I think you did a great job! My only concern being a tech for 20 years is where the wire goes under the door seal I would be worried over time it would rub through and short out do you think if you took a cut off wheel and made a small relief cut so it had a pocket for it to sit in? I'm not trying to be rude by any means. Again great job
I would have soldered the wires. I have also had good service just back-probing the wires into the connector. I did that when I added extra LED lighting to the trunk.
Great video, thx. I am trying to buy one, but one site says it works with 5 V. If I connect it to the courtesy light, it will be 12 V. I’m confused… Where did you get yours..??
the extension cable DIDN’T reach? we shouldn’t have to splice any wiring (you’re awesome man, solid video!), I’ll pass. Not sure how I’d order for a 2-door M4 (2015), sure looks like more than 3 min installation
My 540 came with illuminated ones from the factory. You can’t see the cable on a factory fit so perhaps you could run it some other way. My factory ones are ‘on or off’ and don’t do the sequential display like yours. They are also a different graphic. Nice touch to the car all the same 👍
Great video. I think I would use wire taps instead of cutting the wires personally. So I've seen people install these, and almost bought them about 100 times. But I was curious how easily they get scratched up. You've had yours about 7 months. Do the plates themselves still look half decent?
Does anyone know how to actually remove the stock sill without breaking it? Every video I have found, they lever it out and break a clip or the sill where it holds the clip in place. Mine rattles and I want to fix it properly.
Great vid buddy. Having fitted mine, I found that the lights flicker when the engine is on. I'm guessing you didn't have that problem? They work fine when the engine is off
Great detail. I installed bmw holo on the door. Set of 4 on Amazon. Easy mod but great bmw holo at night. Suggest you do video on that as I wish i would have done and uploaded on here.
Here ya go. May need to check model to make sure it fits your car. I have an F10 and it looks great. Was hoping you are near area so you can assist me in doing that mod you did. Heres link: 4Pcs Car Door light Ghost Shadow Welcome Light Logo Projector Accessories Courtesy Step Lights For BMW X5 E70 E90 E60 E87 F20 E92 E91 E61 F11 F18 E63 E64 F12 E65 X1 X3 X6 GT 3 5 6 7 X GT Series www.amazon.com/dp/B082DBS5Y7/ref=cm_sw_r_cp_api_i_emqdFbD4ZMVQP
Where did you buy this from ? I want one for my wrx but I can’t find anything other than AoonuAuto n I’m thinking they seem sketchy . They have nice stuff but I duno . With wiring and Led . If it’s not good stuff it could catch fire or something . Along with other concerns . Neway where from 🤔🙂
I just got mine from them. No problems at all. It's not going to catch fire lol if you think something this simple could catch fire then you definitely shouldn't be doing anything to your car
Julian Leone lol yeah I personally wasn’t thinking that I was talking to this dude he’s into cars a bit n he mentioned that n I was like what ? Jeez serious . This is my fist vehicle so that’s why I’m not sure and I’m not good with electrical . With my bike my buddy always helps me out . Yeah tho . When he said that made me wonder n from what I’ve seen so far with fb ads is that the are usually crap . Be way cheers n it looks awsm .
Does anyone know if i can wire it into the door welcome light? My footwell light will only turn on when i start the car due to aftermarket ambient light
Nope you can leave it on, if you are really concerned about shorting it out just turn off ambient lighting with the button above the rear view mirror by the sunroof switch.
I bought this I'm going to make it simple took me 5 min install buy a usb 10 ft from Amazon no splice really 5ft but I go ten to connect other things nice product get alot of compliment
The sill lights will illuminate when the doors are opened and goes off when the doors are closed that’s why it’s best to connect them to your interior/ footwell lights
Hi Tecky, any gauge will work just don't go above 24 gauge. You can try to find 18 gauge, that may be more common. The smaller the wire the easier it is for you to run and hide in the trim. Hopefully that helped.
Thank you for a brilliant tutorial very well explained and the step by step guide makes it easy for people to get a better idea of what’s involved
This looks like a lot of extra work
Were can I orden this parte for my BMW X5 year 2018 let me know please thanks
Pay an installer
Does it have a mode where its just on or off imstead of the sequence?
still waiting for this answer lol
@@mrandressss ya... me too😂😂😂
AND a link where we can purchase from! l
Great Video, but how did you know which wires to cut/connect to on the foot-well connector wires?
Great video. How do you wire the rear?
Thanks, so detailed. I just skipped to the trim removal parts n where u got power from.👍🏻
Glad it helped you out!
Where can I buy the wired sill ' only finding the wireless. Thanks!
This is so cool but to me makes more sense having one for every door. How can you actually make the wireing for the back ones?
the video is perfect you detail everything very well, I want to know where I can buy it and if it can be installed in a 2018 bmw m3
we sell on eBay. please search " autopan eBay " " gddworldwide eBay " in Google. Or search " autopan Sill Plate " in eBay. You could find it.
