I am having difficulty in setting up the ADS1015 ESP32 IO PIN config for volts watts gauge switch etc can you please confirm the pins used so I can setup Blynk please
Good day. Pave now I'm buying components. I already have almost everything, but what kind of mosfet 190n03 is this. I can't find anything after marking. Video time 2:47.
May I ask the Mosfet transistors you spec are 290N08 these are serious power 290Amp 80V can I use N channel type IRFP260 these are 50AMP 200V many thanks
Can u tell me.. At night.. When solar power is not available... The 90v to 12v buck converter is activated via 12v battery... Which is not enough to produce 12v at output.. Because this buck converter input is only 12v and as battery decreases.. the output voltage of this buck converter is further reduced.. At this time.. Ir2104 vcc pin is not getting 12v...its only 8v on vcc pin of 2104 ic... Can it causes mosfet switching problem or any other problems..?? Thank you...
Hello everyone. Just today I modified this mttp to 120 v. Successfully! Modification of the sleeper in the replacement of components. Mosfet Q3 and Q4 290N08 must be replaced with IRFP4668. Capacitor C3 470uF at 200V. Resitor R15 value increased to 200K. Arduino goes line inVoltageDivRatio = 40.2156, // Input voltage divider factor (200+5.1)/5.1. The voltage is must not increase because it is limited Buck Stabilizer 120V to 12v. That's enough for me. Enjoy it.
Greetings to you. I have already built it, but I have a problem with the thermal sensor. I used PT100. It shows strange values. What thermal sensor should I use?
Can I just kindly add you had a link on here now removed to purchase the ESP32 chip and I ordered it, it has arrived but it has no antenna plug to the rear and someone told me it does not come with any peripherals please can you advise
Sorry to ask a silly question but in your youtube video there are two main electrolytic capacitors one I can see a value of 1000uf 63 volts, however in your circuit board design they are both 470uf will this charge controller accept input of up to 120 volts @ 30 amps input and provide 12 volts 24 volts 36 volts 48 volts out and calculate best current out or how does this work.And will these capacitor values have to change depending what output or input required if that makes sense sorry for the long question.And thanks for this by the way
Nice Mppt. Nice board PCB too. You could have made for all THT components. It will make beginners to build quickly. Thanks for this project. Can one use it for input of say max 150v?
What size is the ferrite core please Dimensions and can you possibly confirm the size of your pcb for CNC (ACTUAL BOARD DIMENSIONS PLEASE) many many thank you.
Are you going to make this available for others to build, I have no electronics education, but I like soldering pcbs, and am in need of charge controllers, I have a 12v small system, for lights and backup inverter, and larger 24v system, with 1200w, and 2700 watt panel arrays, if I could get mppt control of charging by building it, that would be great, I have 8 strings, and basically each needs a controller, or I need a larger amperage output controller, a 120-150amp controller would be awesome, would it be possible to upgrade the output stage to buck, approx. 60v-80v to 24v- 30v with enough MOSFETs to pass 200-250 amps, at 70v Incase I want to move to 48v, (this is what I need to do, to get by with only 2-3 60a controllers) I have 2x 30a controllers and 2x 60a controllers,but need more to get all the panels wired up, I have LiFePo 12v battery, and 7s liion (nmc) for the large bank in excess of 1000ah at 25v, and going to add more, or save to go to lifepo4, you are a genius, I wish I had the encouragement, the opportunity, or even had a better school experience, I wish I learned more about this years ago!
Friend if i want to increase the PV voltage to 150v can i equally change R15 and if i want to increase Battery voltage to say 48v can i equally increase R17 and to what values of R15 and R17 should i use? Sorry for disturbing you.
Create the QR code for the Blynk app so that if the if the QR code is being scand one can have it in stalled in once phone like the one Techbuilder did.
Friend please could u provide QR link for the phone app in the code. Your code becoming more interesting to me more than the TechBuilder own, Keep it up.
Hello nice project.i wanna made your charger project but i can’t working with gerber files .can you share here .pcbdoc files you made with altiume here ?Tanx or send me link of pcb altiume file for me to download.tanx.
