It would be cool if we could mirror either a pc screen or a phone screen into the goggles so that we could play Sims through the goggles I feel that would help a lot with practicing manual mode.
I noticed that while you were going through all the settings in the Goggles 3 you weren’t connected to a controller. If I am flying my Air 3 drone using my RC 2 controller may I have all my settings that are already in the RC 2 and use them or do I have to reset them all in the Goggles 3?
How long does the Goggles, take to charge? I've been charging them for over two hours, with a 20w charger. I have a 65w charger charging my Avata 2 batteries, & 2 are already fully charged & the 3rd one is halfway done. I thought the Goggles would have taken less time, I still need to charge my Motion 3 controller. It doesn't seem to take this long, to charge my Goggles Integra.
Interesting, that seems defective as per your description. Have you turned them on to check the battery level and see if they hold charge? Try updating the firmware.
If you just bought them then yeah take them back get a refund and get the Googles 3. If you can’t don’t stress. There’s no firmware yet for backward compatibility we’re still waiting on that.
@@DimmyV for the sake of o4? I don't fully understand. Firmware for the integra to be fully compatible with air 3 or goggles 3 to be updated for full compatibility with Air 3? And again, Only reason I can think of an upgrade is the O4 transmission, if that really makes a difference in connectivity? What other benifit is there with O4? Range, transmision data (not video quality?), stability of connectivity. What else?
Great video thank you! Bit confused about max flight distance, I know re the height in UK set to 400ft but what should we set max flight distance to please? Unlimited?
Height and distance are both different. Distance should be within Visual Line of Sight but outside of cities you can likely fly further as less obstacles and interference. Max height would be 400ft but again there’s ways you can fly higher within regulations each vary per jurisdiction.
Ok so, What I would like to know how to do is have audio in both the drone and goggles recordings. I know how to get audio on the other dji drones using the screen controllers but, i'm having a hard time doing that with the goggles 3
@@DimmyV Mini 2, Mini 3 Pro, Mini 4 Pro. It was all very easy to do from the controller. You could screen record with a wireless mic plugged into the usb-c port and have audio with the drone footage
@ ah yes ok, the DJI RC2 will do this. I thought you mean from drone itself. Only thing I can think of to try is using a DJI mic and using an audio and visual sync. One for DJI to integrate.
Does any other non dji drones work with the googles 3? I'm learning to fly manual and would like to learn on a cheaper drone first, since I know it's going to end poorly the first few flights. I'm a few hours into liftoff simulator and still pretty rough.
At the moment no. Eventually I imagine there will be a firmware update. You probably better off with Goggles 2 atm. If you wanted a cheaper quad I recommend a Tinywhoop kit. The BetaFlight Cetus x or the Emax TinyHawk 2 are good options. Keep practicing in the sim. Even when you’re flying in real life rainy days when you want to fly sim is a good way to hone your skills
@DimmyV Would it be correct to assume if the googles 3 only currently works with DJI products, the RC3 is the same until a future firmware update also?
@scoobydew420 yeah for now. I’m literally waiting myself so I can use it with the GEPRC Mark 5 which is the O3 air unit. Also would like compatibility with RunCam Wasp. Just a waiting game 🫖
When I'm taking off around a lot of people and also landing, it will be nice to use the pass through to make sure I'm clear of people and objects. We will see ?
Good question. I didn’t get a chance to m include but I have done in my upcoming video. Essentially it’s your downward sensors telling you how close you are to the ground.
Sir , my goggles is already connected however when i double tap to see realview nothing happens. Also when I tried to connect the motion control and then there's a part there where you have click the dial twice in order to proceed its nothing working. I hope someboby here can help me. Its my firstime using dji avata 2 and first time drone. So i really have no idea. I just follow what then videos are showing. When I pull the accelarator to click or to proceed its not working.
How can I recentre or trim the view when using head tracking between my Mini 4 pro and Goggles 3+RC Motion 3? I'm finding that the camera is pointing too far down when my head is level and I'm having to look too far up to compensate. The side to side is also slightly off. I've recalibrated the Goggles IMU and M4P camera gimbal but it makes no difference. Really there needs to be a mechanism to recentre or trim the camera to personal preference. I had thought the RC Motion 3 scroll wheel might act as a trim but no. Any thoughts? I've been through all the settings I can find.
