Hey good to see your video, I've got the 56TH in 177 and had it apart a few times, the front trigger screw can be left tight and the attached metal part comes away with the stock, also remove both circlips on the cocking arm and remove it completely, the cocking bar can then be swung forward, being careful not to turn it (marker pen handy) then cable tie into place against the barrel, using tape or a piece of rag to prevent scratches while you work. tip, remove stock and scope from the bench! much more room to use and no need for plastic containers and putting bits on shelves above. I've currently got a Vortek kit in mine with a custom spring in it, laser accurate and touching 19ftlbs, very flat shooting with JSB heavies.
I've had all the HW rifles over the years, my favourite one's the 77 and the 97, and the TXs engineering on them are so good, these don't look as well engineered, and have heard reports of them breaking on the cocking lever.
La Diana 54 Air King para ser la de gama alta sus materiales son nefactos, la palancas de carga se suelen doblar, a partes de que la base donde viene el sistema de disparo la tapa trasera y el punto de miras son de plástico llamado polímero sintético. Al igual que la 460 mágnum la palanca de carga se rompe con frecuencia
If you put a tune kit in, as a comparison, please select another non-Vortek brand... And please can you compare each rifle’s accuracy with best pellets with groups on paper targets say 20-30 yards so we can see individual performance more definitively. Thank you.
Hello, I'm a new 177 Airking owner and would like to ask a couple of questions. Firstly I removed the rear sight and installed a scope. I'm wondering if there is a spring or ball bearing under the center of the rear sight because there are recesses and I heard something drop just as I lifted the sight off the receiver. Secondly, pellets fit very loosely in the breach and one pellet fell out of the breach when I held the rifle vertical before closing the cocking arm. Any comments would be appreciated, Thanks.
Haven’t taken my gun apart for over a year now but I do believe there is a small spring which puts pressure on the plate allowing you to adjust the up or down by turning the adjustment wheel. I also lost my spring when I adjusted the sight to high. As far as loose pellets , you have to be careful with that because if you’re not looking it may fall out when you return the caulking leaver causing a dry fire. I also did that. I find the 10.5 gr Crosman dome, the ones in the brown box , fit really snug and shoot very well in imy gun. I always wash these with hot water and soap, dry them and then put a little dry lube on them as have read that Crosman’s can dirty the barrel. Barracuda Match, all head sizes , have a secure fit and are also very accurate.
I'm not sure where you are in CT. I live in Rocky Hill. If you ever need help making a video, I would love to help you. I really like how you work on your guns. Wondering if you could get my hatsan edge vortex .25 shooting a little faster.. I've tried to take some my guns apart but I definitely don't have the confidence you do. Love your stuff my brother airguner!
Love your videos man. Been following a long time. Keep the videos comin. My mod. 48 is getting a little rust near the antibeartrap lever and at the barrel. Do you know of any way to remove it without damaging the blueing? Regards
Although they are in a different class, could you do a complete design and performance compare and contrast with this and an Umarex Octane Elite, for the reason that that is the only other, in production, air rifle with a ‘floating’ receiver design. I could buy the Elite (and Parrus) off you after the reviews.
Hi airgunner im new in your chanel..i realy enjoy your vídeos,thank s for sharing very interesting pcp info. I wants to install a regulator on my Hatzan AT44-10 tactical 22cal. wich one hoy recomend me..againg Thanks and keep your vídeos coming
I prefer the HUMA reg, I have 6 now and work amazing and fairly easy to install, I choose not to use LANE regulator because you need to drill a hole in the tube and you can not go back to being unregulated.... my AT44-QE LONG is set at 110 bar and I get 50 shots with 18gr JSB...
Un bonjour de France. Merci pour cette vidéo car il y en a vraiment très peu concernant ces carabines.ma diana mienne d'éjecte plus les plombs. Je vais la démonter pour trouver le problème. Votre tutoriel sera très utile. Merci
Hey
good to see your video, I've got the 56TH in 177 and had it apart a few times, the front trigger screw can be left tight and the attached metal part comes away with the stock, also remove both circlips on the cocking arm and remove it completely, the cocking bar can then be swung forward, being careful not to turn it (marker pen handy) then cable tie into place against the barrel, using tape or a piece of rag to prevent scratches while you work.
tip, remove stock and scope from the bench! much more room to use and no need for plastic containers and putting bits on shelves above.
I've currently got a Vortek kit in mine with a custom spring in it, laser accurate and touching 19ftlbs, very flat shooting with JSB heavies.
I've had all the HW rifles over the years, my favourite one's the 77 and the 97, and the TXs engineering on them are so good, these don't look as well engineered, and have heard reports of them breaking on the cocking lever.