@@4EProjectsChannel hello and tnx for your perfect projects,here pcb companies don’t accept small gerber or pdf they only work with .pcbdoc in small boards and this is my problem to made only one of any projects for myself .but tanks lots of you,with good wishes
Thanks i have finally compiled the code now. Further more can you make the code two phase mppt 70A, input upto 300v output auto detect from 12v to 48v system. It will enhance ur followers and more subscribers to ur channel.
Hi, please reply our request. Please do complete sine wave inverter using this mcu which have menu buttons for parameter setting, LCD . 4 pwm hbridge sine wave inverter.
@@4EProjectsChannel anh có thể cho em hỏi làm thế nào để mình có thể ổn áp đầu ra khi điện áp đầu vào nó thay đổi vậy anh ? Giả sử khi mình có một tấm pin thì chỉ có Vmppt, nhưng khi mình mắc nối tiếp 2 tấm thì đầu vào là 2 Vmppt.
@@4EProjectsChannelEm có 1 tấm pin mặt trời có Vmppt là 40V đầu vào còn điện áp đầu ra là 12V. Nhưng khi mình mắc nối tiếp 2 tấm pin thì Vmppt lúc này là 80V nhưng phải đảm bảo đầu ra vẫn là 12v. Anh cho em hỏi làm thế nào để mình có thể ổn áp đầu ra vẫn là 12V khi đầu vào Vmppt nó thay đổi như trên. Với trường hợp mắc như vậy thì nó có ảnh hưởng tới thuật toán dò tìm công suất cực đại không anh ?
@@4EProjectsChannelreally? what is the another possible causes for the issue? What about the IR2104? The IR2104 in SD and IN measured pulsing 0.8v with multimeter. Is it genuine?
Hi @4E Projects Firstly, Kudos to you for implementing and developing solar charge controller of 30A with ESP32. When I compiled the Arduino project in my PC, I am facing the following error due to some functions written in LCD_Menu. The project is getting compiled if I disable the charging current part in LCD_Menu code. Have you ever faced this error....??? Kindly help. Early Response is appreciated. '''...8_LCD_Menu:377:1: error: insn does not satisfy its constraints: 377 | } | ^ (insn 11 2651 1185 127 (set (reg:SF 19 f0 [orig:127 _95 ] [127]) (mem/u/c:SF (symbol_ref/u:SI ("*.LC357") [flags 0x2]) [0 S4 A32])) "C:\Users\chara\Downloads\CODE_MPPT_ESP32_V1.2.1-20240819T055256Z-001\CODE_MPPT_ESP32_V1.2.1\8_LCD_Menu.ino":205:33 49 {movsf_internal} (expr_list:REG_EQUAL (const_double:SF 0.0 [0x0.0p+0]) (nil))) during RTL pass: postreload C:\Users\chara\Downloads\CODE_MPPT_ESP32_V1.2.1-20240819T055256Z-001\CODE_MPPT_ESP32_V1.2.1\8_LCD_Menu.ino:377:1: internal compiler error: in extract_constrain_insn, at recog.cc:2692 Please submit a full bug report, with preprocessed source (by using -freport-bug). See for instructions. exit status 1 insn does not satisfy its constraints: ...''' Thank You Charan Sai
![Lp. Сердце Вселенной #60 РОЖДЕНИЕ ЛОЛОЛОШКИ [Финал] • Майнкрафт](http://i.ytimg.com/vi/YoR0pAV9FVQ/mqdefault.jpg)
Thanks for watching 😉😉😉
Subscribe to my channel if you like❤
Give me reply if possible same In arduino nano v.3
Thank you very much for the project. is it possible to change ACS724 instead of ACS712 for drive 40 Amp.
I am having difficulty in setting up the ADS1015 ESP32 IO PIN config for volts watts gauge switch etc can you please confirm the pins used so I can setup Blynk please
@DIY Tech hey please help in geting our phone app setup too please create a scannable Qr code to add template for the app
Hello,
With Blynk 2.0, there is no QR code sharing function,
hi dear friend, what ferrite ring did you use, size or mark please tell me? Hello, from Kazakhstan)
Hello, I'm using a toroid with an outer diameter of approximately 30mm. I wound around 27 turns of 1.5mm wire. You can refer to my specifications.