@@DimmyV Thanks. I think a demo is needed on the best way to calibrate the Goggles IMU. I tried it yesterday with the goggles on my head (apart from the last orientation which is upside down). I think that has helped my issue but ability to "trim" the camera is what's really needed. The obvious way to achieve that is with the RC Motion 3 scroll wheel if DJI can implement that. ua-cam.com/video/SU70qG7uN-w/v-deo.htmlsi=0QoVqVlersIqrj2E
The one point I did not mention that I thought of after I shot the video is the ability to play the DJI sim by just plugging in your phone to the goggles. That way we won't need to be by a computer and have the Goggles experience. Id love it if it was compatible with other sims too. @dji can we get a firmware update for this to work.
@@DimmyV mini pro 4, i saw if you turn goggles off it reverts back to controller, I cannot pair my goggles so far I can only fly with RC, i cannot load fly ap on s23 as it says the app is for older android, installed on ipad, software run but cannot pair with drone.
@@DimmyV nope lol I try using ipad, first thing, if you dont use cable from goggles nothing will work at all, next I powered controller to see if it made difference, it did firmware upgrade, then at least i could fly with rc. Re tried goggles pairing, this time after restart of the fly ap it said firmware needs updating, which took 10 minutes, then restarted ap and devices and now it said register goggles which I did , then it said pro 4 wishes to join the network so I did that and so thought now it would work, but, nope goggles still constant beeping and timeout after 60 seconds, can see in goggles connecting to pro 4 but times out. Then ap sayd ensure device is powered on and in pair mode. I presume this is done b the power on and hold 3 secs for the beep. Did all this and goggles still wont pair !! WIll try DJI forum
Appreciate the feedback I’ll take this into account but I have to find the right balance between making the information clear and not having a very long video.
Hello everyone! Great goggles 3 🔥 Unless there is a problem... Avata 2 pack purchased in April, 3/4 uses, the goggles no longer charge "headphone battery overheating" If anyone has ever had this problem...🙄
Δημήτρη γεια σου και πάλι.Απο το απόγευμα που τα εχω,δεν μπορώ να καταλάβω πως τα κανω link με το RC2 controler,για να μπορεσω να τα κανω activate.Εχουν μείνει εκεί μετα το tutorial και δεν μπορω να κανω firmware update,αφου η dji λεει να το κανω connect με τηλεφωνο κι απο εκει μεσω του fly app.Οταν εχεις ομως το RC2 που εχει built in το app,πως γίνεται????Please assist....
Βεβαιωθείτε ότι όλα είναι ενεργοποιημένα, κρατήστε πατημένο το κουμπί λειτουργίας στο Goggles για 5 δευτερόλεπτα και στη συνέχεια το RC3 για 5 δευτερόλεπτα. Όταν σταματήσει το ηχητικό σήμα, θα πρέπει να συνδεθούν. Πρέπει να κάνετε το ίδιο με το Avata 2 και το RC3. Για να ενημερώσετε το υλικολογισμικό, όλα πρέπει να είναι συνδεδεμένα και το τηλέφωνο να είναι συνδεδεμένο στο Goggles.
@@DimmyV Καλημέρα Δημήτρη,τελικά κατάφερα να τα κάνω λινκ με το RC2 και το AIR3.Αυτό που δεν έχω καταφέρει ακόμα είναι το live view.Οσο και να χτυπαω με τα δάχτυλα στην δεξια πλευρά των googles,δεν μπορω να δω μπροστα μου....
Hello I need help🤚 the goggles screen says that the headset is not connected but i am stuck here because the 5d button has no effect. Do you know what to do?
You need to sync the drone to Goggles with both devices on hold the power button on goggles first for 5s till it starts beeping. Then hold the power button on drone for 5s until it starts beeping. When the beeping stops they should be synced. You will need to do same between with Goggles and Controller after.
@@DimmyV thank you for your answer. M'y problème is that is impossible to exit of the window "the helmet is Not connected limited fonction" because the 5d Button has no effect. I Turned Off and on but nothing change.
Big let down not been able to link to TV or vr when not flying any idea on how we could do this ? Got WiFi built in so shouldn't be a problem also having to keep your phone connected uk cumbersome
noice. but how did you get the 03 air unit to work with the goggles v2? Would really like to see how you get 03 air unit working on the goggles 3 also.
