496 Big Block Chev engine dyno

Поділитися
Вставка
  • Опубліковано 21 сер 2024
  • 496 ci Big Block Chev Vintage Circuit race boat engine on the engine dyno .
    746 hp @6500 rpm and 682 ftlb . 2 bolt gm mark 4 block with Howards 4 bolt caps, Scat forged crank, Scat H beam rods , Racetech pistons , 268 @ .050 solid roller , ported DRP rec port heads(same casting as AFR enforcers) . Edelbrock tunnel ram , twin 1050 dominators.
    Knight engines, Competition Automotive Dyno Centre.

КОМЕНТАРІ • 24

  • @user-yx4ud4tl6q
    @user-yx4ud4tl6q 8 місяців тому +2

    Heavy Chevy... sounds like heaven...

  • @kidsteach938
    @kidsteach938 7 місяців тому +1

    Runs great, sounds great! It will look great in the boat!

  • @xlr8r3VA
    @xlr8r3VA 8 місяців тому +1

    Those are some respectable numbers, great job!!!

  • @357coonan
    @357coonan 8 місяців тому +2

    that's a beast...

  • @jameslahee3658
    @jameslahee3658 8 місяців тому +1

    Nice setup

  • @cushmanphillips-oz3jx
    @cushmanphillips-oz3jx 3 місяці тому

    where the 1050s a matched pair? did you have to make alot of jetting changes ?

  • @crspcritter
    @crspcritter 8 місяців тому

    Nice 👍

  • @cushmanphillips-oz3jx
    @cushmanphillips-oz3jx 4 місяці тому

    I have a very similar combination that I’ve been running for 19 years I’m putting 2 dominators on it. Could you give me more information on compression and your carb set up?

    • @jasonjordan4672
      @jasonjordan4672  4 місяці тому

      Comp is around 10.50 to 1 , carbies are 1050 dominators

    • @cushmanphillips-oz3jx
      @cushmanphillips-oz3jx 3 місяці тому +1

      @@jasonjordan4672 i have the same intake, i have 2 1150s that are going on a 540 but I'm going to try them on my 496

    • @jasonjordan4672
      @jasonjordan4672  3 місяці тому

      @@cushmanphillips-oz3jx this is all set up in my boat now and running, im having a little trouble getting it to not fuel up and run rich in the turns, i got a bit of sorting out to do

    • @cushmanphillips-oz3jx
      @cushmanphillips-oz3jx 3 місяці тому

      @@jasonjordan4672 do you think its coming out the vents ?

    • @jasonjordan4672
      @jasonjordan4672  3 місяці тому +1

      @@cushmanphillips-oz3jx fuel coming out the vents is one theory, i was planning on using some fuel line to link the vents with a notch cut out at the top and see if that helps

  • @ripper-wrench
    @ripper-wrench 7 місяців тому

    Hydraulic roller cam?

    • @jasonjordan4672
      @jasonjordan4672  7 місяців тому +3

      Solid roller , 268 @ .050 and .780 lift with a 1.8 rocker, ive never had much luck with hydraulic rollers large enough to make decent power in big block boat engines , they just wont rpm . Small block car engines seem to work ok with a hydraulic roller

  • @hankclingingsmith8707
    @hankclingingsmith8707 7 місяців тому

    How much powa

    • @jasonjordan4672
      @jasonjordan4672  7 місяців тому

      746 hp @ 6400 and 682 fltb @ 5100

    • @dansherwood9851
      @dansherwood9851 4 місяці тому

      I need one for my 69 Camaro even if I have to give up some ponies without the high rise intake.

  • @ldnwholesale8552
    @ldnwholesale8552 8 місяців тому +1

    It will never fit in a Torana!!

    • @jasonjordan4672
      @jasonjordan4672  8 місяців тому +1

      Haha , its for my Everingham lee, but i do have another Hatch back Torana with a 454 in it, long term project .

    • @steventosi8067
      @steventosi8067 7 місяців тому

      🍻💪🏻🇦🇺💨 would bring my HZ toner some spark. 🥱 What 308💨