Yea I used the power steering to help me as you suggested. . Every one has a favorite way to do there u joints and I learned some hard lessons along the way . I perfer to use marine grease on the u joints and ball joints ect . I know most want do it this way but I like to use anti seize on the caps as I assembly it to help me in the future if I have to replace them again . I don't care if the solid u joints are stronger I want to grease mine . Thanks for the video
Plumbers wire brush for cleaning copper pipe for soldering with handle cut off and put into a cordless drill works awesome to clean the holes in the yolk before installing new joints
This video is sure going to help me tomorrow.. doing both sides of my 2014 3500 longhorn… I’m sure I’ll have a few more curse words tho… just sayin’🤷♂️
Try the Nebo Transcend Head lamp. 1000lumens 700 lumen 100 lumen stetting. 5hr work time 1 charge. Great for late hunts as well, can actually see 75 yards out with it
Just little tip on cleaning cap holes you can use from harbor freight small wire wheel works So fast, or Dremel wire wheel works wonders on cleaning pac-man clip tiny slot (outer clip if applicable).
I have seen another video where the guy did not remove the hub from the axle; rather, left the hub attached to the axle removing all as one. Is it better to remove the hub first or does it really matter? Thanks! Great video.
Had a question about the axle shaft being pulled out. The front right axle shaft was different than the left. Was having trouble with my breaks locking up after replacing wheel hub and pads. Replaced the caliper and brake lines and it was still being held up by what seemed to be the outer break pad. Considering I did the same thing on the left side and had no issues. Was wondering if you have attacked the right axle shaft and had any fitment issues since it’s a different sized shaft. Thanks a lot!
Sir I have had this faint rational noise and I have tried to figure out what it was and after I watched your video I cracked it! Problem solved…. Thank you!
sorry to be off topic but does someone know of a trick to log back into an instagram account?? I was stupid forgot the account password. I would love any help you can offer me
@Cameron Jesus Thanks for your reply. I found the site thru google and I'm trying it out atm. I see it takes quite some time so I will reply here later when my account password hopefully is recovered.
Yes sir! Haven't fired it up yet this season...the relay that powers the tank heater failed in March and I haven't replaced it yet. But I will be servicing it in the next few weeks. Its starting to get cold!
@@MattVerley need any www.ebay.com/itm/Retention-Head-Fin-2-Waste-Oil-Burning-or-WVO-Standard-4-set-of-2/123884080912 gladly send you couple samples :-) Since seeing your video years ago, it saved me a lot of money.. Except for the boiler going out , filter clogged, etc my small token of appreciation
@@BillyBob-fd5ht Thanks for the offer! I built a couple of retention heads out of 16GA T-304 stainless a few years ago and haven't had to change them since. I never did make any really good videos on my furnace. I built it before youtube was really a "thing" and the latest cell phone still had a flip feature :) And ditto on the money-saving thing. I've burned many thousands of gallons of waste products through my furnace, and my shop is warm all year round. Only cost is for a few watts of electricity for the preheater and blower. A great money saver!
@@MattVerley smiles, good. I like the drip oil ones on youtube. except the ignition start-up. surprised they do not make a burner same design going into a circle chamber at an angle make one swirling fire and more clean burn and less oil used.
what "whole part"? The U joint is the whole part. Or, are you referring to replacing the entire axle shaft? There is no reason to do that...the U-joint is considered a consumable part. It is carried by local auto parts stores. The axle shaft isn't considered consumable; it costs 10x as much and isn't carried by auto parts stores.
Hmmm... 70 dollar U joint, or 500 dollar axle shaft... Yaknow, those of us that aren't afraid to get a little dirt under our finger nails and know how to turn a wrench save a hell of a lot of money.
Yea I used the power steering to help me as you suggested. . Every one has a favorite way to do there u joints and I learned some hard lessons along the way . I perfer to use marine grease on the u joints and ball joints ect . I know most want do it this way but I like to use anti seize on the caps as I assembly it to help me in the future if I have to replace them again . I don't care if the solid u joints are stronger I want to grease mine . Thanks for the video
Wow probably the best video on this I've seen! Doing both mine this weekend and saving your video to refer back to. Thanks 👍
Nice work! Clear, concise, and simple. Thanks for making this. You should add a link to the u-joints you used too.
Plumbers wire brush for cleaning copper pipe for soldering with handle cut off and put into a cordless drill works awesome to clean the holes in the yolk before installing new joints
For the wheel bearing assembly leave the bolts in it but loose and hit the bolt heads with an air hammer. Walks right out.
This video is sure going to help me tomorrow.. doing both sides of my 2014 3500 longhorn… I’m sure I’ll have a few more curse words tho… just sayin’🤷♂️
Great job, thank you for sharing.
Try the Nebo Transcend Head lamp. 1000lumens 700 lumen 100 lumen stetting. 5hr work time 1 charge. Great for late hunts as well, can actually see 75 yards out with it
Just little tip on cleaning cap holes you can use from harbor freight small wire wheel works So fast, or Dremel wire wheel works wonders on cleaning pac-man clip tiny slot (outer clip if applicable).
