Thank you for making the addition of controls to the VFD so easy to understand. I have looked at a number of videos and most talk about alot of BS and not the practical part of adding the VFD to an existing machine.
Hi can you please help i have a cross cut saw and need to put in a two way switch so that i can have it running continuously or on the hand button stop&start also i need to put in an emergency stop
Sorry, but it wrong be wrong to give out 'how to' advice on wiring machines up especially safety circuits, I would recommend you consult a qualified electrician to assist you in this. As I state on my channel information and in my videos this is how I do things and professional advice should always be sought.
I bought an start & stop button all in one but before i connect potenciometer and reverse direction 3 button 1-0-2 But if i want use specific button i must to connect a bridge from this one reverse control to start & stop to activate?
The manufacturers instructions aren't very clear and show the wiring connections the wrong way round. You will need a wire from the COM to both switches, either from the VFD or bridged from the switches. Then run a separate wire from each switch, START/STOP to X4 and Forward/Reverse to X6. X4 will need to be programmed as I show at around 1:30. X6 is already programmed by the manufacturer so you shouldn't need to change anything on the VFD. If you look at the picture at 2:11 you can see the wires I have connected. RED/BROWN from COM to switches. WHITE for START/STOP and Green for FORWARD/REVERSE. BLACK, BLUE and YELLOW are for the potentiometer. Hope this helps.
One question - can you program the XSY-AT1 VFD Variable Frequency Drive so that it runs at high speed for about 2-3 minutes at the beginning, but closer to fixed low speed?
Thank you for making the addition of controls to the VFD so easy to understand. I have looked at a number of videos and most talk about alot of BS and not the practical part of adding the VFD to an existing machine.
Glad it was helpful!
Great 👍 please can you show ke how connect Star and stop in the panel ?🙏
Hi can you please help i have a cross cut saw and need to put in a two way switch so that i can have it running continuously or on the hand button stop&start also i need to put in an emergency stop
Sorry, but it wrong be wrong to give out 'how to' advice on wiring machines up especially safety circuits, I would recommend you consult a qualified electrician to assist you in this.
As I state on my channel information and in my videos this is how I do things and professional advice should always be sought.
I bought an start & stop button all in one but before i connect potenciometer and reverse direction 3 button 1-0-2
But if i want use specific button i must to connect a bridge from this one reverse control to start & stop to activate?
The manufacturers instructions aren't very clear and show the wiring connections the wrong way round. You will need a wire from the COM to both switches, either from the VFD or bridged from the switches.
Then run a separate wire from each switch, START/STOP to X4 and Forward/Reverse to X6.
X4 will need to be programmed as I show at around 1:30.
X6 is already programmed by the manufacturer so you shouldn't need to change anything on the VFD.
If you look at the picture at 2:11 you can see the wires I have connected. RED/BROWN from COM to switches. WHITE for START/STOP and Green for FORWARD/REVERSE.
BLACK, BLUE and YELLOW are for the potentiometer.
Hope this helps.
One question - can you program the XSY-AT1 VFD Variable Frequency Drive
so that it runs at high speed for about 2-3 minutes at the beginning, but closer to fixed low speed?
I don’t think this unit has that flexibility as there’s no timer on the system.
What fault FC002?
Please
Looks like under voltage. Your supply voltage is too low.
@@bodganeering cant change display coz setting unfungction?
I would suggest contacting the manufacturer.
Hickle Viaduct