BKS Creative is a UA-cam channel where you'll find a passionate boat builder sharing his journey of crafting boats and showcasing unique welding projects. ua-cam.com/channels/CbK1K762Au9A2r_-J673Fw.html
Awesome job!! A very useful addition to this build would be to enclose the fan chasis entirely with additional chicken wire to keep debris from being pulled into the fan and protect the blades from damage plus to protect from personal injury by the moving motor parts.
Rubber wedges should have been placed under the engine connection bolts. The engine, which was placed on a poor quality platform, became even more dangerous with vibrations.
@@galleria100fuegocuidadsate4 probably so. I'm sure there is a proper technical term for the wire used on chicken coops but where I live we layman just refer to it as chicken wire.
The blue print is contained in brain of that talented man. The satisfied grin on his face upon completion and trials is what makes this video so precious to me. Give the man a brick and he will build a mansion.
I love these kinds of builds. Great stuff. I build a lot of fishing canoes in West Africa myself. All the polyester used on this project won't last long in the water. With only one air chamber, the polyester will start rotting from condensation. A small leak between layers and the boat will sink. We always foam the inside to make it unsinkable.
@MrGentlebutfirm, please be aware that the material deteriorates rapidly once delamination begins in saltwater. While it may not completely dissolve, it will disintegrate. Fortunately, repairs are part of our company's services.
@@ewaldmaas5790 Please explain the break down steps more carefully, so I get your message! Why would the laminate be prone to delamination? Polyester even - and epoxy too are rather water resistant. So what is so bad about condensation?
Small boats made of polyester are built in layers. These boats usually have a wooden construction covered with polyester. If the first layers are damaged, water will seep into the layers. Polyester also doesn't do well in hot environments because it's not very flexible. In a factory setting, a boat is made entirely of polyester in a controlled environment, so the results are much different. But even then, it doesn't like West Africa very much. Epoxy works better but is very expensive. We only use it for certain repairs and protective topcoats.
@@AVZNANIYA --- да при наличии опыта и на малых реках катаются на таких -- просто винт должен быть закрытый сеткой.. иначе поскользнулся и придется вышей родне икать вашу голову на дне водоема ...
Seorang pria yang membangun perahu DIY dari awal hingga akhir menggunakan fiberglass dan kawat jaring menunjukkan betapa kreativitas dan ketekunan dapat menghasilkan karya yang luar biasa. Mulai dari perencanaan desain hingga proses konstruksi yang teliti, proyek ini menantang tetapi juga sangat memuaskan. Dengan bahan-bahan yang relatif sederhana, ia berhasil menciptakan perahu yang tidak hanya fungsional tetapi juga memiliki daya tahan tinggi, membuktikan bahwa impian membuat perahu sendiri bisa menjadi kenyataan dengan dedikasi dan keterampilan yang tepat.
They live in a world where stupid people get punish. If you are dump enough to swim around a propeller, you will be punish for being stupid. Only people that grows in such a location would understand.
Only the mass production can GRANT the minimum use of resources. Congratulations for your hability to reproduce complex structures with simple materials.
Pretty cool Some ideas -- based upon my needs. This builder did great on his. Stuff the pontoon tubes with plastic soda pop bottles. It will provide bouyancy in case of a puncture. Each two liter bottle provides 4 pounds of bouyancy. Also if you can - baffle the pontoons into three compartments for same reason. I was impressed with the propellor making and set up - but i could utilize a standard outboard motor better. Simply reinforce the stern board and a backing plate. It also provides greater internal space. That would simplify the entire build. Id use marine wood as stringers for mor comfortable flooring. Perhaps internal width to match standard flotation boat cushions. You could epoxy in lifting points for a crane hoist... and also add in mountings for a bimini top. Im wondering how many layers would be necessary for rough waters. I could see a thin layer one breaking up in waves. All in all nice build!
Thank you for sending me this wonderful video, my dear friend. I enjoy these techniques, which are wonderful and very beautiful. This innovative thing is also my hobby. Thank you very much, my dear brother.
DIY dari awal hingga akhir menggunakan fiberglass dan kawat jaring menunjukkan betapa kreativitas dan ketekunan dapat menghasilkan karya yang luar biasa. Mulai dari perencanaan desain hingga proses konstruksi yang teliti, proyek ini menantang tetapi juga sangat memuaskan. Dengan bahan-bahan yang relatif sederhana, ia berhasil menciptakan perahu yang tidak hanya fungsional tetapi juga memiliki daya tahan tinggi, membuktikan bahwa impian membuat perahu sendiri bisa menjadi kenyataan dengan dedikasi dan keterampilan yang tepat.