Can anyone help me. I have 1 Extreme Pro microSD Card. The sd card can be seen on the Avata 2 but not seen when i insert it to the Goggles 3. Does it not work if it is just inserted in the Goggles 3. Do I need 2 sd cards at the same time?
Interesting, have you tried switch the cards from Avata 2 with goggles and see if it’s a faulty card? You can use 2 SD cards. One will film from Avata 2 the other will record Goggles OSD
@@ironblade91 after testing this did not work. I did a Google search many others confirmed did not work. Would be nice update though. Watch movies on a plane etc
I actually find these really comfortable. The surrounding pad isn’t needed as it rests on forehead rather than face. Way more comfortable than v2. I’m glad the googles 3 can use O3 now. I need to update my mark 5 to try
My apologies this may be an error on my part. Because the way the controller connects to the Goggles. Controller 3 is a Bluetooth connection to goggles 3 which connects to drone. The Googles 2 and controller 2 independently connect to drone. Unless there’s a firmware update I don’t believe the googles 2 can work with goggles 3. I hope you can prove me wrong.
I got my Avata 2 today and the weather is terrible here too. So I thought I'd take the time to research all of the menus. Thanks for the guide! When I have bad weather sometimes I vacuum and mop the floors, then dry them by cruising around the house with my drones 😂
dji is NOT stopid. They know what they are doing, and they do make the headset camera worse by design. So they can improve it next year again and sell again more.
It would be cool if we could mirror either a pc screen or a phone screen into the goggles so that we could play Sims through the goggles I feel that would help a lot with practicing manual mode.
Yes. Ideally would love to just connect to phone via the app and fly with the controller.
Do you connect the Goggles with your iPhone directly with an USB-C cable or the the “dongle” comes with (OTG) ?
Direct via USB
I noticed that while you were going through all the settings in the Goggles 3 you weren’t connected to a controller.
If I am flying my Air 3 drone using my RC 2 controller may I have all my settings that are already in the RC 2 and use them or do I have to reset them all in the Goggles 3?
Made a video on it. It should explain my findings ua-cam.com/video/UJhrTOVhnAM/v-deo.htmlsi=3tLbIUljl2fxClOf
finding it impossible to swipe the goggles 3 tp cause a new screen to appear. Any suggestions?
“New screen” ? What do you mean by that.
Can u setup head tracking using o3 camera setup on a plane get camera to turn.
Interesting, I don't have a place but if someone who reads this in the community would like to answer please feel free.
How do we record the screen for goggles 3 itself before connecting to the drone and or before flying?
Easiest way is to connect phone and screen record.
hi can you use glassers with the dji goggels john nottingham
It has built in adjustments so you just need to use the knobs underneath to adjust to your vision.
How long does the Goggles, take to charge? I've been charging them for over two hours, with a 20w charger. I have a 65w charger charging my Avata 2 batteries, & 2 are already fully charged & the 3rd one is halfway done. I thought the Goggles would have taken less time, I still need to charge my Motion 3 controller. It doesn't seem to take this long, to charge my Goggles Integra.
Interesting, that seems defective as per your description. Have you turned them on to check the battery level and see if they hold charge? Try updating the firmware.
@DimmyV They charged up & work ok, with a 20w charger, they took about 2 & half hour's. The batteries for the Avata 2 took about 48 minutes each.
Hi, the intro of your movie I see Googles 3 instead of Goggles 3. I think it's a good idea to adjust this. ;-)
Appreciate it. I have to live with this as it’s in the edit. 🍻
Would you say goggles 3 o4 is worth upgrading from the integras 03+? I intend to fly the Air 3 with integra. Haven't opened the Integra goggles yet...
If you just bought them then yeah take them back get a refund and get the Googles 3. If you can’t don’t stress. There’s no firmware yet for backward compatibility we’re still waiting on that.
@@DimmyV for the sake of o4? I don't fully understand. Firmware for the integra to be fully compatible with air 3 or goggles 3 to be updated for full compatibility with Air 3? And again, Only reason I can think of an upgrade is the O4 transmission, if that really makes a difference in connectivity? What other benifit is there with O4? Range, transmision data (not video quality?), stability of connectivity. What else?
Great video thank you! Bit confused about max flight distance, I know re the height in UK set to 400ft but what should we set max flight distance to please? Unlimited?
Height and distance are both different. Distance should be within Visual Line of Sight but outside of cities you can likely fly further as less obstacles and interference. Max height would be 400ft but again there’s ways you can fly higher within regulations each vary per jurisdiction.
