2022 First Race Day! Audi + Hoosiers
Вставка
- Опубліковано 7 вер 2024
- Hey everyone!
We're back racing this year and had a great time out at Rad Torque Raceway!
I removed my interior and installed a Kirkey part no. 55170 race seat.
Rear section of my exhaust is removed with turndowns.
Antigravity battery AG-H6-60-RS.
Konig Hypergram 18x8.5 et 43 with 10mm spacers
Hoosier DR2 245/40/18
Half tank of E50/94
Over the winter I had all of the 034 Motorsport Billet Drivetrain Mounts, JXB C7 Driveshaft Center Support Bearing Carrier Upgrade (street) and the 034 Motorsport Engine Mounts (Street) installed.
Also updated to the Ver2.0 TB upgrade and Carbon Fiber Intake and the 034 Motorsport ZF8 TCU.
Kept the rest the same from the previous season.
034 Motorsport Stage 2+ ECU
57.75mm SC pulley
194mm Crank pulley
PerformanceBuilds Ported SC
Autotech HPFP
PerformanceBuilds Ethanol Content Analyzer
Gutted Cats with custom exhaust
MercRacing HX
CWA100-3
Weight Specifics:
Started at 4300lbs with me in car
Spare tire -38lbs
Driver side rear upper -17.8lbs
Bench -15.6lbs
Pass side upper -49.2
Jack -4lbs
Trunk floor -6.8lbs
Floor mats -9lbs
A6 front seats each weigh -66.6lbs
-273.6 with both seats out
Kirkey weighs 19lbs
-254.6lbs with Kirkey in
E50 mix @1/2 tank
-62.5lbs
-317lbs total removed
OEM 20" Wheel with 255/35/20 Continental DWS06 (54lbs)
Konig+Hoosier: 41.8lbs
-48.8lbs
Stock battery 65lbs
Antigravity battery (-50lbs)
Removing rear muffler section (-54lbs)
Total 469.8lbs removed
_______________________________________________________________________________________
Music Credits// Epidemic Sound
Intro Song sampled from:
Artist: Dusty Decks
Song: Jazz Bars
Album: HYPELINE!
Artist: spring gang
Song: Mister Magical
Release Date: November 19, 2021
Well done dude!
Thank you very much Cory!! Thank you for grabbing those wheels for me 👊👊😃
Nice runs!
Thank you Thomas!
Congratulations on the 10 sec pass ! Killer 60ft too.
Thank you Fred! Pretty pumped about that 60' myself!
@@SuitedUp2The9s were all these runs on the 034 Tcu tune? just raised the launch rpm?
@@rafaelbatu7525 yes all on the 034 TCU. I raised the stall up and did one launch with it settling on the stall and the other 2 were using the upswing method I describe in my how to launch the ZF8 video👍😃
@@SuitedUp2The9s awesome! Thank you! I just was asking because you got no wheel spin and I tend to get wheelspin on the 034 tune if I raise the stall rpms but im on street tires.
From logging it looks like the 034 tcu tune launches with bypass fully closed so full boost at stall where if I run the Berk Tcu tune with same 034 Ecu tune it will open bypass slightly and launch with about 10psi less boost but it eliminates my wheel spin even at 3k rpm with that slight difference. Just something I noticed and passing along if you didnt look at logs side by side.
@@rafaelbatu7525 yeah I definitely have looked at it side by side and compared 60ft launches of mine on how effective I can upswing. So that my bypass stays closed and never opens until I lift at the end of the 1/4. I don't even bother trying for good 60' on street tires for that reason, there's so much tq there I pretty much keep it to the drag strip now with the hoosiers.
I haven't logged my hp tuners tcu against 034s to see that. I really only stall launch it if I forget to raise the stall up before I launch. I've found I can get much better 60' by upswinging. Good info about that the side to side logs 👍 that 10lbs less is a big difference in hp/tq so it definitely explains why you don't spin then.
01:40 need to improve that reaction time. Excellent run and time though!
Yeah I am usually racing my PB times, less so the other driver. R/T I am going to work on later 👍😃 thank you man! It was great conditions for being up at elevation.
Flying out of the hole
No drama just hookin and bookin. Clean pass going A to B haha
Goals! Why didn't you use 17" wheels?
17s didn't fit my brakes, particularly my calipers. Not without 20mm spacers anyways.
@@SuitedUp2The9s 17s fit under my A7 with the 356 mm rotor, assuming the a6 brakes are the same. Did a test fit today of random 17s I had in the garage. The only thing stopping it from working was the front wheel weight near the face but nothing a 5 mm spacer couldn't fix. The caliper has a cutout in it to help with the clearance needed for the wheel weight.
@@andyrizzle7637 I tried my friends Konig Hypergram 17" and I needed a 20mm spacer to get it to clear. I'm sure it would clear other 17" like you said. I also am being picky on which 17" wheels, looking for as light as reasonably possible.
@@SuitedUp2The9s My friend has a pair of rpf1's (17x9 +22 and 17x10 +18) he is letting me try on. Would you recommend a forum I can post my findings?
@@andyrizzle7637 on Audizine or C7 Owners group on FB would both be good places. What do those weigh?