I’ve been doing commercial plumbing for decades and this guy is showing the proper procedures on every video I’ve seen. Some circumstances won’t allow you to get all the water out of the area in question. If this happens you may have to use a slip coupling to repair the leak. Doing this will allow you to cut the pipe near the leak to drain the remaining water. After it is drained you can mark your pipe so you can assure your coupling is centered before soldering your joints.
Few reasons: there's always more than one way to skin the cat. 2) a Top Notch Tradesman keeps learning, always. 3) I'm constantly recommending videos to my helpers as new skills are needed. 4) Got2learn makes some of the best plumbling instructional videos for learners and advanced DIY
Good job brother, I was a Licensed plumber for 28 years . My mentor was very hard on me but when I realized why I thanked him every time I saw him . I miss plumbing sometimes but being retired at 50 years old feels great .....
This guy knows what he’s talking about I’ve been working on pipework for more than 40 years listen to him he’s showing you how to do it the correct way.
This is fantastic . As an industrial maintenance technician I always do everything myself . However I have always found it difficult to solder copper pipes correctly . I was having a miserable time with my new hot water heater installation . Your advice saved me countless hours of work . Thank you so much for the help ! God bless ! (New subscriber)
Being a home handyman, I noticed that sometimes I could not get the solder to wick cleanly. I was picking up materials at our local hardware store where they have experienced tradesmen who provide invaluable advice. The plumber explained to me that paste flux has a limited life - a few months can make it tougher to work with - and mine was years old. Sure enough, the cheap can of flux I bought was immensely better than the can I had for so many years.
As a professional hvac tech, this vid has filled in some of the gaps in my soldering education. Soldering has never really been my strong point0 mostly because my teachers never really covered this stuff in this sort of detail. Thanks!!!
Plumbing is an technical art ! I know a lot of plumbers and they are far from being artists. But I also know a few that are truly plumbing artists, It's so satisfying to see their work.
Electrician here. Couldn't fix a leak in a sprinkler system I'm installing, and this was the video that showed me how to fix this issue and why it happened. Great show! Thanks plumber!!!
Both plumbing and cable running is about the simplest thing you could do, other electrical is hard, i think you guys are too overpaid compared to the kind of work mechanics and boilermakers do
@@SH19922x Go fix a hundred shit filled toilets and busted plumbing stacks and you'll change your tune - and clothes. It depends on the job and work location. Dealer mechanics might work fast but they're inside a warm shop. Boiler makers - not the best environment , assuming they're in an actual boiler. But I've worked with many BM, who we not eager to work. So, your statement needs further thought and explanation. I guess your exposure to the trades is limited to UA-cam. This video shows a basic repair in an easy to access area - thats not usually the situation. Get out there And bust a knuckle... Cheers
Thank you thank you. i fixed an old copper pipe that haunted me for years. and finally now fixed it after watching your vid. it was in a tight no room spot. Your hint on using vice grips to separate clean sand and resolder using wet rags and I used tin foil as backing to stop fires. Really worked! It's great that people like you help people like me.🙂 Good Karma to you.✌
Take a tin can, cut both ends off, cut down the side and flatten it out. Tap holes in each corner with a nail, and use wire to hang it behind your soldering area. Reusable.
I thank you for boosting my confidence! I was a little hesitant about fixing a major plumbing repair after our current freeze. I took the time to watch 3 of your videos and it all made perfect sense! I am glad to report no more leaks!
I just refitted an old pipe and soldered everything on my own (5 fittings and 2,5 mtrs of copper). That worked quite well (even when I needed to start all over again bcs I screwed up the correct length..) because of your excellent tutorials - thanks. That was the second time I ever soldered but even for the first time, your videos already helped me out. (the first project is 2 years old without a leak).
My father was a master at this. Unfortunately, I never payed close attention and he has passed away. This video and your others have been invaluable in filling the gaps in how this is done for me. Many thanks!
Thanks for a great video! It has been decades since my dad taught me how to sweat pipe. He’s no longer around for questions, and I have forgotten almost as much as I had learned back then!
Thanks very much. My mistake has been applying too much heat & flux to both ends of the pipe & then putting more flux after after running the solder into the pipe. I think your video has corrected these mistakes for me .
I am doing house renovations in Southern France. I watch these videos regularly. This one is just perfect. Presentation etc, just the best. Thanks a lot.
Thanks a lot for your videos my friend. I watched your unsolder to remove redundant water line and I installed a new one and of course soldered. It was my first time and I’ve ran the line for days now and absolutely no leak thankfully. I followed your unsolder and solder copper pipe videos and it was a success! Thank you very much!
I served my time as a maintenance engineer at a company in England that produced heat exchangers. There was a lot of soldering and brazing involved in the production of heat exchangers and there was a saying prevalent amongst my peers, and that was that, in both of these processes, "Cleanliness is Godliness". You can be too dirty, but you can't be too clean. This is always number one in my book but doesn't undermine your excellent advice.
my dad was a plumber but always did the work and never taught me anything beyond holding a light. LOL just like he did when working on cars. But I am GREAT at holding a light but now have the confidence to try some simple plumbing repairs.
You covered everything on how to fix this leak in short and interesting time, thank you!!!! I love how you explain things and the consequences of not following directions.
Thanks. The tip about wrapping adjacent joints with a wet rag is something I wish I had known a number of years ago. It would have saved me a couple of trips from my isolated cottage to the closest hardware store.
EXCELLENT VIDEO! Easy to follow, thorough explanation covering all the principles involved, by someone who really knows what they are talking about. Giving many important details, but just the right amount to enlighten without being boring. Thanks for doing this.
This is the best I’ve seen, in every way. - Instructions - Graphics to illustrate (amazing) - And lastly how conscientious you are. Keep up the great work sir. We DIY’ers salute you. 👏👏👍👍 Subscribed ✅
Got2Learn I’m sure it will. So many cling on to tips and hacks but it’s a breath of fresh air to follow someone like you who so genuinely and generously wants to help. 👏👍
Thank you from England. Very clear video of 'how to' and thank you for giving the reasons why you don't do certain things and for demonstrating the consequences. It is all a useful learning curve.
Thank you so much for your videos. I did my first ever pinhole repair based on two of your videos. Desoldering and this one. I thought I would have to replace the entire t-joint but your desolder video made this fix so much easier. I purchased all the items you recommended including the fire protector. Which, upon inspection, whomever did the previous work in that space did not use one as I could see burned wood. Anyhow, your videos are great. Thank you again.