@@DimmyV thanks for replying, yeah I am mainly flying in open countryside etc
Ok so, What I would like to know how to do is have audio in both the drone and goggles recordings. I know how to get audio on the other dji drones using the screen controllers but, i'm having a hard time doing that with the goggles 3
I've never had audio from the Goggles 3 to my knowledge. What drones were you recording audio from in past?
@@DimmyV Mini 2, Mini 3 Pro, Mini 4 Pro. It was all very easy to do from the controller. You could screen record with a wireless mic plugged into the usb-c port and have audio with the drone footage
@ ah yes ok, the DJI RC2 will do this. I thought you mean from drone itself. Only thing I can think of to try is using a DJI mic and using an audio and visual sync. One for DJI to integrate.
Id like to see heading in degrees so i can navigate via ifr
Ooo that’s a good one.
Does any other non dji drones work with the googles 3? I'm learning to fly manual and would like to learn on a cheaper drone first, since I know it's going to end poorly the first few flights. I'm a few hours into liftoff simulator and still pretty rough.
At the moment no. Eventually I imagine there will be a firmware update. You probably better off with Goggles 2 atm. If you wanted a cheaper quad I recommend a Tinywhoop kit. The BetaFlight Cetus x or the Emax TinyHawk 2 are good options. Keep practicing in the sim. Even when you’re flying in real life rainy days when you want to fly sim is a good way to hone your skills
@DimmyV Would it be correct to assume if the googles 3 only currently works with DJI products, the RC3 is the same until a future firmware update also?
@scoobydew420 yeah for now. I’m literally waiting myself so I can use it with the GEPRC Mark 5 which is the O3 air unit. Also would like compatibility with RunCam Wasp. Just a waiting game 🫖
@DimmyV Seems like I should just practice on the sim for now until I can scoop up something that works with my current DJI gear. Thanks man!
When I'm taking off around a lot of people and also landing, it will be nice to use the pass through to make sure I'm clear of people and objects. We will see ?
Yes that’s a useful feature though I still wish it was implemented better with wider field of view
Καλημέρα Δημήτρη,υπάρχει κανένα θέμα με τα μάτια αν κάποιος φοράει γυαλιά για να βλέπει κοντά???
Γεια σου Άκη, το Goggles 3 συνοδεύεται από προσαρμογείς και μπορείς να κάνεις προσαρμογές στην όρασή σου χρησιμοποιώντας τα χειριστήρια από κάτω.
@@DimmyV Σε ευχαριστώ Δημήτρη,μόλις τα αγόρασα και τα φορτίζω για να κάνω τις ρυθμίσεις.
What is the changing number in the lower center of the goggle view. a number with arrow and changes from red to yellow to white as your flying
Good question. I didn’t get a chance to m include but I have done in my upcoming video. Essentially it’s your downward sensors telling you how close you are to the ground.
OK, thank you for the quick response. I recently bought one, and that's what I was thinking. You gained another follower.
Sir , my goggles is already connected however when i double tap to see realview nothing happens. Also when I tried to connect the motion control and then there's a part there where you have click the dial twice in order to proceed its nothing working. I hope someboby here can help me. Its my firstime using dji avata 2 and first time drone. So i really have no idea. I just follow what then videos are showing. When I pull the accelarator to click or to proceed its not working.
Try rebooting the googles and see if that works, reboot all devices. I know rearview is finicky sometimes and you have try more than once.
How can I recentre or trim the view when using head tracking between my Mini 4 pro and Goggles 3+RC Motion 3? I'm finding that the camera is pointing too far down when my head is level and I'm having to look too far up to compensate. The side to side is also slightly off. I've recalibrated the Goggles IMU and M4P camera gimbal but it makes no difference. Really there needs to be a mechanism to recentre or trim the camera to personal preference. I had thought the RC Motion 3 scroll wheel might act as a trim but no. Any thoughts? I've been through all the settings I can find.
Very interesting, this was a test for me but next time I fly outside I’ll have a look. I’m planning on an indoor video next
@@DimmyV Thanks. I think a demo is needed on the best way to calibrate the Goggles IMU. I tried it yesterday with the goggles on my head (apart from the last orientation which is upside down). I think that has helped my issue but ability to "trim" the camera is what's really needed. The obvious way to achieve that is with the RC Motion 3 scroll wheel if DJI can implement that.
ua-cam.com/video/SU70qG7uN-w/v-deo.htmlsi=0QoVqVlersIqrj2E
Hello, how are you? Please, how do I calibrate Googles 3? I've tried several times and I can't.
