Arduplane Autoland basics (how to use DO_LAND_START)
Вставка
- Опубліковано 23 тра 2024
- Huge thanks to Ben for helping with these videos! You can visit 3DXR here: www.3dxr.co.uk/
This is one of three videos on this topic:
LIDAR setup: • Arduplane Autolanding ...
Basic Autoland setup: • Arduplane Autoland bas... (this video)
Autoland with LIDAR: • Arduplane Autolanding ...
Thank you for taking the time to watch the video. You can find me on social media at
• / painless360
• / painless360
• www.thingiverse.com/painless360
You can help support the channel by simply liking the video and subscribing to the channel. It helps a lot! In addition you can use these links to support the time I spend helping others:
• / painless360
• paypal.me/painless360.
Remember that reviews are subjective. Don't rely on one person’s opinion - watch multiple 'reviews' and make your own mind up. Unlike some, I don't do this to replace a day job as that makes the creative decisions all about 'getting paid'. I am free to be completely honest and clear in the videos I make. I’m not asking vendors to pay for these videos, so opinions are mine alone.
Please also keep in mind that the comment section is not a forum: any comments that are rude, disrespectful or use bullying or threatening language will be deleted. Pedantry isn't encouraged either. This channel is all about helping others and passing on advice and ideas, so please comment in that spirit. Comments that don't adhere to these simple rules will be deleted.
Thanks again for watching! Remember to use the playlists as I collect videos into subjects to help you learn about a topic and find related information.
Please LIKE and SUBSCRIBE and above all - Happy Flying!
#drone #painless360 #review
Ardupilot has excellent documentation. But Ben adds all the little bits. Very helpful
A nice Arduplane series. Thank you Ben and Lee for sharing these insights. ♥👍👍
Thanks for all the info, Lee and Ben! 😊
Stay safe there with your family! 🖖😊
Thank you! Very useful Infomation
I've probably done over a 1000 manual landings ( not including crashes) and I'm very proud of the effort and patience required to become proficient at landing manually. ardupilot (with a pitot and lidar) makes my landings look like terrible, like I have done no practice whatsoever. The only type of landing that I can perform "better" than ardupilot is a very short landing area and stall the plane about 2 foot of the ground after bleeding enough speed during approach. if i did more research into the settings ardupilot could probably do STOL better than me. brilliant video as always
Ardupilot automated landing, when setup correctly, is a thing of beauty. But, it takes a lot of tweaking to get it to the level of an experienced pilot. You'll see some of the 'fun' in the final video in the mini-series.. Stay tuned!
@@Painless360 I had quite a few bum twitchy moments in getting set up properly but it was well worth the effort. The best reaction I got I was flying at a local event (community event not a rc club event) and with a home made foam biplane and the landing was uphill with a cross wind and ardupilot brought in down flawlessly. The president of the local rc club commented saying it was a very good landing considering conditions and was shocked and amazed when I told him it was an auto landing. I put the plane back in the air and started the landing sequence and put the trans down on the table within reach in case of a problem and it landed perfectly. only positive interaction i've had with a local rc club regarding flight controllers etc.
Thanks! Perfect timing, as I am getting closer to finishing my first arduplane (w/ LIDAR).
Very good attempt. Pls keep releasing new episodes
Nice, I press RTL and I go for a smoke with ardupilot.
Thanks for the info
Very impressive.
Nice!
Nice
😮
What's with the shake launch hmmm? 😀
Check out my video on it... Happy flying