Installing Fox 2.5 DSC and Camburg Control Arms on 3rd Gen Toyota Tundra (2022-2024)
Вставка
- Опубліковано 7 лют 2025
- I try to create entertaining and knowledgeable videos for your entertainment! I am a car enthusiast building and learning along the way! If you enjoyed this video click the “like” button and Subscribe for more! Plenty of humor, car installs, events, and interesting car videos to come!
Find some of the parts I use:
runnin4tacos.com/
Instagram: @tommylinebarger
TikTok: @tommylinebarger
Just installed ICON 3. Coilovers and their UCA. Did it by watching your video and instruction by Icon. My only problem is now I have a gearshift stock in park unless I use the little pressure switch by the shifter. Going to have to take it to the dealer to erase the codes. Thx for the video.
Oh no! That’s odd for that to trigger.
@@TommyLinebarger I OBDII code reader is finding anytthing, so going to head over to Toyota Monday. But again thanks for showing an easier way of doing it.
@clarencemckimmy9437 glad it was helpful!
@@TommyLinebarger it was a short in a wire, they just got the parts in and hopefully it will be fixed on the 9th
@clarencemckimmy9437 that’s not too bad then
Great job, man!
For the rear coil spring is it a 2 inch or 1inch?
On the rear did you change the… brake lines and did you use the fox rear suspension that’s for 2 to 3 inches of lift?
Just installed kings and UCAs. My dash is now lit up with warning lights. I replaced the abs lines. Took it to the dealer for recalibration and ADAS. Still have lights. Any help would be appreciated! Thanks
Are the rear dobinsons springs the c59-843VB ? rated for 220-440lbs? How do you like it with the gfc topper? Does it ride stiff?
How much?
I had a very similar build on my third GEN tundra did you use the factory coil sleeves on your Dobinson coils?
@@davidboris313 Dobinson I believe
you truck looks great ..i do have a question what is your total height from the ground to the top of the shark antenna.. i want to lift it but want to keep it in the garage. thanks in advance
It’s about 7’ 1”
@@TommyLinebarger thank you
Looks great, how difficult was the UCA to do, getting ready to install Icon 3’’ lift with their UCA’s?
They weren’t hard as long as you remove the stuff under the hood to remove the bolt
I just installed my. But I get rubbing on the sway bar. Only at full lock. Like a u turn. With the same tires as you. Do you get any..?
Hmm that’s odd. Common places to run are the cab mount, the block behind the fender well, and the fender extensions. Never heard the sway bar. Maybe get a new alignment and check your wheel offset. I’m running a 0 and want to go down to around a +10
@ my set up is 17x8.5 +10. But put 37. Toyo rat trails. Great set up. Just I bit in full lock turn Man. And I think your is 35.?
How do you like it. I’m installing mine tomorrow
It’s awesome! Glad I waited
Hey Tommy, How is the ride? I have icons and they are super stiff. Thanks
They're extremely comfortable and responsive to bumps and obstacles.
What dsc settings are you running? I drove mine around for a week and the ride seemed okay but finally adjusted them and found both high and low speed were wide open at softest setting. Bumped it up three clicks on both and still testing it out. Haven’t gone off road, 95% will be on road without much cargo myself
I think I’m running around the same. 3 clicks on high speed and I think 4 on low speed
Which rear spring height and rate did you go with? I thought you mentioned it in the video but couldn’t find it
Hey I went with a 200 pound springs from Dobinson. I probably should’ve gone with the 100 though
@@TommyLinebargerwhat’s the difference in ride or is it not as noticeable? New to all of this, TYIA!! Truck looks great btw