Unboxing IMBZBK Tempered Glass Screen Protector for Google Pixel 7 Pro - Part 1

Part 1 - Quick Unboxing IMBZBK Tempered Glass Screen Protector for Google Pixel 7 Pro.
It's an expensive kit. Hope it works!
www.amazon.com...
Check out • IMBZBK Google Pixel 7 ... for my review of the installation.

[@TofuRobots]

I just installed it. Here's my feedback. I followed the video which was helpful. I made sure my working surface was completely level, clean, and mostly dust free. Here are some observations. 1. The protective film could not be removed from the first glass screen. The pull tab ripped off, so right away 1/3 was wasted. 2. When I slowly dropped the (2nd) protector on the liquid glue, a bubble was present. I had to gently push it out. 3. The alignment tabs are very good, but not perfect. My screen installed about 1 or 2 mm low. It still covers the screen, but not perfectly vertically aligned. YMMV. 4. There was some liquid bubble pockets on the very bottom edge. You must use the UV lamp again on all four sides of the phone to completely cure the glue hard. When in the plastic holder, not all light will reach the glue. 5. The glue stinks bad.
Once complete, it looks very nice and offers better protection than without. My installation has no air pockets or bits of dust underneath. The fingerprint reader seems to work just like before the installation. I haven't re-registered my fingers. I have not turned on "screen protector mode" at this time. The selfie camera looks the same, but I'm sure the protector and glue reduce the optical clarity. I just can't tell.
Overall, I think the product is good, but too expensive. I'm not happy about 1 of 3 glass protectors being defective out of the box. Bottom line, ignoring the cost, I like the end result and feel more comfortable with the added protection to my Pixel 7 Pro.
My installation review: ua-cam.com/video/MWlXC5f3Mag/v-deo.html

[@ripdoozer]

Link to installation review video brings us right back to this video.....

[@TofuRobots]

Thanks for pointing that out! I fixed it in the description. ua-cam.com/video/MWlXC5f3Mag/v-deo.html

[@prashantgupta1908]

can you tell how's it after installation?

[@TofuRobots]

Hi, yes, I just installed it 10 minutes ago. Here's my feedback. I followed the video which was helpful. I made sure my working surface was completely level, clean, and mostly dust free. Here are some observations. 1. The protective film could not be removed from the first glass screen. The pull tab ripped off, so right away 1/3 was wasted. 2. When I slowly dropped the (2nd) protector on the liquid glue, a bubble was present. I had to gently push it out. 3. The alignment tabs are very good, but not perfect. My screen installed about 1 or 2 mm low. It still covers the screen, but not perfectly vertically aligned. YMMV. 4. There was some liquid bubble pockets on the very bottom edge. You must use the UV lamp again on all for sides of the phone to completely cure the glue hard. When in the plastic holder, not all light will reach the glue. 5. The glue stinks bad.
Once complete, it looks very nice and offers better protection than without. My installation has no air pockets or bits of dust underneath. The fingerprint reader seems to work just like before the installation. I haven't re-registered my fingers. I have not turned on "screen protector mode" at this time. The selfie camera looks the same, but I'm sure the protector and glue reduce the optical clarity. I just can't tell.
Overall, I think the product is good, but too expensive. I'm not happy about 1 of 3 glass protectors being defective out of the box. Bottom line, ignoring the cost, I like the end result and feel more comfortable with the added protection to my Pixel 7 Pro.