m not excited about using stain. Pick a piece of wood that would look great with a beautiful, natural finish. Now, make an outstanding inlay....The best you’ve ever made. Prep it for finishing. Secondly or better yet, firstly, give it some love. Keep working on it.
The Apprentice and The Journeyman thank you so much for your insight and advice. Much appreciated.
David Brady No problem...keep me posted.