@@RichardLucas I can't imagine using one of these boats in open sea, that leaves bays lakes and rivers, the domain of pontoon boats. The only requirement that would be better served by these is small size. Oh and speed.
As long as overlapping joints of the plastic sheets are facing towards the back of the boat and the seams are sealed with a waterproof silicone adhesive... the boat should last quite a long time.
Что то грызут меня сомненья что все эти соединения при помощи гвоздей будут достаточно хорошо держать , особенно в полу лодки когда люди начнут туда наступать изнутри давя на пластик рядом с деревом
Now reinforce the outside of the hull with fiberglass for rigidity and sealing all the leaks that will come up when the mechanical resistance of the water roughens up and thins the plastic. The workmanship was good... But there is a best practice to making anything that floats on the water that significantly reduces the potential for accidents and/or failures in the material/construction.
My neighbor who was a brainiac made a catamaran using oil drums halves back when they didn't have plastic drums. He put them 4ea long ways and brazed them together Then added copper tubing over it. He reinforced the hull by also bridging it with copper tubing. When he was done he sprayed the bottom a lot of coats as he did with the inside. He put an aluminum wave shield in the front. He put a 20hp motor on the starboard side as he operated it on the port side. The first trial checked out but it was completely under powered. So he kept increasing the Hp until the boat balance out. Eventually heard it sank due to an retaliation for stealing someone's girlfriend.
ধন্যবাদ ওস্তাদজীকে আমি ১৯৯৪/৯৫ সাধু যোসেপ কারিগরী শিক্ষা গ্রহণ করেছি লেদ মেশিনে প্রশিক্ষণ নিয়েছি এখও এ কাজে নিয়োযিত আছি আপনার কাজে প্রসংশা করি খুবই চমৎকার হাতের কাজ আপনার।
Ładny projekt łodzi! Ta, wykonana przez ciebie jest fajna ale wykonana wg. mnie dopiero w połowie. Brakuje przede wszystkim podłogi oraz zabudowy burt od środka. Bez zabudowy podłogi, stanięcie nogą na dnie łodzi grozi po prostu jej rozerwaniem i zatonięciem! Pozdrawiam
That's a pretty awesome build. I don't know how we expected that not to leak. I think I put a roll of butyl and some stainless screws in. Let's go fishin!!
It is better to weld the seams using a soldering iron and pieces of plastic. Polyethylene terephthalate should be welded. Or you can seal them with silicone sealant. Well, or spend 5-10 bucks on one or two layers of fiberglass, and also make a deck from the same plastic to make it easier to remove water, and add weight to the bottom to make it harder to turn over while standing on the water..
This is pretty cool, not sure how safe these boats are compared to boats created in traditional materials such as various fibber or just wooden boats. I can imagine these are ok on rivers, but how does that plastic handle sea water? Also I think an improvement would be to use a heated wire cutter to cut plastic or a similar tool. And recycle the scraps too. Using a saw creates a lot of plastic dust, which is both bad for environment and everyone else, while also being very bad for the worker(s). Of course, just reusing the barrel for their original purpose would be an even better use.
On peut faire un bateau avec a peu prés tous type de matériaux, il faut tenir compte de la résistance, du poids et de la facilité a mettre en œuvre. le gars fait avec ce qu'il a sous la main, des barils en plastiques, mais disons-le clairement ce n'est surement pas la meilleure solution, la fibre de verre, le bois ou l'alu seront évidement bien préférable plus durable et fiable! bravo tout de même pour le travail et la patience! Je vois tout de même un inconvénient majeur sur cette réalisation, indépendamment de l’étanchéité qui pourrait être moins bonne a longue échéance, il n'y a aucun fond de sol rigide et si on pose les pieds sur les ptastiques en dehors des longerons de bois, il y a fort a parier qu'on pourrait passer a travers ou affaiblir l'assemblage.
Excellent travail simple et moins cher je note 20/20 , j'aimerais bien si quelqu'un peut transmettre ça à nos frères en Afrique .Le bois augmente de prix.
Мужик молодец, рукастый. Однако инженерная составляющая слабовата- у лодки нет единого жёсткого каркаса, а потому вся конструкция получилась хлипкой, и для нормального использования не пригодной
Ignorant me from 10-15 years ago would have loved this video more. If you're not collecting the micro plastics as you cut the barrels you're just creating micro waste that will end up in our water. I agree with recycling and the reuse of materials but I also believe in making sure that your take care of each step from start to finish. I'd rather him use only wood as it's reusable and not as harmful to the environment instead of plastic but what can you do? If you Google the state you're in asking how much micro plastics are in our drinking water you'll understand why I don't agree with the use of plastics. In my state, 69 tests were done all over the state and there was an average of 13 micro plastics in each test. That's a test tube, a very tiny vial, if you think about a bottle of water and how much you're drinking from those, it's just gonna get worse with more and more people having untreatable cancer. I love the boat build, the guy is creative and did a tremendous job on it, but I have different views on it as I've grown older and more wise. Love the build, good job.