Great information. I was just about ready to do what you said not to do and I decided to watch your video first. You saved me more headaches. What I really liked is that you not only told me what not to do and what to do but you also showed why. When I un-soldered my leaking joint, I discovered that there was an un-soldered path from the front to the back of the joint that probably wouldn't have been fixed by adding solder at the joint. Thanks again.
I wish there was a channel like this for every trade. It would be the perfect maintenance manual for everything. How to fix you car, your plumbing, your electrical, your windows, your roof, your floor, High quality content that covers all the potential errors and their repercussions. What you are doing is amazing. Thank you for all the great work.
Good video, my dad always wiped the excess solder from each joint you would never find a drip of solder on any of his joints. If one ever leaked he fixed it on the spot. The only time one would leak is in tight quarters. People don't take pride in their work. my dad was not a plumber, he was a refrigeration maintenance man. He also knew electrical.
Wow @Got2Learn @1:45 you literally just taught me something that no other soldiering video ever did. And now I realize why im having so much trouble soldering. THANKS!
I retired my torch, after Ridged came out with the ProPress. Haven’t had a leak in years. But you method an theory is true. Never, reheat to fill a void. Master Plumber for 20yrs.
Thank you so much for this. also I thought it was extremely cool that you went to the trouble to actually cut this joint in half so that everyone can see what’s happening on the inside. This is such a great video.
You really know your stuff. I have looked at many videos on this as I had the same problem recently, and man you explained it the best and the reason for doing it. I was frustrated, as I always screw up when I have to solder vertical bottom part. I thank you, I followed your explanation and it worked out great. Keep up the good work.
Thank you! I was getting frustrated with my solder joints leaking (trying to add a "T" to an existing cold water line). I kept re-fluxing and re-soldering (the wrong way) and it wasn't getting any better. Then I watched your video. I spent a few minutes removing the T (using your vise grips/hammer technique), sanded the insides and outsides as well as I could, re-fluxed, refitted, and re-heated. It took the solder perfectly the first time and I haven't yet seen a leak. I didn't know that about "not overheating the joint". I think that's probably what caused my original failures. When I disassembled the joint I noticed that there was bare copper inside the T where there should have been solder. I suspect the flux boiled away, as you cautioned against. There's definitely something to be said for doing it the right way the first time.
This video provided exactly the direction I needed to fix a leaking outdoor shut-off for my garden hose faucet. I had to heat up and remove the old one then prep the copper pipes on either side and install a new one. The best part about this video and the others I’ve begun watching is not only are we being shown how to do something, there is also en explanation as to why it’s done that way as well. I like being able to do things like this on my own, but being able to do them properly and to code is monumental. Huge thank you for sharing these videos!
I'm a professional plumber, so of course I want to toss in my $0.02 worth: Copper pipe that has water inside is nearly impossible to solder. The water becomes steam when you heat it, and the steam escapes through the joint you're trying to solder, keeping the metal from reaching soldering temperature, and pushing the partially melted solder out of the fitting. One of the best ways to overcome that if the pipe can't be completely dried inside is to leave an open fitting nearby, such as by using a screwed adapter for the last fitting to make. With 1/2-inch copper pipe, it's possible to solder if you can dry out about 10 inches of pipe away from the fitting to be soldered. The bigger the pipe size, the further away from moisture your soldering operation needs to be. In the first example here--if it's 3/4 or 1/2-inch pipe--it's better to cut the section out and use new fittings--with couplings--to make the repair, because it's so hard to get the inside of an already-soldered fitting clean enough. There are good tips and correct techniques in this video, but don't ignore the part that says soldering is a skill that takes practice. If you've never soldered copper pipe before, a repair that a pro could do in 10 minutes will be an hour or more of frustration for you.
How about stuffing bread up the pipe to stop dripping water? I think glutinous is best. I’m going to try a bagel. Plain, without cream cheese, onions, tomatoes, or smoked Salmon. The pressure will blow it to the first open tap and the water will dissolve it.
@Aww BS. Perhaps true for many, I will concede that the skill is not easy to learn, and that caution is advised, but the categorical abstinence is a bridge too far. I just repaired a faulty “professional” installation that failed prematurely. But it took me 5 days, and was very stressful. Your advice is good for most, but not all.
@@diyjohn9584 … sure you can, if your really worried about bread residue you can flush and refill the system once the work is completed (that’s good practice anyway to remove flus residues etc.)
SO good of you to post these clips. Brilliant. Really building my confidence to do the pipework at my father’s on Monday! My Plumber let us down 😱 The kitchen fitter is coming on Tuesday for 5 days, so I am now going to have to: - move the mains stopcock 2ft to the right - move external tap pipe 3 ft to left (installing compression valve) - extend cold water pipe feed to boiler - extend pipe 3 ft to right, install compression valve near mains stopcock - move taps over 2 feet (install compression joints with hot/cold taps) - install compression joints to the washing machine Slightly over optimistic for a first attempt, but hey ho.🤞🏼
Thanks so much for the video. I’ve been cooling down the solder joints straight away oops also probably putting in too much solder as an insurance gambit. Luckily all my joints have been leak free except yesterdays oops again. Very grateful again showing me the correct way to unsolder and make good the repair….
His next video will be on open heart surgery and after that on Spelunking on Mars. The guy can do everything and does everything as long as they’re in stock footage for him to overdub
@@gadooooo1 I guess you're thanking him for doing the research for us and putting it in layman's terminology ? Then I should be thank him for that as well. Just about every video I watch of his, I am reminded of lost knowledge and some new tips I've yet seen. As the 'dubbing' Martha would say, "That's a good thing".
An excellent tutorial on fixing a joint. I was going to just reheat the joint and add more solder. I used your instruction and removed the leaky fitting only to discover it was a cold joint with some bare copper still showing on the joint. I removed fitting and re-sanded the copper and re-sweated joint and now all is well Thanks!
This video clearly explains some of the pitfalls that I probably would not have avoided had I just gone forward without educating myself first. Thank you for clearly explaining everything during the demonstration!
Thank you for this! I haven't done a lot of copper, but I've never had a problem before. I did a few joints in a bathroom remodel today, but had one that the solder was 'being weird on' and had a pinhole leak when I turned the water on. It was also my first time using MAP gas and it overheats the joint really quick apparently. I cleaned it all off and followed the steps here and so far so good.
Recommend using dry rag (not wet) to remove the molten solder... as soon as a wet rag hits it the solder hardens (not the objective).. wear golved to avoid burns. great video
Very helpful video. I am renovating my master bathroom and one seam leaked, perhaps from shifting the pipe to fit other fittings and lengths, and broke the seam. TIP! Use a wet/dry shop vac to evacuate residual water in the pipe. Put the vacuum hose end over the pipe opening, squeeze your fist around the end of the hose over the copper to create an air tight seal and vacuum as needed. Be sure to open a nearby valve to allow air to travel with the water. Dry the pipe with a torch for best results.
