Thank you for your video. What kind of push button switch do I need to use? I bought momentary switch before I didn't know. When I finished wiring only working while I keep pushing 'start button', I think I need different kind of push button switch.
youve got a wrong way to put a supply into the circuit breaker i think, supply side/incoming should be on the top side of the CB and the load side/outgoing should be on the bottom side of the CB. Do you agree?
I have a 3 phase OL I’m using on a 1 phase motor. The OL has 4 NO contacts, what do I use them for ? I can’t control the motor with the NO contacts correct ? The NO contacts have continuity(13,14). Do I need a separate contractor to make it work ?
I have seen many of your videos it's good! You have done a good job, I have a query I was searching on the net , but all don't fit the bill, I have a 3 phase 5hp water pump I need the following sensor : sump tank water level + timer on/ off , dry run - phase check. Auto on off...pls help.
You prolly dont give a shit but does any of you know of a way to get back into an instagram account..? I was stupid forgot the account password. I appreciate any tips you can offer me.
Doing some research for my job, I really wish that there were less lines. Can someone link me to the eastern european/Russian electronics? JK, this video was actually very helpful.
ek convaur motor ko start switch ek stop switch,ek emergency stop switch,ke sath el convaur ke last me tray takrane pr convaur stop ho jaye ek limit switch ,condtion h ki convaur jab bhi start kare to on switch se hi ho,esa sld koi bhai banake de sakta h kya/,ek realy use hogi sayad
I’m afraid I need to point out an error in your circuit. The very last ‘+’ (live/red) connection you made (3:15) was from contactor terminal 14 to a point BETWEEN the green start (NO) switch and the red stop (NC) switch. It was meant to be the holding/latching part of the circuit. However, because the start switch is a momentary switch as soon as it is released current cannot flow back to the contactor ie it cannot feed the holding circuit (contactor terminal A1). To correct this simply remove and replace by making a direct connection between 14 & A2.
Both switches are momentary switches? Don't quite understand " it cannot feed the holding circuit (contactor terminal A1). To correct this simply remove and replace by making a direct connection between 14 & A2." Care to explain a little?
@@jasonk8936 Apologies, i've just rewatched the vid and cannot understand why i wrote that (TBH i cant even remember writing it)🤔. I'll delete my original to not confuse anyone else 👍
@@kelargo Apologies, i've just rewatched the vid and cannot understand why i wrote that (TBH i cant even remember writing it)🤔. I'll delete my original to not confuse anyone else 👍
I think its better to show first how the control circuits works ... the stop start botton then to the magnetic coik of the contactor... then the power circuit from the mcb to the line 1 line 2 of the contactor then gojng to the motor.
Thank you for your video. What kind of push button switch do I need to use? I bought momentary switch before I didn't know. When I finished wiring only working while I keep pushing 'start button', I think I need different kind of push button switch.
youve got a wrong way to put a supply into the circuit breaker i think, supply side/incoming should be on the top side of the CB and the load side/outgoing should be on the bottom side of the CB. Do you agree?
Sir bka reversible na mcb Ang ginamit nya. Kya pwede sa ilalim Mang galing ung power supply.
thanks for this simple but clear tutorial,
You're welcome!
@@JrElectricSchool like wise bro!
Good informative video sir very thank s
Welcome
Very helpful Thank you
You're welcome!
Great stuff! Could you please give the list of magnetic contactors and and MCB used in your video?
Thanks and warmest regards.
Wow ang galing nyo po idol
Thanks for watching
Can I use modular contactor of Ac7a and Ac7b rating instead of Ac-3 rating. It will be safe to connect 2000watts single phase motor.
I have a 3 phase OL I’m using on a 1 phase motor. The OL has 4 NO contacts, what do I use them for ? I can’t control the motor with the NO contacts correct ? The NO contacts have continuity(13,14). Do I need a separate contractor to make it work ?
I have seen many of your videos it's good! You have done a good job, I have a query I was searching on the net , but all don't fit the bill, I have a 3 phase 5hp water pump I need the following sensor : sump tank water level + timer on/ off , dry run - phase check. Auto on off...pls help.
please watching this video
ua-cam.com/video/EGMH4TrNJs8/v-deo.html
Salamat sa vedio nato
Good job
Thanks
Excelente ingeniero saludos gracias
sorry i am not understand your language
please tell me Bangla,Hindi,English.
Thank you.
Thanks so good teach agan thanks
What apps did you used? Thanks
we are use animation
Thank you.
beautiful video what is the name of software that you are using
Thank you. we are using animation
Useful content
Thanks a lot
Oru mcb nine rande out kodukan patumo
sorry i am not understand
please Bangla,Hindi,English
Patum
Thanx you so much for this awesome video, but how many volt is the motor and what’s the voltage on the line coming from the panel ?
it is single phase 220v motor
@@JrElectricSchool I live in the USA and I have 2 panels 277v panel and 120v panel
Which panel do I connect it to ?
@@Savagethehome you can connect 277v
You prolly dont give a shit but does any of you know of a way to get back into an instagram account..?
I was stupid forgot the account password. I appreciate any tips you can offer me.