That’s clean man ! Good work 👍🏻👍🏻👍🏻
thanks
Good job, but I think for 30 AMPS all day long this small cooler is not enough.
that's right, I will add on the next versions
Do you have the Blynk IOT code please for all the WIFI gauges to work on iphone many thanks
Hello,
The new version of Blynk can't share QR codes yet.
Bro you are great man
Thank you, brother.
@4EProjectsChannel bro i am from Pakistan i want to build own mppt i am working solar installation locally
Your country
Good day. Pave now I'm buying components. I already have almost everything, but what kind of mosfet 190n03 is this. I can't find anything after marking. Video time 2:47.
Ok, I will update
cho mình hỏi cuộn cảm 64uh này mua ở đâu thế ạ
shopee gõ: lõi cuộn cảm là có nha, mua loại màu đen, đường kính khoảng 20-35mm
May I ask the Mosfet transistors you spec are 290N08 these are serious power 290Amp 80V can I use N channel type IRFP260 these are 50AMP 200V many thanks
Hello,
You should use Mosfet with equivalent large capacity so that the circuit can be optimized
@@4EProjectsChannel ok thanks
Can u tell me.. At night.. When solar power is not available... The 90v to 12v buck converter is activated via 12v battery...
Which is not enough to produce 12v at output.. Because this buck converter input is only 12v and as battery decreases.. the output voltage of this buck converter is further reduced..
At this time.. Ir2104 vcc pin is not getting 12v...its only 8v on vcc pin of 2104 ic...
Can it causes mosfet switching problem or any other problems..??
Thank you...
Keep it up man!
thanks bro
Excellent work my friend, did you try it to make sure that there are no problems that could happen in the future
thanks you
does something need to be changed in the software? or written directly?
change in settings
Please can you share the machine link you use to print on the transparent sheet?
To create that transparent acrylic sheet, I use a CNC machine.
@@4EProjectsChannel which of the CNC ?
I personally custom-built the CNC machine.@@yuribiktop6595
@@4EProjectsChannel , oh nice one
Hello everyone. Just today I modified this mttp to 120 v. Successfully! Modification of the sleeper in the replacement of components. Mosfet Q3 and Q4 290N08 must be replaced with IRFP4668. Capacitor C3 470uF at 200V. Resitor R15 value increased to 200K. Arduino goes line inVoltageDivRatio = 40.2156, // Input voltage divider factor (200+5.1)/5.1. The voltage is must not increase because it is limited Buck Stabilizer 120V to 12v. That's enough for me. Enjoy it.
so great
excellent . I made the same using Arduino uno rev3 ,atmega328p controle solar charge mppt 12v 15 A with 95% efficiency.
Thank you! Cheers!
Please give me the file
@@madhusudanraut1738
ua-cam.com/users/shorts4skbGmwAx_Q?feature=share
Circuit
You have project file?
What is the value of the thermister and is it used as it is not on your list? thanks
hello sir what should i do about arduino code ? i need to only upload one code name CODE_MPPT_ESP32 ? and what library are you using ?
Hello, all documents including code, pcb,.... I have shared via the link below the video description. Please download it to use.
Greetings to you. I have already built it, but I have a problem with the thermal sensor. I used PT100. It shows strange values. What thermal sensor should I use?
Hi,
You need to replace PT100 with NTC10k . temperature sensor
Please which software did you use to design the pcb
I use Altium design
Ok But I uploaded the code but is not displaying on the screen
Nice one
I did not find si2306 do you know any equivalent mosfet ?
