T-Cut Rapid Scratch Remover

Поділитися
Вставка
  • Опубліковано 29 сер 2024
  • #productreviews #scratchremover #honestreviews
    SCRATCH REMOVAL MEGATEST
    Welcome to the Detailing and the Beast Scratch Remover Megatest!
    In this video, I review the fourth product in our MEGATEST - T-Cut Scratch Remover.
    Over the next ten days there will be 8 individual reviews, and a final Megatest video at the end scoring all the products and crowning the winner! 👑
    There is a playlist available with all 10 videos in this series here: • What is the BEST Car S...
    All products tested have been purchased by myself, none have been gifted, and none of the companies of products featured have had input into this test.
    All products featured are available to buy here:
    Autoglym: amzn.to/3pEyZU4
    Autobrite: amzn.to/355UMe8
    CarPride: amzn.to/352wT71
    G3: amzn.to/3cxZ2Y2
    Mantis: amzn.to/3vbcfwh
    Meguiar's: amzn.to/3w91FqN
    T-Cut: amzn.to/3w9SxCq
    Turtle Wax: amzn.to/3ze4Wak
    For all other Detailing products, from loads of brands, check out here: bit.ly/39hjSd9 and use code DaveCHCI for a 10% discount site-wide!

КОМЕНТАРІ • 26

  • @crazycressy7986
    @crazycressy7986 3 роки тому +1

    I love Tcut used it for 30 years

  • @SparkleanAutos
    @SparkleanAutos 3 роки тому +1

    Better than the last two but in my opinion, although you'll have a much better view than me (!), the G3 is still leagues ahead... It looks like a machine application compared to some of these!
    T-cut is underrated by a lot of modern (dare I say younger) enthusiasts but it still has its place - This very product helped me out of a tight spot with a hire-car in Spain a few years ago after a battle with a loose branch!
    Loving this so far Dave 👍🏼 excited about the 'pen' 😬😬

    • @DetailingandtheBeast
      @DetailingandtheBeast  3 роки тому +2

      You have it spot on up to now. G3 is way better.
      Pen is coming tonight at 6pm! 😊🤣

    • @SparkleanAutos
      @SparkleanAutos 3 роки тому

      @@DetailingandtheBeast looking forward to it 😊👍🏼

  • @steverabbits
    @steverabbits 3 роки тому +1

    New to your channel (thanks to Martin at OCD) I have never managed to get T-Cut to work very well for me, watching this I'm thinking maybe I didn't work it long enough.

    • @DetailingandtheBeast
      @DetailingandtheBeast  3 роки тому

      That may be the case. But give it until Sunday this week and I'm doing the megatest so you can compare all 8 and choose one that you like! 😊
      Welcome by the way!

  • @eamonkelly2792
    @eamonkelly2792 3 роки тому

    T cut didn't do a bad job, from the info on the tube I thought it would be full of fillers, 👍👍👍

  • @MJMDetailingDiaries
    @MJMDetailingDiaries 3 роки тому +3

    I love that the old school belter seems to be the best so far
    ...... especially for the £s.
    Keep going flinty, can't wait for the final day. 👊

    • @DetailingandtheBeast
      @DetailingandtheBeast  3 роки тому

      Today's will be a good un! 🤣
      I've still got G3 "up" at this point by quite a way. It did a much better job at swirls and the scratch. The T Cut wasnt actually that good. Itll show better when we compare them in the scoring bit on Sunday.

  • @tmphotography8443
    @tmphotography8443 3 роки тому +1

    Proper old school , almost as old as youtuber OCD Martin this stuff .

  • @HypnotizinDetailz
    @HypnotizinDetailz 3 роки тому

    This was the best so far I think 😊

    • @DetailingandtheBeast
      @DetailingandtheBeast  3 роки тому +2

      I've still got G3 up at this point. 👌

    • @DetailingandtheBeast
      @DetailingandtheBeast  3 роки тому +1

      But better than everything else so far.

    • @HypnotizinDetailz
      @HypnotizinDetailz 3 роки тому +1

      @@DetailingandtheBeast - Ohhh, really, that was looking a bit better... Just watched that video again and that one was looking a bit better (the light wasn’t that direct like in this case though), but I believe it to you Dave, as you have seen them in reality - and that’s what really matters, camera never gives the reality back. 😊

    • @DetailingandtheBeast
      @DetailingandtheBeast  3 роки тому +1

      I only scored them against each other at the very end when all were done. Switched off the lights and used the pen to determine worst to best in both swirl removal amd separately scratch removal. Was quite clear actually when done that way. TCut didnt seem amazing when I did that.

    • @HypnotizinDetailz
      @HypnotizinDetailz 3 роки тому

      @@DetailingandtheBeast - Looking forward to it! 👌🏻🤩👍🏻

  • @flesz_
    @flesz_ Рік тому

    Hm do not use on plastic bumpers?
    I thought that's what it's for

    • @DetailingandtheBeast
      @DetailingandtheBeast  Рік тому

      Plastic, as in unpainted. Any type of painted surface is fine, but the compound in this will stain unpainted or textured plastics.

  • @LeftyandFriends
    @LeftyandFriends Рік тому +1

    Can I tcut windscreen scratches?

  • @mahammad
    @mahammad 2 роки тому

    Does this eat into the clear coat? If so, should I spray on clear lacquer from Halfords?

    • @DetailingandtheBeast
      @DetailingandtheBeast  2 роки тому +1

      The answer is yes, but from your question I have to say "not as you think". It is an abrasive so diminishes clearcoat, bit you would have to do some serious arm time to take off that mich that you need lacquer. Also do not just spray clear lacquer onto any paintwork. It won't bond, and it won't just blend in. You will bebleft with a right mess that will cost a lot to rectify.

  • @foolsgold39
    @foolsgold39 3 роки тому +1

    You will have a sore buffing finger at the end of this megatest 😆

    • @DetailingandtheBeast
      @DetailingandtheBeast  3 роки тому +1

      It's got no skin 🤣
      Literally hours of this in the day this was all done.