@@ВладимирДавыденко-ь8ю бочка у нас стоит 200💲еще за доставку 🚚 нужно будет заплатить минимум 400💲 . Чтоб лотку сделать нужно 4 бочки . Теперь сложите четыре раза по двести и плюс четыреста за доставку . Листы ПНД три метра длиной и шириной полтора метра . Цена примерно 300 долларов . Нужно примерно три листа , доставка из магазина до подъезда бесплатно .
I think your boat needs an inner shell as a floor cover. In fact, the body should be two layers.
HDPE can be weded with hot air gun and is guaranteed 100%waterproof. With the nails sooner or later water enters
아주 멋진 배 입니다. 저라면 플라스틱과 목재 사이에 고무 타이어 조각을 넣어 밀봉을 할것 같습니다....
While good work the best use of these barrels is in pontoon boats.
They're great for floating docks too.
@@vertstang123 Good point.
@@RichardLucas Obviously not the best pontoons but best use of these drums in boat form. Sealed cells that for the most part just need mounting.
@@RichardLucas I can't imagine using one of these boats in open sea, that leaves bays lakes and rivers, the domain of pontoon boats. The only requirement that would be better served by these is small size. Oh and speed.
The best: Straw for storing brandy
So did you just steal this guy's video and narrate over it?
I really don't think that butt jointing the wooden frames and nailing some plastic patches on will last very long.
Как обработать, минимум 10 лет может прослужить
水の抵抗の恐ろしさを知らぬ…愚か者だよ…
Butt joining would then leave you dependent upon the strength of the wood splitting so he likely lapped the panels which would be very strong.
As long as overlapping joints of the plastic sheets are facing towards the back of the boat and the seams are sealed with a waterproof silicone adhesive... the boat should last quite a long time.
Nails? Agreed!
В следующий раз сделайте и говна и палок!
Что то грызут меня сомненья что все эти соединения при помощи гвоздей будут достаточно хорошо держать , особенно в полу лодки когда люди начнут туда наступать изнутри давя на пластик рядом с деревом
Economiquement intéressant ,mais le problème c'est que rien ne colle sur le polyéthylène , donc pas facile de faire l'étanchéité !
That's why it welds together. A soldering iron will help. Well, epoxy resin, as well as polyurethane, PUR.
Remember how plastic water pipes are connected)
Goose wasn't bothered by the guy sawing right next to it.
It was trying to get out of there - 1:33. It was distracting from the boat build.
Now reinforce the outside of the hull with fiberglass for rigidity and sealing all the leaks that will come up when the mechanical resistance of the water roughens up and thins the plastic.
The workmanship was good... But there is a best practice to making anything that floats on the water that significantly reduces the potential for accidents and/or failures in the material/construction.
Fibreglass over barrel plastic would delaminate. The barrels with sealant would be monocoque by themselves. Avoid over-engineering
It defeat the purpose of making this a cheap and easy project tho
Good luck making anything stick to polyethylene.
@@peternicholsonu6090 Varela are pvc? Both polyester and resin grab that.....
@@linusgoblinthis is far from cheap. Barrels are pricy and this won't last. So.. pointless
Pang ilog lang..MAHINA DI MATIBAY...KULANG SA MGA SUPORTA.. DI ANGKOP SA KARAGATAN..BAWAL DAPAT ITO WALANG SAFETY
My neighbor who was a brainiac made a catamaran using oil drums halves back when they didn't have plastic drums. He put them 4ea long ways and brazed them together Then added copper tubing over it. He reinforced the hull by also bridging it with copper tubing. When he was done he sprayed the bottom a lot of coats as he did with the inside. He put an aluminum wave shield in the front. He put a 20hp motor on the starboard side as he operated it on the port side. The first trial checked out but it was completely under powered. So he kept increasing the Hp until the boat balance out. Eventually heard it sank due to an retaliation for stealing someone's girlfriend.
A Ship!! Lmfao 😂
It's a canoe! 8hp way over kill for that with a flimsy transom!
Crazy and dangerous!
