BMW RANDOMLY STALLING? FIX IT NOW P0340 P0344 Intake and Exhaust Cam Sensor DIY
Вставка
- Опубліковано 6 гру 2020
- This DIY shows you how to replace both the intake and exhaust camshaft sensors on the m54 engine. This video applies to many models with the m54 and m52 engines (e53, e39, e46, e83, e60, and more!). A bad cam sensor can cause random stalling, check engine lights, misfires, hard starts, and more. Make sure you replace the sensor and the o-ring when doing this repair. #bmwrepair #bmw #mechanic
Support my channel by becoming a member using this link: / @shoplifetv
My Amazon Store: www.amazon.com/shop/shoplifetv
Buy My Merchandise: www.shoplifetv.com
Ask me a question: www.shoplifetv.com
Request a Shop Appointment: www.shoplifetv.com
Instagram: @ShopLifeTV
/ shoplifetv
My vlog channel: / shoplifevlogs
UA-cam Business Inquires: Email me amotorwerks@gmail.com
Disclaimer: Some links will contain affiliate links. Due to factors beyond the control of ShopLifeTV, I cannot guarantee against improper use or unauthorized modifications of this information. ShopLifeTV assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ShopLifeTV recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ShopLifeTV, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ShopLifeTV. - Авто та транспорт
Just got an E46 and ur videos are like Ned’s Declassified School Survival Guide (e46 edition). Thank you 🙏🏽
Congrats on the new car! Thanks!
😂👍🏾
Before you "Fish the wire out" make sure you attach a lose wire to the connector with a duct tape and pull it out. That way you can re-attach the connector of the new sensor simply pull the other end of the lose wire to feed the new sensor connector with lead in the exact position of the old one. Work smart, not hard
Very good idea. Do u perhaps know the reason for this? I changed exhaust camshaft position sensor and the error codes never cleared.i have reset tool but the error reappears?
You sound like an electrician
@@anxiety3681 sr. Electronics engineer, but I still do a lot "hands on" at work and have fun with my car 😀
thank you good sir
Wow genius 👏🏿 😶
I just love the giggles when you start by saying, "you have to feel for the hole" Brilliant!!! I've always maintained the we'd make great gynaecologists, as much of our work is done by feel and mental imagery. I worked for a number of years in a Fiat dealership, the English translation,, from Italian, on every oil filter was: "lubricate ring and screw until tight" so many laughs were had. Never lose the schoolboy, or girl, sense of humour. I laughed out loud when you two got the giggles. Thank you for not editing it out 🙂
I'm so glad you're still making these videos!
This most definitely helped .. from removing all the parts to get to the sensor itself., to installing ... great video thanks 🤩 😁
Had this same issue. My e46 (M54) was shutting off on the highway and ended up being the crankshaft sensor
What up, J!? Been a minute since I popped in. Glad to see you are still at it. Hope the shop has been doing well and thanks again for all the vids!
Great video, will be replacing the cam and crank sensors on my E46 this week.
This guy deserve more likes and subcribers thank you for ur videos
Great video. Thanks for sharing!
Well explained, thank you !
GREAT VIDEO! YOU EXPLAIN THINGS VERY WELL. TWO THUMBS UP!
Thank You Scott!
Thank for the video… exactly what I needed!!! Subscribed!!!
Excellent video,thanks!
Another helpful video by ShopLifeTV
Great video. Thanks so much!
Excellent video! Thank you so much!
Just want I needed.Merry christmas from Orlando
You do fantastic work. ⭐️⭐️⭐️⭐️⭐️
Damn bro. Your videos are 👊💪🔥👏.
I got p0340 code and isn't the camshaft position sensor. No power lower speed, hard starting. Driving me crazy. Can't get to work 🤯
You should promote your merch with pictures included in the video, love the videos!