You can use AO3400 N mosfet
Can I just kindly add you had a link on here now removed to purchase the ESP32 chip and I ordered it, it has arrived but it has no antenna plug to the rear and someone told me it does not come with any peripherals please can you advise
you can use any ESP32 Module, that is 38 pins
Take an antenna from an old laptop and plug it in or solder it onto the circular pads
em làm đồ án thiết kế mạch sac mppt từ pin năng lượng mặt trời cho pin lithum sử dụng stm32. Em làm như này được k ạ
được nha. nhưng phải thiết kế và lập trình lại PCB và code
Nice job sir, please how can i get that app you are using for monitoring?
Hello, you need to download the Blynk app to remotely monitor various parameters.
Sorry to ask a silly question but in your youtube video there are two main electrolytic capacitors one I can see a value of 1000uf 63 volts, however in your circuit board design they are both 470uf will this charge controller accept input of up to 120 volts @ 30 amps input and provide 12 volts 24 volts 36 volts 48 volts out and calculate best current out or how does this work.And will these capacitor values have to change depending what output or input required if that makes sense sorry for the long question.And thanks for this by the way
Hello,
You should use the component parameters as in my design.
With this prototype, Vmax is only 60V DC, on future versions I will upgrade more
nice job,pls can this project be used without the app? mine is not compiling i mean the code
To disable the application, simply remove the line "Blynk.begin."
Hi sir what is inductor.. Kool mu??? Ferrite cor?? Plz ans
In the evening, wind about 30 turns of 1.4mm wire. Wind the coil with an outer core of about 30mm.
Hi. I have a problem. Why mosfet Q3 and Q4 mountains?
Hello,
I don't understand your comment
Nice job brother. Do you sell it? I want to buy
I would really like to sell it to you, but the issue lies with the shipping method.
@@4EProjectsChannel what’s your country? Maybe dhl or fedx we can use
hallo good work I have try to understand the module near the display connector the straight thing what is the name
otherwise keep up
hello,
That is LCD1602 + I2C
@@4EProjectsChannel thank for your response im grateful sir watching from(Nairobi ,KENYA)
Nice Mppt. Nice board PCB too. You could have made for all THT components. It will make beginners to build quickly. Thanks for this project. Can one use it for input of say max 150v?
Yes
That's max 80v, check the original project on techbuilder Channel 🙄
Hello. How solar plates are reqiured
You should use a solar panel with a voltage of 20-60V.
@@4EProjectsChannel can you tell me all modules names in this circuit use
@@4EProjectsChannel can you tell me module names of buck converters, LCD module????? All module names????
What values am to change if am using this Mppt for 12v to 48v battery system?
Capacitor parameters can be increased to 48v . system
What size is the ferrite core please Dimensions and can you possibly confirm the size of your pcb for CNC (ACTUAL BOARD DIMENSIONS PLEASE) many many thank you.
Ferrite core size : OD = 33.5mm , ID = 19.5mm , H = 11mm , you can also use the same size choke.
PCB size: 150x119 mm.
Are you going to make this available for others to build, I have no electronics education, but I like soldering pcbs, and am in need of charge controllers,
I have a 12v small system, for lights and backup inverter, and larger 24v system, with 1200w, and 2700 watt panel arrays, if I could get mppt control of charging by building it, that would be great, I have 8 strings, and basically each needs a controller, or I need a larger amperage output controller, a 120-150amp controller would be awesome, would it be possible to upgrade the output stage to buck, approx. 60v-80v to 24v- 30v with enough MOSFETs to pass 200-250 amps, at 70v Incase I want to move to 48v, (this is what I need to do, to get by with only 2-3 60a controllers) I have 2x 30a controllers and 2x 60a controllers,but need more to get all the panels wired up, I have LiFePo 12v battery, and 7s liion (nmc) for the large bank in excess of 1000ah at 25v, and going to add more, or save to go to lifepo4, you are a genius, I wish I had the encouragement, the opportunity, or even had a better school experience, I wish I learned more about this years ago!
Hello,
Your system is really good quality.
NICE 👍👍
the reference of the Q3 and Q4 mosfets?
290N08 MOSFET N-CH 290A 80V
i need help pls what do i do to use it without the app?
To disable the application, simply remove the line "Blynk.begin."