Nothing in this world is guaranteed cept death n taxes. Sure as hell not having plumbing leaks. I’ve been doing it for 18 years n still get a leak now n then. Rare but it happens. I have coworkers with 20-30 years experience and same results
The technique at 6:00 in was super helpful! I first tried the lazy way and heated the (elbow in this case) and just added more solder. Bzzzzzttt ...nope. In fact the pinhole got worse. What I did do, a bit different than you, is heat up the joint, then gently tap the vice grips until the connection is MOSTLY out but still hnaging on at the edge. I sandpapered the pipe, bought the proper flux (I had tinning flux) and just put flux on the pipe, heated the elbow joint, tapped the vice grips gently until the parts were fully conneted the added solder. This seemed to work for me, going to inspect all connections for leaks in 24hrs but so far looks solid. GREAT video!
Excellent video, thank you for being so detailed and specific. As a doctor, I know how paying attention to the details saves lives, and in your case, you save people time, which leads to saving lives. Thank you Sir.
One of the best how-to videos I've seen. Good visuals, clear and concise instructions. No if I can only find another one on the topic I was looking for: if lead free solder can be used on a joint already tinned with leaded solder...
Seems like a good idea, it might allow reflow of the joint without the water needing to be cleared out and the joint fully disassembled to redo it, as it would be just a continuation. Just would have to find a way to pressurize it though.
I am now more knowledgeable as a DIY home fixer for watching this. Thank you for the video. I have been doing it wrong for part of it and now know the correct way to fix my next leak. Wrapping the other connections to a three way joint is something I never considered.
First, I wanted to thank you for this and your other videos. Your well explained techniques have helped myself and I am sure many other weekend warriors become better at plumbing by improving skills with your pro tips and techniques. I thought I was pretty good (always got the job done), but now I am much better. I am currently working on an older 3 story Victorian home with mostly copper pipe (changed) and a few runs of the old iron which I can't easily access. It would be great if you could do some videos on older homes and working with old stuff with some tips on replacing inaccessible pipes (possibly with pex ?)and also dealing with old shut off valves. I have not had any luck trying to disassemble most of the older screw valves when the washers let go when you are trying to fix something simple and now it turns into a much bigger project.
I have been plumbing since '84 (or so). Excellent post. Your basics of fittings being "mechanically clean", and properly fluxxed, are spot on. Strangely, the necessity of clearing the line of standing water, is the most "frequently forgotten. Good coverage! I ordinarily open the discharge side of the meter, in order to drain down outdoors.
Brilliant video the detail of why you need to what happens if you don't. I was going to give up trying to remove an elbow joint that had been fine for almost 20 years but started weeping because the pipes have to be unclipped to remove a decorative fitting my wife added so over the years this movement must have caused a crack in the joint. It's funny I tried the first bodge-it method of flux and solder to patch it, like you said it doesn't work. It's only when I used the lockable wrench with a hammer that I succeeded. After that I did precisely what you said - it worked first time!
Great vid, I just have one suggestion. The prep of the pipe has a lot to do with improper joining. What I'm referring to is when you sand the pipe, a lot of people make the mistake of going around in a circle. But if you go parallel with the pipe and create straight lines, the solder has a easier path to flow versus going over the miniscule ridges or "whoops" like I call them. Kinda like a dirt bike at a race track. Good luck
U know that the plumbers are going to hate/love you because many viewers will try to half ass what you are so professionally teaching here Thanks a millon excellent tool
This video legit saved me & my husband! We had 1 tiny pin hole on the cold pipe joint on the shower rough in valve.. we followed these exact steps & it worked like a charm! Thank you!!
It helps to clean the outside of the fitting and leaving a small bead as a structural reinforcement. Do not jostle that leads to a”cold solder joint”. Let it naturally cool as per the video.
Thanks for this video! As another plumber stated: Soldering a joint with water inside causes steam to build up. Steam will push out the joint solder and flux which you are attempting to install.
I’m a 5th year apprentice and currently in plumbing school/ programs. Master plumbers and teachers who have done studies about soldering taught us to always run the torch or the heat all around the pipe while soldering not just heating the bottom and expect to have a strong joint. We actually cut the pipe and see the inside. I haven’t had any leaks by doing it the way we were taught.
That's interesting to think about. Best to be consistent in developing the art of soldering. But, in relatively small pipes, if you apply heat to one general area of a fitting, when the opposite side is JUST hot enough that the solder flows freely, the whole fitting MUST be hot enough to allow the joint to fill completely with solder.
Your videos and graphics are really good at illustrating what you are talking about. And you are very thorough about giving all the required information. Great video, thanks for posting.
@@Got2Learn I forgot to mention, I had just come in from using some of you information. I'll finish the job tomorrow. The last time I did any of this was 20 years ago. I did pretty well. But I could have done better after seeing your vids lol Thanks again.
Very helpful for upcoming professionals. Enjoyed watching the video! One thing I do is use a dry rag when whipping the hot Soldier of the pipe makes it smooth and clean to get right back into the fitting
I haven’t been working in a trade for almost 14 years due to my injury and watching videos like these gives me nostalgia.🥺 I’ve probable done millions of soldering joints if not more and for sure I had some hiccups in the beginning 🤣
I completely agree with the problem of leaving some water in the tube. it first prevents the correct temperature to be obtained. And then, when you are doing the soldiering, the low part keeps cold because the energy you bring is mainly used to evaporate the water. Especially true if the water is constantly renewed because you warm the below tube where it stays !!
When I started in the plumbing trade in 1976 I was a apprentice,one of the plumbers would say all you need to know is torch stricker solder paste sand paper, just go get it don’t you use it,after 38 years in the trade i always remembered that.
Your videos are highly informative, very technical, and has helped many DIYers like myself who need this vital information to repair and resolve these issues ourselves. Your instructions are clear, with great advise and technical "know how" to do it right. Your cutaway view makes your explanation invaluable that substantiates the do's and don'ts. You are the best at what you do, as I'm a fan for life. Keep-up the great work MF (my friend) !!
Leaks happen bro, not often but once in a while. When you've completed 100's of joints it hard to gauge that odd one. Sometimes you forget to tighten that odd compression joint. I only really dry test gas lines. There's no second chances when safety is critical. Any plumber who tells you they haven't had a leak is a liar 😜. Keep up the excellent work bruh 👌
@@Got2Learn Tru dat bro, desoldered joints which a reformed are usually actually stronger. As the joint has been coated with solder (tinning). Your videos are looking super pro bro. Really super with the editing & CGI, bravo 👌.
