I am so new to this hobby, just built my first drone and got my goggles integra, I wasnt getting any OSD elements from beta flight until I fillowed this guide, thanks very much.
You're a life saver Joshua (again)! My OSD elements were offset on my latest (first O3) build so I was wracking my brain trying to figure out the root cause. I was actually searching for the correct O3 canvas width/height settings to use in my CLI when I stumbled across your video. I had copied all of my OSD settings from my last BF4.4 Vista build so that explains why I had the wrong BF canvas settings. Thanks for explaining the changes for O3 .... including the change from 'normal' to 'HD' canvas mode that I need to make in my goggles. All working correctly now. Thx again ... I learned something today 👍
FYI: if you update the v2 goggles with the newest firmware to enable the HD canvas mode and have an avata that you haven’t updated with the RID firmware you will get an error that says incompatible goggles firmware but the Avata will still fly just fine. You can clear the error in the Status menu. I updated my v2s last Saturday and set up the HD OSD in bf4.4, chose the DJI HD preset, and didn’t have to do anything in the CLI. It works fantastic. I flew four packs with the O3 air unit and two batteries with the Avata with zero issues. I’m assuming the preset took care of the CLI stuff JB did because I sure as hell didn’t do any of that and it worked perfectly. Thanks for the vid, JB.
Thanks so much.. I asked someone else a few weeks ago why my cross hairs on my Pavo Pico were off to the right on my OSD. They told me to make sure the OSD was on HD. Which it was in Betaflight. They didn’t tell tell me to go into my goggles and change the settings in my goggles. Love the way you explain FPV.
In case anyone gets the warning message “Incompatible goggles, air unit and camera” which happens if you swap just the camera or just the vtx (they come calibrated together from the factory..) you will need to plug it in to Dji assistant 2-Consumer Drone version, and calibrate them. In this case you have to connect to power. Then after you plug in power, a pop up will automatically ask you if you would like to calibrate the camera, and you choose yes. Only takes a few seconds, and it’s all good. I went through this after shearing the m1.6 screws on one of my o3’s, and swapping it out.. just something to keep in mind..
@@SikhFPV Perhaps if doing so from the beginning, but the screws hold the two halves from falling apart as well. Using VHB would only be securing the bottom metal cover. You could argue that zip ties would solve that issue, but that was my first o3 build. No idea what the heat was going to be like. Easier to just swap it out and order screws and replace. Rather than gambling on ruining a brand new $170 vtx.
Hey joshua, do you think you could make a “refresher “ video for ppl that have been out of the hobby for a long time? Like covering the basics and some of the new stuff? 🙏🏼
@joshuabardwell This would be amazing.. as someone that took a break right before the whole FrSky Acsst change thing, and is now getting back into it, it’s all very different! All my quads still run 4s on F3 fc’s!
Thank you so so much! This helped me solving my complete problem with O3 and learning a lot about it in a few minutes! I've been searching for the fitting files to load from local space, but found no presets in the internet for DJI O3. -.-
Dang JB...u saved my butt again! I was having big time issues trying to figure this out. Many thanks!! BTW...became a patreon subscriber today. Stay safe brother.
Yes but you still usually have to set osd_displayport_device manually because DJI didn't implement the full vtx-FC communication protocol. Currently, only WTFOS is 100% sure that you don't have to manually put that CLI line in.
😀 This is just the information I was looking for! Only, I'll be sure to set my width and height to 53 and 20 so I don't have a tall narrow FOV like you just set. 09:07 😁
This should help make it easier for people to set up o3 in betaflight. definitely annoying when I tried to enable HD as an early adopter in BF 4.3 with o3 and it didn't work. dunno if I really want it smaller now I'm used to it and it didn't look that bad lol. not that big of a deal for me.
Can these different onscreen displays be edited using Betaflight with a DJI Avata 2? I'd love to be able to edit what is shown and where if possible or does DJI lock all that down on their own drones? Many thanks.
Hey, there's some voodoo with my Vista nad V2 googles going on. I have WTF, and HD OSD workson every quad with ori dji air unit, but on Flywoo Firef;y Baby with Vista, I can't turn on the HD option is osd tab. As soon as I click it, it goes back to auto, ntsc or pal...
