Just a Question. Don't you plug te led into the x3 port onto the naza itself? I don't recall plugging it into your gear channel? I might be wrong because I'm more of a naza v2 Guy.
I can see two problems here. First is, that with this wiring you can't use low battery warning on Naza (there's no power on X3 port). Second is failsafe settings. You should include failsafe switch when you set receiver's failsafe, because thete is also failsafe options on Naza (on low battery, on lost signal)
I just acquired a DJI F550 Hexacopter. Trying to bind to a JR x9503 transmitter. Normal bind procedure seems to work, but the drone does not respond to inputs. It used to be bound to a Spektrum DX9. Help please.
Hi I have a new Naza M lite and guess it V1. Can you explain about the wiring structure on both these units (if you have the brown wire on top pin on the Naza so is it on the top pin of the receiver or does it go on the bottom pin. Any clarifications will be appreciated.
can you show or tell me how to hook it up to the DX7 to my Naza Lite i have the gps to and you say i will loos one is that one i will loos one gps or return to home this is where its messing me up at is on this hook up to the receiver thanks man
Excellent video except it does not show when/how to change the "switch settings" that is used to select the GPS, ATTi &Failsafe positions plus the Home lock & Course lock positions. thanks
I have a dx6i, and i need to mix channels for this particular wiring setup. If you are not using gps, course/home lock then this will be just fine for you. I like the Dx8 cause it gives you 3 way switches and not 2 way.
J.D. Rock Can you please make a video show how to setup DX6I , I have did everything but still have problem , the LED blinking red couple of times and turn off no red no green ,please help
Seth Nicodemus that really is weird, unless you are using the wrong software version but I doubt that. It should identify the gps if you have it hooked up properly. Is the gps unit new?
J.D. Rock It is a new gps, I returned my first one because I had the same problem and this new one I got has the same problem. I cannot find a solution.
Thanks for the detailed explanation! High-quality and informative video
Just a Question. Don't you plug te led into the x3 port onto the naza itself? I don't recall plugging it into your gear channel? I might be wrong because I'm more of a naza v2 Guy.
I can see two problems here. First is, that with this wiring you can't use low battery warning on Naza (there's no power on X3 port). Second is failsafe settings. You should include failsafe switch when you set receiver's failsafe, because thete is also failsafe options on Naza (on low battery, on lost signal)
I just acquired a DJI F550 Hexacopter. Trying to bind to a JR x9503 transmitter. Normal bind procedure seems to work, but the drone does not respond to inputs. It used to be bound to a Spektrum DX9. Help please.
Hey guys I have an issue with my drone. When I throttle down the motors cut off, is this normal?
Excellent video, thanks
Hi I have a new Naza M lite and guess it V1. Can you explain about the wiring structure on both these units (if you have the brown wire on top pin on the Naza so is it on the top pin of the receiver or does it go on the bottom pin. Any clarifications will be appreciated.
Just to clarify I am using a flysky rx and tx. The rx is fs ia6b.
Same doubt did you got answers please share here
how would you power the receiver if you didnt have the LED controller ?
is the flight control enough to power the receiver?
do you know how to set up the devo 10 receiver i.e. putting in the wires and binding it.
can you show or tell me how to hook it up to the DX7 to my Naza Lite i have the gps to and you say i will loos one is that one i will loos one gps or return to home this is where its messing me up at is on this hook up to the receiver thanks man
will this work in a spectrum 9 with a orange 10
PERFECT TKS DUDE AWESOME JOB :)
Excellent video except it does not show when/how to change the "switch settings" that is used to select the GPS, ATTi &Failsafe positions plus the Home lock & Course lock positions. thanks
do you have video of tx settings?
Cool video, really helped me out. Keep it up
Thanks! It's good to hear it helped out someone.
Great video. Very informative. Thanks for sharing.
Thanks, I will try to share everything I know on RC.
Thank you for this video.
No problem, its good to hear this video helped out a couple of people :)
What this work with a DX6 G2?
I have a dx6i, and i need to mix channels for this particular wiring setup. If you are not using gps, course/home lock then this will be just fine for you. I like the Dx8 cause it gives you 3 way switches and not 2 way.
J.D. Rock Can you please make a video show how to setup DX6I , I have did everything but still have problem , the LED blinking red couple of times and turn off no red no green ,please help
thank you man!!!
My naza will not go into gps mode in the assistant software it shows atti where gps mode should be
@ 9:20, you have to adjust your remote setting so that it will switch from attitude to gps. Did you do this step?
do you mean setting end points? I have done that. It is as if i have no gps there
Seth Nicodemus that really is weird, unless you are using the wrong software version but I doubt that. It should identify the gps if you have it hooked up properly. Is the gps unit new?
J.D. Rock It is a new gps, I returned my first one because I had the same problem and this new one I got has the same problem. I cannot find a solution.
Seth Nicodemus Ok will look more into it, I am just really busy but I will try to make a video!