Thanks so much ghost! Yeah I want to do this type of editing in every video from now on, I am getting a lot of positive feedback from that, so it can only get better from now and on, :)
Ha! And always, the joint that leaks is one of the first you did, right at the back of the cupboard behind all the other pipes you've just put in! Quote from my plumbing tutor many years ago: "ALWAYS check your joints, they're like pretty women, turn your back & they are trouble.!"
@@theondebray leaks happen especially when you have apprentices on hand. We've all been there, it was us creating devastation back at the beginning. Heck, sometimes you just have one of those days when you've done an install. By the end of it you just want to get the hell out and hey presto Mr leak shows up 🤷♂️
The way I have found to be successful with copper pipe soldering is to make sure there is no moisture in or on the outside of the pipe. Keep the joint clean and use a liberal amount of flux on every surface to be soldered. If those three things are done your solder joint will adhere no matter how ugly you solder. Remembering that the solder itself chases the heat so i apply on the separate side that I am applying the torch so it will travel throughout the joint.
If you are soldering a shutoff valve on a line with any moisture in it, make sure the valve is open. Steam in a pipe will bounce a closed valve off a ceiling. 😁
You can do it with water running out through the hole. You just have to add the solder or you may use a welder and just tack bunch above the area that needs to be repaired. You also will need a grinder so you may grind the "weld" downwards over the leaky area. Obviously if you have a large enough hole you won't be able to do it with running water. Hope you learned something today. Err, hope it helps someone in the future.
Again, great video. I'm sure you have the best channel for plumbers right now. Great information, visual examples of right and wrong . Amazing. Dont stop making these. Go from tips on grounds to fixtures! That's 100+ videos . Where I work if we glued a PVC fitting 1 1/2" + . No matter how long if needed due to mistake . We use our torch to burn/soften, to peel it out. It works great to even re use. But idk if there are consequences using the method.
Hey man, thank you so much for you're comments, they keep me going. As for the PVC removal trick, I made a video about a month ago that talks "just" about this, here's the link if you wanna see it: ua-cam.com/video/UPzUBxvB8jo/v-deo.html
Join my plumbing forum for free: got2learn.freeforums.net/
I’ve been doing commercial plumbing for decades and this guy is showing the proper procedures on every video I’ve seen. Some circumstances won’t allow you to get all the water out of the area in question. If this happens you may have to use a slip coupling to repair the leak. Doing this will allow you to cut the pipe near the leak to drain the remaining water. After it is drained you can mark your pipe so you can assure your coupling is centered before soldering your joints.
Thanks Jeff 🙏🙏🙏
Jeff, thanks for providing validation so we amateurs can’t have confidence in the videos.
As a Plumber who has been doing this trade for 45 years, I give you two thumbs up. Clean joint and all.
👌👌👌 thank you sooooo much Jody!!!
Don’t forget to deburr inside n out
Why are there always tradesmen with decades worth of experience on tutorial videos?
@@station-7 some are willing to share their knowledge and experience
Few reasons: there's always more than one way to skin the cat. 2) a Top Notch Tradesman keeps learning, always. 3) I'm constantly recommending videos to my helpers as new skills are needed. 4) Got2learn makes some of the best plumbling instructional videos for learners and advanced DIY
Good job brother, I was a Licensed plumber for 28 years . My mentor was very hard on me but when I realized why I thanked him every time I saw him . I miss plumbing sometimes but being retired at 50 years old feels great .....
🤘🤘🤘
My old curmudgeon plumber gave tough love. He who has leaks buys drinks.
This guy knows what he’s talking about I’ve been working on pipework for more than 40 years listen to him he’s showing you how to do it the correct way.
;)
How do we know that YOU know what you are talking about?
LOL...sorry...couldn't resist ;-)
This is fantastic . As an industrial maintenance technician I always do everything myself . However I have always found it difficult to solder copper pipes correctly . I was having a miserable time with my new hot water heater installation . Your advice saved me countless hours of work . Thank you so much for the help ! God bless ! (New subscriber)
Never say hot water heater ,just say water heater,if the water is hot you don’t need a heater.
Not many 100% explanatory videos like this. Respect !
I appreciate that! Thanks for sharing ;)
Being a home handyman, I noticed that sometimes I could not get the solder to wick cleanly. I was picking up materials at our local hardware store where they have experienced tradesmen who provide invaluable advice. The plumber explained to me that paste flux has a limited life - a few months can make it tougher to work with - and mine was years old. Sure enough, the cheap can of flux I bought was immensely better than the can I had for so many years.
Laco Flux, Sterling solder, Mapp (yellow) gas for your torch. You will be invincible!
Get a tradesman to do it.
Never had trouble with flux, clean , with proper heating……..water, closed system causing steam, or air expansion….
@@blackpine6693 same here and I’m still using a quart of flux I bought in 1996
@@johnlennon1151 what, so they can smash big holes in your house just to fix a single joint and charge you £250 for the privilege? No thanks.
As a professional hvac tech, this vid has filled in some of the gaps in my soldering education. Soldering has never really been my strong point0 mostly because my teachers never really covered this stuff in this sort of detail. Thanks!!!
You solder your line sets?
Plumbing is an technical art ! I know a lot of plumbers and they are far from being artists. But I also know a few that are truly plumbing artists, It's so satisfying to see their work.
🙏
Electrician here. Couldn't fix a leak in a sprinkler system I'm installing, and this was the video that showed me how to fix this issue and why it happened. Great show! Thanks plumber!!!
Awesome man, i'm glad I could help out ;)
@@Got2Learn Me too!!!
Both plumbing and cable running is about the simplest thing you could do, other electrical is hard, i think you guys are too overpaid compared to the kind of work mechanics and boilermakers do
@@SH19922x Go fix a hundred shit filled toilets and busted plumbing stacks and you'll change your tune - and clothes. It depends on the job and work location. Dealer mechanics might work fast but they're inside a warm shop. Boiler makers - not the best environment , assuming they're in an actual boiler. But I've worked with many BM, who we not eager to work. So, your statement needs further thought and explanation. I guess your exposure to the trades is limited to UA-cam. This video shows a basic repair in an easy to access area - thats not usually the situation. Get out there And bust a knuckle...