Can I use different dji cameras with the air unit 3 like the wasp or pheonix or nebula with the unit 2 and if I am able to is it possible to switch between the cameras quickly while I'm already our flying if I have both the original 03 camera and another one? Also which current dji cam is best for low light but still have good picture/resolution?
So I've done all this it works fine but with HD canvas on I get HORRENDOUS range like 25ft. It is going out of low power mode. It asks works great if I have HD canvas mode off and msp off in ports tab. Switch either of those on and I get no usable range.
Супер відео, екранне меню в Гугл 2 запрацювало так як треба в INAV 7.1.0. Дякую! Ще б з компасом розібратись, ні як не можливо нормально відкалібрувати.
Just got iNav OSD working with my O3 Air and Goggles 2. Has there been a fix yet for the "?" character that is seen on screen instead of the proper characters as seen in iNav config?
I started using Fettec FC with kiss firmware, and I am only can see the voltages, I am wondering if this is DJI lacking for support or is kiss problem, I might not even try kiss anymore.
Hi Josh, new to BF and still learning... I've come from DJI drones - My question is what if my BNF preset im using for my nazgul F6 V2 required 4.3.2 firmware to be flashed to use, can i still do this? Or because im using the 4.3.2 preset i can't? Thanks
Hey mate, I havent heard you talk about this but i know you know it all about fpv :) can you only have one additional working msp selected in the PORTS tab?(apart from usb) i have the one you must keep on which is USB then i have the uart my 03 air unit goes through and osd works fine but when i select msp for the uart my onboard FC bluetooth goes through my osd stops working and BT also doesnt work unless i turn off uart for 03 air unit :( how annoying, I jus wanna tune my quad without my computer at the park with osd.
Hello, thank you for the video. However I have an issue, I have followed all the steps but when I connect the battery and put the goggles, I don't have any OSD information on my screen... Can someone please help me? Thank you
No osd stays wide , I don't mind wide elements in 4:3, things on edges are a bit harder to see (goggles 2)but I just keep important stuff near the center anyways
Help! DJI 03 canvas mode does not work. I've pretty much exhausted all ideas to get the OSD working on my goggles 2. No OSD information is displayed at all. The full camera image is displayed with the base DJI information: Betaflight 4.4.1 DJI Goggles: V01.05.0000 DJI Air Unit: V01.02.0000 Crossfire latest version Mamba F722_2022B flight controller Flight Controller factory connector uses Uart4 to connect to DJI air unit Peripherals dropdown set to VTX (MSP+Displayport) on Uart4 with Configuration/MSP slider on OSD Option on Configuration page slider on Video format on OSD page set to HD DJI Goggles 2 display option set to HD osd_canvas_width = 53 osd_canvas_height = 20 osd_displayport_device = MSP DJI 03 RX connected to flight controller TX DJI 03 TX connected to flight controller RX Any ideas would be helpful. Thanks
Hey Josh, I did everything you mentioned and managed to get all my OSD up on my goggles 2, except for GPS-related displays. Any idea how to fix this? Thank in advance!
@@kylespencer4037 hey bro. I found the issue alr. Are you using o3 air unit that connects directly to your fc with a connector? What radio are you using?
@@kylespencer4037 ok your gps might be connected to the same uart as your sbus wire from the dji o3. Just try a different uart for your gps. For me im using elrs so i just had to take that yellow wire out.
@@JoshuaBardwellv2s are rotted with Wtfos installed. I want a 03 to get sound in my flight videos. Also can I still use Wtfos to add OSD to my 03 flights like my vista lite
O3 does not record sound sorry to say. V2 goggle can be used with O3. To do this, you switch the goggles into "O3 mode" in the menu. When v2 is used with O3, WTFOS does not apply. It is not relevant. It doesn't exist. When the goggles are in O3 mode, the entire concept of rooting and WTFOS doesn't exist. It has no effect at all. If you want to record your OSD, either use a Vista with V2 and WTFOS, or use Goggles 2, which can record OSD internally.
This is the only video on the internet that actually explains how to get the OSD working. Thanks Josh!
Thanks! I couldn't make this hobby work without you. You're everything to me. Seriously! You learned something today, haha!