Вообщем к многим узлам и ко всему есть вопроси, как то он много колхозил во время работы, можно было получше сделать если би он мозгы включал бы, но видно что не особо деньги в мужика водятся даже на такое, но не плохо получилось даже красавчик
А ничего, что закон Архимеда не так работает?😂 такая форма нужна для жёсткости надувной конструкции, если конструкция не надувная - бред сивой кобылы. Огромный полезный объем судна потерян, а дополнительная масса приобретена. 😂😂😂
@@ЕвгенийКаравайкин-п1я где вы здесь узрели Архимеда, остроумный вы наш? Вы вообще в курсе какое отношение закон Архимеда имеет к форме предмета? Или вы это ещё не проходили?
@@СергейМельников-ц3е закон Архимеда позволяет судну держаться на воде, это раз, как он работает вы не знаете, это два)))надувать или чем-то наполнять жесткую конструкцию не нужно, а вы видимо абсолютно не умный раз не смогли уловить суть моего коментария
Sei stato davvero bravissimo a costruire questa imbarcazione. Complimenti davvero. Se posso darti un consiglio mettiti una rete di protezione attorno all' elica perché è molto pericolosa quando funziona, così eviti che tu o qualcun'altro vi facciate male in modo molto grave. Un caro saluto dall' Italia con affetto Mauro.❤
Guauuuu, que maravilla de trabajo que ha echo este muchacho, lastima que en España no nos dejen hacerlo, lo haría encantado. Una magnífica barca para salir de pesca
É fantástico ver a criatividade do ser humano. Como descrever a sensação de criar algo do nada e depois desfrutar do trabalho realizado. Deve ser incrível! 🤨
В каком месте молодец? Мне, как инженеру-конструктору больно на это смотреть. Ни образования, ни элементарных знаний. Винт сделан на глазок. Вы лично, что-нибудь слышали о профиле винта? А как реализовать его точное исполнение в домашних условиях? Человек построил из говна и палок. И я надеюсь, что это его не убьёт и не покалечит. Защитной решётки нет. Крепление конструкции вызывает сомнения. А ещё я как дипломированный материаловед могу сказать о том, что стекловолокно очень специфичный материал. Не терпит воздуха между слоями. Соответственно без вакуумной установки не обойтись. И ещё не терпит переменные нагрузки и вибрацию. Трещины пойдут. А потом винт, а он толкающий, упадёт на этого самоделки на и порубит на куски. Начиная с головы.
Such a fun project and great job !! When I realized he was building an airboat,I had had big doubts for several reasons.Upon completion, and for what he is building,I think this is a superior build (small) but more stable than the airboats we used in the Florida Everglades.The lower center of gravity is a MAJOR plus.He def needs to cover that prop cage.A small piece of hard debri will make that wooden prop explode into deadly splinters. I think its brilliant tho.
The smartest thing that should be on everyone's mind right now should be to invest in different streams of income that are not dependent on the government. Especially with the current economic crisis around the world. This is still a good time to invest in gold, silver, and digital currencies (BTC ETH...)
BKS Creative is a UA-cam channel where you'll find a passionate boat builder sharing his journey of crafting boats and showcasing unique welding projects. ua-cam.com/channels/CbK1K762Au9A2r_-J673Fw.html
❤❤❤❤❤
جيد لكنه يحتاج لدراسة اكثر لان فيه نقاط ضعف
و ين حصل لالياف وهاي الماده لصنع زوارق
Why are you stealing others video
Excellent job! Just would like to see more layers on the bottom with some reinforcement material to protect from rocks.
My exact thoughts while watching. The whole thing could use an extra layer or two
bonne idée mais dans des conditions écologiques déplorables en 2024
@patrikcalloch7953 Yes, however, he could have used the wire mesh there as well or left the wood attached 🤷♂️
A capacidade do homem persistente leva a criar suas próprias imaginação.
Parabéns 😊😊
Awesome job!! A very useful addition to this build would be to enclose the fan chasis entirely with additional chicken wire to keep debris from being pulled into the fan and protect the blades from damage plus to protect from personal injury by the moving motor parts.
Och
Rubber wedges should have been placed under the engine connection bolts. The engine, which was placed on a poor quality platform, became even more dangerous with vibrations.
you meant chicken mesh?