Wouldn't take it offshore or out of sight of land. Always wear a life vest.
More work than necessary. I would have made a couple of pontoons, built a frame and structure on top. Mounted a motor and been on my way.
Recycling isn't using working barrels :D
техника безопасности почти нет . обтекаемость очень слабая.слишком лёгкая на развороте перевернётся.
ไม่ทนทานเป็นมลพิษต่อสิ่งแวดล้ม
I think you need to make original content instead of stealing views from other creators.
слишком легкая, такие манёвры могут привести к перевороту, надо делать тяжелее.
На коленке, из говна и палок, Человек делает настоящую лодку лодку!
E tutto bello ma secondo me in italia non puoi metterla in acqua la legge quà fa schifo tutto vietato senza la normativa cee
Did not see any waterproofing did not see any silicon it would leak water.
Y quebnonfiltre aguaby se unda esta rarobeso
ধন্যবাদ ওস্তাদজীকে আমি ১৯৯৪/৯৫ সাধু যোসেপ কারিগরী শিক্ষা গ্রহণ করেছি লেদ মেশিনে প্রশিক্ষণ নিয়েছি এখও এ কাজে নিয়োযিত আছি আপনার কাজে প্রসংশা করি খুবই চমৎকার হাতের কাজ আপনার।
No deck inside? I'd probably step right through the hull... With all those tacks, this would be for calm, fresh water lakes only!
Ładny projekt łodzi! Ta, wykonana przez ciebie jest fajna ale wykonana wg. mnie dopiero w połowie. Brakuje przede wszystkim podłogi oraz zabudowy burt od środka. Bez zabudowy podłogi, stanięcie nogą na dnie łodzi grozi po prostu jej rozerwaniem i zatonięciem!
Pozdrawiam
...and it creates microplastics with the saw blade cutting through the plastic.
That's a pretty awesome build. I don't know how we expected that not to leak. I think I put a roll of butyl and some stainless screws in. Let's go fishin!!
Jika rumahku dekat pantai pasti kubuat
الترجمة تحجب المشاهدة
It is better to weld the seams using a soldering iron and pieces of plastic. Polyethylene terephthalate should be welded. Or you can seal them with silicone sealant. Well, or spend 5-10 bucks on one or two layers of fiberglass, and also make a deck from the same plastic to make it easier to remove water, and add weight to the bottom to make it harder to turn over while standing on the water..
İskelet sağlam olmazsa bogulursun reis...
That barrel he had in the front was full of water, the boat is too light for that motor and was trimming up way too high.
Very good job I likeit
whats wrong with screws instead of nails?
Bare minimum is ring shank nails. No way I'm risking my life with 1000 little tacks
Everyone has not been on a boat at some point in their life. you are extremely privileged.
This is pretty cool, not sure how safe these boats are compared to boats created in traditional materials such as various fibber or just wooden boats. I can imagine these are ok on rivers, but how does that plastic handle sea water? Also I think an improvement would be to use a heated wire cutter to cut plastic or a similar tool. And recycle the scraps too.
Using a saw creates a lot of plastic dust, which is both bad for environment and everyone else, while also being very bad for the worker(s).
Of course, just reusing the barrel for their original purpose would be an even better use.
Greetings coming from Indonesia, healthy greetings and creative greetings
SUPER IDEA . POZDRAWIAM .
ボートの強度の基本となる龍骨から造るのでは無く…被覆する船体の形状に合わせて内殻を端材で釘打ちして防水塗料を薄く手塗りする…手の込んだ船外機付き手桶…命がいくつあっても足らんわ!!!まぁ池で水遊びするくらいなら趣味としてアリカモね!!
外洋に出たらお陀仏物件
by 沈水艦
Ich sehe nur Mikroplastik
Como proceder para ver experiment nav egabilidade de um desses barcos?
help the environment by recycling (uses only new barrels) lol
Кажется в стыках не совсем герметично , или " все лодки текут - знай себе вычёрпывай " . Не мне плавать на ней .
On peut faire un bateau avec a peu prés tous type de matériaux, il faut tenir compte de la résistance, du poids et de la facilité a mettre en œuvre.
le gars fait avec ce qu'il a sous la main, des barils en plastiques, mais disons-le clairement ce n'est surement pas la meilleure solution, la fibre de verre, le bois ou l'alu seront évidement bien préférable plus durable et fiable! bravo tout de même pour le travail et la patience!