What do you mean by calibrate, what are you trying to achieve? This will help me give you better guidance. Thanks
can i use goggle 3 with o3 air unit?
Not yet, I'm also waiting for this
You can now! Thankfully they finally updated it to work with the o3. I just bought a set thanks to that.
Yup I saw Mads Tech video but won’t be able to do this until I’m in Cyprus.
The one point I did not mention that I thought of after I shot the video is the ability to play the DJI sim by just plugging in your phone to the goggles. That way we won't need to be by a computer and have the Goggles experience.
Id love it if it was compatible with other sims too. @dji can we get a firmware update for this to work.
tbh dji sim sucks
I presume you can turn off goggles to revert to controller to see landing better?
Are you referring to flying a regular Mavic drone or FPV?
@@DimmyV mini pro 4, i saw if you turn goggles off it reverts back to controller, I cannot pair my goggles so far I can only fly with RC, i cannot load fly ap on s23 as it says the app is for older android, installed on ipad, software run but cannot pair with drone.
@@davidmills6916 This video may help: ua-cam.com/video/UJhrTOVhnAM/v-deo.html
@@DimmyV nope lol I try using ipad, first thing, if you dont use cable from goggles nothing will work at all, next I powered controller to see if it made difference, it did firmware upgrade, then at least i could fly with rc. Re tried goggles pairing, this time after restart of the fly ap it said firmware needs updating, which took 10 minutes, then restarted ap and devices and now it said register goggles which I did , then it said pro 4 wishes to join the network so I did that and so thought now it would work, but, nope goggles still constant beeping and timeout after 60 seconds, can see in goggles connecting to pro 4 but times out. Then ap sayd ensure device is powered on and in pair mode. I presume this is done b the power on and hold 3 secs for the beep. Did all this and goggles still wont pair !! WIll try DJI forum
@@davidmills6916 contact DJI support they have improved over the years. Sorry you’re experiencing all this. Very odd
I wish I could listen as fast as you talk.
Appreciate the feedback I’ll take this into account but I have to find the right balance between making the information clear and not having a very long video.
You can also use the UA-cam's functionality to slow down videos from Settings > Playback Speed.
@@DimmyVlol I chuckled at the comment but you’re good. You speak at an appropriate rate, no need to change anything.
Hello everyone!
Great goggles 3 🔥
Unless there is a problem...
Avata 2 pack purchased in April, 3/4 uses, the goggles no longer charge "headphone battery overheating"
If anyone has ever had this problem...🙄
“Headphones” ? Have you contacted DJI Support?
Δημήτρη γεια σου και πάλι.Απο το απόγευμα που τα εχω,δεν μπορώ να καταλάβω πως τα κανω link με το RC2 controler,για να μπορεσω να τα κανω activate.Εχουν μείνει εκεί μετα το tutorial και δεν μπορω να κανω firmware update,αφου η dji λεει να το κανω connect με τηλεφωνο κι απο εκει μεσω του fly app.Οταν εχεις ομως το RC2 που εχει built in το app,πως γίνεται????Please assist....
Βεβαιωθείτε ότι όλα είναι ενεργοποιημένα, κρατήστε πατημένο το κουμπί λειτουργίας στο Goggles για 5 δευτερόλεπτα και στη συνέχεια το RC3 για 5 δευτερόλεπτα. Όταν σταματήσει το ηχητικό σήμα, θα πρέπει να συνδεθούν. Πρέπει να κάνετε το ίδιο με το Avata 2 και το RC3. Για να ενημερώσετε το υλικολογισμικό, όλα πρέπει να είναι συνδεδεμένα και το τηλέφωνο να είναι συνδεδεμένο στο Goggles.
@@DimmyV Καλημέρα Δημήτρη,τελικά κατάφερα να τα κάνω λινκ με το RC2 και το AIR3.Αυτό που δεν έχω καταφέρει ακόμα είναι το live view.Οσο και να χτυπαω με τα δάχτυλα στην δεξια πλευρά των googles,δεν μπορω να δω μπροστα μου....
Hello I need help🤚 the goggles screen says that the headset is not connected but i am stuck here because the 5d button has no effect. Do you know what to do?