Excellent and work smart, bro
Thanks for video I'm having same problem with my e46 which also gave a code for cam position sensor
Thanks dude. I brought a 2000 323i sedan and loving it. Haven't had any issues stalling! Still getting the p0340 tho
I have the same thing but using another scanner read that the exhaust sensor is the problem not the intake cam sensor which I changed 3times oem.good luck
I have been having this exact issue with my E46 wagon for years can't wait to try this out over the holidays
Did it work mate? Mines been doing the same.
@@goldenthang what did you do?
@@xoxxxooxx sold it.
Top video as always👍👌
great job , wish you were here in Chicago to bring my 325 to your shop
I've had my 2001 BMW 325i for about 6 years, I'm not a mechanic but with your videos I've never had to hire one. Ive fixed everything from fan clutch, thermostat, electric fan, cooling system, all sensors and brakes. Thanks man. One question: Does the 2001 325i have the electric vacuum control valve that connects to the check valve? Can't get a positive answer from anyone. Thanks again.
01 325i is the best vehicle I've sat in..what a pleasure
Thank you
Today I worked on my m52 and replaced both inner heater hoses ,man that intake is a back killer to remove and put back. 😂 8:36 lmao those elbows are ashy
excellent, thx from EU
Great video! Any chance you could do a video on the S54 procedure? I understand its located behind the engine as opposed to the front.
Thanks for this video, I just used it to replace my intake camshaft sensor.
BTW as long as you are there, you may as well replace the intake VANOS solenoid as well. It's a wear item and it has to be removed anyway,
what are symptoms of vanos solenoid not working correctly?
It couldnt be better explanation on all your videos, well done
What diagnostic do you use for you bmw's ?
Thank you
You are the one that showed me to Unclip the Mass Air Flow Sensor, and this time you removed the hose clamp, the long way, poor boy must be stressed
Awesome video. If you are getting the code but almost never any noticeable symptoms. Can you get away with not replacing it?
8:56 ... LOL ... the frustration is real ... we've all been there
Always love your helpful great content. Thank you! I have had and I believe many people have a problem with mt S54 on my M3 stalling out often when I put the car into reverse as well once the car is hot and been running for a while the car just stalls out. Ive tried to figure this out as have many others. I can tell the change comes as soon as I put the car into reverse don't even have to use the clutch. The car starts stalling when i put it into reverse and it's idling. I had a BMW indie shop look at the car and try to figure out whats wrong. They checked the idle control valve but that wasn't the problem they did a software update and no good. My car is a swapped out 2002 330CI to a 2006 M3. Maybe that is part of the problem. As well when the car is hot and I push in the cltch and let the revs fall to idle it will just stall out even if the car is moving (Not in gear mind you). On and on it goes. LOL.
great video 👍i hope they are some news about the e30 coupe project
Thanks! We will have some upcoming videos on the e30!
Is there anyway to decipher between intake and exhaust side sensors throwing the code? Thanks again for the video!
O boy u know that frustration
Did both sensors on my 2004 Z4, M54 3.0 engine. Similar but different. The intake sensor was the easiest. The exhaust sensor was very difficult to get to, too cramped of an area. Once I got it out I struggled to get the bolt started in the new part, I decided to take the electric fan out. Should have done that to begin with, one plug, one screw and one expanding rivet and the fan comes out. Anyone doing the exhaust sensor on a Z4, save yourself some frustration and remove the fan first.
Just watched your P340 RnR, 02 325ci M54, great video and enjoyed the sexual references installing the exhaust sensor, good humor lol
THX BRO , the first one was intake or exhaust one?
Can you show and or demonstrate on the n62 4.8
Two years later, I still laugh at the "Feel for the hole" commentary.
I have a 2000 Z3 with a 2.8l. It's kicking my ass trying to figure out why it went from running perfect, to misfiring and running horrible and not even drive able. I changed and checked:
Both Vanos
Intake and exhaust cam sensors
New plugs
New coils
New MAF
DISA is fine, holds vacuum
Fuel pressure is rock solid, even when running like shit.
