GE Microwave Disassembly - Microwave Repair Help
Вставка
- Опубліковано 24 гру 2024
- Repairing a GE microwave? This video demonstrates the proper and safe way to disassemble a microwave and how to access parts that may need to be tested and/or replaced.
Here is a list of the most common microwave problems:
Microwave doesn't heat
Microwave doesn’t work
Microwave light doesn’t work
Microwave runs for a few seconds and stops
Microwave turntable doesn't turn
Microwave buttons don't work
Microwave display not working
Microwave turns itself on
Microwave is sparking or arcing
Microwave door won't open
Click here to purchase replacement microwave parts:
www.repairclini...
Additional microwave repair, troubleshooting tips, help with finding your model number and part replacement videos can be found on our website:
www.repairclini...
Tools needed: screwdriver, flathead screwdriver, putty knife, insulated screwdriver
Model displayed: GE Microwave DVM7195DF1BB
Connect With Us!
plus.google.co...
/ repairclinic
/ repairclinic
/ repairclinic
Join our free VIP email list for discounts and money-saving tips: tinyurl.com/pnn...
Check out our blog: www.DIY.RepairC...
Don't forget to like and comment on this video, and subscribe to our channel!
Curious. Why don't you demonstrate the removal (and subsequent reassembly) of the door from the microwave. You demonstrate every other removal procedure but this very important one.
Thanks for the demo on how to do so many repairs w/o damaging, so simple when you know how to disassemble 😉👍
Thank you so much .. would you please add a video to replace the Microwave Door Frame WB55X10859 (Door E)
Is there a way to remove and replace the outer front plexiglass of the microwave door? My GE microwave, model JES2051SN3SS, has a cracked front outer clear plexiglass panel.
Replacing the handle: I have a GE microwave, model #JVM6175SK1SS. On the handle, the top connection to the door broke. I ordered the replacement handle. Following the instructions in this video I was able to remove the inner trim and get to the handle mounting screws; took the old handle off, no problem. However, when I tried to put the new handle on, It was next to impossible to tighten the two screws enough to pull the handle ends flush on the outer door. I was afraid I was going to mess up the phillip's heads on the screws by continued attempts to tighten. I took the new handle back off and tried to deeply tighten the screws with it unattached to the door, impossible. I ended up using 3 small washers on each screw to gain a snug/flush fit. And yes, the (pricey) replacement handle was a genuine GE part.
GeneL56 z
Your video showed everything except how to remove/replace the door. I have a GE SpaceSaver over range micro. Any suggestions?
Did you ever find out how? I was cleaning my oven and stood up hitting my head hard on the microwave door while it was open and I’m pretty sure I just broke the hinge.
With everybody (almost) having a phone camera, I suggest taking a photo of all wires - or assemblies - before disconnecting
This way you'll have reference to how IT SHOULD BE RE-ASSEMBLED !
BEST
Thanks for the tip about sliding the top fascia to the left to release it, that was giving me fits. It allowed me to change the interior light which is the same G8 40W bulb as the underneath. Speaking of which it would have been nice to show that around the spot where you replaced the filter being that it is right underneath it. The bulb itself is readily available at Lowe's or Home Depot, but my appliance retailer wanted $18 for it.
ImAPCTech n6yy
hi, I have GE microwave, I replace all switch, but the fuse still blows when open the door! do you have any idea? thank you
Hi repair clinic what what is the model number of the microwave in this video? Thx!!!
Was able to replace my GE profile microwave door thanks to this video!
Thank you! Whole my husband was at the pool...I fixed the microwave..so far so good! Saved me money and listening to him complain!😊😊
You're welcome!
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
Hi, I have a countertop model. It is not screwed into a cabinet. I removed all the obvious screws and yet something is still holding on to the cover. All (as in *every last one*) shows built-in installations and how to unmount the microwave. I just want to take the darn cover off. Do I push harder or is there something I still have to undo?
Very helpful video for cleaning the oil stuck on top.
I got GE profile over the range microwave, I want to replace the bulbs that are at the bottom and provide lighting on the stovetop. It says 120v 40w for incandescent or 120v 20w for halogen. Is there a bulb number or model or those info are good enough? (looking for 5000k bulbs as I like those white lights)
great vid on disassembly
thanks for taking the time in putting this vid together
The Painters accidentally pulled too hard on my GE Mongram Microwave Control panel and the whole thing pulled off! It looks like it's held on by double faced tape. My concern is the big square button... Will that fly apart if I remove the control panel from the front? It looks like it's held on by a couple of tabs at the bottom plus the tape and would lift up and off but I'm concerned if I remove it, I wont be able to get it back on without taking the whole thing apart. Can you tell me if the Control panels with the built in big square buttons can be removed and replaced from the front of the unit?
Hi. Do you have a video replacing the glass?
chances are unless you found an identical dead donor MW to swap doors on? Totally not worth it
The video was very helpful! Of course, I need more experience on the use of the Ohm Meters.
Is there a video on how to replace the door? Thanks for your help in advance.
hey eric by any chance you find a video on how to remove the door?
I have not
Have you?
+Eric Schmidt no I haven't but I had to take off the inner plastic panel then the outer panel with the handle!there's the middle shell that holds the 2 panels together that's when u can take it off the hinge be careful with the new door I broke the old one easy!o yea u have to open the door all the way open to clear the notch that locks the door into the hinge!practice with the damaged door.I used a small flat head screw driver
did you ever figure out how to put the door back on?
BWAHAHA! I FINALLY took out one of the leads on the cursed beeper/speaker! NO MORE BEEPING! Especially every minute after it finishes warming my food! Oh man, I suffered for years, and it only took 20 minutes, including looking at videos on UA-cam. THANK YOU! (I just needed this video to see how to get to the control panel).