Similar to my Diana M48..Right, essentially the same rifle. Company acquisitions / product swaps have occurred recently.
La Diana 54 Air King para ser la de gama alta sus materiales son nefactos, la palancas de carga se suelen doblar, a partes de que la base donde viene el sistema de disparo la tapa trasera y el punto de miras son de plástico llamado polímero sintético. Al igual que la 460 mágnum la palanca de carga se rompe con frecuencia
Brilliant video, I'm looking to buy a D54 how do you rate them compared to Weihrauch 97k & Air Arms TX200/Pro Sport ?
If you put a tune kit in, as a comparison, please select another non-Vortek brand... And please can you compare each rifle’s accuracy with best pellets with groups on paper targets say 20-30 yards so we can see individual performance more definitively. Thank you.
Hello, I'm a new 177 Airking owner and would like to ask a couple of questions. Firstly I removed the rear sight and installed a scope. I'm wondering if there is a spring or ball bearing under the center of the rear sight because there are recesses and I heard something drop just as I lifted the sight off the receiver. Secondly, pellets fit very loosely in the breach and one pellet fell out of the breach when I held the rifle vertical before closing the cocking arm. Any comments would be appreciated, Thanks.
Haven’t taken my gun apart for over a year now but I do believe there is a small spring which puts pressure on the plate allowing you to adjust the up or down by turning the adjustment wheel. I also lost my spring when I adjusted the sight to high. As far as loose pellets , you have to be careful with that because if you’re not looking it may fall out when you return the caulking leaver causing a dry fire. I also did that. I find the 10.5 gr Crosman dome, the ones in the brown box , fit really snug and shoot very well in imy gun. I always wash these with hot water and soap, dry them and then put a little dry lube on them as have read that Crosman’s can dirty the barrel. Barracuda Match, all head sizes , have a secure fit and are also very accurate.
Buenos días, con que kit se puede pasar de potencia fac a 16j en calibre 22 , agradezco opinión
Good vid
I'm not sure where you are in CT. I live in Rocky Hill. If you ever need help making a video, I would love to help you. I really like how you work on your guns. Wondering if you could get my hatsan edge vortex .25 shooting a little faster.. I've tried to take some my guns apart but I definitely don't have the confidence you do. Love your stuff my brother airguner!
hello i'm from spain and i would like to know if the bar (black ) form inside the recharging bar can be repalced or can bie buyed apart
That’s a good video !
What size clamp is that ? Ty
Bent charging handle on airking. Do you know where I can send for repair in usa
Does the 54 have a longer stroke than the 48? And please compare 54 spring to original 48 spring.
my diana 54 piston is not good how i can make it good piston pin come out
Love your videos man. Been following a long time. Keep the videos comin. My mod. 48 is getting a little rust near the antibeartrap lever and at the barrel. Do you know of any way to remove it without damaging the blueing? Regards
Although they are in a different class, could you do a complete design and performance compare and contrast with this and an Umarex Octane Elite, for the reason that that is the only other, in production, air rifle with a ‘floating’ receiver design. I could buy the Elite (and Parrus) off you after the reviews.
Hi airgunner im new in your chanel..i realy enjoy your vídeos,thank s for sharing very interesting pcp info. I wants to install a regulator on my Hatzan AT44-10 tactical 22cal. wich one hoy recomend me..againg Thanks and keep your vídeos coming
I prefer the HUMA reg, I have 6 now and work amazing and fairly easy to install, I choose not to use LANE regulator because you need to drill a hole in the tube and you can not go back to being unregulated.... my AT44-QE LONG is set at 110 bar and I get 50 shots with 18gr JSB...
@@airgunnersedge4061 oh nice 50 shuts with 18 gr...and whats the fps tune speed in your hatsan to shut 18gr. Couse i have the same gr. Pellets
Un bonjour de France.
Merci pour cette vidéo car il y en a vraiment très peu concernant ces carabines.ma diana mienne d'éjecte plus les plombs.
Je vais la démonter pour trouver le problème.
Votre tutoriel sera très utile.
Merci
Where is an RWS54 maintenance video for 100 & 1000 shot?
Is it possible to replace the .22 spring piston with the .177 nitro piston?
The main spring and all other internal parts are the same on both caliber rifles.
Hey man, what's going on? Where are you?
Hi if your in CT does your company need any help I'm in Tolland, and enjoy your videos, thanks
Where is the second part?
And part 2?
Too bad i never see someone replace the breech seal or barrel seal partnumber 19/19a on the diana drawn.
Were you are airguners...¿¿ USA ??
Yes
Las tx 200 y weihrauch son superiores en materiales y acabados, a la dianas 54
دوربین میدادی یکی فیلم بگیره من که چیزی نمی بینم😢😢😢