2:08 "sort of" is the DJI's motto when it comes to supporting DIY FPV features
Yeah even at that they cant be beat
I am so new to this hobby, just built my first drone and got my goggles integra, I wasnt getting any OSD elements from beta flight until I fillowed this guide, thanks very much.
set osd_canvas_width = 53
set osd_canvas_height = 20
save
that was my problem!
Thank you!
You're a life saver Joshua (again)! My OSD elements were offset on my latest (first O3) build so I was wracking my brain trying to figure out the root cause. I was actually searching for the correct O3 canvas width/height settings to use in my CLI when I stumbled across your video. I had copied all of my OSD settings from my last BF4.4 Vista build so that explains why I had the wrong BF canvas settings. Thanks for explaining the changes for O3 .... including the change from 'normal' to 'HD' canvas mode that I need to make in my goggles. All working correctly now. Thx again ... I learned something today 👍
FYI: if you update the v2 goggles with the newest firmware to enable the HD canvas mode and have an avata that you haven’t updated with the RID firmware you will get an error that says incompatible goggles firmware but the Avata will still fly just fine. You can clear the error in the Status menu. I updated my v2s last Saturday and set up the HD OSD in bf4.4, chose the DJI HD preset, and didn’t have to do anything in the CLI. It works fantastic. I flew four packs with the O3 air unit and two batteries with the Avata with zero issues. I’m assuming the preset took care of the CLI stuff JB did because I sure as hell didn’t do any of that and it worked perfectly. Thanks for the vid, JB.
Have you tried with vista, does it support HD OSD without WTFOS?
@@harishgowtham_vista Support hd osd with BF 4.4 and WTF
@@harishgowtham_, no I haven’t. I’ve only got O3s unfortunately.
I already update the firmware to the newest but the canvas option for change to HD its still not appears. There is only brightness and scaling option
@@andifu1630 you have to do the update while in O3 air unit mode not fpv like JB says in this tutorial and then it will work properly.
Thanks so much.. I asked someone else a few weeks ago why my cross hairs on my Pavo Pico were off to the right on my OSD. They told me to make sure the OSD was on HD. Which it was in Betaflight. They didn’t tell tell me to go into my goggles and change the settings in my goggles. Love the way you explain FPV.
In case anyone gets the warning message “Incompatible goggles, air unit and camera” which happens if you swap just the camera or just the vtx (they come calibrated together from the factory..) you will need to plug it in to Dji assistant 2-Consumer Drone version, and calibrate them. In this case you have to connect to power. Then after you plug in power, a pop up will automatically ask you if you would like to calibrate the camera, and you choose yes. Only takes a few seconds, and it’s all good. I went through this after shearing the m1.6 screws on one of my o3’s, and swapping it out.. just something to keep in mind..
Thanks Mike I couldn't figure that shit out tha life of me owe ya one
Lol you swapped it out because of that? You never heard of double sided VHB tape? It’s actually better than screwing it in
@@SikhFPV Perhaps if doing so from the beginning, but the screws hold the two halves from falling apart as well. Using VHB would only be securing the bottom metal cover. You could argue that zip ties would solve that issue, but that was my first o3 build. No idea what the heat was going to be like. Easier to just swap it out and order screws and replace. Rather than gambling on ruining a brand new $170 vtx.
Hey joshua, do you think you could make a “refresher “ video for ppl that have been out of the hobby for a long time? Like covering the basics and some of the new stuff? 🙏🏼
@joshuabardwell
This would be amazing.. as someone that took a break right before the whole FrSky Acsst change thing, and is now getting back into it, it’s all very different!
All my quads still run 4s on F3 fc’s!
ouch thanks M Bardwell ! once again your video give the solution and make the stuff work...what could we do without you ?
Thank you for another informative video.. workout you us old guys would be LOST! THX JB🙏🙏🙏👍
MIKEY
Thank you so so much! This helped me solving my complete problem with O3 and learning a lot about it in a few minutes!
I've been searching for the fitting files to load from local space, but found no presets in the internet for DJI O3. -.-
Legend, just got my V2s and an O3... threw this in and walah, perfect
I like system critical information displayed right in the center
Thanks! Was struggling to get this to work on my new drone!