Friend if i want to increase the PV voltage to 150v can i equally change R15 and if i want to increase Battery voltage to say 48v can i equally increase R17 and to what values of R15 and R17 should i use? Sorry for disturbing you.
Hello,
You can use the voltage differential formula to calculate the voltage V out based on V in max,
V out is in the range of 0- max 5V DC
@@4EProjectsChannel Noted FOR example VR2 =(R2)Vs/R1+R2 I hope I am correct.
Works for 12v solar input?
requires input above 17V
Great
thanks bro
Can I use 30pin Esp32... Instead of 38pin Esp32...??
you can use ESP32 30Pin to replace
@@4EProjectsChannel Thanks..
Your location can you supply finished product ??
Có bán k a trai?
Good design... But why the efficiency is low... around 85%..??
What is the reason...??
Hello,
I think the problem comes from the inductor because it is not optimal
@@4EProjectsChannel I also think so..
Thank you
Nice video, thanks :)
Thanks bro
Can u use this mppt 545w 12v panel
At 12V and 20A, we have approximately 250W.
Its work with 24v batt?
Support for output from 9-30V
@@4EProjectsChannel Nice! i'll build it Thank you o much !
Dear bro, awesome work ❤️❤️❤️
Can you share blynk iot settings, thanks in advance.
you can see variable names V0, V1, V2,... in File Code. use it at Blynk IOT
Create the QR code for the Blynk app so that if the if the QR code is being scand one can have it in stalled in once phone like the one Techbuilder did.
@@4EProjectsChannel hey please help in geting our phone app setup too please create a scannable Qr code to add template for the app
@@ezeoluchukwu5104 Hello,
Currently on Blynk 2.0 version there is no QR code function.
Sorry for this
I did the assembly, but it shows the voltages incorrectly, and the charging does not start
Có nhận phay mạch ko a
Would have been nice to have audio describing what was going on. Nice video though.
thanks you
Hai sir I'm using your source code but I'm facing one error liquid crystal not such file directory... That error is indicating
what is that error?
Friend please could u provide QR link for the phone app in the code. Your code becoming more interesting to me more than the TechBuilder own, Keep it up.
Hello,
Currently on Blynk 2.0 version there is no QR code function.
Sorry for this
@@4EProjectsChannel You are great I know in the main time you will come up with more up to date on this project. thanks
thanks you
Bác thấy mạch này chạy ổn định không ạ?
Ổn định, dùng tản nhiệt to hơn với quấn lại cuộn cảm thì ok
Hi can you make the one that we be able to input the WiFi name and password through the LCD menu by using the button
Okay,
I will develop more in the next version
@@4EProjectsChannel ok I will be waiting
Please some credits and linkage in the description are needed to Techbuilder original mppt project, without that this could not exist
Tuyệt vời
thanks
Hello nice project.i wanna made your charger project but i can’t working with gerber files .can you share here .pcbdoc files you made with altiume here ?Tanx or send me link of pcb altiume file for me to download.tanx.
I have shared the .PDF file and also the Gerber file
@@4EProjectsChannel hello and tnx for your perfect projects,here pcb companies don’t accept small gerber or pdf they only work with .pcbdoc in small boards and this is my problem to made only one of any projects for myself .but tanks lots of you,with good wishes
Sir can I use esp8266?
I use esp32
Hi sir my area not wifi..... Not code upload... How remove code From function?? Plz plz help
Hello, if you don't want to use Blynk, in the Void setup() section, please delete the part 'Blynk.begin'
Sir vsry nice posbale esp8266 same to same
Thanks i have finally compiled the code now. Further more can you make the code two phase mppt 70A, input upto 300v output auto detect from 12v to 48v system. It will enhance ur followers and more subscribers to ur channel.
Thank you for your comments,
I will add and upgrade at the next version.
@@4EProjectsChannel Thanks
It is based on Project FUGU by TechBuilder
yes, I refer there
Có bán k đại ca
dạ có nha, e cũng hay xem video của bác.