Cheers
Thank you thank you. i fixed an old copper pipe that haunted me for years. and finally now fixed it after watching your vid. it was in a tight no room spot. Your hint on using vice grips to separate clean sand and resolder using wet rags and I used tin foil as backing to stop fires. Really worked! It's great that people like you help people like me.🙂 Good Karma to you.✌
Take a tin can, cut both ends off, cut down the side and flatten it out. Tap holes in each corner with a nail, and use wire to hang it behind your soldering area. Reusable.
I thank you for boosting my confidence! I was a little hesitant about fixing a major plumbing repair after our current freeze. I took the time to watch 3 of your videos and it all made perfect sense! I am glad to report no more leaks!
😉😉😉
I just refitted an old pipe and soldered everything on my own (5 fittings and 2,5 mtrs of copper). That worked quite well (even when I needed to start all over again bcs I screwed up the correct length..) because of your excellent tutorials - thanks. That was the second time I ever soldered but even for the first time, your videos already helped me out. (the first project is 2 years old without a leak).
@@unwokesnake 😇😇😇
My father was a master at this. Unfortunately, I never payed close attention and he has passed away. This video and your others have been invaluable in filling the gaps in how this is done for me. Many thanks!
😇😇😇
Love the way you explained 🙏🏿… Always watch plumbers doing this and think it’s hard but now I get it.
🤜🤛
Thanks for a great video! It has been decades since my dad taught me how to sweat pipe. He’s no longer around for questions, and I have forgotten almost as much as I had learned back then!
Thanks very much. My mistake has been applying too much heat & flux to both ends of the pipe & then putting more flux after after running the solder into the pipe. I think your video has corrected these mistakes for me .
@@worldview730 😇🔥
Interesting, I usually go for the 'put a piece of tape on it and run away' technique. Might have to add this one to my arsenal.
🤣
Window licker
I am doing house renovations in Southern France. I watch these videos regularly. This one is just perfect. Presentation etc, just the best. Thanks a lot.
Thank you sooooooo much, share if you can, and good luck with those renos!!!
Excellent video! I'm a beginner and had a couple of leaking joints. Did what you said and it wasn't too bad to fix. No leaks now. 😊
Great to hear!
Thanks a lot for your videos my friend. I watched your unsolder to remove redundant water line and I installed a new one and of course soldered. It was my first time and I’ve ran the line for days now and absolutely no leak thankfully. I followed your unsolder and solder copper pipe videos and it was a success! Thank you very much!
I served my time as a maintenance engineer at a company in England that produced heat exchangers. There was a lot of soldering and brazing involved in the production of heat exchangers and there was a saying prevalent amongst my peers, and that was that, in both of these processes, "Cleanliness is Godliness". You can be too dirty, but you can't be too clean. This is always number one in my book but doesn't undermine your excellent advice.
my dad was a plumber but always did the work and never taught me anything beyond holding a light. LOL just like he did when working on cars. But I am GREAT at holding a light but now have the confidence to try some simple plumbing repairs.
You covered everything on how to fix this leak in short and interesting time, thank you!!!! I love how you explain things and the consequences of not following directions.
Thank you so much Dean!!!
Thanks. The tip about wrapping adjacent joints with a wet rag is something I wish I had known a number of years ago. It would have saved me a couple of trips from my isolated cottage to the closest hardware store.
Glad to help!
EXCELLENT VIDEO! Easy to follow, thorough explanation covering all the principles involved, by someone who really knows what they are talking about. Giving many important details, but just the right amount to enlighten without being boring. Thanks for doing this.
Glad it was helpful!
Videos like this are rare! Not videos about soldering, but usefull videos!
Excelent job!
Thank you so much Pero!
This is the best I’ve seen, in every way.
- Instructions
- Graphics to illustrate (amazing)
- And lastly how conscientious you are.
Keep up the great work sir. We DIY’ers salute you. 👏👏👍👍
Subscribed ✅
Awesome comment, thank you so much and I hope it goes around the world :)
Got2Learn I’m sure it will. So many cling on to tips and hacks but it’s a breath of fresh air to follow someone like you who so genuinely and generously wants to help. 👏👍
Thank you once again buddy ;)
Thank you from England. Very clear video of 'how to' and thank you for giving the reasons why you don't do certain things and for demonstrating the consequences. It is all a useful learning curve.
You are very welcome!!
Thank you so much for your videos. I did my first ever pinhole repair based on two of your videos. Desoldering and this one. I thought I would have to replace the entire t-joint but your desolder video made this fix so much easier. I purchased all the items you recommended including the fire protector. Which, upon inspection, whomever did the previous work in that space did not use one as I could see burned wood. Anyhow, your videos are great. Thank you again.
Yo uare most welcome Adam, glad to hear that it worked out for you buddy, have a good one!
Great information. I was just about ready to do what you said not to do and I decided to watch your video first. You saved me more headaches. What I really liked is that you not only told me what not to do and what to do but you also showed why. When I un-soldered my leaking joint, I discovered that there was an un-soldered path from the front to the back of the joint that probably wouldn't have been fixed by adding solder at the joint. Thanks again.
Nice to hear, yeah, I don't see the point in saying something and not explaining it, glad to hear that you appreciated that ;)
I wish there was a channel like this for every trade. It would be the perfect maintenance manual for everything. How to fix you car, your plumbing, your electrical, your windows, your roof, your floor, High quality content that covers all the potential errors and their repercussions. What you are doing is amazing. Thank you for all the great work.
That would be sick, let's hope others hop onboard!!!
ChrisFix is a decent channel for car maintenance.
@@TheSignatureK thanks!
Good video, my dad always wiped the excess solder from each joint you would never find a drip of solder on any of his joints. If one ever leaked he fixed it on the spot. The only time one would leak is in tight quarters. People don't take pride in their work. my dad was not a plumber, he was a refrigeration maintenance man. He also knew electrical.
Wow @Got2Learn @1:45 you literally just taught me something that no other soldiering video ever did. And now I realize why im having so much trouble soldering. THANKS!
You are most welcome!!!!!
I retired my torch, after Ridged came out with the ProPress. Haven’t had a leak in years. But you method an theory is true. Never, reheat to fill a void. Master Plumber for 20yrs.
Awesome, thanks ;)
Thank you so much for this. also I thought it was extremely cool that you went to the trouble to actually cut this joint in half so that everyone can see what’s happening on the inside. This is such a great video.
You really know your stuff. I have looked at many videos on this as I had the same problem recently, and man you explained it the best and the reason for doing it. I was frustrated, as I always screw up when I have to solder vertical bottom part. I thank you, I followed your explanation and it worked out great. Keep up the good work.
Awesome man, mission accomplished for both of us, don't forget to share if you can, it really helps out, have a great day Ron!