Also works great in Kiss Ultra with latest firmware. 🤓
Dang JB...u saved my butt again! I was having big time issues trying to figure this out. Many thanks!! BTW...became a patreon subscriber today. Stay safe brother.
Thanks for the tutorial, Joshua! 😊
Stay safe there with your family! 🖖😊
You can choose MSP+DP in the ports tab in configurator now.
Yes but you still usually have to set osd_displayport_device manually because DJI didn't implement the full vtx-FC communication protocol. Currently, only WTFOS is 100% sure that you don't have to manually put that CLI line in.
You didn't typo the osd_canvas_height, you just told us to set height 53 and width 20 and these are the wrong way round.
Ayyyyyy
I just ran into that. I came here to see what others were saying. So thanks brother
Thank you so much Joshua! You are a life and headache saver !
many many many many thanks Joshua you deserve all
Thank you, you really helped me with the same problem! Although it may seem obvious, it's not for many
Because of you Mr. Bardwell , i've successfully handed over my money with confidence. Soon, i promise i will drop some cash towards you!
this video saved me and got you with another patreon supporter.
Awesome! Glad to help.
Witout you Sir fpv would be only for Rocket egineers mega thanks from germany
😀 This is just the information I was looking for!
Only, I'll be sure to set my width and height to 53 and 20 so I don't have a tall narrow FOV like you just set. 09:07 😁
Thank you for that. I was all discombobulated trying to figure that one out😂
Great! On goggles v2 with o3 works! Thank you
perfect video.
thanks again Joshua
This should help make it easier for people to set up o3 in betaflight. definitely annoying when I tried to enable HD as an early adopter in BF 4.3 with o3 and it didn't work. dunno if I really want it smaller now I'm used to it and it didn't look that bad lol. not that big of a deal for me.
Can these different onscreen displays be edited using Betaflight with a DJI Avata 2?
I'd love to be able to edit what is shown and where if possible or does DJI lock all that down on their own drones?
Many thanks.
Thanks you so mutch it works on my V2
Could you do a video on how to flash BF with the speedybee app for those of us without a pc?
You helped a lot, thank you very much
Thank your very much!
😘
can you do a camera manual parameter setting video on night day and cloudy settings 03 unit .. thanks 🥰🥰😃😃😃
JB thanks for this helpful video!! 👍👍🇺🇸🔥
Hi sir, can u give me some advices for setting up OSD and canvas for dji vista especially caddx nebula pro vista kit?
Thank you so much. 👍🤝
I am not able to get home direction arrow of my gps on my dji goggles 2
I am up to date can see all elements but not the home arrow thing
I couldn’t get my dji controller to work anymore went I updated to 4.3 firmare, had to downgrade back to get it back working
Thanks Joshua
Nice please tell me how to turn off air 3 with rc 2 out display
thanks! love the content
Hey, there's some voodoo with my Vista nad V2 googles going on. I have WTF, and HD OSD workson every quad with ori dji air unit, but on Flywoo Firef;y Baby with Vista, I can't turn on the HD option is osd tab. As soon as I click it, it goes back to auto, ntsc or pal...
Thank you sir 🙌
nice one BRO thanks
Is this only works in Betaflight 4.4?
Thank you in advance.
And great video like always Joshua!
Yes correct.
@@JoshuaBardwell thank you so much for the help, i will update. Best regards from Spain profesor! ❤️
thank you !!
HI! can not see HD option in Configurator osd page.....
How did you recorded the O3 Air Unit DVR is there any video on that?
Can I use different dji cameras with the air unit 3 like the wasp or pheonix or nebula with the unit 2 and if I am able to is it possible to switch between the cameras quickly while I'm already our flying if I have both the original 03 camera and another one? Also which current dji cam is best for low light but still have good picture/resolution?
So I've done all this it works fine but with HD canvas on I get HORRENDOUS range like 25ft. It is going out of low power mode. It asks works great if I have HD canvas mode off and msp off in ports tab. Switch either of those on and I get no usable range.
