Lorry, just finished installing these awesome crash bars. Your product rocks. Could not be more solid. Installation was very straight forward. Write down which bolts go in what location do you don’t have to keep stopping the video during installation. Two items not in video. Right side upper mount has a wire tie mount screwed in. Clip the tire and unscrew mount. Re-tire later. On the left side you have to take off a plastic cover. One screw at bottom rear and pull out pin in front.
Just installed these on my 2019 F850GS. Additional tools required that weren't mentioned include T25 to remove the plastic cover on the LH side above the shift linkage, 8 mm socket or spanner for the M6 bolts (these should have just be M8 fasteners like the rest), and 17 mm spanner for the nut behind the M10 SHCS on the LH side. The torque for the T55 engine to frame bolts should be 100 Nm, not 47 Nm. This is a critical torque value. Overall, very happy with the quality of the bars and would purchase again, but the menagerie of different fasteners is a puzzling design philosophy.
Thank you for this comment. I installed these today and without this comment I would tighten T55 with 47Nm. I checked the torque value in service manual and it is 100Nm and the bolt is M12. This info is missing in the video.
Thanks man, i was looking for this spec, also a strange array of bolts and nuts and I’m missing the spacers. The 10x30mm also does not clear the nyloc nut. Bottom left side.
I didn't get the skittles but I did get the racks and bars within the promised delivery window! (2020 f850gs) Install was pretty straightforward. Video instructions very good. I released some of the fairing screws to accommodate the (driver's) upper right bolt, had to fiddle around with cross bar to get a proper fit, and had to release a plastic wiring harness cover on driver's left -- nothing difficult but be prepared to adjust as you go. With respect to fit and finish, the welds are decent and appear solid, the powder coat is done well, and the branded metal labels are a nice touch. My driver's upper left protrudes slightly more than the right. Unclear if this is by design or defect, but not a big deal. I tend to tip-over to left more than to right, so this will eventually even out! My request to OM would be a one-page PDF materials sheet with a list of which bolts go where. The videos are great for high-level overview, but would be a quicker install with PDF instructions sheet.
Received mine and plan on doing the install this week. They came well packed and look to be very well made. The dealer in the US also included a few stickers for my toolbox and a bag of skittles that my 14 year grabbed right away.
Great Video & Great Product. Missing from the video: 1. Left Side - remove of the black plastic panel above the quick shifter (as other mentioned) and 2. What is the torque setting for the T55 bolts? Lastly, at the mounting point next to the kick stand, the crash bar goes behind. (Was not clear enough in the video). Note that the silver color is lighter than the other silver parts of the motorcycle and different finish. I should've probably gone with black, but I'm happy I got them quickly. Thank you!!
The kit came with 2 x m10 black Allen bolts. Both had a washer and nut. What’s the purpose of the additional nut for the m10 Allen bolt? Was paranoid I had missed something. The one in the RHS goes straight into the engine block.
Me too. You did not miss anything. There is no reference to the second nut in the install video so keep it on the bike if case the installed nut ever gets lost!
Hi, I'm thinking of buying the crash bars for the F850GS (2021). are there a lot of differences between the new and older model? if so will there be a pdf installation for the 2021 model.
Just installed the crashbars last night they look nice, however the cross bar is touching the exhaust. Has anybody run into this problem and knows how to fix it? Appreciate the help
Thanks for your feedback. You’ll have to loosen the bolts on the cross brace as well as the upper crash bars. Pull the cross brace forward while retightening the bolts in order to create more clearance
Alright so. I echo some of the comments below in this. Having a video is great. But, written instructions are also necessary. I wrote my own, following the video. I'm ABOUT to put my set on, but I'm caught, concerned with a couple things. I'd love to hear some verification of the mentioned missing steps/necessary tools. And, is it critical to WAIT, and tighten EVERYTHING together at the end? I was considering installing the lower bars this weekend, and the uppers later when I have a little more time. I obviously dont want them dancing around loose in that time. Will I need to loosen them before installing the uppers?
It’d be irresponsible on our part to offer upper crash bars. There are no mounting points to support a set of upper crash bars without collapsing after one small crash. The crash bars we offer work well as per the video evidence but you can increase the protection by adding a set of decent aftermarket hand guards.
Lorry, just finished installing these awesome crash bars. Your product rocks. Could not be more solid. Installation was very straight forward. Write down which bolts go in what location do you don’t have to keep stopping the video during installation. Two items not in video. Right side upper mount has a wire tie mount screwed in. Clip the tire and unscrew mount. Re-tire later. On the left side you have to take off a plastic cover. One screw at bottom rear and pull out pin in front.
+1 these comments
Just installed these on my 2019 F850GS. Additional tools required that weren't mentioned include T25 to remove the plastic cover on the LH side above the shift linkage, 8 mm socket or spanner for the M6 bolts (these should have just be M8 fasteners like the rest), and 17 mm spanner for the nut behind the M10 SHCS on the LH side. The torque for the T55 engine to frame bolts should be 100 Nm, not 47 Nm. This is a critical torque value.
Overall, very happy with the quality of the bars and would purchase again, but the menagerie of different fasteners is a puzzling design philosophy.
Thank you for this comment. I installed these today and without this comment I would tighten T55 with 47Nm. I checked the torque value in service manual and it is 100Nm and the bolt is M12. This info is missing in the video.