Thank you!
I was getting frustrated with my solder joints leaking (trying to add a "T" to an existing cold water line). I kept re-fluxing and re-soldering (the wrong way) and it wasn't getting any better.
Then I watched your video.
I spent a few minutes removing the T (using your vise grips/hammer technique), sanded the insides and outsides as well as I could, re-fluxed, refitted, and re-heated. It took the solder perfectly the first time and I haven't yet seen a leak.
I didn't know that about "not overheating the joint". I think that's probably what caused my original failures. When I disassembled the joint I noticed that there was bare copper inside the T where there should have been solder. I suspect the flux boiled away, as you cautioned against.
There's definitely something to be said for doing it the right way the first time.
🤘🤘🤘
While I don't think I'll ever do this myself, I can appreciate a well made informational video. I watched it all just because it was so interesting :)
🙏🙏🙏
This video provided exactly the direction I needed to fix a leaking outdoor shut-off for my garden hose faucet. I had to heat up and remove the old one then prep the copper pipes on either side and install a new one. The best part about this video and the others I’ve begun watching is not only are we being shown how to do something, there is also en explanation as to why it’s done that way as well.
I like being able to do things like this on my own, but being able to do them properly and to code is monumental. Huge thank you for sharing these videos!
Awesome comment, thank you so much Jason, good luck with your future repairs!
I'm a professional plumber, so of course I want to toss in my $0.02 worth: Copper pipe that has water inside is nearly impossible to solder. The water becomes steam when you heat it, and the steam escapes through the joint you're trying to solder, keeping the metal from reaching soldering temperature, and pushing the partially melted solder out of the fitting. One of the best ways to overcome that if the pipe can't be completely dried inside is to leave an open fitting nearby, such as by using a screwed adapter for the last fitting to make. With 1/2-inch copper pipe, it's possible to solder if you can dry out about 10 inches of pipe away from the fitting to be soldered. The bigger the pipe size, the further away from moisture your soldering operation needs to be.
In the first example here--if it's 3/4 or 1/2-inch pipe--it's better to cut the section out and use new fittings--with couplings--to make the repair, because it's so hard to get the inside of an already-soldered fitting clean enough.
There are good tips and correct techniques in this video, but don't ignore the part that says soldering is a skill that takes practice. If you've never soldered copper pipe before, a repair that a pro could do in 10 minutes will be an hour or more of frustration for you.
How about stuffing bread up the pipe to stop dripping water? I think glutinous is best. I’m going to try a bagel. Plain, without cream cheese, onions, tomatoes, or smoked Salmon. The pressure will blow it to the first open tap and the water will dissolve it.
@Aww BS. Perhaps true for many, I will concede that the skill is not easy to learn, and that caution is advised, but the categorical abstinence is a bridge too far.
I just repaired a faulty “professional” installation that failed prematurely. But it took me 5 days, and was very stressful.
Your advice is good for most, but not all.
@@OnerousEthic can not use bread in a closed system. I flare and install flare joints for those.
@@diyjohn9584 … sure you can, if your really worried about bread residue you can flush and refill the system once the work is completed (that’s good practice anyway to remove flus residues etc.)
No empty talk. Straight to the point. Great shots. Keep up the great work man!
🤗🤗🤗
SO good of you to post these clips.
Brilliant.
Really building my confidence to do the pipework at my father’s on Monday!
My Plumber let us down 😱
The kitchen fitter is coming on Tuesday for 5 days, so I am now going to have to:
- move the mains stopcock 2ft to the right
- move external tap pipe 3 ft to left (installing compression valve)
- extend cold water pipe feed to boiler - extend pipe 3 ft to right, install compression valve near mains stopcock
- move taps over 2 feet (install compression joints with hot/cold taps)
- install compression joints to the washing machine
Slightly over optimistic for a first attempt, but hey ho.🤞🏼
Awesome, I am so glad I can help you out, and I hope everything goes well for you and your father!
Thanks so much for the video. I’ve been cooling down the solder joints straight away oops also probably putting in too much solder as an insurance gambit. Luckily all my joints have been leak free except yesterdays oops again. Very grateful again showing me the correct way to unsolder and make good the repair….
I know I've viewed a few of his videos as I recognize his voice. Always learn or reminded of things every time. He makes youtube the success it is.
So very nice of you :) thank you so much!
His next video will be on open heart surgery and after that on Spelunking on Mars. The guy can do everything and does everything as long as they’re in stock footage for him to overdub
@@gadooooo1 I guess you're thanking him for doing the research for us and putting it in layman's terminology ? Then I should be thank him for that as well. Just about every video I watch of his, I am reminded of lost knowledge and some new tips I've yet seen. As the 'dubbing' Martha would say, "That's a good thing".
Your details show you are an experienced plumber. Great job!!!
I appreciate that, thank you very much!
Great common sense is the best teacher.
This video is very well presented and understandable.
Thanks for the information.
Thank you so much Seann!!!
An excellent tutorial on fixing a joint. I was going to just reheat the joint and add more solder. I used your instruction and removed the leaky fitting only to discover it was a cold joint with some bare copper still showing on the joint. I removed fitting and re-sanded the copper and re-sweated joint and now all is well Thanks!
Awesomeness!!!!
This video clearly explains some of the pitfalls that I probably would not have avoided had I just gone forward without educating myself first. Thank you for clearly explaining everything during the demonstration!
Thank you for this! I haven't done a lot of copper, but I've never had a problem before. I did a few joints in a bathroom remodel today, but had one that the solder was 'being weird on' and had a pinhole leak when I turned the water on. It was also my first time using MAP gas and it overheats the joint really quick apparently. I cleaned it all off and followed the steps here and so far so good.
😉
Recommend using dry rag (not wet) to remove the molten solder... as soon as a wet rag hits it the solder hardens (not the objective).. wear golved to avoid burns. great video
Great point!!!
Very helpful video. I am renovating my master bathroom and one seam leaked, perhaps from shifting the pipe to fit other fittings and lengths, and broke the seam. TIP! Use a wet/dry shop vac to evacuate residual water in the pipe. Put the vacuum hose end over the pipe opening, squeeze your fist around the end of the hose over the copper to create an air tight seal and vacuum as needed. Be sure to open a nearby valve to allow air to travel with the water. Dry the pipe with a torch for best results.