@@galleria100fuegocuidadsate4 probably so. I'm sure there is a proper technical term for the wire used on chicken coops but where I live we layman just refer to it as chicken wire.
Главное создателя этого чуда не выпускать дальше этой речки.
Вроде визуально всё классно, но по сути это карточный домик, который не терпит деформаций
شكراً لك انت عبقري
فكرة جميلة جدا وغير مكلفة
من يعرف إسم للسلك الدي إستخدم
The blue print is contained in brain of that talented man.
The satisfied grin on his face upon completion and trials is what makes this video so precious to me.
Give the man a brick and he will build a mansion.
theres alot of clever people in this world and brother you are one of them
I love these kinds of builds. Great stuff. I build a lot of fishing canoes in West Africa myself. All the polyester used on this project won't last long in the water. With only one air chamber, the polyester will start rotting from condensation. A small leak between layers and the boat will sink. We always foam the inside to make it unsinkable.
They used epoxy not polyester
Polyester does not rot!
@MrGentlebutfirm, please be aware that the material deteriorates rapidly once delamination begins in saltwater. While it may not completely dissolve, it will disintegrate. Fortunately, repairs are part of our company's services.
@@ewaldmaas5790 Please explain the break down steps more carefully, so I get your message! Why would the laminate be prone to delamination? Polyester even - and epoxy too are rather water resistant. So what is so bad about condensation?
Small boats made of polyester are built in layers. These boats usually have a wooden construction covered with polyester. If the first layers are damaged, water will seep into the layers. Polyester also doesn't do well in hot environments because it's not very flexible. In a factory setting, a boat is made entirely of polyester in a controlled environment, so the results are much different. But even then, it doesn't like West Africa very much. Epoxy works better but is very expensive. We only use it for certain repairs and protective topcoats.
Absolutely brilliant. High level of ingenuity.
Brilliant idea!! Hand crafted with minimal materials and cost! Labor intensive but very satisfying when completed! Kudos to a job well done! 👍
Слава Создателю , за таких прекрасных и способных людей , которые делятся дарами вышних! Всем благ на пути познания)
хороший рыбакакос получился --- адская мясорубка. ....
@@VasiliyBogdanovich2022 нормально)) на открытой воде можно зажечь по полной))
@@AVZNANIYA --- да при наличии опыта и на малых реках катаются на таких -- просто винт должен быть закрытый сеткой.. иначе поскользнулся и придется вышей родне икать вашу голову на дне водоема ...
@@VasiliyBogdanovich2022 сам факт технологии , забытое , старое)))) думаю доработают))
@@AVZNANIYA -- ну не знаю у нас в Восточной Сибири таких полным полно, на них по малым горным рекам на рыбалку и охоту народ передвигается ...
Seorang pria yang membangun perahu DIY dari awal hingga akhir menggunakan fiberglass dan kawat jaring menunjukkan betapa kreativitas dan ketekunan dapat menghasilkan karya yang luar biasa. Mulai dari perencanaan desain hingga proses konstruksi yang teliti, proyek ini menantang tetapi juga sangat memuaskan. Dengan bahan-bahan yang relatif sederhana, ia berhasil menciptakan perahu yang tidak hanya fungsional tetapi juga memiliki daya tahan tinggi, membuktikan bahwa impian membuat perahu sendiri bisa menjadi kenyataan dengan dedikasi dan keterampilan yang tepat.
harga berapa ketemu nya
FANTASTICO JOB CONGRATULATION JOINVILLE BRAZIL
보면서 대단하다는 말이 몇번이나 하게 됩니다.🎉🎉
bonne idée mais dans des conditions écologiques déplorables en 2024
I am truly impressed at how awesome that came out. I'll be without the motor that thing was light as a feather! BRAVO!!!!!!
Well done.
Please make a safety cage around the propeller.
*Дно тоже следовало бы усилить. Случаи всякие бывают.*
They live in a world where stupid people get punish. If you are dump enough to swim around a propeller, you will be punish for being stupid. Only people that grows in such a location would understand.
@@kkutube1972 zyja w swiecie minimalnych ograniczen ! im, nie potrzebne sa pasy by przejsc na druga strone...(jak tobie) balwanie...
IMPRESSIVE !!!!! 👍👍👍👍👍
This would be the idle boat for a cruise on the river.
Well done.
Only the mass production can GRANT the minimum use of resources.