Супер відео, екранне меню в Гугл 2 запрацювало так як треба в INAV 7.1.0. Дякую! Ще б з компасом розібратись, ні як не можливо нормально відкалібрувати.
Great Content
I can’t see the canvas mode in goggles 2, and I just updated the goggles and O3
Does this work with V2 goggles or is it limited to G2?
need to know that too
I think just g2 but really hoping I’m wrong
@@benjaminfpv works on v2 as well. Just updated them
@@chrisbee5481 for real? Have you tried it?
@@benjaminfpv yes works
Works on a v2 as well? Need to update to?
I just updated to latest FW and that is affirmative on the V2's
What about inav?
As long as there is no Font with Fixedwing-Symbols, it still won’t be nice I guess…
how do you make the 03 air unit power on and connect to the goggles without a lipo? it get sooooooooo hot on the bench :(
Hello Joshua, do you think the C224 1900kv by AxisFlying is a good replacement motor for Chimera 5?
Eagle Tree Vector or bust.
Just got iNav OSD working with my O3 Air and Goggles 2. Has there been a fix yet for the "?" character that is seen on screen instead of the proper characters as seen in iNav config?
I started using Fettec FC with kiss firmware, and I am only can see the voltages, I am wondering if this is DJI lacking for support or is kiss problem, I might not even try kiss anymore.
can this work for the OG AIR UNIT
?
One wonders if this would be possible to do with my V2's goggles?? I was looking for the canvas mode.. and can not see it!!
You need to root them and flash wtfos.
hi can you set artificial horizon on this ?
@ Joshua can we have the right settings for the 03 / vista/ airunit or are they all the same?
thanks crack
Second. And fun i was planning on getting a drone with an o3. This will help.
i have no available "Video format' options. "Get canvas" also not working
You must be on BF 4.4 or newer.
Is this only for o3 units or will it work with goggles 2 and vista units?
Hi Josh, new to BF and still learning... I've come from DJI drones - My question is what if my BNF preset im using for my nazgul F6 V2 required 4.3.2 firmware to be flashed to use, can i still do this? Or because im using the 4.3.2 preset i can't?
Thanks
No I don't think 4.3 can do this. Definitely not HD.
@@JoshuaBardwell oh ok. Thanks for your help, appreciate the reply 🙏
can you help me josh? osd from fettec fc to the goggles 2 and air unut 03? how does it work? does it work? 🤯🤨
iNav work?
nope i did everything u told me and im still get no no no osd if i disarm it will show me osd stuff but nothing
Can I ask you something plz?
Hey mate, I havent heard you talk about this but i know you know it all about fpv :) can you only have one additional working msp selected in the PORTS tab?(apart from usb) i have the one you must keep on which is USB then i have the uart my 03 air unit goes through and osd works fine but when i select msp for the uart my onboard FC bluetooth goes through my osd stops working and BT also doesnt work unless i turn off uart for 03 air unit :( how annoying, I jus wanna tune my quad without my computer at the park with osd.
Hello, thank you for the video. However I have an issue, I have followed all the steps but when I connect the battery and put the goggles, I don't have any OSD information on my screen... Can someone please help me? Thank you
Ok fixed... I was on the wrong UART =-(
@@thomas-1477put what happened to you 😊
If i upgrade ym fpv goggles to the latest firmware does it still work with the wtfos mod?
I downloaded a new Betaflight Configurator on my Mac, version 10.9.0, but the Firmware its 4.3.1 instead of 4.4? What I missed?
The version of the configurator on your computer is separate from thr firmware on your fc. You have to uidated the FC firmware separately.
Takk!
Nao consigo abrir a unidade dji o3 no windows 10
Finally!
Hi. Is this update gonna work for Dji goggles v2? Thank you
For v2 goggles, root and install wtfos.
@@JoshuaBardwellin version v1.00.0606 or v1.00.0500?
I flew with a pilot last sunday who had the fancy font on dji googles v2.. so it is possible, but requires root.
Only with Vista vTX not o3.
@@JoshuaBardwell gocha!
Will this update lock googles v2 to o3 only as was announced before ? or im mixing things up ?
No that isn't true. You can still use Vista.
Would this work for the Avata?
No. The Avata doesn't have an OSD like this.