Great video man , where can I buy these? can you please share the link? Thanks
Great video tutorial!👌🏻Thank you. Looks great!
Any idea where or how can I buy this? A link or something? Thanks in advance. Cheers!
You are genuine man👍👍
Where do you buy them?
Nice... What's the link to those sill plate? all I see is those aftermarket custom plates!
Where can we get these??? You never tell us where we can get them, love them and your video.
why did u cut the wire when u can use quick splices for like 5 bucks
Why don't you put wire through the holes in the sill?, can it not be pushed through?
Why didn’t you use suitcase connectors instead of cutting the wires???
I think you did a great job! My only concern being a tech for 20 years is where the wire goes under the door seal I would be worried over time it would rub through and short out do you think if you took a cut off wheel and made a small relief cut so it had a pocket for it to sit in? I'm not trying to be rude by any means. Again great job
Or just use heat shrink around it
I've had wires bent over sharp angles in my 78 Torana and they are stiffly bent but still have no wear on them at all
Do you have a web link to where you can buy them from
Did you ever find out how to do rears?
Do you have a link for those plates?
I would have soldered the wires. I have also had good service just back-probing the wires into the connector. I did that when I added extra LED lighting to the trunk.
Where did you get those bro I want them
Thanks great video but watching you struggle with those gloves was a little hard to watch LOL but very helpful and it looks great.
Bill Winters excatly ahhhh I hate gloves
Did they burn out due to water damage
What are these rims called? They seem to be not so common for some reason.
Great work bro, wish they all were like this
Hello, where did you buy it?
Great video, thx.
I am trying to buy one, but one site says it works with 5 V. If I connect it to the courtesy light, it will be 12 V. I’m confused…
Where did you get yours..??
The moving sequence is so "kits"....there are way to disable?
the extension cable DIDN’T reach? we shouldn’t have to splice any wiring (you’re awesome man, solid video!), I’ll pass.
Not sure how I’d order for a 2-door M4 (2015), sure looks like more than 3 min installation
Awesome work bro!
Can they be on without blinking or any light movement at all?
This was the perfect install until I saw this bs. They grab a cool thing and ruin it.
My 540 came with illuminated ones from the factory. You can’t see the cable on a factory fit so perhaps you could run it some other way.
My factory ones are ‘on or off’ and don’t do the sequential display like yours. They are also a different graphic. Nice touch to the car all the same 👍
What’s the link for these?
Is this only for driver side
Great video! Thanks. I just ordered them for my A6 C7 BiT. I will def not use gloves though😬
Great,thankyou, I knew it was straightforward.
Bonjour quel est le lien pour acheter ce seuil de porte merci
Where did u get these
great video! how do we do the passenger side though? where do you connect those wires to ?
Exactly the same as the drivers side!
@@WeekndGarage thanks for the response! so basically, there's a cable point at the passenger side yea? i'll check it out! :) thanks for the video btw!
@@mrdude4433 No worries, if your vehicle is equipped with footwell lighting, wiring will be identical on both sides. Good luck!
Looks like the type i fitted to my Z4. Only problem the cable entry to the unit wasn't sealed. Water got in, it shorted and the wires caught fire.
Nice, where did you get them
Patience of a saint i mean me btw 😂
Great vid mate keep it up
Got some rechargeable ones to skip wiring, but barely last 5 days before recharging again
Is there a way to make them stay on without the light show? And where did you purchase these? Thank you, very informative install video
I wanna know that too
Great video. I think I would use wire taps instead of cutting the wires personally. So I've seen people install these, and almost bought them about 100 times. But I was curious how easily they get scratched up. You've had yours about 7 months. Do the plates themselves still look half decent?
Looks quite good still, i can send you a pic of its current state if u DM me on IG : )
How do I use wire taps
@@OhioBallKnower learn to use ur hands buddy
@@wherie i figured it out 3 months ago buddy thanks bud
were did u buy them from
Omg 10 mins to open the package
Can you set them to be either on or off, none of that flashing showing off rubbish ..?
Where did you buy??
Does anyone know how to actually remove the stock sill without breaking it? Every video I have found, they lever it out and break a clip or the sill where it holds the clip in place. Mine rattles and I want to fix it properly.
Where can I purchase
Make me think why the new panel don't snap right back in. And that too gone was way over kill they never dry
But in this way it s always working or not? I don t want it working while I M driving
Is it possible that the light is in one Position from the Start?
Link to where you bought them ?
Juan NJennifer think they’re from aoonuauto
What about the passenger side and the rear
Maybe in the future :)
Great vid buddy.
Having fitted mine, I found that the lights flicker when the engine is on. I'm guessing you didn't have that problem?
They work fine when the engine is off
you have to connect unlights flicker and you will no longer have a problem, you can buy it on ebay
Where’s the link to this??
Can you get this for an M3
Love it. I want to do this to my BMW.
Link to buy?
Can you do this on pre lci e90?
Great detail. I installed bmw holo on the door. Set of 4 on Amazon. Easy mod but great bmw holo at night. Suggest you do video on that as I wish i would have done and uploaded on here.