Congratulations for your hability to reproduce complex structures with simple materials.
Pretty cool
Some ideas -- based upon my needs. This builder did great on his.
Stuff the pontoon tubes with plastic soda pop bottles. It will provide bouyancy in case of a puncture. Each two liter bottle provides 4 pounds of bouyancy.
Also if you can - baffle the pontoons into three compartments for same reason.
I was impressed with the propellor making and set up - but i could utilize a standard outboard motor better. Simply reinforce the stern board and a backing plate. It also provides greater internal space. That would simplify the entire build.
Id use marine wood as stringers for mor comfortable flooring. Perhaps internal width to match standard flotation boat cushions.
You could epoxy in lifting points for a crane hoist... and also add in mountings for a bimini top.
Im wondering how many layers would be necessary for rough waters. I could see a thin layer one breaking up in waves.
All in all nice build!
Muito legal, parabéns pela engenhosidade.
What a hard work he does for us
Verdadeira obra de arte
Excelente profissional
Ótimo vídeo 💯👍
Bravissimo, sei il TOP 1
МОЛОДЕС🇷🇺😎👍🇷🇺😎👍🇷🇺😎👍❤❤❤
3 screws holding that fan mount at the rear is a death wish.
Excelente!!!!La necesidad es la madre de toda inventiva y creación
.
The man that create that DIY boat was really a genius? Amazing?I love that stuff!!! 😍😍😍❤❤❤👍👍👍😊😊😊
Excellent!
Thank you for sending me this wonderful video, my dear friend. I enjoy these techniques, which are wonderful and very beautiful. This innovative thing is also my hobby. Thank you very much, my dear brother.
very good work!
Grand problème de résistance structure pour la liaison des flotteur avec l'ensemble de bateau et de l'habitacle du bateau
Bot
bonne idée mais dans des conditions écologiques déplorables en 2024
Wow great job 😮😮
Very Impressed !
now , let's watch it Sink Extremely quickly!!!!
Hi. Do use a mosk to prevent acetone inhalation. FANTASTIC.
You are a trooper professional sir. I love your work. I think you did a fantastic job.
Fantastic! Thanks for making this epic tutorial and sharing your skills and knowledge! Love the boat! Peace to the World 🙏 🏴 🇬🇧
DIY dari awal hingga akhir menggunakan fiberglass dan kawat jaring menunjukkan betapa kreativitas dan ketekunan dapat menghasilkan karya yang luar biasa. Mulai dari perencanaan desain hingga proses konstruksi yang teliti, proyek ini menantang tetapi juga sangat memuaskan. Dengan bahan-bahan yang relatif sederhana, ia berhasil menciptakan perahu yang tidak hanya fungsional tetapi juga memiliki daya tahan tinggi, membuktikan bahwa impian membuat perahu sendiri bisa menjadi kenyataan dengan dedikasi dan keterampilan yang tepat.
Cool boat
Лодка лёгкая и наверно быстрая, но если бы труба была заполнена пенопластовой крошкой или каким нибудь вспененым материалом вроде было бы надёжнее.
Вообщем к многим узлам и ко всему есть вопроси, как то он много колхозил во время работы, можно было получше сделать если би он мозгы включал бы, но видно что не особо деньги в мужика водятся даже на такое, но не плохо получилось даже красавчик
А ничего, что закон Архимеда не так работает?😂 такая форма нужна для жёсткости надувной конструкции, если конструкция не надувная - бред сивой кобылы. Огромный полезный объем судна потерян, а дополнительная масса приобретена. 😂😂😂
@@ЕвгенийКаравайкин-п1я где вы здесь узрели Архимеда, остроумный вы наш? Вы вообще в курсе какое отношение закон Архимеда имеет к форме предмета? Или вы это ещё не проходили?
@@СергейМельников-ц3е закон Архимеда позволяет судну держаться на воде, это раз, как он работает вы не знаете, это два)))надувать или чем-то наполнять жесткую конструкцию не нужно, а вы видимо абсолютно не умный раз не смогли уловить суть моего коментария
Ну да😂
와우, 저도 좀 만들어 줘요~
Sei stato davvero bravissimo a costruire questa imbarcazione. Complimenti davvero. Se posso darti un consiglio mettiti una rete di protezione attorno all' elica perché è molto pericolosa quando funziona, così eviti che tu o qualcun'altro vi facciate male in modo molto grave. Un caro saluto dall' Italia con affetto Mauro.❤
You are a master of ingenuity
Absolutely well done.
