I purchased a set of o-rings for my 2022 raw 1000x from the distributor in Texas( I received 12 packets of two o-rings in each packet and 12 differant #'s on each packet ) my question is how can I tell what o-ring goes where? ) Please Help!!
Wow you seem very knowledgeable on these guns. I am very new to tuning guns and such. I hope to do competition shooting one day. I have a raw hm 1000x .30cal. It’s two years old with no upkeep pretty much. I was shooting sub moa groups at 100-150 yards. My air rifle fell about four or fiv feet to wood floor and broke the stock. I re fastened the stock as best I could but ever since my shot groups have been large and it was shooting at 900fps. I have been trying to get my shot groups better to wut they were before the fall. I removed the regulator and turned it down and adjusted my hammer spring to be about in the middle and I’m shooting at 845-870 fps. Those are my averages from 30 shots worth. A very large variation of fps. I also get about 40 shots per bottle fill. What do you think I should do or replace or clean to get back good 100 yard shot groups besides send my gun to raw to have them re tune it. I have ordered a new regulator and that’s on its way. Also I will get about five or six shots in a row that r bullseye then I get a shot that’s a few inches low then my next shot is closer to bullseye and then closer and closer till the rifle is back zeroed. It’s very strange and very frustrating that I can not figure out y this is happening. If you can help me at all it would be very appreciated and I’d be a subscriber for life
Apparently there are following possibilities; Due to drop of your gun the pellet probe has got a bit missalligened and causing variation of fps due to leaking of air from there. There may be some issues with bedding of the action into the stock after you have tried to fix the broken stock. This may cause issues. There are chances that the silencer of the gun is no more properly fixed. It may has gone misaligned a bit, misaligned internal baffles etc. I would start with removing the silencer and see how it shoots. As I know regulator cannot be damaged if the gun is dropped. It's a very sturdy platform. Check all the three set screws that hold the barrel into the action I hope one of the above mentioned things might address the problem. Bhaur
The action beds into the stock normal, the brake happened on the hand grip. I will try removing the two baffles and see if it shoots better. What is the pellet probe? I will order a new one. Or should take my current pellet probe out and re install it?
Yes the pellet probe is that pushes the pellet into the barrel. Test your gun without all kind of silencer. At least you may be confident that the gun including the barrel is in good condition.
great video, thank you so much!!! this is so helpful to the RAW community.
Thank you 😊
Great videos you are a valuable asset to the raw community
Thank you so much sir
sir keep it up Surely your hard work will pay off
Thank you 😊
Thanks for another very helpful video.
Welcome
بہترین ویڈیو آپ کا شکریہ
I purchased a set of o-rings for my 2022 raw 1000x from the distributor in Texas( I received 12 packets of two o-rings in each packet and 12 differant #'s on each packet ) my question is how can I tell what o-ring goes where? ) Please Help!!
Send me your WhatsApp number, I shall share the available details
Mashallah Sir ❤️
Thank you
Thank you
Nice this video
So nice of you
Wow you seem very knowledgeable on these guns. I am very new to tuning guns and such. I hope to do competition shooting one day. I have a raw hm 1000x .30cal. It’s two years old with no upkeep pretty much. I was shooting sub moa groups at 100-150 yards. My air rifle fell about four or fiv feet to wood floor and broke the stock. I re fastened the stock as best I could but ever since my shot groups have been large and it was shooting at 900fps. I have been trying to get my shot groups better to wut they were before the fall. I removed the regulator and turned it down and adjusted my hammer spring to be about in the middle and I’m shooting at 845-870 fps. Those are my averages from 30 shots worth. A very large variation of fps. I also get about 40 shots per bottle fill. What do you think I should do or replace or clean to get back good 100 yard shot groups besides send my gun to raw to have them re tune it. I have ordered a new regulator and that’s on its way. Also I will get about five or six shots in a row that r bullseye then I get a shot that’s a few inches low then my next shot is closer to bullseye and then closer and closer till the rifle is back zeroed. It’s very strange and very frustrating that I can not figure out y this is happening. If you can help me at all it would be very appreciated and I’d be a subscriber for life
Apparently there are following possibilities;
Due to drop of your gun the pellet probe has got a bit missalligened and causing variation of fps due to leaking of air from there.
There may be some issues with bedding of the action into the stock after you have tried to fix the broken stock. This may cause issues.
There are chances that the silencer of the gun is no more properly fixed. It may has gone misaligned a bit, misaligned internal baffles etc.
I would start with removing the silencer and see how it shoots.
As I know regulator cannot be damaged if the gun is dropped.
It's a very sturdy platform.
Check all the three set screws that hold the barrel into the action
I hope one of the above mentioned things might address the problem.
Bhaur
The action beds into the stock normal, the brake happened on the hand grip. I will try removing the two baffles and see if it shoots better. What is the pellet probe? I will order a new one. Or should take my current pellet probe out and re install it?
Yes the pellet probe is that pushes the pellet into the barrel.
Test your gun without all kind of silencer.
At least you may be confident that the gun including the barrel is in good condition.
So the air to push the pellet comes out of the pellet probe?
I should just order a new pellet probe or try to re align mine?
Nice video and very informative,Could you please tell me the thread size of the bottom block blanking plug and the valve plug?!
Make a full strip down video of the raw and how to put it all back together.
If you see my RAW based videos, you will know complete procedure
Good
Thanks
Do you feel that RAW is better built than FX?
The built quality of RAW is far greater than FX. There is no comparison of built quality.
FX shines in innovation and new technology
There's nothing 'Technical' about this video.