I wish the touch panel would light up once if tapped for night operating and not having to turn on the room light to see the panel.
I need to clean compartment below the turn table. It has holes and through the years all kinds of stuff got trapped inside. How can I clean this part? Thank you
The speaker that beeps in a GE microwave (much like the one you used to demonstrate repairs in this video) has stopped working. My microwave works perfectly but does so silently. Where is this beeper located? Can it be replaced easily. Thanks.
NO! Don't fix that damn beeper! Learn to enjoy the silence! Hehehe
If I was soooo lucky!!
I have this microwave with a 3 piece handle and i cannot see the screws without taking off the glass...or so it seems...any suggestions?
One of the most common problems is the internal light bulb burning out. Did I miss how to replace it?
Looking for video to replace the door for a jvm1490 model. Thank you.
Hi there. My ge microwave stop working luke 2 months ago. When its on makes a beeping noise consistently and i have to turn it off. When we like to use it we connect the power cord back on but sometimes it doesnt let me use the control panels,it reads DEFROST ON/OFF, SET TIMER , ENTER LBS. but i disconnect , connect back and press like #2 and gives me 2 minutes to heat but if left on it beeps again and again. And ideas of what can be wrong /fix
THANK YOU! AWSOME STUFF
You're welcome!
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
is the fuse replacement instructions on here?
No
Simply unplug unit gently pry out fuse and replace with same rating...mine was 20amp which is the same as the circuit breaker btw ...just blows faster than breaker would open I guess ...but WHAT caused it to blow? See unless you can explain that? Something is still wrong ..I suppose there is an outside possibility it had a junk fuse but otherwise something is probably about to fail...like magnetron tube etc ...is a microwave even worth repairing? Typically not so much ....GE apparently has a really bad reputation...at one repair parts site a gentleman said NEVER replace with a GE ....do your due diligence and find a great reliable brand. At our last house we had a Sharp Carousel that we just abused and used every day for like 20 years ...our kids live in that house and it is still works like new ....this GE? 2 years old ...pathetic
I have a Ge over the oven microwave and it will not turn on. I had replaced the door switches and the 20 amp fuse. Any added ideas?
Does know how to remove the metal frame inside the lining of the door? The metal frame of the my microwave is in the way of the handle screws, so it looks like I have to disassemble the entire door to get at those screws. Unlike in the video. Any help appreciated, thanks. My microwave is JVM3160DF3BB, Serial HG221413A.
My GE microwave didn't come with a plastic linner on the inside of the door. Ths causes splatter to get through the metal screen on the inside and onto the glass. There is no way to get in there and clean that so it always looks dirty. Returning it isn't an option. What do you think I should do? I was thinking of replacing the door.
RizzoSol Yes, your best solution would be to replace the door.
+BorrisDaBlade25 Cover things !!!
How to install model jvm1540dp1ww microwave
I have arcing on the inside at the right aft rack holder. It is actually burning the plastic holder. what could be the problem.
Thanks!
Control board is dead how can I replace or repair?
Anybody kno how to fix a low suction problem on the bottom of MV? I pulled the MV down and the fan moves tremendous air, but it's not sucking air from on top of stove.
my GE microwave (JVM3670) cooks normally but when I get through and close the door the fan automatically comes on and stays on until I open the door and leave it open. Any ideas?
Usually an indication of a door switch issue.
Something is rattling inside the door. I used a putty knife to remove that surrounding plastic but it's rattling inside the door still.
All I'm trying to find is the steam sensor. No mention of it in this video.
My Kenmore Microwave stopped working I order a fuse to replace it but the microwave have a specific type of screws that doesn't fit a Phillip or a flat. I contacted The seller but in order to fix my microwave I have to have it repaired by a repair services just to take off the panels a $75 fees. I tried to order the specific screw driver but it not sold in store. I'm sure I can purchased another microwave less than $75
You can buy those driver bits at any hardware store ...take a good picture of the head and go get what you need ...better and/or paint screw head with sharpie and immediately press paper on head with finger for impression and size of screw socket ...UNPLUG MW before opening panels! BTW the internal star point screws there are several sizes ...good to just by the whole set ...amazing how many things have those! TORX head screws is their offical name
All of that, but they don't talk about how to remove and replace the door panel..?!?
my microwave did work perfectly my nice pressed all the buttons and now it says reset and f4 what dose that mean ? and it makes 4 long beeps. it looks like it works but I think maybe it block or something:/
unplug wait 1 minute and plug back in ...lots of things CAN reset this way ...has happened on ours
Mines turned off by itself and nothing seems to be wrong with it?
Don't know what the sturablade does?
What does F3 code means
Click here for Fault Code Information: www.repairclinic.com/RepairHelp/FaultCodeLinks?TLSID=1943
Need video on how to replace microwave door
You can tell this dude repairs appliances because of his cut up arms. They never debur the sheet metal.
i want to clean my glass on my oven are a new door i have a spacesavor
How to repair microwave dash boards
My microwave runs when i open the door, anyone know what to do?
Mine was doing that for about a month then it died. I currently trying to repair it
Your door switch is stuck, replace it.
mine is stuck in spanish. help.
take a night course in hispanic
light switch doesn't work
AT REPAIR CLINICK WE MACKE FIXING THINGS EASEY.
DANGER HIGH VOLTAGE ELECKTRICITEY. KEEP OUWT.
unplug first at least ....never plug in with internal parts if you disassemble ...you could be frying yourself with microwaves and not even know it! Metal parts shield users
not even a GE , nothin like it even
I have a GE model PEB7226EH1ES and need to replace the tray motor. How do I drop the bottom panel to access the motor? This obviously involves more than just removing a few screws like in the video. Help!