Sensacional parabéns 👏👏👏
Absolutely brilliant!
Hats off to your dedication , improvisation and hard work. Dont stop here buddy..Do keep the safety tips and suggestions in mind. take care
Guauuuu, que maravilla de trabajo que ha echo este muchacho, lastima que en España no nos dejen hacerlo, lo haría encantado. Una magnífica barca para salir de pesca
É fantástico ver a criatividade do ser humano.
Como descrever a sensação de criar algo do nada e depois desfrutar do trabalho realizado.
Deve ser incrível! 🤨
Great little project. 👌
Experts among the people
Thank you
nice job and surprised not using a roller 😎😎
Nice job
Гений. Молодец. Не ноет сам все сделал. Мужик
хороший рыбакакос получился --- адская мясорубка. ....
там только музыка . .и если ноет то по китайски ...
bonne idée mais dans des conditions écologiques déplorables en 2024
В каком месте молодец? Мне, как инженеру-конструктору больно на это смотреть. Ни образования, ни элементарных знаний. Винт сделан на глазок. Вы лично, что-нибудь слышали о профиле винта? А как реализовать его точное исполнение в домашних условиях?
Человек построил из говна и палок. И я надеюсь, что это его не убьёт и не покалечит.
Защитной решётки нет. Крепление конструкции вызывает сомнения. А ещё я как дипломированный материаловед могу сказать о том, что стекловолокно очень специфичный материал. Не терпит воздуха между слоями. Соответственно без вакуумной установки не обойтись. И ещё не терпит переменные нагрузки и вибрацию. Трещины пойдут. А потом винт, а он толкающий, упадёт на этого самоделки на и порубит на куски. Начиная с головы.
OUTSTANDING!
Ne yetenekli insanlar var.
Wonderfull and creative work👏
Awsome diy
Great job 👍
Mantap ni kepingin juga buat untuk mancing nanti
Awesome job.
Great job perfect😊
Это потрясающе!
Amazing my friend❤
Nice boat you are very talented
Gotta love the no glove technic😮
Шикарная лодка😮
Молодец руки растут от куда надо как говорится начало есть , будет и по круче ложка. 👍👍👍
Руки из жопы растут. Знаний на нуле.
Great job
La verdad te felicito, sos un genio, bendiciones!!!
The best channel 👍
Such a fun project and great job !! When I realized he was building an airboat,I had had big doubts for several reasons.Upon completion, and for what he is building,I think this is a superior build (small) but more stable than the airboats we used in the Florida Everglades.The lower center of gravity is a MAJOR plus.He def needs to cover that prop cage.A small piece of hard debri will make that wooden prop explode into deadly splinters. I think its brilliant tho.
Very easy method very useful method. Many thanks for the idea
Молодец!
Impressive work, it looks fun too.👍
Very good you can do it
Potresti insegnare all' accademia degli artigiani bravo complimenti
EXCELLENCE
Молоток! Нет. Кувалда!!!
That's cool
👍👍👍 ile wyszło żywicy na wszystko ?🤔
Здорово😊🤝
Muito criativo, faltou colocar tela na carenagem de proteção da hélice por segurança
Master👍
Thank you for uploading the video😮 that looks like fun building
Wow... Keren banget
Ein wahrer Künstler wow
cool boat!!
Love it
I'm carving out some wooden propellers now!
Awesome build from start to finish, love it bro 👍👍
Великолепно!!!!!!!!
Very talented sir, great video. Enjoy your homemade boat 😎🤘
The smartest thing that should be on everyone's mind right now should be to invest in different streams of income that are not dependent on the government. Especially with the current economic crisis around the world.
This is still a good time to invest in gold, silver, and digital currencies (BTC ETH...)
A lot of people still make massive profit from the crypto market, all you really need is a relevant information and some professional advice.
No I don't trade on my own anymore always required help and assistance
From my personal financial advisor
YES!!! That's exactly her name (Mrs Jenny ) so many people have recommended highly about her and am just starting with her from Brisbane Australia 🇦🇺
I'm surprised that this name is being mentioned here, I stumbled upon one of her clients testimony on CNBC news last week
Excelente
Thanks
Magnifique ....🎈
Awesome job very impressed thank you for sharing
Very good work. Süper project. Thankyou.
Chapeau l artiste
Parabens , magnific
Шедевр!!!
Terbaik bang terus kan