@Harvey Declan instablaster :)
are those available in the US? I have only been able to find availability outside the country
available in US
Y did you connect contactor no out to start and stop button between... Could you please explain brother
Doing some research for my job, I really wish that there were less lines. Can someone link me to the eastern european/Russian electronics? JK, this video was actually very helpful.
Master anu po specs ng MC mo? Tnx Nice video.
Can a bad motor causes the contactor to remain close?
What if I am using a micro switch instead of the push buttons?
Simulator kon sa ha yi sir
Nice one
Thanks 🔥
Do I need magnetic contactor for 1 hp motor?
Buena explicación
sorry i am not understand your language please tell me Bangla,Hindi,English. Thank you.
Bhai 100 amp ka 4 pole 2NO aur 2NC type contactor lagbhag kitne ka milta hai???
ape internet pe search ke g ya price ke leya
Thank you.
Can you tell me where I can get these parts at. I want to connect to to plc
USA some instances 220v is transmitted over two lines and the third line is neutral.
How do I know what size contactor I need 36 V 800 W thank you
you can use contactor 32amp for single phase motor
How to calculate magnetic conductor size?
the amp is just as much as your load magnetic contactor.
Thank you
Thank u
@@operation2303 your must welcome
Sir what is the rating of mcb and magnetic contacter
20amp MCB, 30amp magnetic contactor
Thank you
Can you say about the software ,that you are using ?
filmora wondershare,sony vegas pro,
adobe after effects,adobe premiere pro,
adobe photoshop,microsoft office.
amazing video #dtntechnology
Thanks for watching
good job
Thanks
hello, thanks for the video. Which animation program did you prepare the video with?
U should keep the line diagram on show longer.
कौन ऐप से डायग्राम बनाते हैं
supper video..how to connect devices using this softweare
Thank you. we are using animation
आप कौन सा ऐप इस्तेमाल करते हैं सर
What is the meaning of symbol L, N, E in your diagram..?
L= live /active /energised, colour= red or brown
N= neutral, black or blue
E = earth/ground, green or green and yellow
Y kesy. Bnaty ah video kon say app pe bnaty hoo
ham animation use karte he
ek convaur motor ko start switch ek stop switch,ek emergency stop switch,ke sath el convaur ke last me tray takrane pr convaur stop ho jaye ek limit switch ,condtion h ki convaur jab bhi start kare to on switch se hi ho,esa sld koi bhai banake de sakta h kya/,ek realy use hogi sayad
nice
Thanks
How to connect the overload relay with that diagram. Thank you
My single phase motor is 10hp 60A is this applicable?
please watching this video
ua-cam.com/video/m6-s-yGP8q4/v-deo.html
Super sir
Thank you
Sir ak video banaeye timer ke on delay timer ke sath motor ko kaise control karte hai
begart tona na kame por to nahi ky
Why u take no coil?
Good
Thanks
Sir where you takes picture of electric components
Nice
Thanks
👍
Thanks for watching
Thank you
समझ में नहीं आया
ভাই কেপাছিটার কি ভাবে লাগাই, ভি ডি ও দিবেন ৫ হ্্জ
i will try to make video on your topic.
Thank you.
I’m afraid I need to point out an error in your circuit. The very last ‘+’ (live/red) connection you made (3:15) was from contactor terminal 14 to a point BETWEEN the green start (NO) switch and the red stop (NC) switch. It was meant to be the holding/latching part of the circuit. However, because the start switch is a momentary switch as soon as it is released current cannot flow back to the contactor ie it cannot feed the holding circuit (contactor terminal A1). To correct this simply remove and replace by making a direct connection between 14 & A2.
I tried this. It causes a short. The diagram at the end works as desired.
Both switches are momentary switches? Don't quite understand " it cannot feed the holding circuit (contactor terminal A1). To correct this simply remove and replace by making a direct connection between 14 & A2." Care to explain a little?
@@jasonk8936 Apologies, i've just rewatched the vid and cannot understand why i wrote that (TBH i cant even remember writing it)🤔. I'll delete my original to not confuse anyone else 👍
@@kelargo Apologies, i've just rewatched the vid and cannot understand why i wrote that (TBH i cant even remember writing it)🤔. I'll delete my original to not confuse anyone else 👍
@@stuffoflardohfortheloveof No worries. I too dont remember anything anymore after the vax
App kun sa istemal karte sir
me kus samja nehe ?
Sirji, agar explanation kardiya hota toh aur bariya hota
Thank you so much for share your opinion
i will try
👍🏼👍🏼
Thanks for watching
This contackter name
Sir i want joint school
please you can subscribe our channel and joint free.
Thank you.
தமிழ் வீடியோ போடுங்க
Theory ke sath
ha
thanks for watching
I think its better to show first how the control circuits works ... the stop start botton then to the magnetic coik of the contactor... then the power circuit from the mcb to the line 1 line 2 of the contactor then gojng to the motor.
If my contactor works with 220 volt .. i only feed bye one líne .. in other words i feed only bye A2... the bobine only have one líne
wow
Thanks
nc
Thanks
mas mahirap pa redstone mechanics ng minecraft eh ez lang pala to.
Sir yung may overload relay panu po wiring
sorry i am not understand your language please tell me Bangla,Hindi,English.
Thank you.
Schneider Electric Square D TELEMECANIQUE TeSys LC1D12BD
Music is horrendous. Video is worse
nv
good job
Thanks