Can y the linke in Amazon to me Sending
I have too Match searched but nothing finding
Here ya go. May need to check model to make sure it fits your car. I have an F10 and it looks great. Was hoping you are near area so you can assist me in doing that mod you did. Heres link: 4Pcs Car Door light Ghost Shadow Welcome Light Logo Projector Accessories Courtesy Step Lights For BMW X5 E70 E90 E60 E87 F20 E92 E91 E61 F11 F18 E63 E64 F12 E65 X1 X3 X6 GT 3 5 6 7 X GT Series www.amazon.com/dp/B082DBS5Y7/ref=cm_sw_r_cp_api_i_emqdFbD4ZMVQP
Where did you buy this from ? I want one for my wrx but I can’t find anything other than AoonuAuto n I’m thinking they seem sketchy . They have nice stuff but I duno . With wiring and Led . If it’s not good stuff it could catch fire or something . Along with other concerns . Neway where from 🤔🙂
I just got mine from them. No problems at all. It's not going to catch fire lol if you think something this simple could catch fire then you definitely shouldn't be doing anything to your car
Julian Leone lol yeah I personally wasn’t thinking that I was talking to this dude he’s into cars a bit n he mentioned that n I was like what ? Jeez serious . This is my fist vehicle so that’s why I’m not sure and I’m not good with electrical . With my bike my buddy always helps me out . Yeah tho . When he said that made me wonder n from what I’ve seen so far with fb ads is that the are usually crap . Be way cheers n it looks awsm .
Do you have a installation guide for innova 2019
Can this be done on a m3
Are these available on the f10 ?
hey man, can you do a video installing the LED BMW LOGO EMBLEM ON THE TRUNK AND BONNET ?
Possibly in the future :)
What if u got ruber in the way
where can I buy these for my f13?
AliExpress.
Good video pal! Nice that it covers everything. Cheers
Does anyone know if i can wire it into the door welcome light? My footwell light will only turn on when i start the car due to aftermarket ambient light
What about passenger side? :/
Do I have to turn off the power when doing this?
Nope you can leave it on, if you are really concerned about shorting it out just turn off ambient lighting with the button above the rear view mirror by the sunroof switch.
@@user-xi8zj5wc9y thx
Great vid buddy. Very clear. Thanks :)
I bought this I'm going to make it simple took me 5 min install buy a usb 10 ft from Amazon no splice really 5ft but I go ten to connect other things nice product get alot of compliment
Can you explain how? Maybe link to products you used?
@@AlwaysTheNose go onto the website itself they sell a usb one
@@professionalgrade5999 cant find it
@@AlwaysTheNose maybe they got rid of it
Fantastic video 🤘🏻💯
Mmm ok & how do they turn on?
The sill lights will illuminate when the doors are opened and goes off when the doors are closed that’s why it’s best to connect them to your interior/ footwell lights
Multumesc pentru video
Does anyone know if this includes some kind of control or app to control the lights? I'm looking to get the multi color ones.
hey no place has 22guage wire man what else could i use?
Hi Tecky, any gauge will work just don't go above 24 gauge. You can try to find 18 gauge, that may be more common. The smaller the wire the easier it is for you to run and hide in the trim. Hopefully that helped.
You obviously don’t own an M series. And no this won’t trick anyone when you stick it on your chevy Cobalt
@@BlockchainToTheFace you cant be saying that
@@BlockchainToTheFace I know you were joking, but thanks for the laugh 🤣🤣🤣
Does this work on 2012 bmw 335?
Yes, if its an F30 body style. Should be the same across all the new generation bmws doesnt matter which series.
Wat if your car didn’t have that dash lite?
Unfortunately my 2002 540i E39 does not have the footwell lights I have to tap into it somewhere else I guess
@@scotthelms7915 wat i did in my camry was run a small fuse block n wire my sil plates to it for power and then to the doors for a switch
Great vid - subscribed!
Solder and heat shrink when joining wires much more professional job and looks better than those things you used to join the wires !!!!
I like my cars to be epilepsy free from all the ambient lights and extra lights
Thanks bro.
aside from the tutorial, you sound like a really nice guy lol idk why it came to mind
Thanks!!
Who can you work with them gloves ..
ahhhhhh fiddly bits
are this constantly turned on? once i lock my car, does it turn off automatically?
Scooter Craze its wired to the footwell light, so its only on when u open the door :)
Glennyboy how do you know which wire is for the footwell light?
@@simsownage footlight works all the time you drive with ambient light
Like be still...
clear , amazing video but you don't need gloves that make you prisonner!
But why.
SIRI .....SORRY I DON'T UNDERSTAND...LOL
Thank for the video but I couldn’t wait until it’s over, why so boring???????????
You took over half an hour on a job that should have taken you 10 mins.smh 🤦♂️
Cause he is a ....
Wtf
切れ味悪すぎw
Oooo i want those on my f80