@@gregorj Glad it to see it was helpful to someone, that's an important one!
Hi, just a question.. how you can remove the plastic cover on the left side? I remove the T25, but can't remove the plastic.. Thank you..
Thanks man, i was looking for this spec, also a strange array of bolts and nuts and I’m missing the spacers.
The 10x30mm also does not clear the nyloc nut. Bottom left side.
I didn't get the skittles but I did get the racks and bars within the promised delivery window!
(2020 f850gs)
Install was pretty straightforward. Video instructions very good. I released some of the fairing screws to accommodate the (driver's) upper right bolt, had to fiddle around with cross bar to get a proper fit, and had to release a plastic wiring harness cover on driver's left -- nothing difficult but be prepared to adjust as you go.
With respect to fit and finish, the welds are decent and appear solid, the powder coat is done well, and the branded metal labels are a nice touch. My driver's upper left protrudes slightly more than the right. Unclear if this is by design or defect, but not a big deal. I tend to tip-over to left more than to right, so this will eventually even out!
My request to OM would be a one-page PDF materials sheet with a list of which bolts go where. The videos are great for high-level overview, but would be a quicker install with PDF instructions sheet.
Received mine and plan on doing the install this week. They came well packed and look to be very well made. The dealer in the US also included a few stickers for my toolbox and a bag of skittles that my 14 year grabbed right away.
Just installed mine. They’re solid and beautifully finished. The video was very specific and made installation quite easy
🙌
Awesome product. Just a heads up: I believe there is a typo at 09:10 - it should be the M8x35mm bolt as shown at 10:00
Great Video & Great Product. Missing from the video: 1. Left Side - remove of the black plastic panel above the quick shifter (as other mentioned) and 2. What is the torque setting for the T55 bolts? Lastly, at the mounting point next to the kick stand, the crash bar goes behind. (Was not clear enough in the video). Note that the silver color is lighter than the other silver parts of the motorcycle and different finish. I should've probably gone with black, but I'm happy I got them quickly. Thank you!!
nice positions;. My touratechs block the panel to get at my water tank.
Do you guys recommend using any thread lock, copper grease etc on any of the bolts when installing these?
These crash bars are engine mounted, thus we don’t recommend loctite.
Hi, for the F850GS 2021(EURO5). I received a 9MM and a 5.6MM spacer, Is the 9MM for the right side?
Will them allow us to make the periodical service without removing the guards ?
Hi when you said don't use thread lock, there was threat lock on the M10 when they came out. Should I re-apply ?
Using thread lock for bolts which thread into any parts of the engine is not advised.
The kit came with 2 x m10 black Allen bolts. Both had a washer and nut. What’s the purpose of the additional nut for the m10 Allen bolt? Was paranoid I had missed something. The one in the RHS goes straight into the engine block.
Me too. You did not miss anything. There is no reference to the second nut in the install video so keep it on the bike if case the installed nut ever gets lost!
My future crash bars for my 850 GS .....
sebastien artis thank you in advance!
Hi, I'm thinking of buying the crash bars for the F850GS (2021).
are there a lot of differences between the new and older model? if so will there be a pdf installation for the 2021 model.
There’s a specific version for euro 5/2021. We only offer video installation instructions.
Hi, got mine today but no 7 & 10 mm washers with the hardware. Is that normal ?
Hello. Would you please contact our sales team? They’ll help you sort this out into at outbackmotortek dot com
How it went? Have the same issue and they responded that me my model doesnt need it... but i think it do 2023 north america
Nice work! These look awesome. Definitely a purchase for my F850GS. When might they be available in Canada 🇨🇦? Thx
Dualsport Plus in Brantford, Ontario…great customer service too
What about thread lock is it needed at all ?
Using thread lock for bolts which thread into any parts of the engine is not advised.
Just installed the crashbars last night they look nice, however the cross bar is touching the exhaust. Has anybody run into this problem and knows how to fix it? Appreciate the help
Thanks for your feedback. You’ll have to loosen the bolts on the cross brace as well as the upper crash bars. Pull the cross brace forward while retightening the bolts in order to create more clearance
Alright so. I echo some of the comments below in this. Having a video is great. But, written instructions are also necessary. I wrote my own, following the video.
I'm ABOUT to put my set on, but I'm caught, concerned with a couple things. I'd love to hear some verification of the mentioned missing steps/necessary tools. And, is it critical to WAIT, and tighten EVERYTHING together at the end?
I was considering installing the lower bars this weekend, and the uppers later when I have a little more time. I obviously dont want them dancing around loose in that time. Will I need to loosen them before installing the uppers?
@@das7101 what does that have to do with my comment?
Hi. I have the crash bar protector for the F850GS, will there be an upper crash bar protector, or is that not possible.
It’d be irresponsible on our part to offer upper crash bars. There are no mounting points to support a set of upper crash bars without collapsing after one small crash.
The crash bars we offer work well as per the video evidence but you can increase the protection by adding a set of decent aftermarket hand guards.
Hi I have replaced oem horn with Denali soundbomb compact, how can I check if crash bar doesn't meet the new denali horn?
I guess only by trying to mate the two products.
@@Outbackmotortek I'd try but there's no Outback dealer in Mexico... :(
Are these BMW OEM crash bars? You didn’t mention the manufacturer or product name/label(ie.. givi, touratech, etc...)
The crash bars are by Outback Motortek. It’s also in the video long description