Smoke checked and NO vacuum leaks.
check this, i had a crank but hard start. Changed oil filter & regulator/engine temp sensor/crankshaft sensor/fuel pump respectively, doesnt fix my issue. Switched the camshaft sensors between the intake and exhause, turns out i have a bad intake camshaft sensor. So now the bad one is in the exhaust side and the car starts fine.
HI, I have the P0339 on my M54. Would you please give me some guidance on that? Thanks so much
Those 2 13mm bolts definitely need a thread sealant. BMW in Australia uses Loctite SI 5970.
$45 at BMW dealer only
Pls do a DIY on MAF troubleshooting - my car drives perfect with MAF disconnected. When i connect it wont even start eventhough i have replaced it with a tested and working OEM part (from a junk yard).
Question my 04 530i has these same symptoms once the engine is up to temp it will die randomly while parked at idle, or like you said at a red light. Could the sensor need to be replaced without throwing the code for it? Or would it be more of the vacuum side of the motor?
Can you do a video about P0220?
You are the best BMW channel. I have things i have fixed things on my 2001 325i & i can't get the lights on the dash. Could you please have help as i have seen many videos & its all shade tree mechanic bull shit. You will be helping many others as well young man.
Iight to go off.
hello my dear, so can you tell me if it’s very harmful to walk with 1 connecting rod i have an e46 328 i'm in love with it
Hi and thanks for the video. Would you please tell me if these sensors are also called Crankshaft pulse generator? That's on M54. Thanks
Hello I do have p0340 after head gasket job, I bought a brand new sensor, do you think o should retime the engine? The timing was perfect when I did it, with the 2 tools perfectly fitted, and also after turning one time the engine by hand
2000 328CI, 134k miles. I got a P0340 code after changing my pre-cam 02 sensors with new BOSCH sensors. I cleared the code and it didn't come back, but I've noticed the car in general can take a few cycles to start up, and the acceleration is not so great, especially when I floor it on the freeway. I feel like this car should be a lot zippier? Should I still replace 1 or both of the sensors? Thanks for the great videos!
Do you have a video for the camshaft on the V8 engine?
My 2000 328i manual does this, on a cold start it idles high but as it warms up it almost dies and sometimes stalls. I`'ve had it couple times stall when I down shift to a lower gear. Do you think this will resolve my issue.
Can you show me how to change the engine oil pan gasket BMW X5 2002 3.0i e53 m54
2000 323ci. Replaced inlet cps and exhaust cps and the crankshaft position sensor and still having the stalling issue.
hi do you have a high pressure pump for a bmw x5 2005 3.0i?
What would you do if you have all 4 sensors errors? I have a e65 2003 4.4lv8 with all four camshaft sensors reading high voltage?
What is the part number for the hex screw using on cam sensor
I’m getting no crank at trying to start up my 2001 330i changed vacuum lines, cracked air box and air intake boot would this help with any of my problems or the EML light
is the intake and exhaust cam position sensor the same part?
What size Allen wrench you use
Is the intake sensor and exhaust sensor made the same. Is both sensors identical?
Works on 90s, 2000s BMWs for over 5 years. Still uses sidecutters to get the intake airduckt clips out. xD
No offense, just reminds me of myself xD. Them darn clippullers cost almost 5 bucks, money better spent on gas. xD
Love your vids Keep it up.
any idea if this code comes in conjunction with a very complicated P16A7 code? got an M54 and it just stalls out. Cats are definitely clogged but also have a tiny cylinder head crack. Car stalls out randomly (SMG). however It doesn’t happen when the MAF is unplugged. Maf was replaced with an OE part about 2 years ago.
hey How much will this service run ?
More x5 stuff please!
Hay bro please help I have 750i my car gave me same issue so Do I need to replace all 4 or just the driver side 2 sensors
Very recently i cleaned the idler valve, and accidently unplugged the intake cam sensor, car stalled when idling and coughed and spluttered while in low range
I had a long crank- barely start condition. I've had intermittant CEL's for intake cam sensor, but no CEL this time. Could it still be the ICPS?
Where on the 2012 X5 V8 twin turbo motor those sensors be ?
What is it about the sensor that goes bad?
