AEG Lavamat Turbo Protex L75480WD - Faulty Heating Element

Поділитися
Вставка
  • Опубліковано 23 сер 2024
  • This is the error message you will get if the water heating element is faulty - in our case, it was covered in limescale and needed to be replaced.
    Hopefully this helps you diagnose your problem.

КОМЕНТАРІ • 20

  • @derinteknolojiler471
    @derinteknolojiler471 3 місяці тому

    Hi guys, if your aeg/Electrolux/zanussi heat pump dryer is running 30 minutes normally and then giving e60 (e63 in test mode) just checked the upper capasitor which should be 10uf. You will see it is around 4.5 - 5.0 that is a fault.. I finally solved it. Just replace the 10uf capasitor (the above one, connected to engine motor), no soldering or antything, it is plug and play. Buy it from an electronic market showing the old faulty one, do not buy it from an AEG or other brand shoppers. Otherwise it will be 10 times expensive. There is space to place it into the machine,, so the new one can be a little fat or long, no matter, just be carefull for the values like voltage etc. They are not polarized so you can attach the 2 cables whatever you want. You don't need to disassebly tumble or any thing. Just get the back top and right panel, you will see the 10uf capasitor lying horizontally. Fyi, the below one is 18uf and you need to diassemble tumble and other things to get it back, but fourtunately you can measure it without disassemble.

  • @johnmelling9950
    @johnmelling9950 7 місяців тому

    Very helpful thanks. Mines doing exactly the same with error code E66. I removed the heater element and its full of limescale and lots of rust. I ordered a new element so hopefully that will fix it.

    • @theliberalthug
      @theliberalthug  7 місяців тому +1

      I'm glad it helped! We had huge amounts of faff identifying this, so I hope it helped save you a lot of bother.

  • @washersfan9003
    @washersfan9003 4 місяці тому

    Hi! I'm dealing with an e57 error code! I'm litteraly in the same situation, can I ask if you remember how you managed to unlock the door? I've my laundry blocked inside for 2 days....I feel like crying :(

  • @mehtapoktay2523
    @mehtapoktay2523 6 місяців тому

    Hallo, here is the AEG Lavamat Turbotrocknungsmaschine. Ständig kam Wasser aus dem Ventil, ich habe das Ventil gewechselt. We've never started, we've stopped wasting time. Es trocknet

  • @ildaeni7783
    @ildaeni7783 7 місяців тому

    hi i have the same dryer it starts normally i mean it was working normally until now but now it starts and starts and dries a few minutes later it shows me E 60 in the program it seemed the minutes and it makes a noise like the one the dryer ends the drying

    • @theliberalthug
      @theliberalthug  7 місяців тому

      This is a combined washer dryer, not just a dryer.

  • @anland506
    @anland506 4 роки тому

    how did you resolve this problem with AEG? we have the same problem

    • @theliberalthug
      @theliberalthug  4 роки тому +2

      Hello. So after much mucking around with non-AEG engineers we got an AEG guy from a company called RSL. It's a simple problem - the water heating element was completely encased in limescale, so the machine automatically earths and shuts down as it can't run. Took him 10-20 mins to resolve.

    • @adriancraddock3337
      @adriancraddock3337 4 роки тому +2

      @@theliberalthug Thank you for posting this, I too have the same problem did you have to replace the heater element or did clean it?

    • @theliberalthug
      @theliberalthug  3 роки тому

      @@adriancraddock3337 the engineer replaced the heating element, it was totally covered in limescale after about 2-3 years use in a hard water area (London)

  • @joycegabriela8863
    @joycegabriela8863 Рік тому

    How to solve this problem please?

    • @theliberalthug
      @theliberalthug  Рік тому

      Please see comments below:
      Hello. So after much mucking around with non-AEG engineers we got an AEG guy from a company called RSL. It's a simple problem - the water heating element was completely encased in limescale, so the machine automatically earths and shuts down as it can't run. Took him 10-20 mins to resolve.

  • @lukaskanci2932
    @lukaskanci2932 8 місяців тому

    Is it o n child lock

    • @theliberalthug
      @theliberalthug  8 місяців тому

      No, the issue is the heating element is corroded with limescale and needs to be replaced. It is a fundamental fault with a core component at the end of it's life span, this is not a user interface problem.

  • @user-du2fq9jp2f
    @user-du2fq9jp2f 2 роки тому

    هل يمكنك مساعدتي ؟

  • @jeannedehaart7793
    @jeannedehaart7793 3 роки тому

    Bbc