2 meter ANYHOW J-pole ANYHOW antenna EMT conduit

Поділитися
Вставка
  • Опубліковано 22 січ 2022
  • 2 meter J-pole antenna REBUILD. 1/2" EMT conduit/galvanized steel
    Big shoutout to KG5NUB for helping me recreate the intro scene. Check out his channel also / @kg5nub
    You can also support this content through Patreon / redneckhamradio
  • Навчання та стиль

КОМЕНТАРІ • 15

  • @philparrish6914
    @philparrish6914 Рік тому +1

    PVC pipe with 12AWG copper wire inside works great.

  • @rohnkd4hct260
    @rohnkd4hct260 2 роки тому +1

    J-Pole is a good antenna. made one with old 300 ohm TV lead in. Worked quite well.

  • @RedNeckSurgeyTech
    @RedNeckSurgeyTech 2 роки тому +1

    Very nice! Always want to make a J- pole. I've only made dipoles for 20 and 40. I will make a J- pole this spring. 73 from KF0ALT

  • @jlacy8234
    @jlacy8234 2 роки тому +1

    That is great. I have a copper one but need a second and am going to build one like this.

  • @Henryham-g8tmh
    @Henryham-g8tmh 2 роки тому +1

    Thanks for ya time. Certainly looking forward to your vids. Hope all goes well for ya.
    73
    G8TMH

  • @terryadams8012
    @terryadams8012 2 роки тому +1

    Thanks for the video. Very interesting. How did you connect the SO-239 on the antenna to receive the coax?

    • @RedNeckHamRadio
      @RedNeckHamRadio  2 роки тому +1

      I soldered wire to the center pin of the connector and then used a short piece of #12 solid copper wire from the case of the panel mount so239 with #6 x 32 screw and nut. I drilled holes at the feed point of the antenna and used #6 x32 screws and wingnuts to connect the wires that I had attached to the connector, The solid wire helped to keep the connector rigid. If that makes any sense.

  • @rwpugh0975
    @rwpugh0975 2 роки тому +1

    Hi really like your videos. Simple and down to earth, just what we need. I have an idea for another one, make one on how you have the studio mic attached to your system and how you key up and make it all work. Thanks and 73, KC3TBV,

    • @RedNeckHamRadio
      @RedNeckHamRadio  2 роки тому +1

      Yep thanks. That sounds like a good video to come.

  • @ducktapepilot
    @ducktapepilot 2 роки тому +1

    That's pretty cool! Just curious, would this also work from 70cm band?

    • @RedNeckHamRadio
      @RedNeckHamRadio  2 роки тому +1

      The one I built here isn't resonant on the 70cm band but I'm sure one can be built that is.

    • @BryanTorok
      @BryanTorok 2 роки тому +3

      It is possible to make a J-Pole that has a decent SWR on both 2M & 70CM. However, in general, the maximum take off angle will not be toward the horizon but about 40 degrees up from the horizon. That will cost you about 3 to 6 dB at the horizon. Now, that is not as bad as it sounds and may still be OK for working local repeater and mobiles. There is a person on here who has plans for a dual-band and even tri-band J-Pole that has a good SWR and take off angles. If I can find it again, I'll come back here and edit this comment.

    • @ducktapepilot
      @ducktapepilot 2 роки тому

      @@BryanTorok Ok that would be great, thank you!