What size is that big center nut? Do you remember, thank you.
1-11/16
Great video! But next time please note socket sizes as you use them, would be really helpful.
I have seen another video where the guy did not remove the hub from the axle; rather, left the hub attached to the axle removing all as one. Is it better to remove the hub first or does it really matter? Thanks! Great video.
Probably easier to knock out the u joint with just the axle, but the fewer the steps, the better. Do you remember the title of that video?
What is the part number for that u joint
Had a question about the axle shaft being pulled out. The front right axle shaft was different than the left. Was having trouble with my breaks locking up after replacing wheel hub and pads. Replaced the caliper and brake lines and it was still being held up by what seemed to be the outer break pad. Considering I did the same thing on the left side and had no issues. Was wondering if you have attacked the right axle shaft and had any fitment issues since it’s a different sized shaft. Thanks a lot!
I like those worklights, too, but the batteries don't last for crap. Maybe you have the newer improved version 😂
Sir I have had this faint rational noise and I have tried to figure out what it was and after I watched your video I cracked it! Problem solved…. Thank you!
Whew picked up a tip that was long forgotten with the oversize socket now just rusty c-clips and onward
Great job! Did you torque the center nut?
I heard you say something about the axle being bent or out of speck. Was your driver side axle shaft bent?
Great video, easy to follow and very helpful. Nice work.
sorry to be off topic but does someone know of a trick to log back into an instagram account??
I was stupid forgot the account password. I would love any help you can offer me
@Jonas Kenneth Instablaster ;)
@Cameron Jesus Thanks for your reply. I found the site thru google and I'm trying it out atm.
I see it takes quite some time so I will reply here later when my account password hopefully is recovered.
@Cameron Jesus It worked and I finally got access to my account again. I'm so happy!
Thanks so much, you saved my account !
@Jonas Kenneth you are welcome xD
Great video, informative, just a little bit long but, that's alright
Great video thank you sir
Great video! Thanks
What brand and psrt number did you go with for u joints?
left hand steering?
A friend of mine replaced a U joint & the new u joint was not cross drilled all the way trough & grease would go to all the cups.
It seems now days parts are just roughed in, it’s up to the consumer to inspect them and fix anything that does not work as it should.
What u joint are you using?
Totally awesome good job man
Too facken" long my guy.
👍
Matt you still using your waste furnace?
Yes sir! Haven't fired it up yet this season...the relay that powers the tank heater failed in March and I haven't replaced it yet. But I will be servicing it in the next few weeks. Its starting to get cold!
@@MattVerley need any www.ebay.com/itm/Retention-Head-Fin-2-Waste-Oil-Burning-or-WVO-Standard-4-set-of-2/123884080912
gladly send you couple samples :-) Since seeing your video years ago, it saved me a lot of money.. Except for the boiler going out , filter clogged, etc my small token of appreciation
@@BillyBob-fd5ht Thanks for the offer! I built a couple of retention heads out of 16GA T-304 stainless a few years ago and haven't had to change them since. I never did make any really good videos on my furnace. I built it before youtube was really a "thing" and the latest cell phone still had a flip feature :)
And ditto on the money-saving thing. I've burned many thousands of gallons of waste products through my furnace, and my shop is warm all year round. Only cost is for a few watts of electricity for the preheater and blower. A great money saver!
@@MattVerley smiles, good. I like the drip oil ones on youtube. except the ignition start-up. surprised they do not make a burner same design going into a circle chamber at an angle make one swirling fire and more clean burn and less oil used.
cost what, $500 in the shop? nicely done video.
i just got quoted $505.92 from the dealership for both of them... and $1102.66 with the installs.
*_RIDICULOUS_*
I was just quoted 2600 for upper and lower ball joints and wheel hub assembly. Bought the parts myself for 600.
Plenty patience
I don't understand, why you would rather work on your knees rather than use the lift that's there!!
Grease just taking the path of least resistance therefore two sides didn’t get any. Nothing you did wrong
Sir will the seller words you speak, you are no idiot.
Why wouldn't you just replace the whole Part. Cheap shit here
what "whole part"? The U joint is the whole part. Or, are you referring to replacing the entire axle shaft? There is no reason to do that...the U-joint is considered a consumable part. It is carried by local auto parts stores. The axle shaft isn't considered consumable; it costs 10x as much and isn't carried by auto parts stores.
Why would a person replace a perfectly good axle shafts? The u-joint was the issue so it's all that needed to go.
Hmmm... 70 dollar U joint, or 500 dollar axle shaft...
Yaknow, those of us that aren't afraid to get a little dirt under our finger nails and know how to turn a wrench save a hell of a lot of money.
Ahh went up to sight see the Twilight town ehh. Lol. I grew up in Port Angeles went to high school there have a lot of family that still lives there.n
Tool list?
really