@@GuilhermeBarroso sorry it's ok I whent back over ur last messages u sent me and I'm doing it now I have a bad crash and it all messed up but now I can get it by ur last message u sent me thanks and sorry for bottering u have a good day
It depends on a lot of environmental factors, bud... It was about 11 degrees, but I live at 600m AMSL. Try to add as much as you can without blowing the tail and bogging the engine too much
When I get 0 on middle stick it ends up full stick at 0.65 and when I adjust it to 11.5 and go to middle again I don't get 0 y what is it I'm doing wrong 😭
@@kevingoldbey7401 HDE mechanics are kinda a pain in the but, don't beat yourself rs Start from top , then move your way to the bottom. Put your swashplate about midrange, and adjust the linkages until you get 0 degrees at the blades. Put your collective at 50%, remove the horn from the servo, reinstall in a way you get 0 degrees again. Adjust the link between the servo and the elevator as required, you may also use subtrim
Bom dia Guildy tenho um trex 700 nitro com 3gx e um trex 550 com 3g essa unidade é confortável ou vc acha que tenho que trocar pois onde moro não tenho com quem trocar ideia
Hello. Do you have a video on aligning flybar blades and swash plate?
Top, muito bem explicado obrigado, Adelson de ES
Relíquia esse aí...
Show esse brinquedo hein!
Muito brabo esses hélis a combustão,
Grande vontade de um dia entrar nesse mundo!
(😅heli so tive elétrico kkk)
Bom dia mestre, esse alicate e bem multi funcional kkkkk.brincadeira muita experiência hein!
😅🤣🤣 Até tinha comentado na filmagem que existe um alicate para isso, mas eu não tinha pois raramente preciso rs
Hey man what u use to make the battery pack u have on ur heli to work have u a regulator on it if so what kind
Fala migo,blz? Boa tarde,por acaso vc sabe configurar o sitema kds flymentor num 450 flybar?
Amigo buen video quiero comprar un raptor 50 me lo recomendarías en 2023 por el tema repuestos y demás o no habría problema??
Yes... really hard to find parts. I would not have one as my "daily"
Hello Im the user of raptor 50 in korea. How do you get some parts of raptor?
Hi mate what should I set full pitch at and low pitch at I have the middle at zero
Again?!
@@GuilhermeBarroso sorry it's ok I whent back over ur last messages u sent me and I'm doing it now I have a bad crash and it all messed up but now I can get it by ur last message u sent me thanks and sorry for bottering u have a good day
@@kevingoldbey7401 No problem, mate. Let me know if you have any issue
What have u set ur pitch at mate is it 12.00 dagreas
It depends on a lot of environmental factors, bud... It was about 11 degrees, but I live at 600m AMSL. Try to add as much as you can without blowing the tail and bogging the engine too much
It will also depend on what blades you are using, RPM, etc... 11 degrees is a good start, then its kinda trial and error
It is also normal to have more negative pitch than positive to keep the same climb ratio. Don't keep yourself stuck at 11/-11
I have mine bang on 11 up and 11 down now it flys lovly no bogging thanks for ur help cause I was way out I had it way over on 16 digress
No I won't man I am on 7degreas up and down now
BOA TARDE GUILDY , ESTOU NA DÚVIDA FAVOR MIN ENFORMA, UN SERVO TRAVA CALDA DA KDS PARA HELICÓPTERO ELÉTRICO CLASSE 450 FLYBAR, GRATO PELA COMPREENSÃO
hola sabes si hay alguna corona principal compatible con el
Not that I'm aware of
Olá amigo, você é do RJ? Estou precisando de uma ajuda para voar novamente.
Sou do interior do Rio, são José do vale
What have u got for full pitch on the gage
It is a narrow disk, you may start with 11.5 and then adjust
Hey man everytime I set it to full pitch to 12 I can't get mid stick to 0 can u tell me what I'm doing wrong
When I get 0 on middle stick it ends up full stick at 0.65 and when I adjust it to 11.5 and go to middle again I don't get 0 y what is it I'm doing wrong 😭
@@kevingoldbey7401 HDE mechanics are kinda a pain in the but, don't beat yourself rs
Start from top , then move your way to the bottom. Put your swashplate about midrange, and adjust the linkages until you get 0 degrees at the blades. Put your collective at 50%, remove the horn from the servo, reinstall in a way you get 0 degrees again. Adjust the link between the servo and the elevator as required, you may also use subtrim
@@GuilhermeBarroso thank u so much mate for ur help we don't have a model shop here in Ireland were I'm from it's redickless lol
Hey man what u have ur blade pitch set at
Check my replies to you ;]
Can u tell me what is the pitch on the pitch gage from middle is zero high and low is what
Ur reply didint tell me what it should be like man
@@kevingoldbey7401 I precisely told you that and how to get to the right values
Thank u so much man have a good day stay safe
Bom dia Guildy tenho um trex 700 nitro com 3gx e um trex 550 com 3g essa unidade é confortável ou vc acha que tenho que trocar pois onde moro não tenho com quem trocar ideia
Fala brother
Se estiver funcionando bem, não tem porque mexer.
Abraço!
Valeu obrigado
Up and down
Kamecaze kkkkkkkkkk