You need to sync the drone to Goggles with both devices on hold the power button on goggles first for 5s till it starts beeping. Then hold the power button on drone for 5s until it starts beeping. When the beeping stops they should be synced. You will need to do same between with Goggles and Controller after.
@@DimmyV thank you for your answer. M'y problème is that is impossible to exit of the window "the helmet is Not connected limited fonction" because the 5d Button has no effect. I Turned Off and on but nothing change.
@pierrebussien553 would contact DJI maybe it’s a defect unit
@@DimmyV thank you for your answer
If you made it to the end for my wish list what else would like improved with the Goggles 3?
Big let down not been able to link to TV or vr when not flying any idea on how we could do this ? Got WiFi built in so shouldn't be a problem also having to keep your phone connected uk cumbersome
Excelente vídeo! Você tem ótima didática e seu conteúdo é bastante completo. Abraços do Brasil 🇧🇷
Thank you 🍻
noice. but how did you get the 03 air unit to work with the goggles v2?
Would really like to see how you get 03 air unit working on the goggles 3 also.
The v2 are compatible with O3, we are just waiting for Goggles 3 to be compatible with O3.
Update firmware
@Usnveteranstacker I have just haven’t had chance to test.
Can anyone help me. I have 1 Extreme Pro microSD Card. The sd card can be seen on the Avata 2 but not seen when i insert it to the Goggles 3.
Does it not work if it is just inserted in the Goggles 3. Do I need 2 sd cards at the same time?
Interesting, have you tried switch the cards from Avata 2 with goggles and see if it’s a faulty card?
You can use 2 SD cards. One will film from Avata 2 the other will record Goggles OSD
@@DimmyV I dont think it's a faulty card since it works perfectly fine when it's inserted to the Avata 2.
@@andre785 try another card in Goggles 3, maybe they have a fault. Or try reformatting the card
ok I'm back again. how to stream videos from my phone to the googles 3?
DO you means stream from Goggles to your Phone?
@@DimmyV phone to goggles
@@ironblade91 after testing this did not work. I did a Google search many others confirmed did not work. Would be nice update though. Watch movies on a plane etc
@@DimmyV tyvm man much appreciated, keep uploading quality vids like this! cheers!
how to unlock and lock the diopter?
Twist and Pull down. Then adjust, The push in and twist to lock
@@DimmyV can you make a short video for it maybe reels so I can follow pls tyvm
Μπράβο σου Δημήτρη, τοπ βίντεο!
Eυχαριστώ 🍻
Wishlist.... A Good aftermarket face pad/foam.
I actually find these really comfortable. The surrounding pad isn’t needed as it rests on forehead rather than face. Way more comfortable than v2. I’m glad the googles 3 can use O3 now. I need to update my mark 5 to try
Thank you for this great job.
First video I have seen that says it works with Controller 2
My apologies this may be an error on my part. Because the way the controller connects to the Goggles. Controller 3 is a Bluetooth connection to goggles 3 which connects to drone. The Googles 2 and controller 2 independently connect to drone. Unless there’s a firmware update I don’t believe the googles 2 can work with goggles 3. I hope you can prove me wrong.
I couldn’t find the part where it shows you how to calibrate the goggles
What are you trying to calibrate? The controller?
Great info
Glad it was helpful
Great review! 👍
Appreciate it 🍻
Really annoyed me after buying the Avata 2 that the goggles didn’t work with a simulator
I got my Avata 2 today and the weather is terrible here too. So I thought I'd take the time to research all of the menus. Thanks for the guide!
When I have bad weather sometimes I vacuum and mop the floors, then dry them by cruising around the house with my drones 😂
Glad you found the video useful. Also what a great idea 😂 I didn't more the floors so all the surfaces got blasted with dust.
You’re not alone in your lack of proofing your content when it comes to Goggles to Googles 😂ive come across this over five times….
I try my best, but sometimes things slip through cracks, only human 😂
For a man of 66 this all seems very hard to work out
Shame all the settings cannot be done in the fly app and just use the goggles to fly
Appreciate the insight of this, I said the same when using the Goggles 3 with Air 3. Some features missing and usability.
dji is NOT stopid. They know what they are doing, and they do make the headset camera worse by design. So they can improve it next year again and sell again more.
Very true 💸
Down Below 👍
🙌🏼