DIY: G37 Oil Pan Spacer Installation Z1 Motorsports. Oil pan gasket replacement.
Вставка
- Опубліковано 20 кві 2018
- In This video, we demonstrate how to remove the engine oil pan on any VQ37VHR or VQ35HR equipped Nissan or Infiniti vehicle.
LOWER OIL PAN TORQUE SPEC: 62 inch lbs, tighten in a criss cross pattern.
OIL TUBE TORQUE SPEC: 16 ft lbs. 8 ft lbs initially, then 16 ft lbs for final tightening. IF THE BOLTS DON'T GO IN ALL THE WAY BY HAND DO NOT INSTALL THE OIL PAN SPACER UNTIL IT HAS BEEN ADJUSTED. - Авто та транспорт
Finally, a video without some young kid bouncing around yelling into the camera and explaining what the hell he is doing and why. I don't know why but watching a master ply their trade is always some how, relaxing. Can't wait to check out your other videos.
You're right on the money. Shut your mouth, stop showing your face every second, stop lecturing me and get it done.
Some entitled people here eh ?
I am not really a mechanic but when you used a wire wheel to clean the mating surface I got nervous I can only imagine a stray wire messing the motor up. I used a razor blade, gasoline, and a plastic spatula to clean mine off.
Too funny, looking up how to install the oil pan and your video popped up.
Very clean and professional job.
Subscribed.
So many people make the mistake of jamming a screwdriver in one side then prying down on it to get it off. Valve covers to. Not realizing its bending it and it'll never seal right again.
at how many foot lb did you torque it when reinstalling ?
what inch pound torque wrench are you using?
More please!
does it needs time to dry the silicone?
Where can I get the temporary studs to help with lining the spacer and pan up?
Just take a set of long m6x1.0 bolts and cut off the heads, I think that's what I did.
Did you make a mistake in the oil pan torque specs in the description . The manual says 7 to 8 foot lbs of torque.
will these bolt up to a 2013 VQ35HR MAXIMA motor, guess I'll have to crawl under the car and see if the FWD and RWD oil pans are the same...
quick question I'm also want to hook up my evt, so I need a stand alone tuner... how is the ecutek working for you... I have a 04 I35 with a 2013 VQ35HR SWAP
Anyone know what that brown sensor near the oil pan is I broke it but it still runs perfectly fine been like 7 months with it broken😅
How much more oil does the car take total after the spacer install?
A liter according to Z1
Hi there can you confirm the oil sump pan on my 2008 450GT fuga is made from steel? cheers Paul.
No sorry I don't know.
anyone know if this fits an awd g
Great video. What are you spraying on it before you wipe the mating surface?
Thanks , Brake clean was used to clean the surfaces
What product did you use to clean the surface after scrapping the RTV?
Permatex Gasket Remover Spray
or maybe it was CRC..
He used scraper, wire brush, then as mentioned, evaporative spray.
So what's the benifit of this?? Just more oil?? To add?
I had the same question
Yes, larger oil capacity and less chance of sucking in air into the oil pickup since the pickup tube goes lower.
Increase in volume means cooler temp
👍🏻
So if the oil pan is broken the car won’t run ?
oh it'll run, not for long but it will
What are the torque specs for the frames you removed?
You will need to be more specific with your question. I don’t recall removing any frames. The torque specs for the bolts I believe are 68 inch lbs and that is reviewed in the video.
What gasket maker did you use
genuine nissan silicone from the dealer
what is the name of the brown connector he’s messing with at 1:48 ? like what does it go to and what is it for?
Did you ever find out mine just got torn on the highway
@@edwinx1842 nope never figured it out, car is still working properly without it though
@@qJoooshno way😂 well couldn’t find nothing abt it online so that’s good to hear it’s working properly
I can't get at my rear cover bolts what gives
Good lord it must be nice working on a clean engine bay or newer car half of these videos are some guy with a walmart camera and an engine bay that looks like its been sitting in a swamp.
No gasket??
What is the purpose for this?
The purpose of the oil pan spacer is to a) help lower temperatures b)help extend oil life by increasing oil capacity c) update the oil pickup to include o-rings that will create a better seal for the pickup when comparted to the factory design that has no o-rings.
Enthusiast Auto Care exactly what I thought it was for so now my ? Is will it take more oil now
885.0ELopez Marijayne of course. It should need around a half quart more oil
actually it's 1qt more, measured and confirmed.
It adds 1 qt of oil capacity to the engine. Given a high dispalcement engine (stock at 328HP 7500rpm 2011+), 5qt of oil capacity cause short life of engine oil - even grade 5 sync is used, oil get dak after 5k miles ./ 6mo. Added capacity keep oil cooler and life longer. The added inch did not cause ground clearance issue, even lowered. The lowest point is the front sway bar (1.9in lower than the stock pan). The best way is to get an oil cooler (2-3x price and installation time). Plus, oil change will add a little hassle to reach the filter location.
Ты зачем это сделал?
The customer asked for it.
why not drain the oil before removing the oil pan?
I’m not sure I follow your question. The oil was already drained.
the installation of the spacer would be easier if you drain the oil from the pan before you drop the pan.
ebp609si the oil was already drained from the pan. The oil that came out in the video is just what is left that won’t come out from the drain plug.
I never would have imagined that that much oil is left in the pan after draining !
Hall Stevenson yup, that’s why when I do oil services on these I also Evac the oil after draining. Hit me up for an ecutek tune!
I bough this pice of shit oil pan spacer and is missing 2 bolts right out of the package