@@JoshuaBardwell thanks
I still don't have osd I have v2 goggles. Any idea?
In configuration u have enabled the option "Show OSD"?
What will happen if I decide to fly in 4:3? Would osd elements move on its own?
No osd stays wide , I don't mind wide elements in 4:3, things on edges are a bit harder to see (goggles 2)but I just keep important stuff near the center anyways
@@badfourlife I appreciate that!
Help! DJI 03 canvas mode does not work. I've pretty much exhausted all ideas to get the OSD working on my goggles 2. No OSD information is displayed at all. The full camera image is displayed with the base DJI information:
Betaflight 4.4.1
DJI Goggles: V01.05.0000
DJI Air Unit: V01.02.0000
Crossfire latest version
Mamba F722_2022B flight controller
Flight Controller factory connector uses Uart4 to connect to DJI air unit
Peripherals dropdown set to VTX (MSP+Displayport) on Uart4 with Configuration/MSP slider on
OSD Option on Configuration page slider on
Video format on OSD page set to HD
DJI Goggles 2 display option set to HD
osd_canvas_width = 53
osd_canvas_height = 20
osd_displayport_device = MSP
DJI 03 RX connected to flight controller TX
DJI 03 TX connected to flight controller RX
Any ideas would be helpful. Thanks
Were you able to find a resolution on this?
Betaflight>Configuration>'Show OSD' enabled. Did u check this?
you swapped height and width i think.. width 53 and height 20 9:04
Hey Josh, I did everything you mentioned and managed to get all my OSD up on my goggles 2, except for GPS-related displays. Any idea how to fix this? Thank in advance!
Hey there, I have the exact same problem. Did you manage to find a fix for it by any chance?
@@kylespencer4037 hey bro. I found the issue alr. Are you using o3 air unit that connects directly to your fc with a connector? What radio are you using?
@@DopeyFPV Yes exactly, my FC connects directly to the air unit. I'm using the DJI controller 2
@@kylespencer4037 ok your gps might be connected to the same uart as your sbus wire from the dji o3. Just try a different uart for your gps. For me im using elrs so i just had to take that yellow wire out.
Thank you so much man! Tried the different URAT and it worked!@@DopeyFPV
This works on inav too ?
Yes but the setup steps are a little different
@@JoshuaBardwell is it possbile to explain ? Because as i can see inav 6 is replicating BF 4.3 canvas mode so am not so sure if this will work..
I cannot get this thing to show on my goggles. V2 I have the O3 air unit with the tmotor F7 flight stack. I updated both goggles and vtx.
Any pointers
Goggles are on HD Mode and the CLI commands were imputed.
HD video format is on ok beta flight and my uart port is set to the VTX display
Go to CLI type
set osd_displayport_device=msp
save
Did you enter that one already?
Would this work when using a vista with the goggles 2 ? Does the vista have a different canvas size?
yeah it works
canvas is the default. only wtfos is different
What if I have V2 goggles is it the same process
No. You need to root and install wtfos. I just released a video like 3 days ago showing how. Title wtfos butter superpack.
@@JoshuaBardwellcan I use my v2 with a 03 an can I still get my osd
@@JoshuaBardwellv2s are rotted with Wtfos installed. I want a 03 to get sound in my flight videos. Also can I still use Wtfos to add OSD to my 03 flights like my vista lite
O3 does not record sound sorry to say.
V2 goggle can be used with O3. To do this, you switch the goggles into "O3 mode" in the menu.
When v2 is used with O3, WTFOS does not apply. It is not relevant. It doesn't exist. When the goggles are in O3 mode, the entire concept of rooting and WTFOS doesn't exist. It has no effect at all.
If you want to record your OSD, either use a Vista with V2 and WTFOS, or use Goggles 2, which can record OSD internally.
I cant find the hd option on setting>display. Only brightness and display scaling
Same. Did you figure it out?
Notyet
@@andifu1630 I updated to latest firmware and it works now.
Already on the newest but still not appears :(
Already on v01.06.0000
Ahhhhh sooooh meesta bardwell deriver again
Hello. Please tell me is osd recorded on video?
On goggles 2 yes.
@@JoshuaBardwell Is it possible on goggles v2?