Honda Rancher, Foreman, Rubicon Topend rebuild 2014+ | Smoking
Вставка
- Опубліковано 16 лис 2020
- Just a quick video I threw together on how to rebuild your topend on any 2014-2021 Honda rancher, foreman, or rubicon.
let me know if this video was helpful. you you have any questions please send me a DM on instagram and I will get back with you.
@vesselpowersports
@
don't forget to like and subscribe! - Розваги
Lots of critics on here, I’ve built prob 50-60 Honda engines, and most of my builds have been aftermarket upper kits, and my boys ride them to death, no smoke, no rattled, carry on bro
Do yk where I could get a top end kit for a 2021 Honda TRX520FE2 Foreman 4x4 ES EPS
Explained very well
Great videos man
Thanks!
What’s the link to the top end for a 2018 honda rancher 420 wanna make sure I’m getting the fright one
I pushed my piston in and it won’t come out how do I get it out again I want to take the c clips out but can’t get the piston back up
Looking for a rebuild kit for 2016 rubicon. With the jug. Any leads
Did it work good?
do you have to put the piston top dead center before you put the valve cover on
Personally I would so it’s just easier but because this has lifters and not and overhead cam I’d say no
How did you set the rings like the orientation of the rings
The manual says 33 degrees of each other
Why didn’t you set the motor to top dead center before adjusting valves
That’s the proper way, but it’s how I used to do it on my old Datsun, and just have always continued like this
@@vesselpowersports gotcha I was just wondering because I’ve always been told to get it to top dead center and then adjust…we’ll i guess I just learned something new
When I tried doing mine the crank spun and piston dropped.. what would cause that?
What do you mean dropped? Piston moves with the crank
How much does a top end rebuilt cost on a Honda 2019 rancher 420 ? What should I pay
$200 in parts, Cheap if you can do it yourself!
@@vesselpowersports where you recommend getting a top end from
1st
Are these OEM parts or aftermarket?
aftermarket
What kind of exhaust is that
HMF
Great video, very informative but damn bro do you even believe in Torque specs. I cringed 😬 the whole time you were sending it with the impact. And you put way to much trust in them ring specs in that china kit. But again over all very informative.
The rings need to be properly gapped and orientated correctly.
How many hours or miles will this top end rebuild need to happen on these 420's or does something else dictate it ??
All about your riding , I have 34,000 miles 2014 rancher 420 hard miles in rural Alaska kids beating the hell out of it , wide open ice road trips. And just now it’s starting to lose compression and the front end it tanked !!
@@sgtXsasquatchX yup, i have a 2017 rancher 420 with about 32,000 miles which i put in by myself and i do wide open throttle for going though snow and muds still running strong.
and i live on the coast of alaska western coast
Where did you buy the top end kit?
eBay!
No Torque Wrench = No Bueno
After about 15-20 topends you get used to it. My torque wrench only goes down to 50lbs so I have to rent one
Hondaboats torque is 29 pounds
Honda and even the cheap-o aftermarket ring kits have a dot or a letter on the end of the ring end gap that indicates 'UP' on both upper compression rights. You should make a note of this
because the rings are minutely shaped differently. Be sure to check next time. And.... what's with all these u-tubers spraying gasket goop on Honda gaskets? Was there goop on the gasket
when you tore it apart? NO. Why do you think it needs goop on reassembly? Oh.... I get it.... cuz you went cheap-o and bought some knock off from China.