An absolute must, here's a video I made on this: ua-cam.com/video/lNUAX6mJTlA/v-deo.html
Loving the statement " I guarantee that if you've done it right it wont leak " made me chuckle. 👍
;)
Nothing in this world is guaranteed cept death n taxes. Sure as hell not having plumbing leaks. I’ve been doing it for 18 years n still get a leak now n then. Rare but it happens. I have coworkers with 20-30 years experience and same results
Great vid. I’m blown away by the fact that some pipes in some countries are copper
I am not in industry and probably won't ever be, but your learning is great.
Great videos! Did my first solder today. 9 joints for a water supply setup with a washer/dryer. Watched a bunch of your videos first! Thanks!
No leaks btw 😁
@@commercialconcepts2198 so happy it worked, rock on 🤘🤘🤘
Very thorough, well organized and great visual aids.
Thank you Jeremy!
The technique at 6:00 in was super helpful! I first tried the lazy way and heated the (elbow in this case) and just added more solder. Bzzzzzttt ...nope. In fact the pinhole got worse. What I did do, a bit different than you, is heat up the joint, then gently tap the vice grips until the connection is MOSTLY out but still hnaging on at the edge. I sandpapered the pipe, bought the proper flux (I had tinning flux) and just put flux on the pipe, heated the elbow joint, tapped the vice grips gently until the parts were fully conneted the added solder. This seemed to work for me, going to inspect all connections for leaks in 24hrs but so far looks solid. GREAT video!
Your way is even better than mine, good job 😄
Excellent video, thank you for being so detailed and specific. As a doctor, I know how paying attention to the details saves lives, and in your case, you save people time, which leads to saving lives. Thank you Sir.
Yes, thank you very much!
And thank you for your service webmedics
Non professional here that has done a fair bit of pipe soldering. I liked this video. I learned several things even though I've done this many times.
🙏🙏🙏
You do an awesome job with these videos, very educational. Thumbs up.
One of the best how-to videos I've seen. Good visuals, clear and concise instructions. No if I can only find another one on the topic I was looking for: if lead free solder can be used on a joint already tinned with leaded solder...
Glad it was helpful! To answer your question, it's totally fine if both mix together, don't worry ;)
@@Got2Learn Very kind of you to answer. Thanks! :-)
My pleasure ;)
On large jobs I always test with air pressure. Makes any leak easy to fix.
Great videos.
Seems like a good idea, it might allow reflow of the joint without the water needing to be cleared out and the joint fully disassembled to redo it, as it would be just a continuation. Just would have to find a way to pressurize it though.
I am now more knowledgeable as a DIY home fixer for watching this. Thank you for the video. I have been doing it wrong for part of it and now know the correct way to fix my next leak. Wrapping the other connections to a three way joint is something I never considered.
First, I wanted to thank you for this and your other videos. Your well explained techniques have helped myself and I am sure many other weekend warriors become better at plumbing by improving skills with your pro tips and techniques. I thought I was pretty good (always got the job done), but now I am much better. I am currently working on an older 3 story Victorian home with mostly copper pipe (changed) and a few runs of the old iron which I can't easily access. It would be great if you could do some videos on older homes and working with old stuff with some tips on replacing inaccessible pipes (possibly with pex ?)and also dealing with old shut off valves. I have not had any luck trying to disassemble most of the older screw valves when the washers let go when you are trying to fix something simple and now it turns into a much bigger project.
Those are all very good ideas, I will start working on those, thank you so much and have fun with your future projects buddy :)
@@Got2Learn do a video on no slip couplings
@@Eastbaypisces I have: ua-cam.com/video/ebvqSp-d8-0/v-deo.html&ab_channel=Got2Learn
@@Got2Learn yea my bad i forgot
I have been plumbing since '84 (or so).
Excellent post. Your basics of fittings being "mechanically clean", and properly fluxxed, are spot on.
Strangely, the necessity of clearing the line of standing water, is the most "frequently forgotten. Good coverage!
I ordinarily open the discharge side of the meter, in order to drain down outdoors.
Beautifully articulated. Valuable "crash course" in sweating copper!
Awesome, I love hearing that ;)
Brilliant video the detail of why you need to what happens if you don't. I was going to give up trying to remove an elbow joint that had been fine for almost 20 years but started weeping because the pipes have to be unclipped to remove a decorative fitting my wife added so over the years this movement must have caused a crack in the joint. It's funny I tried the first bodge-it method of flux and solder to patch it, like you said it doesn't work. It's only when I used the lockable wrench with a hammer that I succeeded. After that I did precisely what you said - it worked first time!
🤘🤘🤘
Great vid, I just have one suggestion. The prep of the pipe has a lot to do with improper joining. What I'm referring to is when you sand the pipe, a lot of people make the mistake of going around in a circle. But if you go parallel with the pipe and create straight lines, the solder has a easier path to flow versus going over the miniscule ridges or "whoops" like I call them. Kinda like a dirt bike at a race track. Good luck
🙏🙏🙏
Tt
they never thought me this in HVAC, good tip.
Shit, that's a great tip!
Thanks for your videos. You taught me how to solder copper before. And today you taught me to unsolder copper. Thanks for the work you do!
Rock on!
U know that the plumbers are going to hate/love you because many viewers will try to half ass what you are so professionally teaching here Thanks a millon excellent tool
Thank you so much :)
I did my first solder today, first one had to redo, second I think I just got lucky. Learn a lot today nothing like actually getting down and dirty.
The best way is clean off all the flux of the pipe and the fitting doing it you will have no problem at all .
This is the best description I've ever heard. Thank you!
You're so welcome!!!
your channel is a must for all plumbers and DIY guys/girls. Keep up the good work
Awesome, thank you so much Spy, really appreciate all your comments ;)
This video legit saved me & my husband! We had 1 tiny pin hole on the cold pipe joint on the shower rough in valve.. we followed these exact steps & it worked like a charm! Thank you!!
Glad it helped, awesome works guys!!!!!!!!!! :)
Is it just me that finds it really satisfying to watch the solder run around the joint?
No, it's a thing ;)
It helps to clean the outside of the fitting and leaving a small bead as a structural reinforcement. Do not jostle that leads to a”cold solder joint”. Let it naturally cool as per the video.
This is the most in-depth awesome soldering repair video!!
Awesome Job. Thanks.
Wow, thanks!
For horizontal pipes with residual water in them, I stuff a little piece of bread in the pipe before I soldier it. Works every time.
Thanks for this video! As another plumber stated: Soldering a joint with water inside causes steam to build up. Steam will push out the joint solder and flux which you are attempting to install.
👌👌👌
I’m a 5th year apprentice and currently in plumbing school/ programs. Master plumbers and teachers who have done studies about soldering taught us to always run the torch or the heat all around the pipe while soldering not just heating the bottom and expect to have a strong joint. We actually cut the pipe and see the inside. I haven’t had any leaks by doing it the way we were taught.