Hey, when i timing a vp44 on car i put with comparator 0.90 (thats write on pump)
Then block then i put engine in TDC. But when tighten the bolt on pump
the measure on the comparator moves.
and when I check again if the pump is in timing it is not correct.
What to do
Pleeeeeeeease help. Following the steps here, when I took out the exhaust side cps I managed to push the O ring into the engine. How big a deal is this? I was tired and not very careful at time.
I have a 2012 BMW X5 I just bring it from Dallas TX to North Dakota , on the Hwy everything was very good, but went the cold temperatures start going to cero by Fargo nd the car stars with issues, low engine oil, low coolant and losing power as well , so I stopped in a gas station and get oil and coolant I was 2 hours away from home, luckily I made it safe, next day my wife took it to the grocery store and the car stars showing a lot a codes like battery needs to be Replaced and 4x4 needs service and misfire codes and camshaft sensors too. I’m just replace the battery already but I’m very confused with this camshafts and crankshaft sensors, can you please provide a part number for each sensors I need for this vehicle 🙏
Would a(32mm) 3mm super thin wrench work? Or I need a thicker wrench?
i had bmw e90 320i N46 engine. Car cranks but not start . Scan and prompt camshaft sensor inlet. replaced the sensor but no start/ check signal voltage its 10V.may i know whats happen?Any advise?
Hi I've got a e90 330d with the m57 engine it starts fine but it cuts off while driving if I put my foot down or going uphill in park it will rev all the way but in gear it doesn't I've changed fuel filter glow plugs cleaned the egr aswell I've changed the ekp module also but problem is still there please help isn't showing the eml or any fault codes
Hi, E53 3.0i i change both camshaft sensors, but the issue with intake camshaft position its still there
sometimes the car is cranking 4-5 sec and save the error on intake cam sensor and the vanos is not working?
after restart and delete the erorrs everything is ok
what is the problem?
Can the e cam sensor oring fail and give a oil leak on to the bottom radiator hose closer to the top by thermostat
sometimes my car starts perfectly and other times it cranks and stalls or cranks only but if i give it gas it’ll start. no codes or lights. could it be cam sensor ?
Question, do u need to replace it with an original bmw part ..if not can u send me a link of ur choice to buy thks
Are meyle sensors ok to use I’ve just bought some they look identical to genuine bmw with the grey wiring and green seals they feel very good quality wise and will be replacing my cheap £15 Chinese set I got of eBay. Surprise the exhaust one has failed already after a month
Manual X5??? Yessssssss!!!
Is it possible to have a sensor problem but no error messages when scanning?
the e46 M52 has an additional vacuum line attached to the Fuel Pressure Regulator. Has any one done a catch can on an m52? If so, how did you tie in the Fuel Pressure Regulator vacuum line
I know on m54 you can cancel it out (or maybe reroute to top off gas thank, just an idea...), it’s only there if the pressure regulator fails and drips fuel.
My bmw 116 iwhile driving, the engine suddenly stops. the car has 282,000 km and I have never changed the 3 sensors. I believe they are to blame for this inconvenience. what do you think?
Can also be P0369
What happened to bmwselena
Hi
My E90 330i 2008 automatic,
After running 30 40 km ,when I slow it down for signal or humps it’s engine get turned off then if I restart it will restart and running smoothly
What is the reason?
My 32mm fan clutch wrench is RUINING the solenoid metal! It's chewing it up AND I have zero rotation of the solenoid!! Im stuck! Ive applied BP Blaster. No progress! Just metal shavings! Is there another screw or bolt holding it in??
You didnt put the same sensor (orginal part with orginal shape). Is this okay that i do the same?
Hey me bmw 530 is misfire 4 the code is p1349 I speed it up and it doesn't respond it turns off
Hey my guy appreciate the video but i need to ask a question i have a 2004 bmw x5 3.0 i have changed the cam sensor and im still getting cam code what else could be the problem other than timing
i have the samo problem, did you get it?
Bro did you find out what the problem?
Because I have the same issue 😢