Je vois tout de même un inconvénient majeur sur cette réalisation, indépendamment de l’étanchéité qui pourrait être moins bonne a longue échéance,
il n'y a aucun fond de sol rigide et si on pose les pieds sur les ptastiques en dehors des longerons de bois, il y a fort a parier qu'on pourrait passer a travers ou affaiblir l'assemblage.
最多玩幾日,隻船肯定自己解體!成隻船嘅結構只不過比模型船好少少!但模型船吾會坐人!😲😲😲希望佢自己用好啦,吾好害人😐😐😐😐😐😐!
I saw this video from its original owner :-(
Excellent travail simple et moins cher je note 20/20 , j'aimerais bien si quelqu'un peut transmettre ça à nos frères en Afrique .Le bois augmente de prix.
HELAL OLSUN. Çök güzel.
Hadir nyimak salam kenal dari kisaran city Asahan Sumut Indonesia 🇮🇩🇮🇩
eso no tiene la categoría de barco. Es un objeto flotante.
You need a helper
Genial!!.😅
Yeah yeah, but shop duck! SHOP DUCK!
ich Liebe auch diese PE Tonnen daraus kann man viel Machen unkaputtbar
Norm for river
Araújo caiaque do Brasil
Nicely done! The difficulty is all the woodwork to get a solid wooden frame.
Amazing tanks perkonsian nya cukup sempal best k
how does this not leak?
1:00 I'm glad i'm not the only goose watching this!
De eenvoudige Indonesiers was al lang begonnen
Out koek.😅En 😅
최고 멋진 보트제작영상
잘보고 구독하고 응원하고갑니다
최고십니다
접합부들 틈 사이로 물이 안 세게 하는 방법은 안 나오네. 가장 중요한 과정인데 ㅎ
Cheaper to just buy a boat . Here in Tampa used plastic barrels are $100 each
Hahaha 20 here!😂
Thanks for sharing sir Godbless
Deffo fit for purpose 😊
👍🏴😁✌️
Мужик молодец, рукастый. Однако инженерная составляющая слабовата- у лодки нет единого жёсткого каркаса, а потому вся конструкция получилась хлипкой, и для нормального использования не пригодной
плюс не раскрыт вопрос водонепроницаемости
Love it . Looks easy enought. Built a few boats out of plywood, this looks great.
wow very nice lake
Need some fiberglass now
Ignorant me from 10-15 years ago would have loved this video more. If you're not collecting the micro plastics as you cut the barrels you're just creating micro waste that will end up in our water. I agree with recycling and the reuse of materials but I also believe in making sure that your take care of each step from start to finish. I'd rather him use only wood as it's reusable and not as harmful to the environment instead of plastic but what can you do? If you Google the state you're in asking how much micro plastics are in our drinking water you'll understand why I don't agree with the use of plastics. In my state, 69 tests were done all over the state and there was an average of 13 micro plastics in each test. That's a test tube, a very tiny vial, if you think about a bottle of water and how much you're drinking from those, it's just gonna get worse with more and more people having untreatable cancer. I love the boat build, the guy is creative and did a tremendous job on it, but I have different views on it as I've grown older and more wise. Love the build, good job.
1:32 "Here the design is completely optional", I can translate- "NO design" ))).
not a ship it's a boat
Excellent effort , viewing from Detroit Michigan USA 🇺🇸
Benar berarti bagus😂🎉
ทำไมใต้ท้องเรือพวกข้อต่อพลาสติกไม่ต้องยาอย่างนี้รั่วแน่ๆชุ่ยมาก
working w ducks
What about the Kill Cord?
why nails?
Я тебя слепила из того что было🤣
Keep up the good work ...love making...
👍 excelente y éxitos
Дешевле купить ПНД , чем бочку бу .
1 бочка это лист 1.6 Х0.8 цена 10 долл . 1 лист ПНД 8мм в 5 раз дороже
@@ВладимирДавыденко-ь8ю бочка у нас стоит 200💲еще за доставку 🚚 нужно будет заплатить минимум 400💲 . Чтоб лотку сделать нужно 4 бочки . Теперь сложите четыре раза по двести и плюс четыреста за доставку . Листы ПНД три метра длиной и шириной полтора метра . Цена примерно 300 долларов . Нужно примерно три листа , доставка из магазина до подъезда бесплатно .
So how did he really seal that PP?
with spit
Verry nice
Intelligent
wow... good job.
Very nice!
Прочно ли это?
So creative. Fantastic.
Nice boat
Cool 😊
Genio
Hay lắm xin cám ơn bạn
Your first statement is a lie, not everyone has been on a boat!
Super
Amazing very nice boat making