For small pipes up to 3/4", you can stay in the same spot or in the vicinity of, it won't matter.
That's interesting to think about. Best to be consistent in developing the art of soldering. But, in relatively small pipes, if you apply heat to one general area of a fitting, when the opposite side is JUST hot enough that the solder flows freely, the whole fitting MUST be hot enough to allow the joint to fill completely with solder.
And then in tight places you can't always get around the pipe with the torch.
@@wholeNwon With small pipes it always helps to use torch with wide enough flame, not just those pencil beam ones
@@dmitripogosian5084 Hard to argue with that.
Whenever possible check for leaks with compressed air. Makes fixing leaks so much easier. Well worth it
100%
VERY GOOD TIPS IM NEW TO SOLDERING ,THIS HELPED ME ALOT THANKS.👍👍
Glad I could help out :)
Your videos and graphics are really good at illustrating what you are talking about. And you are very thorough about giving all the required information. Great video, thanks for posting.
Thanks a million Jeff, have a great evening 🙏🙏🙏
@@Got2Learn I forgot to mention, I had just come in from using some of you information. I'll finish the job tomorrow. The last time I did any of this was 20 years ago. I did pretty well. But I could have done better after seeing your vids lol Thanks again.
@@jeffpurtell5676 🙏🙏🙏
Very helpful for upcoming professionals. Enjoyed watching the video! One thing I do is use a dry rag when whipping the hot
Soldier of the pipe makes it smooth and clean to get right back into the fitting
Thank you so much, yeah wiping seems to be a preference thing, I just choose not to do it, have a great day :)
Does the soldier ever complain about getting that hot?
Don't wipe the joint too soon after soldering, if the solder hasn't set fully you can crack the joint causing it to leak.
I haven’t been working in a trade for almost 14 years due to my injury and watching videos like these gives me nostalgia.🥺
I’ve probable done millions of soldering joints if not more and for sure I had some hiccups in the beginning 🤣
I completely agree with the problem of leaving some water in the tube. it first prevents the correct temperature to be obtained. And then, when you are doing the soldiering, the low part keeps cold because the energy you bring is mainly used to evaporate the water. Especially true if the water is constantly renewed because you warm the below tube where it stays !!
When I started in the plumbing trade in 1976 I was a apprentice,one of the plumbers would say all you need to know is torch stricker solder paste sand paper, just go get it don’t you use it,after 38 years in the trade i always remembered that.
Your videos are highly informative, very technical, and has helped many DIYers like myself who need this vital information to repair and resolve these issues ourselves. Your instructions are clear, with great advise and technical "know how" to do it right. Your cutaway view makes your explanation invaluable that substantiates the do's and don'ts. You are the best at what you do, as I'm a fan
for life. Keep-up the great work MF (my friend) !!
Thank you very much!
@@Got2Learn i gotta cut the pipe to drain water out, no other way grrr..
Effortlessly explained. Attention to detail is awesome.
Thank you kindly!
You the # one my friend I fix some things in my house following you directions.
Awesome, glad I could help!
you really have a great style to your videos, very helpful and straight to the point. The more I watch the more UA-cam is recommending to me
🤩🤩🤩
Leaks happen bro, not often but once in a while. When you've completed 100's of joints it hard to gauge that odd one. Sometimes you forget to tighten that odd compression joint. I only really dry test gas lines. There's no second chances when safety is critical. Any plumber who tells you they haven't had a leak is a liar 😜.
Keep up the excellent work bruh 👌
I agree with everything you said ghost, if you don't want any leaks, don't go to work, cuz it WILL happen one day or another.
@@Got2Learn Tru dat bro, desoldered joints which a reformed are usually actually stronger. As the joint has been coated with solder (tinning).
Your videos are looking super pro bro. Really super with the editing & CGI, bravo 👌.
Thanks so much ghost! Yeah I want to do this type of editing in every video from now on, I am getting a lot of positive feedback from that, so it can only get better from now and on, :)
Ha! And always, the joint that leaks is one of the first you did, right at the back of the cupboard behind all the other pipes you've just put in! Quote from my plumbing tutor many years ago: "ALWAYS check your joints, they're like pretty women, turn your back & they are trouble.!"
@@theondebray leaks happen especially when you have apprentices on hand. We've all been there, it was us creating devastation back at the beginning. Heck, sometimes you just have one of those days when you've done an install. By the end of it you just want to get the hell out and hey presto Mr leak shows up 🤷♂️
Thank you. I don’t know if I’ll ever need to do this myself, but I take some valuable plumbing principles from here.
I used your tips yesterday with wiping the extra flus and using the tin flux you would think I was soldering for 20 years thanks for the help
Maybe the best instructional video I’ve ever watched!
Wow i'm so honored, thank you so much!!!
The way I have found to be successful with copper pipe soldering is to make sure there is no moisture in or on the outside of the pipe. Keep the joint clean and use a liberal amount of flux on every surface to be soldered. If those three things are done your solder joint will adhere no matter how ugly you solder. Remembering that the solder itself chases the heat so i apply on the separate side that I am applying the torch so it will travel throughout the joint.
If you are soldering a shutoff valve on a line with any moisture in it, make sure the valve is open. Steam in a pipe will bounce a closed valve off a ceiling. 😁
You can do it with water running out through the hole. You just have to add the solder or you may use a welder and just tack bunch above the area that needs to be repaired. You also will need a grinder so you may grind the "weld" downwards over the leaky area. Obviously if you have a large enough hole you won't be able to do it with running water. Hope you learned something today. Err, hope it helps someone in the future.
I recently found your channel. I enjoy how your videos are packed with actual information and knowledge on the actual subject.
Thank you for sharing
Welcome aboard and thank you so much for your kind comment Victor, really appreciate it :)
as a journeyman plumber I approve this channel
Lovely, thanks so much buddy!
A little waxing with some flex seal. Dab of silicone aced out
Again, great video. I'm sure you have the best channel for plumbers right now. Great information, visual examples of right and wrong . Amazing. Dont stop making these. Go from tips on grounds to fixtures! That's 100+ videos . Where I work if we glued a PVC fitting 1 1/2" + . No matter how long if needed due to mistake . We use our torch to burn/soften, to peel it out. It works great to even re use. But idk if there are consequences using the method.
Hey man, thank you so much for you're comments, they keep me going. As for the PVC removal trick, I made a video about a month ago that talks "just" about this, here's the link if you wanna see it: ua-cam.com/video/UPzUBxvB8jo/v-deo.html