Rất hay nha
Bộ này có bán ko bạn ?
shope.ee/7pGVlW7Dk0
Hi, please reply our request. Please do complete sine wave inverter using this mcu which have menu buttons for parameter setting, LCD . 4 pwm hbridge sine wave inverter.
ok. I will research and give a tutorial
Pls send parts list
Hello, I have provided the BOM list at the link above.
Mình có nhận viết code MPPT không ạ?
Mình đã viết và chia sẻ trong video rồi nhé
Hi,good job,can you share .pcbdoc altiume file with us,tanx
Hello,
I will share
@@4EProjectsChannel tanx
I need THIS project
nice!
And with arduino nano same
Excelente video gracias
THANKS YOU :d
@@4EProjectsChannel anh có thể cho em hỏi làm thế nào để mình có thể ổn áp đầu ra khi điện áp đầu vào nó thay đổi vậy anh ? Giả sử khi mình có một tấm pin thì chỉ có Vmppt, nhưng khi mình mắc nối tiếp 2 tấm thì đầu vào là 2 Vmppt.
mình chưa hiểu ý bạn
@@4EProjectsChannelEm có 1 tấm pin mặt trời có Vmppt là 40V đầu vào còn điện áp đầu ra là 12V. Nhưng khi mình mắc nối tiếp 2 tấm pin thì Vmppt lúc này là 80V nhưng phải đảm bảo đầu ra vẫn là 12v. Anh cho em hỏi làm thế nào để mình có thể ổn áp đầu ra vẫn là 12V khi đầu vào Vmppt nó thay đổi như trên. Với trường hợp mắc như vậy thì nó có ảnh hưởng tới thuật toán dò tìm công suất cực đại không anh ?
@@tranlong2433 Nếu bạn làm như mình, Việc bạn thay đổi điện áp đầu vào thì đầu ra ổn áp theo cài đặt nhé.
the code wont compile
I can buy
u buy: shope.ee/6A88An82pF
Can u sell to indonesian?
All part list
Hello, I have provided the BOM list at the link above.
Input voltage less than value
can you write a code for me
Yes 👍 is
@@4EProjectsChannel I want 6 solar panel 330 watt 24 volt monitor on mobile and also solar charger village and current monitor
No comments? No explanations?
Hello
android app is in playstore??
app Blynk IOT
gj copy paste
i have built this one, but the problem is it cannot charge and stuck in 4Watt, any solution?
i think your current sensor is broken
@@4EProjectsChannelreally? what is the another possible causes for the issue? What about the IR2104? The IR2104 in SD and IN measured pulsing 0.8v with multimeter. Is it genuine?
А у вас заказать плату можно?
Hi @4E Projects
Firstly, Kudos to you for implementing and developing solar charge controller of 30A with ESP32. When I compiled the Arduino project in my PC, I am facing the following error due to some functions written in LCD_Menu. The project is getting compiled if I disable the charging current part in LCD_Menu code. Have you ever faced this error....??? Kindly help.
Early Response is appreciated.
'''...8_LCD_Menu:377:1: error: insn does not satisfy its constraints:
377 | }
| ^
(insn 11 2651 1185 127 (set (reg:SF 19 f0 [orig:127 _95 ] [127])
(mem/u/c:SF (symbol_ref/u:SI ("*.LC357") [flags 0x2]) [0 S4 A32])) "C:\Users\chara\Downloads\CODE_MPPT_ESP32_V1.2.1-20240819T055256Z-001\CODE_MPPT_ESP32_V1.2.1\8_LCD_Menu.ino":205:33 49 {movsf_internal}
(expr_list:REG_EQUAL (const_double:SF 0.0 [0x0.0p+0])
(nil)))
during RTL pass: postreload
C:\Users\chara\Downloads\CODE_MPPT_ESP32_V1.2.1-20240819T055256Z-001\CODE_MPPT_ESP32_V1.2.1\8_LCD_Menu.ino:377:1: internal compiler error: in extract_constrain_insn, at recog.cc:2692
Please submit a full bug report, with preprocessed source (by using -freport-bug).
See for instructions.
exit status 1
insn does not satisfy its constraints: ...'''
Thank You
Charan Sai
Hello, this error might be due to the library you're using; please check it again.